Search Documents

By E. A. Martell, K. S. Sweder

INTRODUCTION Lung cancer in uranium miners has been attributed to alpha irradiation of basal cells of the bronchial epithelium by radon daughters, primarily by 7.7 MeV alphas from polonium-214 (Altshuler et al., 1964). It also has been was observed that for a given cumulative radon progeny exposure, uranium miners who smoke cigarettes have an incidence of lung cancer about 10 times higher than nonsmoking miners (Lundin et al., 1969). It has been pointed out that the large excess of lung cancer deaths among smoking uranium miners is a multiplicative effect (Doll, 1971), which suggested possible synergistic interactions between airborne radon progeny and cigarette smoking. Experimental studies of the complex pattern of interactions between radon progeny, cigarette smoke particles, and the cigarette smoking process are in progress in our laboratory. Preliminary results, reported elsewhere (Martell, 1981), implicate alpha radiation from indoor radon progeny in the etiology of lung cancer in all cigarette smokers. Cigarette smoking produces high concentrations of smoke particles of low mobility and respirable size--particles between 0.5 and 4.0 µm in aerodynamic diameter (see below). The attached fraction of indoor radon progeny is highly dependent on the air concentration of small particles from cigarette smoking and from other combustion sources (Martell, 1981). The size distribution and other properties of radon progeny associated with cigarette smoke particles enhances their effectiveness in the induction of bronchial cancer in man. In this paper we discuss the properties of radon progeny associated with cigarette smoke, the fractionation of radon progeny and modification of their aerosol properties in burning cigarettes, the role of 218Po in these processes, the production of insoluble 214Pb and 212 Pb enriched particles in burning cigarettes, and the consequent differences in the patterns of polonium isotope alpha irradiation in the bronchial epithelium of smokers. EXPERIMENTAL PROCEDURES Experimental methods used in these studies involve the use of small experimental chambers of known radon and radon progeny concentrations in combination with aerosol collection and sizing techniques and sensitive radioactivity detection methods. The use of low-level [ß-] counting for radon progeny determination, providing a measure of 214 Pb plus 214Bi activity, makes it possible to carry out chamber experiments with small radon emanation sources and relatively low air concentrations of radon and radon progeny concentrations in the range from 100 to 1,000 pCi per liter. Thus, for example, in a typical experiment we use a 10 nanocurie 226Ra solution standard in a 10 liter chamber, providing an equilibrium concentration of 1,000 pCi of radon per liter. In small sealed chambers, radon progeny plate out rapidly on the chamber walls, with steady-state concentrations of airborne progeny less than 2 percent of equilibrium levels. This is experimentally convenient because, upon introduction of high concentrations of cigarette smoke particles or small particles from other sources, there is a systematic ingrowth of attached radon progeny, providing a tagged aerosol source of known age and radon progeny composition. In some chamber experiments a 226Ra solution standard of small volume, acidified to O.1N HNO3, was used as the radon emanation source. When used with a bubbler the holdup of radon in an 8 ml volume of 226Ra solution standard at 0.1N HN03 was only 2% of the total radon in the chamber at equilibrium. For experiments with 212Pb-tagged aerosols, we used a dry Ba(228Th) stearate emanation source prepared by the method of Hursh and Lovaas (1967). 226Ra and 222Rn determinations were made by radon gas counting. The 222Rn in a sealed air or water sample is transferred, using helium gas as a carrier, successively through a dry ice cooled trap at -80°C to remove water, through ascarite to remove C02, and through a small activated charcoal trap at -80°C to collect the 222Rn. Subsequently, by heating the charcoal to 400°C, the 222Rn is transferred next to an LN2-cooled capillary trap, and finally into an alphascintillation counting cell of the type described by Lucas (1957). As already stated, radon progeny activities were determined by low-level [ß-] counting, which provides a measure of 214Pb plus 214Bi. The radon progeny samples, collected on efficient Delbag polystyrene micro-fiber filters or on impactor foils, are placed in close, sandwich geometry between two thin-walled flow counters inside shielding anticoincidence counters and a 15 cm thickness of steel shielding. This configuration provides nearly 4II geometry and a low background of only 0.25 to 0.30 cpm. Aluminum absorber was added to provide a combined thickness of absorber and counter wall exceeding 7.0 mg/cm2 to eliminate the variable contribution of 7.7 MeV alphas from 214Po. 212 Pb determinations also were carried out by low-level [ß-] counting, in this case using a combined absorber and counter wall thickness of 9.0 mg/cm2 to eliminate contribution of 8.8 MeV alphas of 21 Po. In each experiment the [ß- ]activity data were corrected for decay to an appropriate common reference time for assessment of activity distributions.

