Search Documents

By Rick Bearce, Minsu Cha, Mike Mooney, Yuanli Wu, Lisa Mori

"Proper soil conditioning is critical for effective earth pressure balance (EPB) TBM tunneling. Chamber pressures can reach 3-5 bar yet the vast majority of testing is performed under atmospheric conditions. This paper illustrates how pressure influences foam stability and conditioned soil behavior, and how atmospheric test results must be viewed in the context of expected chamber pressures. Torsional shear strength, compressibility and abrasivity of foam conditioned sand were found to be ideal when the void ratio was above the ASTM-determined maximum void ratio, achieved by sufficiently expanding the soil grain structure with foam, herein when the foam injection ratio at pressure exceeded 45%. Otherwise, the engineering properties of foam conditioned sand were not ideal, i.e., appreciable torque and abrasivity, low compressibility. INTRODUCTION Proper soil conditioning is critical for effective earth pressure balance (EPB) TBM tunneling. The formation soil at the cutterhead must be transformed into a highly compressible, low shear strength and low permeability medium within the excavation chamber to allow effective EPB performance. This behavior must be maintained for a certain residency time while the soil is in the chamber and screw conveyor. The vast majority of published studies on conditioned soil behavior have been performed under atmospheric conditions (Quebaud et al., 1998; Bezuijen et al., 1999; Psomas and Houlsby, 2002; Vinai et al. 2008; Thewes et al., 2012; Peila, 2014); however, the desired soil behavior must occur under chamber pressures that can reach 5-7 bar. The influence of pressure on conditioned soil is significant and is dramatically different than behavior under atmospheric pressure (Williamson et al., 1999; Mori et al., 2015). This paper illustrates how pressure influences conditioned soil behavior and how atmospheric test results must be viewed in the context of expected chamber pressures. The influence of pressure on foam bubble size (including with time) is shown through digital image analysis. The influence of pressure on foam half-life is also investigated. The compressibility, shear strength, and abrasivity of conditioned soil under pressure is presented and explained in terms of density, soil and air compressibility and porosity."

Jan 1, 2016

By S. K. Kawatra

The fly ash from coal combustion often has a high unburned-carbon content. This can make it unusable as a cement admixture, which is the major fly ash utilization market. As a result, high-carbon fly ashes currently disposed of by landfilling, at sometimes considerable expense. In this paper, the use of froth flotation to remove the unburned carbon from fly ash is described. Three different fly ashes were studied, which had Loss-on-Ignition (LOI) values of 6.79, 6.90, and 11.11 %. It was found that the use of an alkanolamide/oil mixture as a froth-conditioning reagent could greatly reduce the amount of collector needed, by increasing the affinity of the collector for oxidized carbonaceous surfaces. For each of the three fly ashes, froth flotation reduced the LOI of the ash to less than 2% which is well below the ASTM specification of no ' more than 6.0% LOI for Class F fly ash. Increasing carbon content of the ash tended to increase the quantities of reagents needed in flotation.

Jan 1, 1996

By Samuel S. Adams

The Grants uranium region of northwest New Mexico is the largest uranium district in the United States (approximately 50% of U.S. production plus reserves) and one of the largest In the world, with approximately 900 million pounds U308 production plus reserves. Deposits of the region are unusual among sandstone deposits for their high content of epigenetic carbonaceous material, generally interpreted but not proved to be of humic origin--that is, co-extensive with uranium in the primary deposits. Virtually all production in the region has been from the Jackpile Sandstone and Westwater Canyon Member of the Jurassic Morrison Formation. The tabular uranium deposits contain, in addition to humate and uranium, significant authigenic phyllosilicates, quartz overgrowths, humate-replaced detrital silicates, and a trace-metal assemblage typical of other sandstone uranium deposit types. Surrounding the deposits in the two sandstone units of the Morrison Formation is an alteration zone within which iron leaching has altered detrital ilmenite-magnetite to residual masses of titanium oxides. Feldspar alteration is locally present within this zone, below deposits in the Jackpile Sandstone, and above those in the Westwater Canyon Member. The feldspar alteration increases in inten¬sity toward the Brushy Basin Member which separates the two sandstone units, ranging from partial replacement to replacement and dissolution of plagioclase and sanidine. Spatial relations among the epigenetic humate, authigenic silicates, and the broad alteration zones that extend from the Brushy Basin Member to and including the uranium deposits suggest that (a) the organic material was involved in the unusual silicate alteration, transport, and authigenesis, and (b) that the humates originated in shales of the Brushy Basin Member. Stratigraphic relations among the Brushy Basin Member and the overlying Jackpile Sandstone and underlying Westwater Canyon Member suggest [in turn] that there was continuous, interfingering deposition controlled in part by contemporaneous basement subsidence along northwest- and northeast-trending zones. Following minor erosion of upper Jackpile Sandstone and deposition of basal organic-rich Cretaceous sediments, the silicates of the Jackpile Sandstone were once again altered by organic-bearing fluids, this time permeating down from Cretaceous sediments and partly obliterated ore-stage alteration.

