Search Documents

By Frank H. Madison

The percentage depletion deduction on Federal Income Tax Returns under the provisions of the 1939 Internal Revenue Code and of Sections 611 to Section 615, inclusive, of the revenue act of 1954, have created innumerable administrative difficulties, and a new interpretation of "gross income from the property" in that the Courts have expanded the ideas of what constitutes "gross income from the property" to a degree unheard of and unthought of prior to the enactment of these two codes. Originally, under the Revenue Acts of 1917, 1918, and 1920 depletion was allowable, based upon mine valuations as of March 1, 1913; if the mine was owned prior to March 1, 1913; upon cost, as of the date of acquisition if purchased subsequent to March 1, 1913; and upon a "discovery" basis if the mine was discovered after March 1, 1913, The "jab" for mine valuations as of March 1, 1913 and for discovery valuations and depletion was not as bad as it has been made out to be. Thousands of valuations and estimates of reserves were made and agreed upon between taxpayers and Internal Revenue Service engineers and as the years went on the answers have been found to be "reasonable." However, human nature being what it is each case was a battle of wits - of a sort - and many resulted in severe differences of opinion and litigation. As tax rates increased the situation was not bettered. I could talk for several hours on this phase of depletion but it is all past now andwould not give any real service or better understanding of the matter.

Jan 1, 1958

By George K. McCord

It is a pleasure to participate in this Fall meeting of the Society of Mining Engineers to discuss energy conservation trends in the cement industry. Energy is the "life blood" of American industry, and the ability to use available energy resources efficiently may well determine the future of our nation and of its industries. The Federal Energy Administration has classified cement manufacture as one of several energy-intensive industries in the U.S. and has selected the Portland Cement Association to make a detailed study of possible energy conservation measures. Member companies of the Portland Cement Association represent about 85% of the cement producing capacity of the United States and 100% of Canadian capacity. Stated briefly, the purpose of the Association is to extend the uses of portland cement and concrete through research and development, market promotion, education, and public affairs work. PCA's general offices and research laboratories are located in Skokie, Illinois. Our staff of engineers, scientists, and research personnel make the PCA uniquely qualified to perform an energy conservation study of the kind requested by FEA.

Jan 1, 1975

By A. H. Summers

The La Choya mine is located 55 km south of Sonoyta in northwestern Sonora, Mexico. Mineralization is controlled by a 40 meter thick thrust fault zone which created a permeable host for the metal-bearing hydrothermal solutions. The ore body is mined by open pit using wheel loaders and truck haulage. Gold and silver are recovered from low grade ore by heap leaching followed by carbon adsorption.

Jan 1, 1997

By Felicia F. Peng

An economic analysis for evaluating coal preparation plants in the Appalachian Region is presented. A complete coal preparation plant which includes multi-streams and/or multi-stages coal cleaning circuits, complete closed water circuits, environmentally acceptable refuse disposal and reclamation systems is used to determine the capital and operating costs. The plant is capable of producing metallurgical grade clean coal or deep cleaned steam grade coal for future power generating plants use. Utilizing a profit maximization as a decision criterion, an optimal yield, and optimal coal clean¬ing circuits, closed water circuits, and disposal and reclamation systems for a given coal characteristic may be selected among the process alternatives by using a process simulation-economic model of the coal preparation plant. A deterministic analysis is used to calculate the discounted-cash-flow interest rate of return (DCFIROR) and project the selling prices, and determine the Return on Investment (ROI) for the cases of 32.65% and 52.74% plant utilization with producing two cleaned products. Sensitivity analyses are performed to quantify the effect of total capital investment, operating cost, run-of-mine cost and yield on an economic criterion-ROI and selling prices. A probabilistic evaluation using the Monte Carlo simulation technique is further made to quantify the risk involved in obtaining the desired profit levels. The results of the economic analysis for a given coal preparation plant configuration and characteristics of raw coal indicates that the selling prices of producing two cleaned products are greatly affected by the change in percent of plant utilization (production schedule), yield, and run-of-mine cost, and total capital cost. The sensitivity analysis also shows that the total capital investments has a three times greater effect on required selling prices than operating costs. The risk analysis shown that the overall economics look very attractive with current coal sale prices and 52.74% plant utilization.

