Search Documents

By G. Velarde

This paper presents the metallurgical results of column and stockpile leach tests with forced aeration to determine the usefulness of this process in the operational leaching at Sociedad Minera Cerro Verde S.A.A. The evolution of the aeration system is presented and also an innovative solution developed to overcome forced aeration’s main problem, which is the early obstruction of the aeration pipes located at the base of the stockpile, causing a decrease in air and oxygen levels and therefore a reduction in the metallurgical benefits.

Jan 1, 2006

By R. Woods

"Comments on the paper ""Formation of hydrogen peroxide by chalcopyrite and its influence on flotation,""by A. Javadi Nooshabadi and K. Hanumantha Rao (Minerals & Metallurgical Processing, 2013, Vol. 30,No. 4, pp. 212-219)The formation of hydrogen peroxide from water during the grinding of chalcopyrite in a nitrogen-sparged environment, as reported by Javadi Nooshabadi and Rao (Minerals & Metallurgical Processing, 2013, Vol. 30, No. 4, pp. 212-219), is questioned on the grounds that oxidation of water by the mineral is unlikely to be thermodynamically feasible. It is argued that it is more likely that any peroxide that had been formed would have been generated from residual oxygen in the nitrogen-flushed system than from the oxidation of water.The formation of hydrogen peroxide by finely divided pyrite had been reported by a number of authors (Borda et al., 2001; Borda et al., 2003; Cohn et al., 2006; Schoonen et al., 2006; Schoonen et al., 2010; Jones et al., 2011; Javadi Nooshabadi et al., 2013). That hydrogen peroxide is formed in the presence of oxygen in solution can be comprehended from wellestablished mechanisms. Pyrite in aerated solution is known to oxidize by an anodic process that is coupled with the cathodic reduction of oxygen (Holmes and Crundwell, 2000). The latter process has been shown to occur through the formation of hydrogen peroxide (Biegler et al., 1975; Ahlberg and Broo, 1996). The pH dependence of cathodic oxygen reduction at other sulfide minerals, including chalcopyrite (Biegler et al., 1977; Rand, 1977), implies a similar mechanism at these surfaces."

Jan 1, 2015

By Pedro D. Lasota

Chile leads the world in copper production with an annual capacity nearing 2 Mt (2.2 million st). Most of the country’s copper production, about 74%, is mined by open-pit mining methods. Open-pit mining also accounts for a major portion of Chile’s production of other commodities, including iron, gold, silver and coal (Table 1). Chile’s mining boom began 10 years ago and is expected to continue through the end of the decade. From 1980 to 1990, copper production in Chile increased 48.7%. During the same period, gold production increased 303%, silver production increased 119% and coal and iron ore production increased 163.7% and 6.6%, respectively (Table 2). It is estimated that copper production will be in the order of 2.3 Mt (2.5 million st) by 1996, when new projects now under construction come onstream. Gold production could reach 35 t (1.1 million oz) and coal production could increase another 1 Mt/a (1.1 million stpy). Open-pit mining has played a significant role in Chile’s minerals production growth. The expected increases in mine operations will come about mainly through new open pits or expansions of existing surface operations (Table 3). However, the number of open-pit copper mines will decrease from 74% to 66% of the total number of Chilean mines. Gold mines will increase from 63% to 69% of the total, while coal mines will go from 41% to 59%. Most all of the present iron ore production is from surface mines and will continue that way.

Jan 1, 1992

By G. Tapia, R. J. Kelley

Empresa Minera de Mantos Blancos S.A. successfully commissioned two copper SX-EW plants in late 1995. The design of these solvent extraction plants is such that chloride tenors of 30-35 g/l can be tolerated in the leach solution with no contamination of the electrolyte. The design was carried out in conjunction with Bechtel-ARA engineers and was based on the successful application of the available technology in the market; this mainly focused on decreasing the aqueous entrainment in the organic phase. This entrainment can reach 20,000 ppm in conventional plants.

