Search Documents

By R. M. Carland, F. F. Aplan

The ion-exchange capabilities of natural zeolites from the western United States, representing the species chabazite, clinoptilolite, erionite and mordenite, have been studied because of their potential use in environmental remediation and in hydrometallurgical processes. These raw zeolite samples were found to contain Na+, K+, Ca+2 and Mg+2 as exchangeable cations, and all of these, with the exception of Na+, were found to seriously interfere with the exchange of Cu+2 from solution. Placing these zeolites in the Na+ form was found to increase their cation-exchange capacity, often massively. In addition, the elution of Cu+2 from the Na+ pre-exchanged zeolite is greatly facilitated when the deleterious K+, Ca+2 and Mg+2 have been largely expelled. The relative influence of these deleterious ions on the uptake and elution of Cu+2 was determined.

Jan 1, 1996

By L. Piga, G. Belardi, V. Alesse, N. Shehu, J. Freund

The physico-chemical interactions among minerals such as olivine, chromite and serpentine; the most commonly present ions in solution such as Ca and Mg; and flotation reagents such as EDTA and oleic acid were investigated. The study was conducted via release tests, electrophoretic measurements and microflotation of selected minerals coming from the Kukes deposit in Albania. The results were confirmed in beneficiation tests on two ores, one from the Kukes (Kalimash) deposit and the other from the Rizo deposit in Greece. It was demonstrated that, when Na-oleate is used as collector, chromite, olivine and serpentine can be separated at pH 2.5 and/or pH 5.5 when employing ethylenediamine tetraacetate (EDTA) on previously deslimed material. This approach ensures flotation concentrates with a Cr203 content better than 50% with a recovery of more than 75%.

Jan 1, 1998

By Guillermo P. Selas

Perhaps this is the first time that an analysis of the industrial minerals panorama has been made in Mexico for that type of commodities. Because the non-metallic minerals lack the glamour of the metallic minerals and are usually of less unit value than metallics, a comparative study of these commodities has seldom been attempted. Sulphur, fluorite, barite and few others are an exception. Consequently, the statistics on the lowest per unit value industrial minerals, such as limestone, dolomite, gravels, sands, etc., are usually scarce and not always accurate. The following, then, will be an attempt to show a general status of the industrial minerals in Mexico with due reservations regarding volumes and values. According to Kruger (1971), this group of minerals surprisingly very little known, and called non-metallics because the lack of metallic luster, is the largest group of the mineral kingdom. It constitutes perhaps 75% of all the mineral varieties. For the most part, these minerals are compounds of common acids, sulphides, hydroxides and two elements carbon and sulphur. The list of non-metallic minerals is therefore very long. It includes the borates, carbonates, chlorides, fluorides, nitrates, phosphates, silicates, sulphates and less commonly arsenates, chromates, molybdates, sulphides, tungstates and vanadates. The latter group and many of the oxides are sought usually for their metal content.

Jan 1, 1974

By Georgios Kafantaris, Carsten Bonde, Nataša Katic

Within the investigation works for the Copenhagen Cityring metro, Geo/CMT have carried out 90 geotechnical boreholes. Together with the previously available investigation, this resulted in more than 15 km of vertical drillings and several thousands of laboratory tests. The design is made for 17 stations, four shafts and two parallel 16 km long tunnels. The geotechnical investigation and design have been carried out in several stages comprising appropriate refinement of structural design and design of excavation operations, including TBM break-in and launching operations at each station shaft. Acceptance of the solution and / or refinement of the investigation and design schedule in the next stage were based on the geological conditions, area availability at surface level, planning and cost-control criteria. The applied recursive design refinement is presented herein with an example of the Østersøgade shaft location.

Jan 1, 2016

By John C. Harkey

The paper shares programs that presently use the CDC PLATO System to train individuals in industry. A short history of PLATO development; as a training system is presented with reflection on the major training trends being used to improve training effectiveness. A discussion is offered to describe the benefits of using a system for individualizing instruction. An introduction; is offered showing how one can recognize' individual differences, with an explanation of how the strengths of a computer are used to deliver and manage the training. Simulations of hazardous processes are shown to be one of the most effective uses of the computer for training.

