Search Documents

By J. Pereyra, M. DeMarco

"INTRODUCTION It can be vital that bolted joints holding subassemblies together remain secure. Bolts should resist the loosening effects of vibrations and dynamic loads yet need to be easily removable during maintenance. When a threaded fastener is subjected to vibration, the rapid movement causes a lowering of friction against the threads and a subsequent loss of preload. The loss of preload allows the fastener to vibrate loose and possibly fall out. As the diameter of fasteners increase desired preload becomes increasingly more difficult to achieve. Input torque requirements for achieving proper bolt preload is exponentially related to any given fasteners diameter. This means that specialized tooling or bolting practices are usually required to attempt the tightening of fasteners to reach their required preload. Traditional methods can cause problems with joint integrity and do not provide consistent bolt load across the bolted surface. BOLTED CONNECTIONS A failed critical bolted joint can lead to high maintenance costs, machine downtime, and risk to worker safety. Control of the clamp load in a bolted joint is vital. However, when faced with a problem joint, it is not surprising that the design engineer will not have an answer if asked about the clamp load. Torque calculations must always be based on the existing conditions that often are vague. Unless all parameters are correct, the calculation will be unreliable. Examples of parameters are: • Thread condition of the fasteners • Hardness of contact surface • Material (steel, aluminium, copper, etc.) • Extra friction from a locking fastener • Extra friction from an adhesive • Lubricant on the thread • Type of bolt head (flanged, regular or serrated) • Surface coating of the bolt • New or reused fastener During tightening, bolts are subjected to both tensile and torsional stress. The total stress in a bolt can be calculated using the formula: Total stress = vsx2 + 3txy2 In order to maximize the desired tensile stress (sx) it is vital to minimize the torsional stress (txy). Tensile stress (clamp load) is achieved when the bolt is axially elongated. Unwanted torsional stress (twisting) in bolts arises during tightening due to thread friction. High thread friction increases torsional stress and causes yielding at lower clamp load levels than normal. A lubricant is necessary to minimize the malign torsional stress. However, many commonly used bolt-locking systems are based on increased thread friction (deformed nuts, adhesives, etc). To minimize thread friction and concurrently safely secure the joint has often incorrectly been considered impossible. The use of locking systems that increase thread friction is the single most common reason why the full capacity of bolted joints is not utilized. The following example illustrates the problem."

Jan 1, 2015

By Miguel Angel Ibarra

This paper describes the results of a digital computer simulation study in which the impact of the proposed truck dispatching on the overall mine productivity was investigated for an operating open pit mine. In the study, the existing operation was first simulated for a one-month period, using both the actual time study data and the computed cycle times. By adjusting certain input parameters to the simulation program, the actual one month production was first duplicated through simulation. Afterwards, the operation was again simulated in a dispatch mode. Comparison of simulation results under the dispatch mode, with the initial base case simulation results, showed a definite improvement in overall productivity with dispatching; i.e., approximately 10% gain for the operation. As expected, the results also showed that the extent of possible improvement did vary with the particular pit configuration being investigated.

Jan 1, 1980

By Ruckmick J. C.