Jan 1, 1998

By G. E. McCormack

The Development of Water Gel Explosives Water gels are the most recent development in the evolution of commercial explosives. They are replacing dynamite, having proven themselves to be excellent alternatives to this standard explosive. Water gels have steadily displaced dynamite over the past two decades. In 1959, they accounted for only 1 percent of the market they share with dynamite. By 1965, the share taken by water gels had grown to 21 percent. In 1970, it was more than 40 percent, and today it is nearly 70 percent. Black powder, the first widely used explosive, revolutionized mining and quarrying in its day. However, when nitroglycerin dynamite became available about a century ago, it rapidly displaced black powder because it provided greater energy for a given weight, much higher velocity for better rock shattering performance, and water resistance for easy use in wet conditions. During the past 50 years, ammonium nitrate has played a dramatically increasing role in explosives. First, it was used as an ingredient in dynamite, and then as the main component in nitrocarbonitrate blasting agents. About a quarter of a century ago, it began to find use in a simple and inexpensive mixture with fuel oil that has revolutionized the explosives industry and today fills about 80 percent of the requirements for explosives in the U.S., and certainly the bulk of blasting requirements worldwide. Water gels and dynamites share the remaining 20 percent. Water gel explosives based on ammonium nitrate have also been developed during the past quarter century. These explosives contain

Jan 1, 1979

By Robert D. Deister

The Buick Concentrator represents state-of- the-art technology in automated digital process control operation utilizing a centralized computer. The process control strategies implemented at Buick are no longer new to the industry but the successful application of these developments is still rather unique in North America. Productivity improvements, determined to be a direct result of the process control developments, are the primary topics of this paper. Emphasis is placed on metallurgical benefits including both lead and zinc recoveries, lead concentrate grade and reductions realized in reagent consumptions, operating costs and personnel. The productivity improvement discussion is preceded by a concentrator description and a brief history of the process control development at Buick. Current control strategies and future applications are presented afterward.

Jan 1, 1985

By Miguel Reyes, Bruce Whisner, Joseph Bickson, Lincan Yan, David Yantek, Justin Srednicki, Nicholas Damiano, Eric Bauer

Built-in-place (BIP) refuge alternatives (RAs) are designed to provide a secure space for miners who cannot escape during a mine emergency. Heat and humidity buildup within RAs may expose miners to physiological hazards such as heat stress. To minimize the risk of heat stress, Title 30 Code of Federal Regulations (CFR), or 30 CFR, mandates a maximum allowable apparent temperature (AT) for an occupied RA of 35 °C (95 °F) (MSHA 2008 [1]). The National Institute for Occupational Safety and Health (NIOSH) has conducted extensive research on the thermal environment of occupied RAs intended for use in underground coal mines. NIOSH research has demonstrated that a fully occupied BIP RA can exceed the AT limit by > 5.6 °C (10 °F) in mines with elevated mine strata and air temperatures (Bissert et al. 2017 [2]). In this circumstance, an RA cooling system could provide a solution. This paper provides an overview of test methodology and findings as well as guidance on improving the performance of a cryogenic air system prototype by optimizing the flow rate, increasing the tank storage capacity, and improving the efficiency of the heat exchanger of the cryogenic system. This may enable BIP RAs to meet the 35 °C (95 °F) AT limit in mines with elevated temperatures. The information in this paper is useful for RA manufacturers and mines that may choose to implement a cryogenic air system as a heat mitigation strategy

By Miguel Reyes, Bruce Whisner, Joseph Bickson, Lincan Yan, David Yantek, Justin Srednicki, Nicholas Damiano, Eric Bauer

Built-in-place (BIP) refuge alternatives (RAs) are designed to provide a secure space for miners who cannot escape during a mine emergency. Heat and humidity buildup within RAs may expose miners to physiological hazards such as heat stress. To minimize the risk of heat stress, Title 30 Code of Federal Regulations (CFR), or 30 CFR, mandates a maximum allowable apparent temperature (AT) for an occupied RA of 35 °C (95 °F) (MSHA 2008 [1]). The National Institute for Occupational Safety and Health (NIOSH) has conducted extensive research on the thermal environment of occupied RAs intended for use in underground coal mines. NIOSH research has demonstrated that a fully occupied BIP RA can exceed the AT limit by > 5.6 °C (10 °F) in mines with elevated mine strata and air temperatures (Bissert et al. 2017 [2]). In this circumstance, an RA cooling system could provide a solution. This paper provides an overview of test methodology and findings as well as guidance on improving the performance of a cryogenic air system prototype by optimizing the flow rate, increasing the tank storage capacity, and improving the efficiency of the heat exchanger of the cryogenic system. This may enable BIP RAs to meet the 35 °C (95 °F) AT limit in mines with elevated temperatures. The information in this paper is useful for RA manufacturers and mines that may choose to implement a cryogenic air system as a heat mitigation strategy

By Janice M. Zinck, W. F. Griffith

Four different high density sludge-type processes, Cominco HDS, Geco HDS, Tetra HDS Process and the Staged- neutralization process were studied for their effectiveness in treating a low strength Zn-Fe rich acidic drainage solution. Each proms was run continuously for at least two weeks after obtaining steady state conditions. The final effluent quality, lime consumption, sludge density, settleability, filterability, viscosity, neutralization potential, metal leachability, operating and capital costs were measured and evaluated for each process.

