Search Documents

By J. F. Colinet, W. R. Reed, J. D. Potts

Dust surveys were conducted at six underground coal mines to determine if deep-cutting practices expose face workers to higher levels of respirable dust. The surveyed mines were able to successfully mine deep cuts without significantly increasing the dust exposures of face workers. In general, all of the selected mines exercised good dust control practices by maintaining water sprays, scrubber airflows, proper curtain setback distances and providing sufficient airflow to the active faces. For exhausting face ventilation, field data indicate that scrubber airflow is the most important factor for controlling dust. Data collected for this study indicate that 20-mesh screens should be cleaned for every 12.2 m (40 ft) of advance, because 22% of the deep cuts surveyed for this study experienced a 20% to 35% decrease in scrubber airflow over the course of the cut. For blowing face ventilation, field data and past research indicate that dust control is aided by maintaining a proper curtain-to-scrubber airflow ratio of 1.0 (measured before scrubber activation), as well as a curtain setback distance that allows the miner operator to stand at the mouth of the curtain for the entire cut. Dust levels on the bolting faces did not appear to be affected by the longer cycles associated with deep-cut mining when good ventilation practices were used.

Jan 1, 2011

By E. L. Reed

This paper addresses the state and federal permit- ting requirements and regulatory constraints associated with the development of new "grass roots" surface coal mines in the Western United States. Since a major portion of new coal development in the West will be on federally leased coal in Wyoming, my comments are directed towards that geographical area. This will give the reader some insight into the current regulatory framework within which western mining companies must operate-i.e., the major applicable state and federal laws and regulations, the more important state and federal regulatory agencies, and the major construction and operating permits that are required. Before discussing the impact of the regulations on our business, I would like to tell you something of my company and then briefly discuss Exxon's forecast of the long range outlook for coal. Carter Mining is an Won affiliated surface coal mining company. Exxon became interested in the coal business in the mid 1960's with the recognition of the future need for alternative fuel sources. Since that time, it has acquired coal reserves located in Wyoming, Montana, North Dakota, Arkansas, Texas, Illinois and West Virginia. Carter's first surface mine, the Rawhide Mine, located north of Gillette, Wyoming began production in August, 1977. Our second surface mine, Caballo, located just south of Gillette, began operating last October. We have a third block of federally leased coal just east of Gillette. By 1985 we anticipate Carter's western surface mines will be producing at an annual rate of 30 million tons, subject, of course, to successful market development efforts and regulatory considerations. Rawhide will ultimately have a permitted capacity of 24 MM tons per year. The coal at Rawhide is in two seams; one 80 feet in thickness and the other 20 feet (including a 6 to 10 foot parting). A large shovel is used to remove the overburden, and a similar shovel and dragline are used to mine the coal. Caballo has a 75 foot seam; otherwise it is similar in design and operation to the Rawhide Mine.

Jan 1, 1979

By Jim M. Johnson

INTRODUCTION The facility water balance and maintenance of sufficient excess storage volume in the solution control system are often amongst the most critical facets of design and operation of heap leach facilities in cold, snowy climates. The purpose of this paper is to summarize and discuss climatic and operational factors which have a significant impact on heap leach water balance evaluations in high snowfall climates. Example water balance simulations are presented for proposed heap leach projects located in areas subject to high snowfall in the northwestern United States. The climatic data input to these simulations represent both net evaporative and net precipitation climates. FACTORS AFFECTING WATER BALANCE EVALUATIONS The combined effects of seasonal operations, re1atively low evaporative losses, and potentially large inflows to the solution control system from snowpack and spring storms require an enhanced awareness of the factors which impact facility water balance. Unlike operations at mines in more arid climates, seasonal excess water rather than a shortage of make-up water is the rule. A thorough understanding of a number of factors, including regulatory constraints, climatic influences, and impact of operating philosophy and techniques, is critical to successful development of an incident-free heap leach operation under high snowfall climatic conditions. A process water circuit schematic for a typical heap leach operation is shown on Figure 1.

