Search Documents

By Ehsan Alavi, Glen Frank, Michael DiPonio, Mike Mooney, Lisa Mori

"A study was conducted on the N125 project in Seattle to investigate the use of apparent density as an assessment tool for the effectiveness of soil conditioning. The formation of an air bubble as well as the plugging of cutterhead and excavation chamber can be a result of improper soil conditioning. Both air bubble formation at the top of the excavation chamber and developing plugging issues can be identified by analyzing the apparent densities in the excavation chamber. In this study, apparent densities less than unity were observed in the upper portion of both northbound and southbound TBMs, suggesting the presence of an air bubble. Apparent densities greater than the in-situ soil density were observed in the lower portion of the excavation chamber. Particularly high values of apparent density were coincident with clogging observed at multiple locations along the alignment. The combination of less than unity upper chamber apparent density and very high apparent density in the lower portion of the chamber are related, and indicate the inability of the TBM to effectively condition and mix the soil in the chamber.INTRODUCTIONProper soil conditioning in EPB tunneling offers many advantages to the quality and productivity of the project. There are few operational parameters that can be used to assess the soil conditioning performance such as advance rate, torque, thrust, chamber pressure signature, etc. One of the other parameters that potentially can be used is the apparent density. The apparent density of the material in the chamber was introduced by Guglielmetti et al. (2003) as the vertical chamber pressure gradient calculated from the physical relation between the horizontally measured chamber pressures and the vertical distance between the pressure sensors. Guglielmetti et al. (2003) introduced apparent density as a measure to ensure the excavation chamber is filled with material. To guarantee face stability the authors suggest to keep the apparent density over a certain limit so the material is able to transfer effective stress to the virgin soil, and thus provide support of the excavation face. They implemented this method at the Metro project in Porto, Portugal.Comparing the vertical gradient of the horizontal chamber pressures to the densities of excavation chamber samples, Bezuijen et al. (2005) discovered that the gradient is not necessarily representative of the muck density. They assumed that the yield stress of the muck as well as the adhesion between the muck and the cutterhead and bulkhead material have an influence on the vertical gradient during mining (Bezuijen et al. 2005, Bezuijen & Talmon 2014)."

Jan 1, 2016

By H. G. Stephenson, D. Castendyk

Open pit anthracite mining at the Canmore Creek Mines, Canmore, Alberta, south of Banff National Park, resulted in several pit lakes by the early 1970’s. To enable future mining opportunities in the Rocky Mountains, operators decided to reclaim the site into a non-polluting landscape which would provide a memorable outdoor experience for residents and visitors alike, and would preserve wildlife habitat. Reclamation began with the stabilization and revegetation of spoil piles adjacent to Canmore Creek, and the backfilling and revegetation of Canmore Creek Mines No. 1 and 2 to create “Salamander Pond.” The company dammed the outlet of an open pit at Canmore Creek Mine No. 3 to raise the water level and create Quarry Lake. Reclamation concluded in 1980 when the Town of Canmore took ownership. Quarry Lake is now the centerpiece of 293-acre Quarry Lake Heritage Park, a popular destination for swimming, hiking, and fishing, visited by about 400 people on summer days. The Alberta Environment Conservation Authority described this as “The best mine reclamation in Western Canada.” Quarry Lake is an exceptional example of walk-away, pit lake closure, where the mining company created a valued post-mining asset and was released from future liabilities. INTRODUCTION One of the most important environmental issues associated with contemporary open pit mining is the closure of mine pit lakes, and the perpetual legacy these lakes can potentially generate. Ideally, successful pit lake closure includes the following: (i) the water quality within the pit lake, plus surface water and groundwater discharging from the pit lake, meets pre-mining, or other acceptable water quality conditions of the receiving environment, (ii) the termination of all active treatment processes, (iii) the return of the pit lake to the government for long-term care and maintenance, (iv) the release of the mining company from all future liabilities associated with the pit lake, (v) the return the environmental bond to the mining company, and (vi) the reuse of the pit lake for some post-closure, beneficial purpose. The achievement of these goals is known as “walk away, pit lake closure.” Peer-reviewed, publications of successful walk away, pit lake closure provide mining companies the ability to address public concerns regarding the safety of pit lakes which commonly occur during the permitting, operations, and closure phases of mining. To date, most published work on walk away, pit lake closure work has occurred in the coal mining sector in Germany and Australia (McCullough et al., 2009; Jones and McCullough, 2011; Kumar et al., 2013; Schultz et al., 2013). However, in North America, examples of walk away, pit lake closure are not widely discussed in the literature despite there being excellent examples from the coal mining sector in Alberta, Canada (e.g. Pleasure Island, Black Diamond, East Pit, Sphynx, Robb, Lovette, Siltstone, and Sterling), and from the iron mining sector in Minnesota in the United States (e.g. Portsmouth Lake, see MNDNR, 2018). Although seldom included in discussions of pit lakes from the metal and coal mining sectors, the aggregate and fabricated-stone mining sectors also produce pit lakes, and there are numerous examples throughout North America where these pit lakes have been successfully closed and transformed into post-mining resources. The difficulty of finding these good examples in the literature makes it challenging for companies to respond to public and regulatory questions regarding pit lake closure and reuse. As such, there is a pressing need document the motivations and approaches used in examples of successful, walk away, pit lake closure in North America so that the mining industry at large can learn from these examples and can better address public concerns.