Jan 1, 2013

By Nathaniel Arbiter

After almost 60 years of application in this country froth flotation is still by far the most important process for concentrating metallic ores as well as a number of nonmetallic ores including fluorspar, phosphate rock, and potash. Its use on iron ores and coal is increasing. In the metals groups the largest plants and the greatest progress are found in copper and molybdenum mills, and the section of this paper that deals with applications will be found most pertinent to that field. During its long reign the flotation process has passed through several phases of evolution and has achieved progress in economy, efficiency, and simplicity of operation. Much of today's success in the flotation of low-grade ores can be attributed to that progress. Even more important to us than our ability to cope with today's conditions are tomorrow's problems, which we can contemplate with some prescience and confidence. Our annual production of copper, lead, zinc, and molybdenum--to mention only the most important metals occurring in the U.S. as sulphides--must be held at a high level in the face of a declining grade of ore. It is probable that the tonnage of such ores mined and processed will double in this country before the turn of the century. Not only will many of the existing flotation mills be enlarged again and again, but larger mills will be built here and abroad to meet our needs. At this moment, in fact, there are at least three proposed new foreign mills or expansions that envision 100,000 tons daily milling rate on copper ores. Table I (1) shows the trend in copper ore grades in U.S. in recent years:

Jan 1, 1970

By M. Spangler

FirstMiss Gold installed a supervisory control system based on Pavilion Technology's Process Insights neural network software and Oil System's PI data historian. The primary goal of the system was to control the acid preconditioning circuit. However, our first successful control loop was on the limestone feed rate to the neutralization circuit. The information gained by modeling these circuits and the better control provided by the system has resulted in reagent savings of over $80,000 per month.

Jan 1, 1995

By K. H. Boss

In modern iron pelletizing plants fuel consumption has been optimized to such an extent that only minor savings can be expected in the future. Inspite of this fact, different process parameters were studied with a mathematical model and firing tests. The influence on fuel consumption and productivity was established. Furthermore, the adoption of simplified firing patterns was investigated, in particular for coal firing. In view of high costs of oil and natural gas, only substitution of these fuels by coal can substantially reduce production costs. In existing plants partial replacement of oil and gas can be achieved by addition of coal to the iron ore feed and by firing the pellets with pulverized coal. Two systems have been developed for the Lurgi- Dravo travelling grate process which enables coal to completely replace oil or gas. This paper describes in the first part the potentials for fuel savings available in the Lurgi-Dravo process. In the second part, different techniques for the use of coal as fuel in iron or pelletizing plants and in particular the recently developed Lurgi Multistage Coal Injection and Combustion Process (LMC) are discussed. Combined with the LMC process, a wide variety of iron ores and coals - also with high ash contents - can be used in the Lurgi-Dravo travelling grate process.