Jan 1, 1981

By K. E. Yassin, A. Yehia, M. Amar

Phosphate fines (size ≤ 45 μm), from the Red Sea Region, Egypt, were subjected to beneficiation process to recover the phosphorite grains from such fines. The sample is characterized by low P2O5 content (18.78%) associated with gangue minerals such as silica (22.77% SiO2) and carbonate (2.01% MgO) indicating its low grade. Phosphate pre-concentrate was prepared by gravity separation, using Falcon, where 63.37% of the phosphate, with 24.94% P2O5, 1.46% MgO, and 10.54% SiO2, was firstly recovered reducing the mass flow to the subsequent beneficiation process. However, the gravity tailing was the feed for the reverse phosphate flotation using bench scale column flotation where oleic acid was used as a carbonate gangue collector and amylase enzyme as a phosphate depressant. Under the appropriate flotation conditions (0.1% amylase, 5·10−4 mol/dm3 oleic acid, and temp. 30 °C), phospho-concentrate assaying 0.61% MgO, 13.14% SiO2, and 27.85% P2O5 with a P2O5 recovery of 55.45%, was finally obtained without the use of expensive depressants, e.g., phosphoric acid or sodium silicate. A tentative flow sheet for the whole process was postulated.

By H. Ikeda

INTRODUCTION [Slide 1] The Role of the MMAJ Ladies & Gentlemen, it is a pleasure for me to be able to make a speech at this SME annual meeting, representing the Metal Mining Agency of Japan. [Slide 2] Today’s Topics In my presentation today, I would like to divide my topics into four parts. First of all, I would like to describe the current situation of Japanese non-ferrous metal mining and mineral processing industries in Japan. Secondly, the supply and demand of non-ferrous metals in Japan. Thirdly, I would like to spare some minutes on the overview of overseas development by Japanese mining companies. Finally, since some people may not be sure what the Metal Mining Agency is or what this Agency, I would like to briefly introduce the Metal Mining Agency of Japan.

Jan 1, 2001

By D. Hodouin

The improvement of mineral processing data using material balance computer programs is nowadays a current practice in many plants, engineering companies or research centers. It now becomes more obvious that such programs should integrate new features such as the preprocessing of data, the estimation of less accessible process variables and an in-depth interpretation of: the computed results. A few solutions to these new problems are already available. The feasibility of a mass balance computation for instance can be examined by analyzing the degree of redundancy of the measurements prior to any data adjustment. New variables such as chemical analyses in particle size intervals or liquid phase composition can be included in a set of measurements. Finally, a sensitivity analysis can be used to analyze the reliability of the results, to detect eventual outliers or to redesign a sampling scheme. Some illustrations of these new developments are presented.

Jan 1, 1989

By MAHESH SHRIWAS, CHRISTOPHER PRITCHARD

Ventilation monitoring and control in mines are becoming an integral part of day-to-day activity for maintaining the health and safety of miners. This paper evaluates potential real-time monitoring solutions for detecting and reducing diesel particulate matter (DPM), mine fires and dust in situ and examines the state-of-the-art use of ventilation monitoring and control in underground mines for detecting and reducing air contaminants to acceptable regulatory limits. In this study, relevant documents, including research papers, trade publications and manufacturer website information, are reviewed to identify research gaps. This paper also includes evaluations of contemporary sensors (airflow, gas, dust and silica), control system and software technologies, data transport systems, the Industrial Internet of Things (IIoT), ventilation network simulators and control devices to identify potential health and safety research gaps. Examples of some mines in Canada, Australia and the United States that have been using ventilation monitoring and controls are included as well. Overall, this review identifies multiple challenges and research gaps in applying mine monitoring and control systems that could be the focus of future research, offering potential improvements to miner safety and health and financial benefits.