Elemental sulphur occurrences are widely distributed in two geological environments: -1-Basins containing hydrocarbons and zones of Cenozoic vulcanism. However, very few of these constitute deposits large enough to be of commercial importance. Almost all of the elemental sulphur mined in the world comes from bioepigenetic deposits in petroliferous basins. These deposits occur in two general structural styles: diapiric (salt domes) and stratiform. Examples of diapiric deposits occur in the Gulf Coast basins of Texas, Louisiana, and southern Mexico. Examples of stratiform deposits occur in the Fergana and Amudarya depressions of Central Asia, the Mesopotamian Depression in Iraq, the Cis-Carpathian Trough in Poland and Russia, and the Permian Basin in Texas. Economic bioepigenetic sulphur deposits range in size from approximately 1 million tons of sulphur in the smaller salt dome deposits to more than ZOO million tons of sulphur at the Mishraq stratiform deposit in Iraq. Total world production from bioepigenetic deposits amounts to approximately 16 million tons of sulphur per year, one-half of the world's present annual consumption of elemental sulphur. Most of the balance of the annual consumption is recovered from sour gas and petroleum. All bioepigenetic sulphur deposits share remarkably similar origins and characteristics. They are formed by anaerobic bacterial replacement of gypsum or anhydrite in tilted basins where evaporite beds are underlain by petroleum. Figure 1 illustrates a generalized cross-section of a salt dome sulphur deposit. Figures Z, 3, and 4 are cross-sections of three types of stratiform sulphur deposits. In terms of sulphur genesis, the only significant difference between the salt dome and stratiform deposits is that the positioning of the anhydrites above the petroleum in the salt domes is caused by diapiric rather than sedimentary processes. In the salt domes, the residual anhydrites of the cap-rocks are accumulated by solution and removal of halite by artesian ground waters.

Jan 1, 1978

By D. M. Muir

Thiosulfate offers a non-toxic alternative to cyanide for processing gold ores. The mechanism of leaching gold using ammoniacal thiosulfate solution is driven by the Cu(II)-Cu(I) redox couple and is complicated by competing ligands such as NH3 and S2O32-. It is shown that an understanding of the copper speciation and sulfur speciation is required to optimise this system. This paper presents Eh-pH and speciation diagrams for varying concentrations of Cu(II), S2O32- and NH3 and discusses the conditions under which various copper and sulfur species are stable.

Jan 1, 2001

By John V. Beall

The Mining Engineering Handbook is written primarily for persons interested in the economic extraction of minerals. Not everyone referring to this book will be knowledgeable about mining and, therefore, this section is intended to explain to interested persons the scope of mining as well as fulfilling the title of "Mining's Place and Contribution" among the industries of society. 1.1-MINERALS, ROCKS AND ORE In the year 1971, the number of known elements amounted to 104. Fifteen of these have been made only in the laboratory, others may have persisted from the primitive atmosphere, but, by and large, elements originated from magmas or igneous rocks of the outer rocky shell of the earth. Only eight elements constitute 98% by weight of the earth's crust. These are oxygen, 47%; silicon. 28%; aluminum, 8%; iron, 5%; and sodium, magnesium, potassium and calcium, less than 4% each. These common elements and the other less common ones are the building blocks of minerals, of which there are over 2,000 varieties. According to Webster: "A mineral is an inorganic substance occul.ring natura!ly in the earth and having a consistent and distinctive set of physical properties and a composition that can be expressed by a chemical formula. The term is sometimes applied to organic substances, such as coal." Thus, minerals are precise combinations of elements. Rocks, as distinct from minerals, are composed of assemblages of minerals. When minerals are found in sufficient concentration to warrant extraction by mining, the mineralized area is considered an ore deposit. The definition of ore is mineral that can be extracted from the ground at a profit. The economic connotation is implicit in the word ore. Since most of the useful elements compose such a small percentage of the earth's crust, the occurrence of ore deposits as we know them would not have transpired had not geologic processes concentrated the elements (see Sec. 4). 1.2-DEFINITIONS OF MINING TERMS Extensive coverage of the many descriptive terms used in mining may be found in a good mining glossary, such as is available from the Superintendent of Documents (see Sec. 35), but for convenience a number of the more common definitions are given here. Mining may be defined, as by A. B. Cummins, as the act, process or work of extracting minerals or coal from their natural environment and transporting them to the point of processing or use. Mining techniques are applied to extracting metallic minerals, such as ores of gold, copper, lead or zinc; to fuels, such as coal, anthracite, lignite and tar sands; and to nonmetallic minerals, such as lime-

Jan 1, 1973

By F. W. Bond

Predictive ground-water modeling is currently being applied to a wide range of engineering applications. In recent years models have been used to evaluate the effect of large ground-water withdrawals on regional water supplies; subsidence associated with overpumping; siting and design studies for chemical dumps; siting and safety aspects of nuclear waste storage; and heavy metal migration from disposal sites. Similar modeling techniques could be used to analyze water-related problems in the minerals industry such as mine dewatering (both open pit and underground), environmental and pollution control, and process water supply and disposal The objective of this discussion is to describe how ground-water models are being used to assist in the solution of water-related problems outside the industry and to extrapolate that use to mining problems.