Jan 1, 1983

By Bernard Scheiner

A number of wells were drilled at two phosphogypsum stacks, one at P-21 owned by IMC and the other at Agrico's South Pierce Stack. Each well was sampled, and composites representing 5-ft increments were leached with synthetic rainwater to determine the extent of metal and nonmetal migration. To simulate what was occurring in the stack, composite samples were placed in a column, so that the column represented the stack in miniature form. Leaching experiments showed that both metals and nonmetals moved down the column when water was added to the top of the column. Data obtained from P-21 showed that with time the concentration of metals and nonmetals reached equilibrium values. The concentration of Ca, SO4, F, Si, and PO4 were -600 ppm,~1,500 ppm, 32 ppm, 14 ppm, and 22 ppm, respectively. Column leaching of South Pierce material, representing 0 to 55 ft of stack, showed that after 355 in. of water, the stack was near equilibrium values down to the 33-ft level. With continued addition of water, the portion of the stack at equilibrium would continue to increase and eventually reach the values observed for P-21. The test showed that the sulfate concentration of the effluent from the stack would never reach the USEPA standard value of 250 ppm. During the leaching test, it was determined that the permeability of the phosphogypsum in the columns was 0.000103 cm/sec. This number was used in the modeling. The data obtained from the leaching experiments cast some doubt on the practice of entombment now being practiced for closure of phosphogypsum stacks. The data clearly shows that with time, the amount of material leaching from the stack is low in concentration, with only the calcium and sulfate at higher levels. When a stack is closed at an existing operating plant, allowing rainwater to fall on the stack and capturing the solution in the existing pond system would eliminate the need for covering the stack, since with time the closed stack would continue to leach and at some point reach the equilibrium values of the P-21 stack. Entombment means that the leachable material in the stack will always be there and will require monitoring forever. Allowing rainwater to decontaminate the stack may be the best environmental solution to the problem.

Jan 1, 1999

By Jean E. Kiel, Rob Dorey, Dirk J. A. van Zyl

1.1 INTRODUCTION This chapter seeks to provide an overview of important factors involved in the implementation of heap leach technology as a vehicle for gold extraction from its ores. Toward this end, brief discussions of the various elements important to this process are presented here. Topics covered in this chapter include a brief history of the process; basic chemical reactions responsible for the process ; characteristics of ores amenable to heap leaching; location of the greatest concentration of heap leach projects in the U.S.; heap leach components, methods, regulatory/permitting considerations; and economic considerations. Most of these subjects are treated at much greater length in subsequent chapters. Thus, this chapter serves as a summary for those which follow, in addition to providing the reader with a feeling for those topics which may be of most immediate interest. 1.1.1 History of the Process Modern Day Precious metal heap leaching technology has developed over the past decade, although the principles of heap leaching per se, as well as those of gold extraction through cyanidation have a long history (see discussion below). However, it is in the past 10 years that heap leaching has developed into an efficient method of treating oxidized gold and silver ores. It has proven to be both an efficient way to extract precious metals from small, shallow deposits, as well as an attractive way to treat large, low- grade, disseminated deposits. Heap leaching has several advantages compared to conventional milling (i .e., crushing, grinding, and agitation leaching). In general, these advantages include simplicity, lower capital and operating costs, shorter start-up times, and less intensive environmental regulatory concerns. A possible disadvantage of currently existing heap leach technology is a potentially lower percentage of metal extraction being obtained from the ore than would be the case with conventional milling (Potter, 1981; Hiskey, 1985; and Thorstad, 1987) The actual principle of heap leaching has a long history as inferred previously. For example, mines in Hungary recycled copper-bearing solutions through waste heaps in the mid-sixteenth century (Hiskey, 1985), and Spanish miners percolated acid solutions through large heaps of oxide copper ore on the banks of the Rio Tinto around 1752. By 1900, leaching operations were employing such techniques as leach/rest cycles to maximize copper recovery (Taylor and Whelan, 1942; Thorstad, 1987). Copper dump leaching is currently