By E. M. Frizzell

Development of mobile crusher systems for surface mining, allowing extension of continuous conveyor haulage systems into the pit, is traced from its introduction to the present. Variations in configurations are reviewed, and the compelling reasons for using mobile crusher systems are explored.

Jan 1, 1983

By S. Natansohn

A prevalent technique for the recovery of silver from wastes generated in silver-tungsten electrical contact fabrication is electrowinning. Such scrap is placed in a permeable plastic basket which constitutes the anode compartment and this basket is suspended in a larger cell in which the cathode is mounted. A silver nitrate solution is used as the electrolyte and, upon application of an electric field, the silver migrates to the cathode where it deposits out. At times, there is tungsten migration to the cathode compartment and consequent co-deposition with the silver. This W contamination, which may amount to several thousand ppm, necessitates additional purification of the deposited Ag and its removal would therefore be advantageous. The elimination of the W impurity would also extend the operating period of the cell with corresponding increase in the Ag output and savings in labor costs.

Jan 1, 1982

By Ray A. Rothrock

The in situ mining of uranium is the process whereby chemical lixiviant is injected by means of wells into, and flowed through, an ore body. The lixiviant reacts with uranium which has been previously oxidized making the uranium soluble. The solution is then brought to the surface by means of producing wells. In situ mining disturbs the ground-water quality in the immediate area. Since ground water is a natural resource used by man, care must be taken not to allow the lixiviant to escape the local mining area. Also, when the ore body is mined out, the area should be restored to as near its original state as is reasonably achievable. The return of ground-water quality to its original state can occur naturally over a long period of time or be enhanced using appropriate technological means.

Jan 1, 1981

By Jorge Amaya, Nelson Morales Varela, Francisco Saavedra, Gonzalo Nelis, René Gómez

Precedence constraints are broadly used in mathematical models and algorithms for mine planning to model, for example, slope angles in open pit operations or connectivity in underground mines. Unfortunately, these constraints do not capture relevant geometrical aspects for the design of the mine like minimum bottom space of pits or smoothness of the economic envelope in block caves. In this work, we present different approaches that utilize precedence constraints generating economic envelops that are more suitable for design purposes. The numerical experiences show that the proposed techniques produce high value envelops with better geometrical properties and that the methods proposed can be computed efficiently.

Jun 25, 2023

By Z. Yu

The effect of particle size on coal dewatering has been well recognized However, there are no systematic studies on ultrafine coal dewatering. The results discussed last year revealed the effect of flocculant type and coal wettability on the filtration of ultrafine coal In this paper, the differences in dewatering between -25 µ m ultrafine and -500 µ m fine coal with addition of flocculants, surfactants and oil-emulsions in vacuum filtration are further investigated Significant differences were observed in the reduction of the cake moisture. The utilized emulsions were found to be very powerful and promising filtration aids for both ultrafine and fine fractions of hydrophobic and hydrophilic coal

Jan 1, 1995

By J. A. Lombardi

"EXECUTIVE SUMMARY The use of membranes for the treatment of Acid-Mine-Drainage (AMD) water has been a 35 year mining industry quest that has only recently produced commercial scale Zero-Liquid-Discharge (ZLD) plants. The process of development of the membrane treatment of AMD has been defined by the water treatment industry’s efforts to control gypsum scaling of the membranes, an artifact of the concentration of calcium and sulfate ions on the concentrate or “brine” side of the membranes. Improved anti-scalants, changes to membrane surface geometry and a lowered permeate flux rate were all part of solving the calcium sulfate (gypsum) scale formation problem. Whether used singly or as part of a multi-stage membrane treatment process, the production of “left over” membrane concentrate or brine, in any volume large or small, was a second barrier to adoption of the method by the mining industry. The two identified “final brine” treatments were a) solar evaporation ponds and b) mechanical evaporators. Brine disposal by solar means is typically site limited to flat terrains or high net evaporation locations. Mechanical evaporation-crystallization is applicable at all sites but, typically, at onerously high ownership and operating costs. Miwatek, a South African water treatment start-up, has entered the mining AMD ZLD marketplace with two new, pilot-scale tested, processes, both of which are predicated on the innovative treatment of a reasonably concentrated AMD and neither of which produces a final brine that requires disposal. In the Miwatek Brine Treatment, MBT, method the membrane brine is caustic pH adjusted and de-calcified precedent to passage through a second membrane plant. The caustic is generated on-site by a lime treatment of the second-membrane concentrate. The first- and second-stage permeates are blended for discharge. The process usually yields no “final brine” for disposal. In the Miwatek Ettringite Treatment, MET, method a low pH first-stage membrane brine is lime treated in two or three steps in the presence of aluminum in a way that metal hydroxide and calcium sulfate solids are formed and purged from the system. Sufficient aluminum is often present in the feed water to, with judicious recycling, enable operation of the lime-aluminum treatment without the purchase of outside aluminum reagent. The first-stage membrane permeate is blended with the lime-aluminum treated membrane concentrate for discharge. The indications are that the method can comfortably meet the low 250 -500 ppm SO4 discharge water quality standards that have most recently been proposed in South America. The process yields no “final brine” that requires disposal. Projected own-operate costs for the MBT and MET systems are less than the estimated costs for all identified alternative treatments."