Jan 1, 2019

By J. G. Mansanti

The metallurgical response of a deposit's various ore types usually has a strong impact on the flowsheet design of most mineral processing plants. This impacts the materials handling, equipment selection, capital and operating costs, and plant availability. Because of the rapid leaching characteristics of Chimney Creek ores a variation of the conventional gold plant, carbon columns and CIP was proposed. The proposal consisted of a washing stage which was installed between the typical leaching and CIP stages. The circuit was simulated in the lab and was modelled using a computer program to evaluate the metallurgical impact and the effect on the system's mass balances. Also, actual plant data was reviewed comparing the results that were achieved with the results that were expected.

Jan 1, 1988

By W. C. Morgan

Recently passed federal strip mining legislation officially emphasizes that the increased coal production required by this country through surface mining is going to be obtained only with stricter environmental standards. Dozing overburden down the hillside in Appalachian contour mining or leaving drag1ine spoils in area mining is now taboo and it is now or will soon be necessary to return the disturbed land to as good or better condition than before mining. These new restrictions will create a need for new and better ways to do the job. This paper describes one approach for utilizing scrapers and dozers to strip all of the overburden and to replace that overburden in an environmentally satisfactory fashion. The objective was to do this at a lower cost than that possible with the traditional dragline system using dozers and scrapers for reclamation and topsoil handling. In area stripping, the dragline has been able to move overburden at an extremely low cost. Operating costs of 8-13¢/bcy are typical in many operations where rehandling is not required. However, the cost of leveling the spoil piles and rehandling topsoil add considerably to the low basic cost of drag1ine stripping.

Jan 1, 1977

By Ihsan Berk Tulu, Mustafa Can Suner

The synthetic rock mass (SRM) approach is a relatively new method to study the mechanical behavior of rock masses. Recently, an SRM approach was established to estimate pillar strength from laboratory scale to in-situ dimension using the two-dimensional Universal Distinct Element Code (UDEC). In this study, the developed methodology is applied to the S-Pillar database to estimate pillar strength and failure mechanisms as a function of width-to-height ratio of the pillars. First, stone mine rocks are categorized into three as low-, medium-, and high-strength according to their uniaxial compressive strength (UCS). Later, laboratory-scale intact rocks are scaled-up to the average in-situ pillar dimensions by explicitly considering the naturally existing joint sets. It is found that the strength of the pillars with low-UCS are overestimated when compared to pillars with high-UCS. This observation is attributed to the high joint density of the pillars with high-UCS. After obtaining in-situ pillar strength, the width-to-height ratios of the pillar models varied from 0.5 to 2.0 to gain a robust understanding of pillar mechanical behavior. Tensile failure is found to govern the pillar behavior with the width-to-height ratio of 0.5 while the combination of tensile failure in rib elements and shear failure in the core