Jan 1, 1980

By Lana Alagha, Fardis Nakhaei, Jose L. Corchado-Albelo

Tellurium (Te), a critical mineral for solar energy technologies, faces supply risk challenges that drive the development of diversified and robust production routes. This research focused on improving Te enrichment from copper tailings (CT) produced from copper porphyry (CP) ores processing, addressing the loss of ~90% of Te minerals to tailings in the flotation process of CP ores. Gravity separation and froth flotation processes were used as possible enrichment routes of Te-bearing minerals (i.e., pyrite) in CT. In the froth flotation process, synergistic combinations of reagents were tested to achieve an acceptable enrichment ratio of Te minerals. Comprehensive characterization analyses showed significant Te enrichment in the flotation concentrates. Tellurium was recovered at 90%, while the grade of Te in the concentrates was 1.4 ppm using a xanthate collector and glycol frother compared to <0.5 ppm in the flotation feed. Findings showed that Te-minerals’ enrichment was also feasible in CT using the proposed combined concentrations routes (i.e., gravity separation followed by froth flotation) by looking at Fe, Cu, and S enrichment. This study also highlighted the importance of understanding the deportment of Te minerals in different process streams to develop and optimize efficient enrichment practices.

Feb 1, 2024

By C. Sun

Due to unfavorable geological condition, excessive deformation of mine drifts occurred in a large underground copper and nickel mine. In searching for a solution, a comprehensive underground monitoring program was implemented and the opening convergence and the surrounding rock deformation were monitored. A large number of field data were collected and thoroughly analyzed. The convergence and deformation as function of time and depth were determined and a rock stability index was proposed. Based on the deformation-time and deformation-depth relations, critical deformation times and locations were identified and defined as characteristic values to be used for mine opening and support designs. The characteristic values are critical in the application of two-step supporting system, and the determination of support parameters. The application of the method developed in this study has demonstrated that this practical approach in support design and installation is effective. With the two-step supporting system, a long-term drift stability can be achieved in the mine.

Jan 1, 1998

By Robert T. DeGavre

I have been asked by the Society of Mining Engineers to present a paper on Inco Limited&apos;s Indonesian nickel project as a case study in the financing of large overseas mining projects. I welcome this opportunity It is a story worth telling not only because the project itself represents a significant human achievement but also because there are certain important lessons that can be derived from our experience in financing the project. The paper will be divided into four sections: (i) a brief history of the project, (ii) a critical appraisal of the project&apos;s financing plan in terms of the goals that we sought to achieve, (iii) some comments on certain factors underlying the relative success of the financing plan, and (iv) the contributions that the engineering staffs must make to a successful financing plan. The paper will not present a technical assessment of the project since Inco Limited has been asked to submit a series of papers on this subject at the International Laterite Symposium as part of the 108th Annual Meeting of the AIME in February 1979.

Jan 1, 1978

By R. J. Gray

Oxidation of coal can best be described as a process of deterioration, since most of the uses of coal, such as for fuel and by-product chemical and coke production, are adversely affected by coal oxidation, and the inclusion of oxidized coal in most coal products detracts from their value. There are probably many mechanisms of coal oxidation, and the ways oxygen molecules combine as complexes with coal macromolecules to form new substances have been dealt with and speculated upon by many workers1)* but are not dealt with in the present work. This study deals with tests and methods of detecting oxidized coal, with particular emphasis on the microscopically discernible changes that accompany the chemical and physical changes that affect the technological properties of coal during oxidation.