Jan 1, 2000

By Y. Luo, S. S. Peng

Several issues deserve further attention to improve subsidence prediction accuracy. These include: subsidence initiation and development over a setup entry area; subsidence development after face stop; and subsidence over chain pillar. An intensive subsidence monitoring program has been carried out over several longwall panels. A large amount of subsidence data has been collected, analyzed and solution techniques developed. In this paper, some of the measured data. data analysis techniques and the developed prediction methods are presented.

Jan 1, 1992

By Fathi Habashi

WHILE HYDROGEN SULFIDE precipitates metal sulfides from aqueous solutions, other gases such as sulfur dioxide, carbon monoxide, and hydrogen, under certain conditions, precipitate the metals directly. This can be achieved at high temperature and pressure. Such processes are of great technical importance, since metals of high purity are precipitated economically in a powder form. As a result of the availability of such powders on a large scale. processes for compacting metal sheet and other mill forms directly from the

Jan 1, 1970

This paper presents the results of an investigation of the stability of the mass flow rates and average pellet size in the different streams of an industrial-scale balling circuit. The variables in this study include water content, drum speed and fresh feed rate. It was found that both the mass flow rates and pellet diameter are greatly disturbed when a change, positive or negative, in any of the variables takes place. For most of these disturbances to be damped don, a period of one hour or so is required. When a disturbance in the feed rate was made, the transient period extended to more than one and half hours (the duration of the experiment). It was observed that there is an interaction between the drum speed and moisture needed for producing an acceptable green ball product. The moisture content of the product pellets was found to be a function of the pellet size, with the larger pellets retaining a higher moisture content.

Jan 1, 1980

By Leonid P. Ni, Askar M. Kunayev

It is well known that processing of the high-silicon bauxites for obtaining alumina by the hydrochemical Bayer process is irrational due to the significant losses of alumina and alkali with red mud. The main source of losses of the mentioned compounds under the conditions of leaching by the Bayer process is the formation of difficultly soluble sodium alumosilicate of the composition Na20 .Al203, 2Si02 . n H20. A conventional method of an extra recovery of alumina as well as of regeneration of alkali out of red mud is the high-temperature sintering of the latter with soda and limestone with the subsequent leaching of sodium aluminate from the sinter by water or soda solution. A sequential version of the Bayer-sintering flow chart recommended for the prosessing of bauxites with an increased content of silica is based on this method. However, the sintering method is not the only alkaline method allowing to make an extra recovery of alumina likewise of alkali from red mud. Our investigations showed/I/, that the components mentioned can be recovered by a pure hydrochemical method of treating red mud with concentrated alkaline solutions, with lime (Ca0) being present, that was earlier succesfully used in the development of the hydrochemical method of processing nepheline rocks/2/. The possibility of extracting alumina and alkali from red mud is based on the reactions which can be schematically represented in the following way:

Jan 1, 1984

By F. M. Doyle, Jun Li, Milton E. Wadsworth, Ximeng Zhu, E. Peters

The electrochemical behavior of pyrite in borate/sulfate solutions was investigated using cyclic voltammetry. Three anodic peaks at approximately -0.8 V, -0.1 V and +0.5 V (SCE) were detected along with their corresponding reduction peaks. The first two peaks correspond to the oxidation of surface products. The third peak corresponds to the direct oxidation of pyrite with reaction products FeO oxides. sulfate ion and partially oxidized sulfur intermediates present as a surface film of polysulfides and So. The Few oxides and sulfur intermediates were reduced to ferrous hydroxide and HS during the negative-going scan. The HS interacted preferentially with Fe(OH), on the surface to form FeS. Excess fenous hydroxide continued to reduce to metallic iron. During the return positive-going scan, metallic iron was oxidized to ferrous hydroxide and FeS was oxidized to pyrite. These reactions are characterized by a unique double peak observed in the region -0.8 to -0.65 V. The growth kinetics of the surface sulfur film formed during anodic oxidation were studied using chronoarnperomeay. Potentiostatic measurements were well correlated by a paralinear rate equation, suggesting the formation of an intermediate passive film, associated with the simultaneous dissolution of the outer layer of the film. The reaction rates were affected by applied potential, solution pH and temperature, but were independent of electrode rotation speed. A reaction kinetics model which fitted well with experimental results, was developed.