Jan 1, 1988

By Seppo] [Kreula

Outokumpu Oy has acquired considerable experience with on-stream X-ray fluorescence analyzers and with computer control of flotation processes over several years. It became evident at the outset of this work that a reliable and accurate on-stream analyzer was more than a collection of different pieces of hardware linked together. Extensive work was done to develop an integral analyzer system, beginning with process samples through the spectrometer to report typewriters, recorders and the control computer. To date, over ten Courier-300 analyzer systems based on this development have been installed world-wide, several of which provide the key information for successful computer control systems. Computer control of flotation processes has been under development at the Pyhäsalmi concentrator since 1968. Two different control strategies have been implemented. The copper flotation is controlled by means of a mathematical model and economic criteria, whereas the "evolutionary operation principle" is applied to the zinc flotation. The computer control system installed at' the Vuonos-mine has been developed according to the same guidelines. In order to consolidate this wide experience, a flotation computer control system, Proscon-100, was developed by Outokumpu Oy, and the first system was installed at Kotalahti in 1972. In addition to the technological experience, enough information has also been gathered to illustrate the economical, benefits accruing through the use of these advanced tools of automation.

Jan 1, 1973

By S. A. Shoop

Vibrations from thirty-seven blasts were monitored using three seismographs. Data analysis showed that square root, cube root, and site-specific scaling predicted ground motion with equal reliability. Imprecise prediction is caused by geologic and blast variability, particularly inaccurate delay times. Vibrations at some mines were consistently lower or higher than vibrations reported in the U.S. Bureau of Mines studies. Regulations based on USBM data could then be too conservative or lenient. Predominant vibration frequencies were generally less than 50 Hz, but several blasts had significant energy up to 125 Hz. In some cases energy was concentrated at frequencies corresponding to delay intervals.

Jan 1, 1983

By W. E. Benton

Diatomite or diatomaceous earth is a siliceous sedimentary rock principally made up of the skeletal remains of the diatom, a microscopic, single-cell aquatic plant related to algae. The unique structure, chemical stability and physical properties are the major attributes of diatomite not met by other forms of silica. The production of diatomite was down in 1982 vs. 1981, reflecting the worldwide recession. The principal markets for diatomite products continue to be basically filtration and fillers. The outlook is for small but steady growth into the 1990s.

Jan 1, 1983

By Frank H. Buchella

Principal factors influencing equipment selection can be grouped into five basic categories. Tonnage Requirements, Ore and Waste Loading, transporting, and ground preparation equipment are largely determined by tonnage requirements. Generally, the greater the tonnage requirements, the larger the equipment size selected. Large size equipment is appropriate for a production of about six million tons (total) per month, medium size for three mil- lion tons, and small size for one million tons or less.

Jan 1, 1973

By Lynn I. Kelley

Industrial-mineral production contributes on the order of CDN$1.5 billion per year to the economy of Saskatchewan, Canada. Potash is the primary industrial mineral produced in the province, followed by aggregate, sodium sulphate, salt, potassium sulphate, peat, clays, silica sand, calcium-chloride brine, and "clinker." Potentially economic deposits of kaolin, diamond, and building stone are under evaluation. All of the major deposits of commodities discussed here are located south of lat 56°30'N. Most of the locations are presented on Figure 1 POTASH Saskatchewan supplies approximately 30% of the world's demand for potash. Eight conventional underground mines and two solution mines produced an all-time high of more than 13 million metric tonnes of potash (KC1) (8 million tonnes K2O equivalent) in 1997, valued at over CDN$1.4 billion. All of the mines exploit the middle Devonian Prairie Evaporite. The four potash-bearing members of the Prairie Evaporite underlie much of southern Saskatchewan and extend southward into North Dakota and Montana and east- ward into Manitoba (Fig. 2). Halite and anhydrite separate the potassic members. The evaporite beds locally are interrupted by solution structures (anomalous ground). Some of the structures may be related to deep-seated tectonic features.