Jan 1, 1979

By Charles H. Rice

Coal liquefaction processes can be divided into two broad classifications - direct and indirect. Direct liquefaction processes, in general, slurry coal with a solvent and react it with hydrogen under elevated temperature and pressure. Indirect liquefaction is the term applied to processes in which coal is first gasified to generate a synthesis gas of carbon monoxide and hydrogen. The synthesis gas is then converted to various types of liquid fuels by the proper selection of catalyst and conditions. The first experiments on direct coal liquefaction were undertaken in 1933 by Bergius. Development and commercialization of the Bergius concept was accomplished mainly through the effort of I.G. Farben at the Ludwigshafen plant of its subsidiary, Badische Anilin und Soda Fabrik A.G, under the leadership of M. Pier (1). A demonstration plat having an annual capacity of 100,000 tons of coal was built in Leuna, Saxony in 1927. Six years later, Imperial Chemicals Industries, Ltd., commissioned a plant in Billingham, England (2).

Jan 1, 1981

By Bülent Erdem, Zekeriya Duran, Tuğba Doğan

The objective of this study was to evaluate the potential health risk associated with exposure of dozer operators to whole-body vibration. Measurements were made on 31 dozers used in different surface mines in Turkey. Predictions of adverse health effects of vibration were based on the standards BS 6841:1987, ISO 2631–1:1997, ISO 2631–5:2004, and the EU Vibration Directive:2002. Operators experienced high and comparable levels of vibration acceleration and dose during all dozer tasks: pushing the material (DOZE), moving forward (FORWARD), moving backward (REVERSE), and ripping (RIP). Specifically, DOZE, FORWARD, REVERSE, and RIP showed high potential of adverse health effects in terms of vibration dose according to the worst-case axis and vector sum criteria and a moderate adverse health effect for acceleration according to the worst-case axis criterion. Operators of large dozers were exposed to lower levels of vibration. However, no statistically significant relationship between vibration exposure levels and the propelling mechanism and the service time of dozers, operator experience, operator age, and ground type was found.

Jun 16, 2022

By P. Perruzza, R. Grandori, A. De Biase, A. Ciamei, A. Busillo

The Turin metro alluvium soil is mainly made of large boulders, cobbles and gravel , few sand and almost no fines. This grain size curve is out of the range of application for EPB and Slurry TBMs. In order to bore 5 of the total 7,5 kms of Line 1 tunnel, two specially designed Lovat EPB TBMs were utilised in combination with a systematic non structural pre-grouting of a small volume rectangular slab just above the tunnel section. The same pre-grouting was not however applicable for lack of access on surface in some sections of the remaining 2,5 km of tunnel that had to be bored below important buildings/structures, with under ground water pressure up to 1,5 bar, with curves radius of 180 m only. For these more critical sections it was necessary to study and implement a new technical solution and improve the capacity of the TBM to work efficiently in EPB mode even in this unsuitable ground and overall conditions. After months of studies the selected and adopted solution has been to inject inside the cutterhead chamber, in addition to the almost standard foams & polymers additive mixes, a suspension of limestone powders. This with the scope of compensating the lack of fines of the natural ground with rock powders.

Jan 1, 2005

By G. J. Hartman

The Fort Cady in situ borate mining project involves recovery of boron from a mineral deposit located over 1400 feet below the surface. The resource recovery method is being developed using in situ mining technology employing weak acid solution injected directly into the ore body. As the acid contacts the calcium based ore (primarily natural colemanite), the contained borate values are digested as boric acid. This boric acid solution is then pumped to the surface by use of submersible pumps. At the surface the borate values are recovered as a finely divided solid white powder after a series of chemical reactions and precipitations resulting in the production of calcium borate. The refined product is then sold under the trade name CADYCAL 100.TM All environmental permits for up to a production rate of 90,000 tons per year have now been obtained. These permits required an Environmental Impact Study (EIS) for federal lands and an Environmental Impact Report (EIR) for the private portion of the property. Regulatory permitting took over 5 years to obtain all authorizations for this operation. The ore body has an average thickness of 118 feet extending over 273 acres. At a production rate of 90,000 tons per year with only a 70 percent resource recovery allowance, in place reserves are sufficient to sustain production for over one hundred years.