Jan 1, 2015

By C. N. Speltz

The cost of transportation of industrial minerals is frequently higher than the cost of the product. Where a minc, industrial mineral plant. or customer is served by a single railroad, that single railroad, because of lack of competition, may increase rates and/or provide inadequate service so that the economics of that mine, plant or customer are adversely affected, or so that the level of service precludes satisfactory performance. Transloading of industrial minerals from rail-to-truck or truck-to-rail in order to improve economics and sales of product is not new. However, transloading to reduce freight costs or improve inadequate service caused by a lack of competition in the rail industry, is a relatively new concept brought on by the recent mergers of many of the main line railroads, both in the eastern and western United States. For example, with completion of the Burlington Northern/Santa Fe and the Union Pacific/Southern Pacific mergers, the western United States has only two mainline railroads. The industrial mineral producer, in order to reduce the cost of transportation, or increase the level of service, must evaluate potential transloading opportunities in light of higher prices and reduced service brought on by reduced railroad competition.

Jan 1, 1998

By D. Scott Scovira, Thomas Gustavsson

Exiting WW2, the potential of nitrates and hydrogen peroxide for application as industrial explosives both became known. The technology stream advanced the development and uptake of nitrate-based explosives to the point that they are the current global standard for blasting. Recently environmental issues are influencing the strategic agenda of extractive industries. The mid-2010s saw renewed interest in hydrogen peroxide explosives to eliminate NOx fume. Carbon reduction initiatives in the 2020s provided additional impetus to investigate hydrogen peroxide-based explosives. Hypex Bio is at the forefront of developing and delivering bulk gas sensitized Hydrogen Peroxide Emulsion (HPE) for blasting. HPE consists of hydrogen peroxide along with smaller amounts of fuel and emulsifier. The consistency of HPE is similar to industry- standard nitrate-based emulsions. It is compatible with existing priming and initiation systems. HPE does not contain nitrates and thereby does not produce post blast nitrous oxide fumes nor discharge of nitrates or ammonia to mine water. Importantly, HPE contributes to reduction in total carbon emissions as compared to nitrate-based explosives.

Feb 1, 2025

By R. L. Grayson

A goal programming-based worker scheduling model has been incorporated in the Mine Management Support System (MMSS) for assigning workers to prioritized jobs on a shift basis. In the model the accomplishment of each regular and non-regular job is a goal. The objective is minimization of the deviations away from the goals. A number of coefficients are used as premultipliers of the decision variables in order to address practical considerations associated with the utilization of workers and the requirements of jobs. Some of these premultipliers will be updated expertly within MMSS, timely updating the statuses of the dynamic parameters.

Jan 1, 1991

By Hamid Mazouz, Mohammed Hakkar, Rim Jouraiphy, Fatima Ezzahra Arhouni, Ahmed Mahrou, Aziz Boukhair, Mohammed Fahad