By A. Adu-Acheampong

A geotechnical study was conducted to identify the cause(s) of stope instability at the Ashanti Mine (Obuasi, Ghana). As part of the investigation, laboratory testing of rock was performed and the rock mass was classified according to the Q-System (Barton et al., 1974).Numerical analyses were performed using the computer program FLAC (Itasca, 2001). The observed failure zone around the stopes was simulated using both Mohr-Coulomb and Hoek-Brown (Sheorey,1997) models. Yielding along peripheral graphite bands and tensile failure were clearly identified to be the major contributors to stope instability.

Jan 1, 2003

By G. B. Glass

In 1996, 92.5% or 233 Mt (257.4 million st) of coal produced in Wyoming came from the Wyodak coal zone in the eastern Powder River Coal Field. While the mined portions of the zone consist of one to three beds of coal with an aggregate thickness between 15 and 33.5 m (50 and 110 ft), the thickest expression is 61 m (200 ft). The delivered coal from this zone averages 0.33% sulfur, 5.12% ash, and 19.98 MJ/kg (8,590 Btu/lb). This coal zone occurs at or near the top of the Paleocene Fort Union Formation, which is overlain by the Eocene Wasatch Formation. There is also production from two coal beds in the lower portion of the Wasatch at the southern end of the basin. Production of coalbed methane derived from the Wyodak coal zone is currently an estimated 10.2 billion cu ft a year. This production is occurring just west and downdip from the coal mines and is increasing each year.

Jan 1, 1998

By Christina Dahnér, Kristina Jonsson, Savka Dineva

The iron-ore underground Kiirunavaara mine (Sweden) has been seismically active since 2008. In 2021 the production is on levels 1079 and 1108 m, at the deepest. The seismic activity has changed in character over time with one step change in 2015 when the number of large (ML>2) seismic events increased, and another one when the mine experienced a seismic event with Mw 4.2 in 2020. In 2017, the mine evaluated Hydraulic Fracturing (HF) as a possible mitigation technique for larger seismic events and a one-hole trial was performed. The trial proved promising, and it was decided to go forward with a large-scale trial covering an entire production area in the mine. The large-scale trial consists of 25 fracturing holes, 50 – 100 m long, running along 500 m out of the ~4500 m long orebody and spanning between production levels 1108 m and 1252 m. The fracturing process continued for a year, resulting in ~38,000 seismic events with −3.3<ML<1.4. The breakdown pressure varied between fractures in the same hole as well as between holes in the same area. Average breakdown pressure per hole was between 12 MPa and 50 MPa. The seismic response to HF in 2021 varied greatly from hole to hole and between fractures in the same hole. The variation in response could be related to the geological conditions and the infrastructure, such as large caving ore passes. In this paper some details about the experiments and broad preliminary analysis of the effect of the HF by using seismic source parameters of the induced seismic events are presented: 1) Distribution of seismic activity, 2) the ‘equivalent’ magnitudes for each hole calculated from the cumulative seismic energy and seismic potency released during the fracturing, compared with the local geological conditions; 3) the predominant failure mechanism of the seismic events caused by HF was defined. A difference in the behaviour between larger and smaller events was noticed, as ML>0 events seem to be compression type failures and ML<0 events seem to be related to slip on pre-existing structures. No seismic events related to creation of a new fracture have been identified yet.

Apr 26, 2022

By Thomas E. McNider

Preliminary studies were conducted at Jim Walter Resources, Inc. Blue Creek No. 3 Mine to determine the influence propane operated heaters exert on the mine ventilation system when two of three intake airshafts were heated. During initial use of the heaters, it was found that change in density caused by heating a portion of the air at two of three intake shafts altered under- ground air flow changes sufficient to be considered a violation of Part 75.322 of the Federal Coal Mine Health and Safety Act of 1969 as amended by Public Law 95.164. The primary concern was to accurately define the problem in order to derive a workable solution.