Jan 1, 1974

By R. E. Scheffel

Most supergene copper heap leach operations today employ forced-aeration, irrespective of ore grade. Unfortunately, there is little published quantification of its benefit. There is a natural desire to strive for the ideal chemical kinetics. The reality, however, is that physical mechanisms control the commercial extraction rate. This paper presents the performance of a number of operations, their operating conditions and physical ore characteristics, which contribute to non-ideal solution distribution and variable extraction rate. Regardless whether one uses forced-aeration, commercial experience to date suggests it is prudent to design for longer leach cycle times to ensure the production target is met.

Jan 1, 2006

By D. M. S. Bhatia

Twenty-six insitu analyses of cubic galena crystals from a Mississippi Valley-type deposit were undertaken with a laser microprobe spectrograph to study the variation of nine trace elements from the crystal center to its periphery, both along the diagonal and vertical. The general trend is an increase in the concentrations of Ag, Ga, Ge, and In with As showing the opposite trend Bi, Cd and Sn did not show any pattern. Sb was not detected. These variation patterns nay serve as a model for similar studies of other Mississippi Valley-type deposits.

Jan 1, 1984

By Steve Karl

"The global underground construction and tunneling industry is in pretty good shape. Billions are being spent in shoring up aging infrastructure in the United States and other places, and new underground projects are being put out for bid.With each new project, comes new equipment, technology and tunneling methods. So it is incumbent on tunneling professionals to constantly improve their knowledge of the profession. This is where spending a few days with other underground construction professionals can assist the tunneler in keeping up.Every two years, tunnelers and underground construction engineers, contractors, suppliers, designers and owners from around the world gather for the Rapid Excavation Tunneling Congress (RETC). The 2017 conference was held in June in San Diego, CA. The UCA of SME puts on the conference.This years’ RETC attracted 1,400 attendees. The accompanying sold-out exhibit totaled 188 service and equipment suppliers. In addition, the conference had the UCA of SME bookstore, where the new History of Tunneling in the United States book was introduced. And a short course on tunnel rehabilitation was featured.Technical programmingRETC 2017 featured nearly 100 technical presentations. Topics covered the breadth of the global underground construction industry. Here is a sampling of a few. The proceedings from the conference is available from SME, 303-948-4200, www.smenet.org.Accomplishing extraordinary tasks as a machine supplier for Metro Doha: The construction of the Metro Doha in the State of Qatar established a modern, safe, efficient and integrated public transportation network. Upon final completion of multiple phases, the network will comprise four metro lines with a length of 216 km (83 miles) and 100 stations. Phase one comprises 112 km (43 miles of underground tunnels (56 km or 22 miles of twin-tube tunnels). Twenty-one earth pressure balance tunnel boring machines (TBM) were deployed by the four different joint ventures. The project was initiated, managed and supervised by the owner, Transport Authority Qatar Rail.Phase two of the Doha Metro will start upon the completion of Phase One in 2019 (Qatar Vision 2030). The owner placed full faith in the manufacturer’s abilities to deliver equipment of high quality, state of the art standards within the given time frame. This paper focused on the manufacturer’s scope of delivery and on the supplier’s high standards of quality in production, logistics and services."