Jan 1, 1999

By B. H. Johnston, B. N. Doyle

Introduction In 1983-84 Kidd Creek Mines Ltd. in Timmins, Ontario, started up the second commercial zinc pressure leaching plant based on the Sherritt Gordon Mines Ltd. direct pressure leach process. The first plant using this process was that of Cominco Ltd. at Trail, B.C. (Parker, 1981; Martin and Jankola, 1985). The Kidd Creek plant was constructed to take advantage of the extra capacity that the existing purification, cell house, and casting sections had in comparison to the roasters and acid plant. In addition, pressure leaching offered flexibility in other areas such as treatment of low grade concentrates. The process design package and the detailed design of the autoclave system was carried out by Sherritt. The detailed design for the rest of the plant was done by Cambrian Engineering Ltd. under the direction of Kidd Creek. The construction and commissioning of the plant has been described earlier (Johnston, 1983). This paper describes, briefly, the application of the direct pressure leaching process for zinc concentrates and the integration of the pressure leaching plant into the main zinc plant at Timmins. It discusses some of the startup problems and changes made to the plant. The damage following a fire inside the autoclave is also described. The subsequent repair and recommissioning of the autoclave has enabled Kidd Creek to demonstrate the originally sought advantages of pressure leaching and to take advantage of their extra cell house and casting capacity to produce more zinc. Process principles The development of the direct pressure sulphuric acid leach of zinc sulphide concentrate at temperatures above the melting point of sulphur and at elevated oxygen pressure has been described in detail in a number of papers (Martin and Jankola, 1985; Johnston, 1983; Veltman and Bolton, 1980; Kawulka et al., 1975; Veltman et al., 1977). The most significant aspect of the process is that sulphidic sulphur is converted to elemental sulphur in reactions that can be simply described as follows. ZnS + H2SO4 + 1/2 O2 ZnSO4 + S° + H2O (1) FeS + H2SO4 + 1/2 O2 FeSO4 + S° + H2O (2) The rates of these reactions increase with temperature. However, at temperatures above the melting point of sulphur, 12°C, the presence of a surface active agent is necessary to prevent the occlusion of the sulphide particles by elemental sulphur and the consequent termination of the leach. The zinc that is dissolved according to reaction (1), after purification of the zinc sulphate solution, is recovered by electrowinning. The iron that is put into solution according to reaction (2) is further oxidized to the ferric state and subsequently, as the acidity decreases, precipitates as hematite or as complex basic sulphates. MINERALS AND METALLURGICAL PROCESSING Examples of this are shown below. 2FeSO4 + H2SO4 +1/2O2 - Fe2(SO4)3 + H2O (3) Fe2(SO4)3 + 6H2O - Fe2O3.3H2O + 3H2SO4 (4) 3Fe2(SO4)3 + 14H2O - 2(H3O)Fe3(SO4)2(OH)6 + 5H2SO4 (5) (hydronium jarosite) The conventional zinc process involves concentrate roasting to produce zinc oxide and sulphur dioxide. The zinc oxide is leached in spent electrolyte and the sulphur dioxide is converted to sulphuric acid. The pressure leaching process can, therefore, be used to replace conventional concentrate roasting, sulphuric acid manufacture, and atmospheric leaching with one unit operation. Integration of pressure leaching into the Kidd Creek flowsheet A block flowsheet of the Kidd Creek zinc plant, with the new pressure leach plant integrated, is shown in Fig. 1. The original plant, which was constructed in 1972, is based on standard electrolytic zinc plant technology. Concentrates are dead roasted to remove sulphur. Sulphur dioxide is treated to produce sulphuric acid. Calcine is leached in two stages using cell-house electrolyte. Iron is precipitated as jarosite and solutions are purified to remove copper, cobalt, nickel, and cadmium to provide feed for a partially mechanized cell house. Zinc is plated from solution, and the resulting cathode is melted, cast, and sold (Johnston, 1983). The integration of the pressure leaching plant into the main zinc plant is relatively simple. As shown in Fig. 1, a fraction of the zinc concentrate and spent electrolyte are fed to the pressure leach autoclave, while part of the calcine from the roaster is used as a neutralizing agent in the oxidation step along with. the jarosite leach solution. The main exit stream from the pressure leaching plant is the slurry discharged from the oxidation step, consisting of neutral zinc sulphate solution, unreacted calcine, and precipitated iron oxides. This slurry is transferred to the neutral leach step in the main zinc plant. The leach residue from the pressure leaching step, consisting of basic iron sulphate and elemental sulphur, is washed and impounded along with the jarosite residue produced in the main plant.