Jan 1, 1993

By Reul A. Dejú

The mineral olivine has been the subject of continued research by various authors. Paik (1967) conducted infrared and flotation studies of the adsorption of sodium alkyl benzene sulfonates on olivine. These studies are of interest from two points of view. First, in the metallurgical field it is of interest to understand the mechanism of silicate flotation using sulfonate collectors and second to a hydrologist studying the pollution of surface or subsurface waters it is of interest to study the reactions taking place when water plus sulfonates encounter a porous (silicate) medium. On the basis of Paik's study he was able to postulate a possible mechanism for the attachment of RSO3 (sulfonate radical) to the olivine surface. Parks (1969) has been studying the important influence of the structure of a silicate such as olivine on its dissolution mechanism and its related surface charge. Also Luce, a student of Parks (1964, 1965) has been studying the kinetics of dissolution of olivine using the techniques of direct solution analysis and infrared analysis. Certainly a classic in the study of silicate dissolution is the work of Murata (1940) on the reaction of orthosilicates (olivine in particular) with strong acid solutions. Many authors (Dejú and Bhappu, 1966. 1967. 1968, Dejú, 1969; Rhoades and Krueger. 1968, and Faust and blunter, 1967) have reported studies of the behavior of silicates immersed in water (especially orthosilicates) and have found that there is an exchange of cations from the silicate surface for H+ from the water. Studies by Dejú and Bhappu have also included the system olivine-water-amine.

Jan 1, 1971

By H. Verakis

A fire in a coal mine conveyor belt entry represent a major safety and health risk to miners. Fighting belt entry fires can be a commanding effort. If there is a failure of one aspect in the fire fighting needs such as a dissimilar hose-valve connection, then it can result in the inability to extinguish a fire. Fire incident data compiled over nearly 30 years for underground coal mines shows that fires in belt entries account for 15-20 percent of the total number of fires. Fires in the belt entries of coal mines have resulted in injuries and fatalities. New regulations have been promulgated that require an unplanned fire not extinguished within 10 minutes of discovery to be reported to the Mine Safety and Health Administration (MSHA). A fire that is not extinguished within several minutes may take hours or days to extinguish or may require sealing a section or the mine in some cases. The current fire protection regulations in the U.S. Code of Federal Regulations (CFR), Title 30, Part 75 are designed to prevent or control the fire hazards present in a belt entry. These requirements and other factors affecting belt entry fires are discussed, including fire detection and warning, fire suppression devices, type and location of fire fighting equipment, waterlines, and cleanup and removal of combustible materials. The fire suppression systems used to extinguish/control a belt fire and the effect of ventilation on the propagation of conveyor belt fires are also discussed.

Jan 1, 2009

By Joseph C. Rota, Charles E. Ekburg

Introduction The Gold Quarry gold deposit is the largest bulk tonnage epithermal gold deposit in northeastern Nevada to be developed by Newmont Gold Co., formerly known as Carlin Gold Mining Co. Exploration and development of the deposit extended over a period of nearly 50 years before bulk tonnage mining became economically feasible. Proven reserves at Gold Quarry are currently estimated at more than 255 t (8.2 million oz.) of gold, accounting for more than 40% of the total Carlin Trend mineable reserves for 1986. Milling began in late 1985; dump leaching of lower grade ores began in May of 1986. The mill has exceeded the initial design throughput rate of 6.3 kt/d (7000 stpd) and is now processing more than 8 kt/d (9000 stpd). The dump leach facility will process more than 7.3 Mt (8.1 million st) of lower grade ores in 1986. The Gold Quarry ore body is to be developed by an open pit that will eventually be 1830 m (6000 ft) long, 1220 m (4000 ft) wide and 300 m (1000 ft) deep. The mine currently produces 77 kt/d (85,000 stpd) on a 24-hour-a-day, seven-day workweek. Planned pit production will increase to nearly 168 kt/d (185,000 stpd) in 1988. Production equipment currently includes one Demag H-/285, three Komatsu PC-1500 hydraulic shovels, two Cat 992C loaders and 21 90 to 135 t (100 to 150 st) haul trucks. Mining is conducted on 8 m (20 ft) benches within the Paleozoic