Jan 1, 1979

By Richard L. Ash

Less than optimum production in mining always results when poorly blasted material is provided at loading points. More often than not the cause is due to blasting founds that fail to fully control and utilize explosive energy. In many cases the problem exists because too few blasters understand how blastholes actually break rock and recognize that blasting is a three-dimensional process in designing their blasts. To better understand how blasts can be more effectively designed the two major rock breakage processes are described. In addition, the respective contributions of the borehole and detonation pressures are defined as are the specific roles of the several important blasting design variables. The concept of stiffness as an engineering principle and its significance in blasting design is introduced for explaining the breakup of rock. Basic guidelines for affecting control over fragmentation and side effects like over-break are offered.

Jan 1, 1975

By Felicia F. Peng

Employing the combination of two types of polyelectrolyte might become necessary to enhance both settling rate of the flocs and water clarity of fine particle suspension in high capacity thickening process. The sequence of addition, mixing, type and dosage of polymer affect the overall performance and capacity of a thickening process. For the sedimentation of copper flotation tailings, the cylinder test results showed that two different techniques may be used to achieve the required performance including high settling rate of flocs, underflow density and overflow water clarity, by either adjusting pH prior to anionic polyelectrolyte flocculation, or using a combination of polymer flocculant and coagulant (dual polymer system). The dynamic thickening testing results showed that only the approach using a dual polymer system is able to meet the required performance. The effects of polyelectrolyte dosage, the sequence and numbers of polyelectrolyte addition, feed concentration, bed level and rake speed on the settling rate, underflow solid, and water clarity were studied in cylinder test and a laboratory dynamic thickening unit with various conditions related to the thickening process. The dynamic test is especially valuable in evaluating the addition and mixing of polymers. The results were evaluated quantitatively, using total suspended solids in supernatant, underflow density and capacity per unit settling area per unit time as the measure of effectiveness. The objective of this study is to quantify and explain some of the parameters involved in the sedimentation of copper flotation tailings.

Jan 1, 1997

By Frank H. Skelding

A new, large mine is about to be born. Many years and millions of dollars have been invested in exploration. An orebody has been found and proven. All necessary political and legal work to establish rights and conditions for development are complete. The feasibility studies are favorable. Financing has been arranged. Board approval has been given to proceed. The time has come to engage a contractor to design and build the new facilities in a location, as is the common case today, far re¬moved from the centers of advanced technologic development where the minerals will ultimately be used. A select list of Engineering and Construction (E&C) companies is asked to prepare proposals. At this point the common viewpoint among mining companies is that the company's sole remaining problem, a major one to be sure, is to select qualified contractors to design and build the project at the lowest cost and shortest time possible so that production can start generating a return on investment. The purpose of this discussion is to explore the viewpoint of the large E&C contractor toward such projects. It differs in important ways from that of the client mining company and it is these differences and the reasons for them that must be understood by the client if severe difficulties and misunderstandings with the contractor, starting at the beginning of contract negotiation and continuing through design and construction to final startup are to be avoided or minimized. Often enough, the difference is in degree, not kind, which only serves to obscure the fact that a difference exists.

Jan 1, 1975

By John E. Litz

Coca Mines Inc. is a medium sized company exploring for and developing precious metal properties in the Western United States. They own interests in a number of properties which contain reserves of gold and silver. The Hog Heaven property presently is under development for a combination of open pit and underground mining, followed by recovery of the silver and gold by cyanidation. Property Location The properties included within the Hog Heaven Project are located in Flathead County, northwestern Montana. The property is readily accessible by road from either Polson or Kalispell, Montana, Figure 1. [ ]

Jan 1, 1984

The impact of smoothing on the definition of ore and waste boundaries using linear estimation and conditional simulation methods is discussed. The nature of transfer functions is examined including their ability to incorporate categorical data (e.g. a dominant lithology code). An Ore Block Optimization (OBO) transfer function is presented that provides a clear guide for the mining geologist. Advantages are seen in defining stockpile cut-off grades and meeting production targets such as maximizing head grade, maximizing ore tonnes or minimizing ore loss or dilution. Each of these scenarios impacts on mine profitability and grade control.