Jan 9, 2017

By Christos Roumpos, Philip‑Mark Spanidis, Francis Pavloudakis

Coal mining operations are large-scale, long-term frameworks of high complexity. Mining organizations accumulate, develop, and leverage knowledge from diverse scientific and technological fields as a result of these operations. Both practical experience and existing literature indicate that knowledge management (KM) methods within the mining industry primarily target solving immediate technical challenges and operational requirements. However, they are not commonly regarded as strategic tools to enhance the performance and competitiveness of mining companies. Empirical evidence from the Greek mining industry suggests that the management of available knowledge is intricate, less effective, and dysfunctional. This paper presents a methodology based on the principles of quantitative research (QNR), collaboratively conducted with a group of mining experts, to assess the KM landscape in the Greek mining industry. The methodology involves a structured data collection framework using questionnaires, subsequent statistical analysis, a discussion on critical methodological aspects, and an interpretation of results focusing on key aspects useful for planners and designers of KM systems in the mining industry. Finally, the paper concludes by summarizing the methodology’s outcomes and proposing further perspectives for research.

Mar 16, 2024

By J. R. Montgomery, T. A. Phillips, F. Blackham, D. J. Adams

Underground water, whether it is a mine seep, in situ leach solu­tion, or a pollution plume, is difficult to track and monitor. Monitoring wells are costly to drill and may be placed in the wrong spot. This report describes a test of an electromagnetic technique to track acid water draining from the Midnite Mine near Spokane WA. The tests successfully mapped the path of acid mine drainage being collected at the mine from two seeps. Several small side branches flowing to smaller seeps and a mix­ing zone where relatively clean water mixed with the acidic water, were also mapped. The study has changed previous opin­ions on the flow of water through the site and will be used as a basis for future site remediation planning.

Jan 1, 1996

By R. Wensel

A composite material consists of two or more dissimilar components. These dissimilar components retain their identities when mixed together and contribute to the properties of the composite. A composite usually consists of two parts, the matrix and the reinforcing material, or extender that is added to the matrix. Typical materials used as the matrix in composites are metals, polymers, and ceramics. The reinforcing material can be added for any number of reasons. For instance, if the matrix is expensive, an inexpensive filler may be added to the matrix to lower the cost of the product without sacrificing properties. An example of this is calcite (CaC03) which is added to systems such as polyvinyl chloride (PVC), to lower the cost. Reinforcements may also serve as a means to enhance the properties of the matrix material. For example, carbon fibers are frequently added to plastics to increase their strength, and glass spheres may be added to plastics to improve flexural strength. Mg(OH)z is added to polymers to give the property of fire retardancy. The latter is the focus of this paper.

Jan 1, 1995

By George Mandarakas, Johan van Zyl, Karl-Heinz Becker

The world’s climate today has changed compared to 10 or 20 years ago. Many countries face water shortages; water sourcing for mining activities has become harder to secure. ESG’s focus on the industry has made us more aware of the need to preserve and responsibly use the water needed for wet processing in our milling and sorting activities. In a recent greenfield project in South Australia, 10 Gigalitres per annum would be required to process 5Mtpa of magnetite [1]. Published information indicates that the mining industry consumes approximately 12 EJ per year—or 3.5% of total global final energy consumption globally [2] or 3.33 trillion kilowatt hrs. This energy consumption is significant, considering the critical role mining plays in extracting and processing essential minerals for economic development and human progress. The perception of the mining industry is that not only does it consume significant power, but it also consumes a lot of the freshwater in the world. In fact, it consumes approximately 5% [3] of the total freshwater demand. According to the Intergovernmental Panel on Climate Change (IPCC), by 2050, 60% of the world’s population will be living in countries that are classed as water-stressed [3]. As more and more emphasis is placed on renewable energy sources, the amount of water used in mineral processing will increase because more and more raw materials require a water-intensive process. This increases the pressure on the mining industry to try and find water-saving initiatives. As part of this review, recent advancements in magnets have enabled magnetite processing facilities to achieve between 30 to 40% dry gangue material rejection before the wet beneficiation process (grinding and sorting). This reduction in energy consumption allows the reduction of energy consumption. Secondly, there is less material ground in the mills, which requires less water for mineral downstream processing.