Jan 1, 1997

By G. Milojcic

The opencast lignite mines in the Rhinel and Di strict/Germany are equipped with the continuously operating bucket-wheel excavator - conveyor - spreader system. High productivity requires large capital expenditure on main mine equipment as a precondition for efficient mining. In operation, the technology employed leads to a particular cost pattern which is quite different from that of other industries. Labour, auxiliary equipment and mobile vehicles are the most important cost factors which can be controlled by the management. In this respect information processing computer systems are used for systematical and interpretable representation of operational tasks and jobs both in planning and work preparation and in recording the operational data describing the work result and the use of resources. Another aim of the project is to relieve the middle management of major part of its administrative routine work. Job-related work planning and data recording open up various possibilities of analyzing the operational procedures. This analysis shows, for example, what auxiliary machines are particularly suitable for specific tasks, and working groups can be organized so as to take account of the different skills of individual employees for the sake of an optimal work product. Computerized information processing provides the decision makers with topical information related to their respective responsibilities. The mining department of the Hambach opencast mine is the first user of the PERMAD system. Due to the favorable evaluation it has been decided to introduce PERMAD in three other mines in the course of 1992/93.

Jan 1, 1992

By K. N. Han

Copper and nickel are extracted from their elemental state, complex sulfides, ores, and other materials such as scrap by leaching them with a solution containing halogen salts - bromine/bromide, and/or iodide/iodine, oxygen and sodium or potassium nitrate. This US patented process is extremely effective yielding 98% recovery in15 minutes for the treatment of chalcopyrite and pentlandite in an autoclave at a temperature of 100°C - 150°C.

Jan 1, 2003

By R. A. Womack, Alex Ruzycki

Over the past six years, 4.5 million tonnes (5.0 million short tons) of gold ore have been heap leached at the Alligator Ridge Mine. Ore is leached in successive lifts, resulting in heap heights of 20 m (66 ft). Recoveries from each lift are determined through an extensive post-leach drilling program. The relationships between heap height, recovery rate, ore preparation, heap construction, and leach solution application are discussed.

Jan 1, 1987

By L. J. Nicks

The current U.S. Bureau of Mines research program is addressing the recovery of flake graphite from kish, a steelmaking waste product, and the use of zeolites from abundant domestic natural deposits for efficiently cleaning up mining industry wastewater. The United States is almost totally dependent on imports for its graphite needs, but this may change depending upon the results from a pilot plant being constructed by industry using Bureau technology. Standard mineral processing techniques were applied by the Bureau to recover high-quality flake graphite from kish. It was considered innovative enough to receive an R&D 100 Award in 1992, and its commercialization has the potential to supply the total U.S. demands for graphite many times over. Zeolites have ion exchange properties similar to ion exchange resins, but are less expensive and available in large quantities. Samples of naturally occurring zeolites were tested for their efficiency in removing metal ions from synthetic and industrial waste solutions. The tests focused on defining their selecting, loading, eluting, and regenerating characteristics, and on developing a method for recovering the metal ions as added value products. The results showed that the removal of metal ions with zeolites from acid rock drainage (ARD) solutions is technically feasible and that this technique has the potential for being used in an integrated chemical treatment systems approach either as a primary or secondary cleaning step.