Jan 1, 1999

By K. F. Unrug

The research work reported in in this paper deals with the monitoring of roof behavior in a drift mine located in Eastern Kentucky operating in the Coalburg Seam. The thickness of the seam at the monitoring site ranges between 9 and 10 feet with the immediate roof changing from sandstone to shale then back to sandstone. Shale thickness varies between 0 and 2.5 feet. The characteristics of the immediate shaly roof were monitored with 38 dynamometers which were set up in three survey lines to cover the entire range of shale distribution. The dynamometers are capable of providing accurate load readings in the range of +/- 5 pounds. To closely observe the contribution of moisture toward roof deterioration the dynamometers were set up in intake and neutral airways. A television borescoping camera was used in conjunction with the dynamo- metric instrumentations at pre- determined observation holes to physically observe and record the separation process of the shale and sandstone stratum with respect to time. Monitoring took place between January 1985 through January 1986 in order to cover a full cycle of dry and wet mine conditions associated with the seasonal changes. Analysis of the data show a trend of roof deterioration induced by condensation and eventual penetration of moisture within the immediate roof bedding planes, leading to rapid disintegration of the mine roof.

Jan 1, 1986

By W. J. Guay

Carbonaceous gold ores containing gold dispersed in sulfides are refractory to cyanidation because: ( 1) the carbonaceous materials adsorb gold during cyanidation; (2) a portion of the gold is so finely dispersed in the sulfide mineral lattice as to preclude contact with cyanide solution; and (3) a portion of the gold is chemically combined with carbonaceous material. Techniques which have been used to treat these ores are: (1) roasting or chemical oxidation to decompose sulfides and carbonaceous materials; (2) flotation to reject carbon; (3) the use of kerosene or other reagents to passivate the adsorptive carbon compounds; (4) carbon or resin in pulp; (5) flotation of a bulk concentrate which is treated by one of the above methods; and (6) the use of chelating agents which have a stronger affinity for gold than the activated carbon in the ore.

Jan 1, 1981

By William P. Lorenz

Overlying the sulfide mineralization at Anamax Mining Company's Twin Buttes Mine is an oxidized zone up to one hundred meters in thickness. The principal copper minerals in this zone are chryso-colla, tenorite, cuprite, native copper and copper-manganese-iron wad. This ox¬idized zone also contains minor amounts of uranium ranging in concentration from 0.002 to 0.010 percent. Since pit development through 1980, some 38 million tonnes of oxide ore with copper contents greater than 0.6 percent have been brought to the surface. Copper in the oxide ore is extracted at Twin Buttes in, an agitated sulfuric acid leach plant followed by solvent extraction and electrowinning producing 90 tonnes per day of copper cathode. During leaching of the oxide ores small amounts of uranium are solubilized along with the copper values. This is not limited to Twin Buttes as most acidic copper bearing leach solutions throughout the southwestern United States contain small amounts of uranium.1

Jan 1, 1982

By J. E. Murphy, Y. Topkaya, R. E. Johnson, B. R. Palmer, D. K. Dysinger, R. B. Bhappu, A. E. Clark

The U.S. Bureau of Mines utilized a central composite experimental design to investigate leaching kinetics of pure chalcopyrite in the sulfuric acid-oxygen system. The six factors studied were oxygen pressures of 150, 300 and 450 PSI, leach temperatures of 35O, 65O, and 95O C, oxygen-to-chalcopyrite mass ratios of 0.5, 1.0 and 1.5, leach times of 8, 16 and 24 hours, initial acid strengths of 0.6, 1.2 and 1.8 g H,SO,/g chalcopyrite and pyrite to chalcopyrite mass ratios of 0, 1, and 2. Chemical analysis and oxygen consumption measurements indicatedthat leaching occurs through three consecutive reactions. Temperature was the primary determinant of leach rate and solution acidity was the primary determinant of oxygen consumption, sulfur oxidation, and activation energy.

Jan 1, 1993

By V. Claremboux

The transformation of raw iron ore into high quality steel can take place via several processes. A general consistent theme involves the upgrading of the iron ores via methods such as flotation and magnetic separation, the preparation of an agglomerate such as via pelletization or sintering, the smelting of the agglomerate into a high grade iron product, and the further refining of iron into specific steel alloys. Each of these steps admit potential for optimizations and alternatives, and the process overall is critical to meeting the world’s continuing iron demands.