Jan 1, 1980

By P. Bissert, M. Klein, L. Yan, D. Yantek

"Mine Safety and Health Administration (MSHA) regulations require underground coal mines to use refuge alternatives (RAs) to provide a breathable air environment for 96 hrs. One of the main concerns with the use of mobile RAs is the heat and humidity buildup inside an RA. The accumulation of heat and humidity can result in miners suffering heat stress or even death. MSHA regulations require that the apparent temperature in a fully occupied RA must not exceed 95°F. To investigate this issue, the National Institute for Occupational Safety and Health (NIOSH) conducted testing on a 23-person tent-type RA in its Experimental Mine (EM) in a test area that was isolated from the mine ventilation system. The test results showed that the average measured air temperature within the RA increased by 9.4°C (17°F) and the relative humidity (RH) approached 94 %RH. The test results were used to benchmark a thermal simulation model of the tested RA. The validated thermal simulation model predicted the average air temperature inside the RA at the end of 96 hours to within 0.6°C (1.0°F) of the average measured air temperature. INTRODUCTION If an accident occurs in an underground coal mine, miners who fail to escape from the mine can enter an RA for protection from adverse conditions, such as high carbon monoxide levels. One of the main concerns with the use of mobile RAs is the potentially adverse thermal environment inside an RA from the metabolic heat of the occupants and the heat released by the carbon dioxide (CO2) scrubbing system. Moreover, the humidity within the RA will increase through occupants’ respiration and perspiration and from the chemical reaction within the CO2 scrubbing system. The accumulation of heat and humidity can result in miners suffering heat stress, heat stroke, or even death. In its 2007 report to Congress, the National Institute for Occupational Safety and Health (NIOSH) Office of Mine Safety and Health Research (OMSHR) recommended that RAs should be designed to ensure that the internal apparent temperature (a temperature-humidity metric) in an occupied RA does not exceed 35°C (95°F). However, a standard method to determine compliance with this metric does not exist. The heat transfer process within and surrounding an RA is very complex, and is not easily defined analytically or experimentally. To investigate the related issues, OMSHR conducted heat and humidity testing on a 23-person tent-type RA in its Experimental Mine (EM) in a test area that was isolated from the mine ventilation system. During the testing, numerous parameters were measured: heat input to the chamber, the air temperature and relative humidity inside the RA, the air temperature in the mine, the mine strata temperatures versus depth, and the airflow inside and outside the chamber. The focus of this paper is on the temperature rise within an RA. TAITherm heat transfer analysis software was used to develop a thermal simulation model of the RA as it was tested in the mine, using the test results as the benchmark. Both sensible and latent heat were used in the test and the model."

Jan 1, 2016

By M. E. Kuchta

LKAB&apos;s Kiruna mine, located above the Arctic Circle in northern Sweden, is one of the world&apos;s largest underground mines, and it is one of the most modern. The Kiruna orebody is a high-grade magnetite containing about 80% low-phosphorous iron ore and about 20% high-phosphorous iron ore in situ. The mining method used is large-scale sublevel caving. Due to the blending of high-phosphorous ore with low-phosphorous ore during the extraction process, only about 20% of the run-of-mine ore can be used for the mine&apos;s low-phosphorous product. The blending process is highly irregular and difficult for the mine-planning personnel to predict. An algorithm was developed that uses principles of gravity flow to predict the run-of-mine phosphorous grades from the in situ geologic block model. The model can be used for both long- and short-term predictions.

Jan 1, 2003

By Barry J. Hansen

Mining can make two major contributions to the cleanup of the environment. The first of these is the extractive technology that has become highly developed as a result of centuries of development. Of equal impor­tance are the methodology of analysis and the development of engineering solutions that are the stock in trade of the mining industry. Despite the differences between the industries, the processes for the development of a mine and the cleanup of a hazardous waste site are similar. The characteristics that impact the ability to develop a suitable process for treating an ore body or correct­ing an environmental problem are those relat­ed to the distribution of the contaminant or metal in the host material.