Jan 1, 1988

By L. J. Drew

The plate tectonic setting, regional geology, and certain aspects of the economic geology of the iron-rare-earth-nio-bium ore bodies at Bayan Obo, Inner Mongolia, China, were studied by a team of geologists from the Tianjin Geologic Research Academy and the U.s. Geological Survey between 1987 and 1989. These ore bodies were formed by hydrothermal replacement of Middle Proterozoic dolomite in an intracontinental rift setting. A variety of veins and/or dikes that have a carbonatite-like mineralogy cut the footwall clastic rocks and migmatites. A stockwork of veins occurs at several locations in the footwall. The hanging wall is a shale that has been converted to a K-metasomatite and has microcrystalline potassium feldspar as its principal constituent. This shale served as a sealing caprock that contained the chemical solutions that reacted with the dolomite and that created the enormous concentration of mineralized rock in an 18-kilometer-long syncline. The rocks that host these ore bodies and the associated mineralized areas occur today as roof pendants in granitoid rocks of Pennian age that were emplaced during a continent-to-continent collision during that period.

Jan 1, 1991

By Francisco J. Sotillo

Using new ecological-natural-organic depressant for gangue and pyrite with antibacterial properties (control of acid mine drainage) with new improved xanthate collectors using rheology additive not chemical reacting with xanthate resulted in better sulfide flotation. Rougher-scavenger lead flotation tests were conducted increasing the concentrate grade from 7.07% Pb to 13.44% Pb, enhancing selectivity. Lead recovery increased from 64.08% to 79.38% and 80.40% using only the new depressant, and improved xanthate Z-11 and Z-4, respectively. The results demonstrated that the new depressant was selective and efficient, and the new improved xanthates stronger more selective collectors.

Feb 22, 2026

By E. S. Cheney

The sandstone-type uranium deposits of the Gas Hills occur in the arkosic, lower Eocene Wind River formation on the southern edge of the Wind River Basin. The d S34 values of pyrite cement associated with uranium mineralization are-significantly lighter than values for syngenetic-diagenetic pyrite nodules, therefore the H2S responsible for the precipitation of the epigenetic pyrite and uraninite was produced [t]epigenetically. These values are much lighter than the values of H2S from neighboring oil fields. The presence of biogenic pyrite in meta-igneous Precambrian cobbles indicates that these cobbles are not remnants of former; vein-type uranium deposits.

Jan 1, 1964

By Malcolm J. Lake, P. Brad Marchant, Linda M. Broughton

Thiourea is recognized as a technically competitive alternative to cyanide for gold and silver extraction for a variety of ores and concentrates. This paper describes the results of a recent mini-pilot locked cycle test comparing cyanidation with acidothioureation treatment of gold bearing sulphide concentrate. The gold extractability of both methods was similar. The comparative metallurgical operating conditions and test results are summarized. Detailed byproduct solution analyses and environmental toxicity test results are presented and suggest that thioureation might result in acutely toxic byproducts even after treatment. Comparative process economics are summarized based on preliminary commercial operating flowsheets derived for the locked cycle case study. Capital and operating cost estimates are shown. The results indicate that cyanidation is more economically favorable within the constraints of the case study. Considerations for process selection between thioureation and cyanidation, for conceptual case studies, are discussed.

Jan 1, 1998

By Donald M. Hausen

Microscopic evaluation of trace quantities of metalliferous phases in flotation products requires counting large numbers of particles. Particle counts of many thousands may be required for precision, but not obtained practically by conventional microscopic techniques. A less tedious microscopic method for evaluating trace sulfides in mill tailings was developed for the O'okiep Mining Company in South Africa. Hundreds of thousands of particles were evaluated by this method called "gross-counting." Gross-counting consists of counting microscopic fields rather than point-counting individual particles. Total counts are calculated by multiplying the average number of particles per field by the total number of fields examined over the entire mount. Total gross-counts range from about 20,000 particles for +200 to 100,000 or more for -400 mesh size material in lucite mounts. Sulfides and metallic particles in each field are identified and tallied along with field counts. Totals for each type of metallic particle are divided by the total gross-count to give volume percent which is corrected to weight percent by specific gravity factors.