Feb 1, 2025

By Joe B. Rosenbaum

Fine-sized mineral wastes discarded by ore milling plants require stabilization to prevent air and water pollution. Methods devised for achieving this stabilization include physical, chemical vegetative, and combination procedures. Although vegetative reclamation is preferred to physical and chemical stabilization, it is difficult to achieve because the wastes are sterile, contain deleterious inorganic salts, and lack the essential nutrients and physical characteristics required for sustaining vegetative growth. Nevertheless, recent research has developed methods for producing vegetative growth on all but excessively acidic, basic, or saline tailings at costs ranging from $100 to $650 per acre. This report summarizes effective procedures developed for vegetating average tailings, the cost differential between the various methods, and suggests procedures that may be applicable for achieving stabilization of pyrite-containing wastes that may oxidize and become excessively acidic. The use of buried layers of sewage sludge to prevent this acidification is discussed.

Jan 1, 1972

By Dale R. Ralston, Roy E. Williams, Gerry V. Winter, George L. Bloomsburg

INTRODUCTION The majority of ground water flow models have been developed for large computer systems. Most of these operate under a batch mode of operation, that is, the data are input with a deck of punched cards. The advent of micro- and minicomputers over the last few years opens the possibility of adapting many of these large flow programs to the smaller computers. In general, this adaptation will require more computer time to run the program, but in many cases if the small computer is in-house, the overall cost may be less than that required for a large computer. There are also a number of peripheral devices that can be used to make the data input much easier. As an example, the use of a digitizer with a finite element or finite difference mesh reduces the data input time considerably; the use of a graphics terminal for display of the mesh immediately after it is developed shows immediately whether there are errors in the location of node points. DEVELOPMENT OF AN INTERACTIVE SYSTEM The finite element program, UNSAT2, has been used over the past several years by the authors for several ground water flow problems (Bloomsburg, 1977; Bloomsburg and Wells, 1978; Zahl and Bloomsburg, 1980). In the past these programs have been run on an IBM 370/ 145 computer under the batch mode of operation. One difficulty that has been encountered has been in determining the length of time step that must be specified for operation of the program. The problem is that if the time steps are too large, the program becomes un- stable and operation ceases. If this happens in the middle of the problem, the only alternative is to reduce the length of time step and repeat the entire run. This problem has been alleviated in other pro- grams by using a subroutine that determines the time step automatically. If the solution becomes unstable, the time step is reduced automatically and that portion of the solution is repeated. With an interactive system this can be done by storing the output pressures and restarting the program with the new output pressures. Under the batch mode of operation, there is an option in UNSAT2 that allows restarting of the program from the last point of solution, but this must be specified when originally starting the program. The interactive computer system that we use currently consists of a PDP 1 1 /23 with hard disk drive, CRT terminal, plotter, graphics terminal, digitizer, and printer. The computer has 256 K bytes of core storage and the hard disk drive will accept a 5.2 M byte disk. To run a large program on a computer such as this, some overlaying must occur; that is, subroutines are stored on disk and put into core storage only when they are actually needed for running the program. UNSAT2 required very few changes to run on this computer but some changes were necessary to take advantage of the interactive capabilities of the system. One of these changes consists of the development of a program called DBUILD to build the data file for running the program. This program calls for each piece of data by prompt statement and gives instructions for using the digitizer. The data are then entered in completely unformated form. The node points must be entered in order and the coordinates are determined automatically by the digitizer. The pressure readings or initial conditions on each node point are entered through the terminal. All element information also is entered through the terminal. After DBUILD is run the mesh may be displayed immediately on the graphics scope whereupon any error in node point

Jan 1, 1986

By J. P. Van Dillen

Continuing interest in processes that will effect separations in the fine particle size range has prompted intense interest in the use of high gradient magnetic separation (HGMS) for beneficiation of uranium ores. Some of the uranium minerals are paramagnetic and hence are amenable to concentration by HGMS. This paper presents a brief review of the problems associated with uranium ores beneficiation, a description of the HGNS process, and the effects of the parameters--pulp velocity, field strength, matrix loading and magnetic field gradient on product recovery and grade. Unsatisfactory separation of uranium minerals by HGHS is related to ore specific properties such as lack of liberation, fine dissemination of uranium minerals, uniform distribution of magnetic minerals throughout the ore matrix and interference of micron sized slimes. Experimental techniques to identify and resolve some of these problems are outlined.