Jan 1, 1987

By Franklin B. Woodbury

As part of its goal of helping maintain an adequate supply of minerals to meet national economic and strategic needs, the U.S. Department of the Interior's Bureau of Mines is evaluating alternative technologies to treat oxidized taconites. Since process control is an essential element in the application of these process technologies, research was performed with a prototype monitoring system. A Californium-252 neutron source and a thermal neutron capture- gamma ray spectra analysis method was utilized to measure the amount of iron and the percent solids in the process slurries. The concentrate and tailing streams in a 410-kilogram-per-hour (900- pound-per-hour) pilot plant employing a selective flocculation and cationic flotation process were monitored. The results obtained showed that the thermal neutron capture-gamma ray reaction can be used to provide process control parameters.

Jan 1, 1979

By Stanislaw Nawrat, Waclaw Dziurzynski

An increasing concentration of coal production, especially in the circumstances of intensive methane inflow makes the coal mine managing staff apply new techniques of safe mining. It paves also the way for scientists to develop new directions of investigations and implementation of state-of -the- art technical solutions. Simultaneously, it could be noticed that the funds assigned for expansive 'En situ ' investigation are continuously decreasing. Better and better results are reached when applying computer technique in calculations of the parameters of ventilation process. Recent theoretical and experimental investigations of air and gas (methane) flow in longwall areas with caving, combined with the implementation of methane drainage system allowed to create, a mathematical model and consequently to elaborate a computer supported numerical simulation of discussed phenomena. The mathematical model has been modified and the simulation program was prepared in such a way that the software is convenient for a user looking for an optimal solution. The paper presented the methodology of optimal choice of following parameters: - ventilation system - rate of flow through the wall. The procedure takes into consideration keeping a safe level of concentration methane in air flowing through the longwall as well as the criterion of maximum methane concentration within the methane drainage pipe line. Results of variant computer simulation regarding the longwall with caving are shown in graphs and tables.

Jan 1, 1995

By W. A. Wright

The use and abuse of social media restate common employee relations issues. Business solutions to these issues require advanced preparation. Employers should establish and enforce social media policies to guide their reactions to employees? social media posts that reflect on the employer and its business.

Jan 1, 2011

By J. M. Marek

The determination of the proper cutoff grade for an open pit metal mine is based on economic criteria and the operating philosophy of the mining company. Previous papers have dealt with the balance of a fixed mine production capacity versus economic return. Mine production capacity is often controlled by the amount of mining equipment and the working area in the pit. A complete cutoff grade strategy is a balance of economic return of mining higher grade material versus the capital costs of additional production capacity and the operating cost of moving the waste and low grade material to assure proper ore release. An approach to the problem is presented which is based in part on work by previous authors and provides guidelines to proper cutoff grade strategy encompassing the time value of money and variable commodity prices.