Jan 1, 1991

By Shawn Orser, Jennifer Waddell, Mike Sierakowski, Tom Barrett

Production evaluations were conducted at Daisy Gold Mine (Glamis Gold, formerly Rayrock), between August, 1997 and August, 1998 to quantify the effect of 3M fluorochemical surfactants (fluorosurfactants) on extraction kinetics and gold recovery in gold heap leach mining operations. Ore was treated at a level of 7-10 grams surfactant per ton of ore using 3M Pluorad TM Leach Mining Additive PC-GOLD. Kinetics and gold recovery were determined by solution assay for each of the tests. Both tests indicated improved kinetics, and data from Test 2 was used for determination of a quantitative increase in gold recovery resulting from PC-GOLD addition. A discussion of test results including methods used to determine gold recovery is provided.

Jan 1, 2000

By Randall D. Peterson

Economic operation of a mine ventilation system must include some means by which operating costs can be quantified and evaluated periodically. Current practice at most mines relies upon the best judgement of foremen, engineers and managers to identify high cost or problem areas in the system and to estimate potential costs and benefits of work proposed to reduce inefficiencies. The problem with this is that significant savings can be overlooked or sub-economic projects may be undertaken when sufficient attention is not paid to the interrelationship between airflow characteristics and corporate financial criteria. In order to accurately determine costs and benefits it is necessary to view the solution of each potential ventilation problem as a separate economic opportunity.

Jan 1, 1993

By Muhammad O. Rahim

The importance of planning ventilation systems in modern coal mines cannot be overemphasized. Interconnected entries, airflows around and through mined-out areas, leakages through stoppings and other control devices, and the use of multiple fans all contribute to the complexity of ventilation network analysis. Fortunately, the availability of computer programs (e. g., Didyk et al., 1978; McPherson, 1966; Wang and Saperstein, 1970) has greatly reduced the difficulty in net- work analysis. However, to obtain a suitable solution to the practical problem, a ventilation engineer has to simulate various conditions based on the proposed ventilation layouts and the capacities of available fans. It is often a trial-and-error process, although engineering knowledge and judgement are required.

Jan 1, 1982

By Milka Madahana, John Ekoru

For efficient management of operations, mining companies are required to be able to predict potential scenarios for main market factors. Competitive advantage and value creation are established through managing the value chain well. The mining value chain is usually faced with challenges from various shifts in commodity markets as well as ongoing uncertainties. Therefore, there is a need for accurate analysis of data from the markets, for the prediction of commodities, for instance, Precious Group Metals (PGM). The main objective of this research work is to apply machine learning methodologies with the aim to identify patterns and trends in the Precious Group Metals, and thereafter analyze and predict the future trends of these markets. Numerous machine learning models are applied to a dataset consisting of 15 years of daily price for eight precious metals namely Platinum, Palladium, Rhodium, Ruthenium, Osmium, Indium, Silver, and Gold. The results reveal the patterns and trends within the data sets and that different machine learning methods could be suited for the prediction of market prices for each of the PGMs. The application of an amalgamation of various machine learning methods may result in more accurate predictions of the PGM markets. Accurate prediction of market prices for PGMs will possibly result in unlocking untapped sources of value in the mining industry.

Jun 25, 2023

By Richard E. Steffens

The underground portion of Duke Power Company&apos;s Bad Creek Pumped Storage Project in northwestern South Carolina consists of a powerhouse cavern (132 m. long, 23 m. wide, 50 m. high), 407 meters of shafts and approximately 3615 meters of tunnel, both lined and unlined, with diameters varying from 4.2 meters to 9.0 meters. A case history is presented, including the early pilot tunnel exploratory work and how this affected design, the design of the project, and the excavation, rock support and tunnel lining work. Problems and experiences encountered during the construction are given. The effects of high horizontal insitu stresses in the granitic gneiss are discussed along with solution taken.