Jan 1, 1969

By Wolfgang Pietsch

DR iron') is a generic term for metallized product that results from the direct or solid state reduction of iron ore. In direct reduction, iron oxides are reduced to metallic iron in the solid state without an intermediate melting step. MIDREX ® Iron is the DR iron material produced in the MIDREX ® Direct Reduction Process. Except for some thermal and mechanical degradation, the external physical form of as-reduced DR iron is the same as the feed material. Chemically, oxygen associated with iron is removed leaving a very porous structure. Figure 1 is the scanning electron micrograph (SEM) of the internal surface of a MIDREX Iron pellet obtained from a Swedish oxide pellet during reduction at 760 °C. Figure 2 is the SEM of a polished and etched cross-section through the same pellet showing the amount of intraparticle porosity. As a result of this high porosity, apparent density of DR iron is relatively low, typically a¬round 2 g/cm3, and specific surface is extremely high, typically around 1.0 m2/g or more. Both density and specific surface depend on the raw materi¬al and the operating conditions of the direct reduction plant. Normally, more than 97% of the available iron is reduced into metallic iron with the rest mainly in the form of wustite (FeO). During direct reduction, the gangue in the iron remains essentially unchanged. Removal of oxygen and the corre¬sponding reduction in weight result in a slightly higher percentage gangue in the product than in the raw material.

Jan 1, 1976

By Madan M. Singh

Section 516 of Public Law (PL) 95-87, commonly known as the Surface Mining Control and Reclamation Act of 1977 (SMCRA), requires that underground coal mine operators must "adopt measures consistent with known technology in order to prevent subsidence causing material damage to the extent technologically and economically feasible, maximize mine stability, and maintain the value and reasonable foreseeable use of such surface lands, except in those instances where the mining technology used requires planned subsidence in a predictable and controlled manner..." Implied in the constraints of Section 516(b)(1) of SMCRA is a determination of what constitutes "material damage" to surface structures, renewable resource lands, and the capacity for sequential land use following underground mining. The authors have already briefly addressed the subject of damage criteria in relation to surface structures (Bhattacharya et al, 1984). In this paper, an attempt is made to provide quantitative guidelines to ascertain material damage to renewable resource lands, although the data available to establish these criteria are considerably more limited than is the case for surface structures. Besides, many more variables influence the severity of the impact at a given site, making the task of assigning stringent ground movement limits even more complex. This often necessitated use of professional judgement and occasional reverting to a qualitative approach. Hence the reader is cautioned at the very outset that the quantitative limits presented herein are approximate and are primarily intended to serve as rough guides for ascertaining the extent of damage to the renewable resource lands under consideration, and that depending on site-specific conditions the actual damage incurred may differ significantly from that predicted by the proposed criteria. The authors, however, feel that the criteria suggested are somewhat conservative, but realistic. The actual damage observed should generally be less severe than predicted by these criteria. It may also be clarified here that the term "subsidence", as used in this paper, implies the total phenomenon of surface and subsurface effects associated with the mining of minerals and not only the vertical displacement of the surface as is sometimes inferred in the literature.

Jan 1, 1984

By Christopher Mark

Successful longwall gate entry design requires control of both vertical and horizontal stresses. Vertical, or overburden, stresses are most severe in the tailgate where they are concentrated by longwall panel extraction. Horizontal stresses, which are generally tectonic in origin, can be highly destructive during the development and headgate phases of longwall mining. The goal of this paper is to present the current state-of-the-art in detecting and controlling horizontal stresses. The information presented was collected through site investigations at 45 U.S. longwalls and an international literature review. The paper begins with a discussion of the present knowledge of regional in situ stress fields in the U.S. A review of available underground stress measurements from coal mines is presented, along with data collected by structural and petroleum geologists. The combined evidence indicates that a persistent ENE-EW trending stressfield is present throughout the eastern coalfields. Experience with horizontal stress in longwall mines is addressed next. The paper focuses on the northern Appalachian region, where the effects of horizontal stress have been most evident. Three case histories are discussed in detail, and the solutions each developed are highlighted. Observations made in the Southern Appalachian, Alabama, and Illinois coalfields are also described.