Jan 1, 1985

By E. E. Malouf

For centuries small amounts of copper have been recovered from acid mine-drainage waters. In recent years, the expansion of copper-bearing waste dump leaching for copper recovery has established a technological basis that is rapidly converting the art of copper leaching' into a science. Leaching of copper, whether from copper-bearing ore or waste, follows well established chemical reactions. These reactions are commonly in an acid circuit, but where leaching of copper is to be made in rock that is a high acid consumer, ammonia and ammonia carbonate, as well as cyanide leach solutions, can be used effectively. Current hydrometallurgical processes are being applied at an ever increasing rate to recover the trace amounts of copper in copper mine waste by in-place leaching. Currently approximately 300, 000 tons of copper are produced annually in this manner where as recently as ten years ago, only one-eighth of this amount of precipitate copper was produced.. Where copper occurs as an oxide in higher concentrations as to be classified as an ore rather than waste, then the hydro-metallurgical processes are applied as percolation or agitation leaching in vats, pachuca tanks, or prepared heaps. This approach gives better control over the recovery of the leach solutions, particularly in the processes where ammonia or cyanide leaching agents are to be used.

Jan 1, 1972

By K. C. Nathsarma

An attempt was made to extract niobium oxide from ~98.5% Nb2O5 using solvent extraction processes. Nb2O5 is used as the feed material in carbothermic reduction processes aimed at producing high-homogeneity, super-conductor-grade niobium on a laboratory scale. The Nb metal used for superconductor applications requires a residual resistivity ratio (RRR) > 300, which in turn needs a stringent purity of Nb and allows impurities (substitutional and interstitial) in ppm levels only. In this paper, solvent extraction of niobium was studied under various experimental conditions, such as effect of different extractants, concentration of methyl isobutyl ketone (MIBK) in the organic phase and concentration of various acids. The concentrate was digested with hydrofluoric acid, with ammonium fluoride (NH4F) as a stripping agent. The extraction of niobium from low hydrofluoric- (HF-) bearing solution was found to be low. Thus, various concentrations of hydrofluoric acid and sulfuric acid, as well as hydrofluoric acid and hydrochloric acid, were investigated towards obtaining a maximum amount of niobium in the filtrate and a minimum amount of niobium in the residue. A McCabe - Thiele plot for extraction of niobium from the aqueous phase, HF-bearing solution using HCl with 85% MIBK in kerosene has been constructed to determine the O:A ratio and the number of stages of the process.

Jan 1, 2011

By K. C. Nathsarma

An attempt was made to extract niobium oxide from ~98.5% Nb2O5 using solvent extraction processes. Nb2O5 is used as the feed material in carbothermic reduction processes aimed at producing high-homogeneity, superconductor-grade niobium on a laboratory scale. The Nb metal used for superconductor applications requires a residual resistivity ratio (RRR) > 300, which in turn needs a stringent purity of Nb and allows impurities (substitutional and interstitial) in ppm levels only. In this paper, solvent extraction of niobium was studied under various experimental conditions, such as effect of different extractants, concentration of methyl isobutyl ketone (MIBK) in the organic phase and concentration of various acids. The concentrate was digested with hydrofluoric acid, with ammonium fluoride (NH4F) as a stripping agent. The extraction of niobium from low hydrofluoric- (HF-) bearing solution was found to be low. Thus, various concentrations of hydrofluoric acid and sulfuric acid, as well as hydrofluoric acid and hydrochloric acid, were investigated towards obtaining a maximum amount of niobium in the filtrate and a minimum amount of niobium in the residue. A McCabe - Thiele plot for extraction of niobium from the aqueous phase, HF-bearing solution using HCl with 85% MIBK in kerosene has been constructed to determine the O:A ratio and the number of stages of the process.