The wet process is the most commonly used worldwide for phosphoric acid (PA) production, in which phosphate rock (PR) is reacted with strong acid mainly sulfuric acid. This work aims on studying the rare earth elements (REEs) distribution during the production of phosphoric acid using different qualities of phosphate through various industrial technologies. At the onset of this work, the process started with 12 samples of PR, PA, and phosphogypsum (PG) being taken simultaneously from two different Moroccan basins (Ouled Abdoun mine represented by K09 and Gantour mine depicted by G10, G20, BG) and various production lines at two processing platforms (Jorf Lasfar and Safi). Afterward, collected samples were prepared and analyzed for REE characterization using an inductively coupled plasma mass spectrometry (ICP-MS). Based on the analysis results, a transfer factor ( TFX) was introduced with the aim of gauging the REE distribution between PA and PG. The results showed that the total concentration of REEs in different phosphate qualities ranged from 411 to 631 ppm; the major part of this concentration was attributed to the four elements: Y, La, Ce, and Nd which constitute more than 77%. The REE distribution between PA and PG depends on neither the phosphate quality nor the industrial technology used since that the distribution results showed that 55 up to 66% of the initial REEs in phosphate rock ended up in the PG. The behavior of each REE was common except for the element scandium, which transferred mainly to the phosphoric acid.

Nov 3, 2021

By Z. Yu

Dewatering of a -0.5 mm fine coal has been studied extensively. Deep cleaning requires however fine grinding, and dewatering of such ultrafine products presents a great challenge. Several coal samples finely ground and characterized by different wettabilities have b.een used in the filtration tests. Vacuum and press filters have been employed. In this paper only the results obtained with different flocculants (totally hydrophobic. semi-hydrophobic and hydrophilic polymers) are included. The results reveal the effect of coal surface properties and flocculant type on filtration of ultrafine coal.

Jan 1, 1994

By Kyle Amoroso, Larry Applegate, Aaron K. McCain

The use of frozen soil as ground improvement and temporary ground support for the excavation and construction of cross passages and adits has gained in popularity over the last decade. Frozen soil provides a number of advantages for this application such as being waterproof, structurally stable, and working well with any soil type. One of the greatest advantages is the ability for the system to be adaptable to the project geometry and site limitations. Multiple case histories illustrate that freezing can occur from the ground surface, from within the tunnel, or as a combination.

Jun 13, 2023

By Yubo Tu, Lianqi Wei, Tianyi Zhao, Peiwei Han, Zhengchen Li, Shufeng Ye

The effect of oxygen partial pressure on the volatilization percentages of valuable metals from iron-rich pyrite cinder by chlorination-volatilization method using CaCl2 as chlorinating agent was investigated in this study. The volatile products were collected directly and analyzed by X-ray diffraction. It was found that there were CuCl2, CuCl, PbCl2, and ZnCl2 existed in the volatile products. Au and Pb volatilization percentages were almost not affected by oxygen partial pressure. Both Cu and Zn volatilization percentages were negatively correlated with oxygen partial pressure when CaCl2 dosage was no more than 4 wt%, and almost uncorrelated with oxygen partial pressure with a CaCl2 dosage of 6 wt%.

Dec 19, 2023

By Arman Hazrathosseini, Ali Moradi Afrapoli

Fleet management systems (FMSs), as a pivotal part of any surface mining operation, need to evolve from conventional to intelligent systems because of both Mining 4.0 requirements and some shortcomings inherent in conventional methods. However, this novel transformation needs to be investigated technically and strategically. To this end, previously published research works on intelligent FMSs are explored to track the latest status of these third-generation frameworks within the surface mining context. Their underlying models are then compared in terms of five categories of allocation and dispatching features to pinpoint the technical gaps ignored. Having drawn the future lines of research, the present work then leverages the popular SWOT analysis method to outline the strengths, weaknesses, opportunities, and threats associated with the advent of these intelligent FMSs in mines of future. By and large, the analysis indicates that advantages outweigh disadvantages. Solutions are offered to address the existing weaknesses and threats.

Apr 1, 2024

By Matthew Burdick, Andrew Rule, Erica Bailey

The Second Narrows Water Supply Tunnel, Burrard Inlet Crossing project for the Greater Vancouver Water District entails deep shaft construction, subway sized pressurized face tunneling through highly variable ground conditions, installation of three permanent steel water mains and construction of elaborate valve chambers adjacent to either shaft. The paper discusses key elements of the planning and implementation of 6.69 m Ø slurry mixshield tunnel boring machine (TBM) assembly in a small diameter deep shaft including incorporation of a fully pressurized launch lock, preparations for saturation diving, surface support infrastructure and initial mining sequence.

Jun 13, 2021