Jan 1, 1989

By P. Mousset-Jones, F. Calizaya

This paper explains and discusses a computer program that has been developed to determine the ventilation design parameters for complex auxiliary ventilation systems such as those found in the construction of long excavations with multiple headings. The program is based on the principle of partitioning the system into segments of finite length, and formulating and solving the resulting networks recursively. The resulting network problems are solved analytically. With this program, the size of fans can be determined in order to reduce the total leakage and minimize the flow recirculation. The application of the program is illustrated by the detailed solution of an auxiliary ventilation system proposed for the Exploratory Studies Facility (ESF) at the Yucca Mountain Project, Nevada.

Jan 1, 1995

By Yiming Sun, David Tsztoo, Rick Nolting, Adam M. Wirthlin, Rebecca Fusee

"Excavation and initial support of the New Irvington Tunnel presented significant challenges, including rapidly changing ground conditions, heavy ground loads, and squeezing. Such behaviors were anticipated from historic tunneling records of the adjacent Existing Irvington Tunnel, and extensive site investigation, but clearer understanding of their actual extent and causes has resulted from convergence measurements, observations of ground behavior, initial support monitoring and detailed geologic mapping. Time-dependent movements, documented hours to months after excavation in clay-rich rock and in moderately to intensely fractured rock, identified squeezing areas, allowed classification by currently-used predictive methods and added to the list of lessons learned in tunneling such ground. INTRODUCTION In March 2003 the San Francisco Public Utilities Commission (SFPUC) authorized funding for the $4.6 billion Water System Improvement Program (WSIP) to repair, replace, and seismically upgrade its water system. The program consists of 35 local projects located within San Francisco and 48 regional projects located in several counties from the Sierra foothills to the San Francisco Bay Area. The New Irvington Tunnel (NIT), a key component of the WSIP, is located east of Fremont in Alameda County, on the east side of San Francisco Bay. The NIT is a new 18,660 foot (5,689 m), redundant tunnel, 190 to 670 feet (58–204 m) offset from, and subparallel to the Existing Irvington Tunnel (EIT). Built between 1928 and 1932, the EIT was constructed with an unreinforced cast-in-place concrete lining and is vulnerable to damage in the event of a major earthquake along the two closest active faults. The Hayward Fault is located less than a mile west of the tunnel, and the Calaveras Fault is located half a mile east of the tunnel. Although the alignment does not intersect these faults, the shaking and sympathetic displacement along secondary faults that cross the tunnel alignment are potential hazards. The NIT provides a seismically reliable water transmission facility capable of withstanding earthquake damage and maintaining continuous water service after a major earthquake. The NIT also adds system redundancy and provides for operation flexibility of running water through both tunnels, or through one tunnel while the other is out of service for inspections and maintenance."

Jan 1, 2016

By J. O. Marsden

The Candelaria copper-gold mine is located approximately 25 km south and east of Copiapo in Region III, Chile. The original concentrator was designed to treat 28,000 t/d (30,800 stpd) of chalcopyrite-bearing ore through a circuit consisting of a single 11.0 m (36 ft) diameter SAG mill, two ball mills, conventional rougher and scavenger flotation, column cell cleaner flotation, and ceramic disc filtration. The plant was commissioned in August 1994 and quickly reached capacity and expected levels of metallurgical performance. In May 1996, a decision was made to double the capacity of the concentrator by the addition of a second line of equipment. The expanded facilities were commissioned in October 1997, less than 18 months after the decision to proceed, and well within the budget. The original concentrator facilities were replicated or duplicated as much as possible, however, a number of important equipment changes were made to take advantage of industry developments since the original concentrator was designed. These included the use of Eimco 120 m3 (4,200 ft3) cells for rougher and scavenger flotation and the installation of a Svedala VTM -800 Vertimill for regrinding. This paper describes the rationale behind these changes and explores the reasons for the success of the project.

Jan 1, 1999