Jan 4, 1988

By Brian Gettinger, Jim Schlaman, Alston Noronha

"INTRODUCTION The public understanding of green solutions today is based on the definition of sustainability adopted by the Brundtland Commission (World Commission on Environment and Development) in 1987: “development that meets the needs of the present without compromising the ability of future generations to meet their own needs.” Over time this initial definition evolved to identify three distinct factors impacting sustainability that are often referred to as the “Triple Bottom Line”: Economic, Environmental and Social. The triple bottom line approach seeks to drive outcomes that create maximum value for all stakeholders. In the last ten years purveyors of water and wastewater tunnel solutions have found themselves on the wrong side of a politically polarizing issue in the crosshairs of politicians, environmental activists and community groups branding tunnels as expensive, “gray” and not-sustainable. Tunnels under design were stopped and large planned tunnel programs were delayed or canceled. Therefore being sustainable and “green” is not simply using natural vegetation, but creating an asset that meets current and future needs and will not become a future liability. As this paper will discuss, tunnel projects embody a sustainable triple bottom line project well, are equally sustainable as green infrastructure, and have begun to gain awareness for their sustainability. GREEN INFRASTRUCTURE CHANGES TUNNELING LANDSCAPE The green movement quickly swept across the nation in the mid to late 2000’s and was a hot topic in the media and at all the local, regional and national industry conferences. Politicians espoused the benefit of green infrastructure including job creation, urban renewal, aesthetics, property values economics and sustainability. The political microscope was focused the closest on stormwater and wastewater management, particularly in communities responding to combined sewer overflow (CSO) consent decrees from the Environmental Protection Agency (EPA). As communities with CSO problems evaluated their long term control program (LTCP), local government officials and planners began to balk at the huge price tag required for compliance and began looking for alternatives. “Green” infrastructure was proposed as lower cost solution that could be used to offset capital-intensive “gray” infrastructure like new sewers, storage tanks, tunnels, and treatment facilities. In addition, including green infrastructure in a previously negotiated LTCP required a reset on the entire planning process, additional studies and more planning which would push capital investment further off into the future, subsequently delaying unpopular user rate increases. As a result, tunnel projects as well as trenched conveyance and treatment plant projects that had not yet started construction were stopped, delayed or substantially changed."

Jan 1, 2016

By Peter W. Willcocks

The Cyanide Regeneration Process (CRP) was developed by Golconda Engineering and Mining Services and installed at Golconda's Beaconsfield Gold Tailings Retreatment Project situated in Tasmania, Australia. The Tailings Project is a 1000 ton per day carbon-in-pulp treatment plant, feed for which consists of tailings material which is dredged from the Tamar River. The pulp is screened to remove debris, then cycloned to form two products. Underflow pulp is stored in a 350 ton bin and cyclone overflow passes to a thickener. The coarse pulp material is fed to the grinding circuit then rejoins the thickened slimes in the cyanide leach circuit. Gold is extracted by carbon-in-pulp techniques. The plant is sited in rolling, hilly country approximately 200 meters from the Tamar River. The residue disposal area is quite small consisting of four dams, totalling 42 acres. The regional climate is cool and wet with little evaporation; therefore, we anticipated a net increase in contained liquor, and subsequent storage problems. Our plan was to remove cyanide from the liquor prior to returning the detoxified solution to the river system. Such treatment was not required until midway through the second year of the project. Initial testwork on sample material indicated that destruction of cyanide by chlorine was the simple solution. Subsequent follow-up on actual plant liquor indicated a huge chlorine requirement due, we believe, to the substantial degradation of vegetable matter plus organic content from the marine environment. The cost of cyanide destruction could not be justified.

Jan 1, 1998

By D. Robert Weir

The pioneers in pressure hydrometallurgy have provided a solid foundation during the past four decades. The pressure techniques are now capable of being used to push back the frontiers in the winning of metals. Pressure hydrometallurgy has been used to meet the objectives of extracting metals; purifying metal solutions, recovering metals; and rendering waste streams acceptable for disposal to waste repositories and the environment. Some examples of each of these functions are briefly reviewed. The applicability of pressure techniques to the recovery of precious metals is discussed.

Jan 1, 1985