Feb 1, 2025

By M. Batzle

The upper Arkansas basin has some of the greatest potential for geothermal development in Colorado. Over several summers, students conducted an investigation using seismic, gravity, and magnetics in order to help identify the large structures and basin fill associated with the Rio Grande Rift. Adjacent to Mount Princeton Hot Springs, near surface geophysics was conducted to help understand the faulting and fractures that act as a conduit for hydrothermal flow. The methods used included high frequency 3D seismic, magnetics, gravity, D.C. resistivity, and self potential. Throughout the Mount Princeton area, passive seismic, vertical seismic profiling, and well logging were also used to better understand the geology and activity of the region. The results indicate for the area northwest of the hot springs, a 40 to 50 m thick unconsolidated layer overlying the fractured granitic basement. The DC profile shows a deep geothermal anomaly of low resistivity which correlates with a positive SP anomaly in the same region. In the Chalk Creek valley, a shear zone extends from the north east to the south west, just south of the Chalk Cliffs. There appears to be an upward migration of the water through this shear zone which then flows along the porous sediments towards the south in this area. The deep seismic data collected in the center of the basin suggests that the depth to the basement is approximately 2000m. Also identified on the deep seismic are two major faults on the west end and two minors at the east end of the cross-section. An alteration zone is identified between the faults and a possible Precambrian northeast trending shear zone. The potential for developing an Enhanced Geothermal System (EGS) near the center of the valley is high. Our geophysical results indicate a deep basin fill near the center of the basin providing high temperatures. The range front (Sawatch) fault is observed to penetrate under the center of the basin and is an attractive target for natural fractures.

Jan 1, 2011

By Håkan Stille, Jalaeddin Y. Rafi, Fredrik Johansson

"INTRODUCTIONIn tunneling projects, pre-grouting is performed with the purpose of establishing an impervious zone around the tunnel periphery. This is obtained by reducing the penetrability of the most conductive fractures in the rock mass. The main attention, besides economy of the project, is given to limiting the ingress of water into the tunnel to a certain amount during construction s well as operation period. Failure in pre-grouting process may, according to Bruce (2007), significantly affect the project in terms of safety, performance, cost and time. In this respect, determination of design parameters (pumping pressure, properties of the mix and stop criteria) affects these projects significantly. In current practices, depends on the geological conditions and requirements of the project these parameters differ widely. Weaver (1991) recommends selection of design parameters, specifically grout injection pressures, based on site specific factors and the conditions at each specific hole into which grout is to be injected (grout hole logging and water pressure test data). Houlsby (1990) correlated the allowable grouting pressure to the quality of the rock mass and the rock cover above the grouted fracture. In his methodology, grouting should be continued until the maximum pressure was attained. Later, Lombardi and Deere (1993) introduced the Grout Intensity Number (GIN), which limits the combination of injection pressure and injected grout volume in order to control the energy induced in the fracture i.e. avoid fracture jacking. Even though the GIN method was a step forward in understanding of the mechanism of the fracture deformation, there are ambiguities connected to this methodology, thus determination of the intensity number is challenging (see e.g., Rafi and Stille 2015)a.A main problem when no theoretical solution is practiced is that effects from the chosen injection pressure, such as possible increases of transmissivity and changes in total grouting time, remains hidden in the overall grouting process. The question is if a high or a low pressure should be used to fulfil the requirements of the projects at the lowest possible cost."

Jan 1, 2016

By H. Lowers, B. Van Gosen

The Iron Hill (Powderhorn) carbonatite complex is a 31 km2 alkalic intrusion located about 35 km south-southwest of Gunnison, Colorado. The intrusion has been well studied and described because of its classic petrology and architecture of a carbonatite-alkalic complex. The complex is also noteworthy because it contains enrichments of titanium, rare earth elements, thorium, niobium (columbium), vanadium, and deposits of vermiculite and nepheline syenite. In particular, the complex is thought to host the largest titanium and niobium resources in the United States, although neither has been developed. It may be economic to extract multiple resources from this complex with a well coordinated mine and mill plan.

Jan 1, 2007