Jan 1, 1995

By Timothy P. Smirnoff

Sustaining the region?s mobility needs, achieving projected economic growth, and maintain Midtown Manhattan as a center of regional, national and global importance has led to continued investment in commuter rail and transit infrastructure in New York City and resulted in design and construction of large underground caverns. The current plans for stations in Manhattan include New York Penn Station Expansion (NYPSE) caverns for Trans Hudson Express (THE) Tunnel Project for New Jersey Transit (NJ Transit) and the Port Authority of New York and New Jersey (PANYNJ), Metropolitan Transportation Authority Capital Construction Long Island Railroad (MTACC/LIRR) twin caverns for East Side Access (ESA) Project, and station caverns of the No. 7 Line Subway Extension Project and Second Avenue Subway Project for Metropolitan Transportation Authority Capital Construction/New York City Transit (MTACC/NYCT). This paper provides a general overview of these large caverns now in design or construction in Manhattan, the area?s geologic setting, the geotechnical factors considered and approaches commonly applied for cavern design.

By J. David Lowell

The first part of this article is a review of industry techniques and styles during the past 50 years. It is followed by my career history during the same period. The second part covers my ideas about what works in mineral exploration. These include estimates about discovery costs, thoughts about education of explorationists, organization of exploration groups and my opinions about the relative value of exploration techniques. Evolution of exploration techniques [Table 1] shows the evolution of mineral exploration techniques and styles from 1950 to 2000. During the first half of that period, there was a progressive increase in exploration drilling. During the second half, there was a decrease in prospecting and an increase in high technology, indirect exploration and a rapid increase in discovery cost.

Jan 1, 2000

By Q. X. Yun, S. H. Liu

This paper provides a new approach to determine the opening layout in underground mining methods by means of genetic programming. Based on a set of random combination of openings, the layout of openings will gradually improve with the help of genetic operations, including reproduction, crossover, mutation and fitness calculation. The optimal solution will finally emerge according to Darwinian principle: "the survival of the fittest ".

Jan 1, 2002

By Miklos D. G. Salamon

The laminated model, in conjunction with the seam element method, is expected to be a powerful predictor of subsidence due to coal mining. The fundamental solutions for the model are presented. Numerical approach to determine the roof-to-floor convergence and evaluation of ground movement are discussed. Numerical results and comparisons with field observations are given to illustrate the validity and the potential of the model.

Jan 1, 1986

By Bruce S. Brown, Jeremy P. Haile

The construction of tailings facilities and heap leach pads for gold mining operations generally requires the installation of one or more impermeable liners beneath the structures to satisfy environmental regulations and prevent the leakage of gold bearing solutions. Liners are usually constructed using clay soils or synthetic membranes, such as high density polyethelene. Low permeability soil liners can be constructed from natural clays, well graded soils with only a small clay content, or sandy soils blended with a small quantity of imported clay such as bentonite or kaolinite. The permeability of such materials, prgperly pped with good quality control, generally lies in the range of 10- to 10- cm/s, and can be designed to meet minimum prescriptive standards set by regulatory agencies. Important benefits resulting from the use of clay liners include the slow rate of penetration of a saturated wetting front, the decrease in permeability of the liner as it consolidates under the applied load of tailings or ore, and attenuation of potential contaminants in the process solutions. Synthetic liners can be attributed a finite permeability as a result of minute perforations and seaming deficiencies, and possess none of the above properties. Synthetic liners are also, by their nature, relatively thin and even a small head build-up above the liner will result in a large hydraulic gradient across it.

Jan 1, 1988

By K. E. Hjelmstad

Solution mining operations often encounter difficulty maintaining adequate leach solution flow into the ore formation because of loss of formation permeability near the injection well. Permeability loss caused by swelling and breakup of clays and fine particle migration can often be the cause of the problem. Combined permeability and leaching tests were done in the laboratory on samples of clay bearing ores to evaluate a clay-stabilizing polymer's effectiveness in preventing the problem. Test results indicate that treating the ores with cationic polymers could maintain permeabilities two to five times greater than the long-term permeabilities present in untreated ores. Both alkaline (pH 8.5) and acidic (pH 2.0) leaches were used in the permeability leaching tests. To determine the reasons for the success of the clay stabilizing polymer, clay swelling tests and zeta potential measurements were made on untreated ore samples and on ore samples treated with the cationic polymer. Test results indicate the cationic polymer could reduce the degree of negative charge on fine particles and their tendency to disperse, as well as reduce clay swelling. Test results indicate a potentially beneficial effect on operating parameters such as capacity and injection pressure during leaching, if clays and fines are kept stabilized. This may be done by treating the zone of high fluid velocity near injection wells with cationic polymers.