Nov 1, 2011

By Elwyn King, Donald J. Dodds

"...Unfortunately, the research activities in soil mechanics had one undesirable psychological effect. They diverted the attention of many investigators and teachers from the manifold limitations imposed by nature on the application of mathematics to problems in earthwork engineering. As a consequence, more and more emphasis has been placed on refinements in sampling and testing and on those very few problems that can be solved with accuracy. Yet accurate solutions can be obtained only if the soil strata are practically homogeneous and continuous...." This statement about soil mechanics was made by Karl Terzaghi, thirty years ago and applies to a greater degree today to the infant science of rock mechanics. More uncontrolled variables are added to the already many existing in soil mechanics. Variables, such as Macro-discontinuity and in situ stress levels. In no other field of engineering are the problems as site oriented. Presently this site dependance demands the investigator or rock mechanics engineer to get his hands dirty rooting in the muck of a tunnel floor trying to properly install or readout test apparatus in a comprehensive site investigation. This paper discusses such a site investigation designed to determine the problems and solutions inherent in the driving of the Trans Koolau Tunnel. The paper will describe the various types of tests to be performed, how the results are to be used and the interrelation of the various tests themselves.

Jan 1, 1997

By J de Cuyper, S. R. Rao, J. Leja, K. S. Moon, W. Freyberger

A prolonged grinding of sulphide ores in steel mills appears harmful to flotation recovery and selectivity whenever xanthates are used as collectors. Particles finer than about 10um show a pronounced decrease in floatability. A supposition was made that the cause of the reduction in floatability of ground sulphides is the presence of metallic iron abraded during grinding and deposited on the ground particles. Electro- chemical measurements were made of mixed potentials developed by different sulphide-mineral electrodes (galena, chalcopyrite, pyrite, marmatite, pyrrhotite) in xanthate solutions, without a direct con- tact or in contact with a metallic iron electrode. These measurements showed that without a galvanic contact between the sulphide and the iron, the values of mixed potentials were in the vicinity of the xanthate/dixanthogen redax potential. When contact with iron was established, the mixed potentials shifted towards the more negative reducing or cathodic values, The shift was greater the higher was the ratio of the surface areas: iron electrode to sulphide electrode. Further, the shift in mixed potentials was greater the more reducing were the conditions on the sulphide electrode. Chemical analysis of reaction products produced on the surfaces of sulphides and in the bulk solution showed that less thiosulphate was formed in all of the sulphide-xanthate systems and that more elemental sulphur was detect-

Jan 1, 1976

By Bryan C. Smith, Duane R. Skidmore

Volumetric mass transfer coefficients and gas holdups were measured in a concentric tube airlift reactor designed for the microbial desulfurization of coal. The slurries were comprised of an acidified basal salts solution containing thirteen different weight percents of coal (74 µm Ohio #1) at three temperatures. An enhancement in the mass transfer coefficient, KLa, with respect to that measured in pure solution was found at weight percents of 5 (volume fraction solids, ES = 0.035) or less, the greatest enhancement being as great as 37% at approximately 2 weight percent (ES = J 0.014). At higher solids fractions, the mass transfer coefficient decreased with further solids additions, decreasing by as much as 91% at 40 weight percent coal (ES = 0.315). KLa increased with temperature at all solids concentrations, the greatest increase being 392% at 72°C vs that measured at 30°C. Gas holdup, EG decreased with all increases in solids loading by as much as 65% and increased by as much as 67% with temperature. KLa and EG were correlated with operating conditions separately, and the separate correlations combined to yield overall correlations for the mass transfer coefficient and for the gas holdup. The correlations are suitable for inclusion in system models devised earlier for microbial coal desulfurization processes, and may be used for design, operation and cost estimation for such systems.

Jan 1, 1989

By Sam Ash

The Murray Mine was one of the first mechanized cut-and-fill underground gold operations in northern Nevada. At the end of 2002, mine production began to decline. So the mine entered a phase of remnant mining and began preparations to close down. The remaining mining took place along the ore waste boundary in previously condemned areas and in challenging ground conditions. To remain economically viable, new techniques were implemented in operations, geology, engineering and rock mechanics. These improvements pushed the edge of known and accepted mining practices and have allowed the Murray Mine to remain in operation.

Jan 1, 2006