Jan 1, 1982

By J. B. Hiskey, X. H. Jiang

The extraction of gold from chloride solutions by ion exchange is examined. It is shown that at initial gold concentrations between 1 - 5 ppm, 20 g/l C1- and pH 5, the kinetics of loading on weak base resins are slightly slower than those observed with activated charcoal. Equilibrium loading of auric chloride varies considerably as a function of pH from one resin to another. For all of the resins studied, nearly complete gold extraction was achieved between pH 2 and pH 6.5. Sodium hypochlorite was found to exhibit a slight effect on the equilibrium loading of gold chloride.

Jan 1, 1990

By W. C. Yates

Lack of visibility from large, open-pit haulage truck cabs has become a serious safety problem. Anaconda conducted a research program to develop a low cost system to alert haulage truck operators to small vehicles present in blind areas. Several systems were developed and tested. As open-pit haulage truck size has increased, so has the size of the blind areas. Mine utility vehicles, pickup trucks, and cars are concealed within these blind areas and become safety hazards. Figure 1 shows the typical blind areas of a 136 t (150-ton) haulage truck. The areas of greatest concern are at the rear center and front right corner of the truck. In these "no visibility" areas many small vehicles have been crushed by large haulage trucks at various mine sites. In most instances, the occupants escaped the vehicle before it was destroyed. But injuries and death have occurred. In most cases, the accidents were attributed to negligence or carelessness by the small vehicle driver. The limited visibility problem still exists, though, and a solution is needed. Initial Solution The usual plane mirror on the driver's side and the convex mirror on the right front of the haulage truck allow only limited rear visibility. The typical, right side convex mirror is generally small and difficult to locate at a glance. This convex mirror also presents an image that distorts distance perception. These mirrors are of¬ten broken and immediate replacement not demanded or made. The US Bureau of Mines, in a contract with M.B. Associates, San Ramon, CA, developed an improved visibility system. It consisted of a larger, left view mirror and unique, blind area viewer. The large 230 x 690 mm (9 x 27 in.) left mirror has a small convex spot mirror near the bottom. The entire unit can be quickly replaced if broken. The large size provides a full view of driver orientation features such as the rear tire and the top of the load bed. The right 300 x 410 mm (12 x 16 in.) mirror has a convex surface and is quite rugged. The 510 mm (20 in.) spherical radius presents the operator with some distance distortion, but objects in its view are easily seen. The "blind area viewer" consists of a modified fresnel lens that allows the driver to "look around the corner." Installation of three of these lenses on the front of each haulage truck is rec¬ommended for adequate blind area coverage. This system significantly increases an operator's field of view and allows viewing of objects within about 3 m (9.8 ft of the truck. Many open-pit mines are nor mounting on smaller vehicles a long whip with a flag and lamp or both. This increases vehicle visibility to haulage truck operators. The whip is permanently attached to the mine vehicle. It can also be magnetically attached to transient vehicles. The whip system. though, is inadequate for visibility in the critical rear and right front blind areas. Alternate Solutions All of these visibility aids as¬sume an attentive driver. In addi¬tion, areas such as the rear blinc, area are not covered. Based on the inadequacy of existing visibility systems, Anaconda made a com mitment to further the truck de¬tection technology. The best ap¬proach was considered to be ar active system. It would notify the haulage truck operator that an en¬croaching vehicle is present. Sev¬eral systems were considered, in¬cluding ultrasonics and elec¬tromagnetics. For the ultrasonic system, com mercial and in-house design were looked at. Designing an( building transducers with the spe cific beam shape to match the haulage truck blind spots re¬quired a major technological breakthrough. False alarms ap¬peared difficult to prevent en¬tirely. They were caused by pass¬ing, trailing, or leading vehicles a., well as nonthreatening objects. As a result of these problems, the ul¬trasonic technique was not pur sued. An alternative, an electro

Jan 7, 1982