Jan 1, 1991

By Gennaro Gerald Marino

Vast improvement in methods of design and analysis of the long- term stability of overburden above room and pillar mines is needed. Improved methods are vital for planning and land development and for prediction above existing, presently stable, room and pillar mines. As shown on the flow chart in [Figure 1], the assessment of the long-term stability is an integral part of the site investigation process regarding mitigation of surface damage effects. In Illinois, flat farmlands with subjacent coal reserves cover vast areas. In some of these areas high extraction of the underlying coal layer(s) may not be possible since the resulting surf ace subsidence combined with a pre-existing shallow water table would make the land too wet. Thus recovery of this coal might only be accomplished by room and pillar mining where the ground surface does not subside and the hydraulics of the overburden are not significantly affected.

Jan 1, 1986

By E. Topuz, Xing Wu

INTRODUCTION The air flow in the mine ventilation network can be categorized in three ways: natural splitting, controlled splitting, and semi-controlled splitting. In natural splitting, the air flow in branches of a ventilation network apportions itself according to the aerodynamic resistance of the branches. In controlled splitting, a prescribed quantity of air is circulated through each branch. In semi-controlled splitting, flow in some branches is fixed to a desired quantity while in other branches it is split naturally. In practice, the mine ventilation networks present the latter two situations. Usually, the resistance of each branch in the network is known and the quantity of air in the working place is predetermined by safety considerations. If the number of branches whose airflow quantities are known is equal to or larger than the number of the fundamental meshes in the network, then the network becomes a controlled splitting network (Wang, 1982 a). Otherwise, it is a semi-controlled splitting network. If no booster fans are used in the network, the problem can be solved as either controlled or semi-controlled splitting networks in order to determine the main fan pressure and regulator size and location. All techniques are based on Kirchoff's flow and energy conservation laws and Atkinson's Equation. Booster fans can be used in controlled and semi-controlled splitting networks. It has been proven both theoretically and practically that using booster fans in these ventilation systems can improve flow distribution and reduce consumption of power (McPherson et al., 1985). The current techniques used in determination of booster fan location and size include simulation, linear programming, CPM and cutset operation, out-of-kilter, and critical-path crashing. These techniques can be classified into two groups. The first group, including linear programming, CPM and cutset operation, out-of-kilter, and critical-path crashing techniques, deals with controlled flow networks. The second, simulation, can be applied to the handling of semi-controlled flow networks. Mathematically, the problem of controlled splitting networks can be solved more easily than that of semi-controlled splitting networks. This is because the controlled flow network can be formulated as a linear programming problem, for the solution of which there are several sophisticated algorithms. Moreover, the semi-controlled flow network is usually modeled through nonlinear programming, for which there are no universally applicable solutions. The procedure described by Wu and Topuz, 1986, can be used to convert a semi-controlled network to a controlled flow network, and the problem can then be easily solved by the techniques used for solution of a controlled flow network problem. In practice, a mine ventilation network may change from controlled splitting to semicontrolled splitting with advancement of mining. This dynamic nature of mine ventilation makes the problem more complicated and necessitates development of new solution procedures which will consider the overall economics of the system. CONTROLLED SPLITTING NETWORK The problem in controlled splitting networks with booster fans is to determine the operational characteristic of the main fans, and the location and size of booster fans and regulators. The objective is to satisfy the air flow rate requirement for each branch while minimizing consumption of energy. The techniques used for the controlled splitting network problem include linear programming, CPM and cutset operation, out-of-kilter, and critical-path crashing. The objective function and constraints can be expressed as follows (Wang and Pana, 1971): [ ]

Jan 1, 1989