Jan 1, 1991

By William O. Rasmussen

Exploration requires processing highly varying kinds and amounts of geologic information. Successful discovery dictates that this be done quickly with maximum confidence. Most phases of exploration are more or less applicable to computer reduction on a routine basis. The use of digital computers to reduce raw data into interpretable form, lets the exploration geophysicist concentrate on interpretation and presentation, and to consistently apply more sophisticated and comprehensive analytical techniques, not practical before. In applying these concepts for the past several years, various efficient programs have evolved which provide more complete evaluation of all data including the pro- vision for more unique solutions. This has resulted in greater refinement and ability to select the most advantageous drill sites in a minimum time at a minimum cost or, in rejecting as soon as possible a project on which additional effort is no longer justified. Practical examples of computer applications in magnetics (air and ground), induced polarization and resistivity are discussed.

Jan 1, 1969

By S. P. Hansen

Gravity sedimentation is one of the most widely used processes for separating solids from liquids whether it be for ore and mineral processing or for treating municipal sewage or industrial wastes. Investment in sedimentation equipment can represent a significant portion of the total capital costs associated with a processing or treatment facility. In spite of the importance of sedimentation, little attention has been devoted in recent years to improving this equipment by applying the basic principles involved in sedimentation. In the water and waste treatment field, design criteria established one half-century ago is still the accepted standard and in reflection of this lack of progress, sedimentation and thickening equipment has remained virtually unchanged. The primary purpose of this paper is to present and describe a new innovation in gravity sedimentation which has been applied to water and wastewater treatment and could definitely have application in the field of ore and mineral classification. A secondary object is to introduce the mixed media filter which has been widely used to treat municipal drinking supplies, industrial process water and to provide tertiary treatment of sewage and industrial wastes. The tube-type clarifier was developed primarily to be applied in the field of water and waste treatment where it was found that it could be used to considerably reduce the size and cost of clarification facilities. A logical extension of the tube clarifier would be to the area of minerals classification, ore separation, and for treating waste water associated with these activities. In water treatment practice, most clarification processes are followed by a filtration step to provide further polishing of the water prior to use. This paper will also discuss the mixed media filter which is graded from coarse to fine in the direction of filtration and is capable of operating at high filtration rates and with greater applied suspended solids loading than other filter designs while providing a high qualify filtrate.

Jan 1, 1970

By Stephen D. Schwochow

Aggregate producers nationwide well recognize the numerous problems often faced in securing local approval to open and operate new gravel pits and rock quarries. Similar problems are faced in Colorado, but this region also presents certain political, social, and geological complexities that have become particularly troublesome in the last 10 years. The gravity of the local permitting dilemma can be related directly to the worsening supply-demand imbalance for aggregates in the state's most populated area, the Front Range urban corridor, particularly the Denver metropolitan area. The drive to develop crushed-rock reserves to supplement dwindling alluvial supplies and to meet increasing regional growth demands was somewhat predictable but perhaps more a "last resort" alternative forced onto producers by a hesitant and often apathetic government.

Jan 1, 1982

By Sakshi Hazuria Anderson, Angela Binder, Oscar Jaime Restrepo Baena, Simit Raval, Sandra Nowosad

As the mining industry faces times of change, new challenges arise to ensure raw material supply for future generations. Different scenarios are currently shaping the way we mine and teach mining engineering. Led by an increasing demand for raw materials, net-zero requirements for improving long-term operation performance, technological advancements such as automation and digitalization, safety improvements, environmental considerations and a need for social acceptance, mining is pursuing to change and adapt to these requirements at a faster pace. Such changing times raise new concerns, one of the most relevant is the lower number of students interested or enrolling in mining engineering and related fields, leaving mining engineering as one of the less preferred career options for students. Nonetheless, it is essential to continue addressing and supplying the skill sets that are suited to the contemporary and future mining industry. To this end, globally, academia is currently undergoing several initiatives such as curricula updates and adaptation, upskilling, improving teaching practices and techniques, including e-learning techniques, enhancing industry-academia and inter-university collaboration, and much more. In countries like Australia, where mining plays a crucial role in the economy, the need for curriculum updates is more pressing than ever. As the mining industry evolves with new technologies and sustainable practices, there is a growing demand for a workforce skilled in these modern approaches. Recognizing this necessity, universities such as the University of New South Wales and Curtin University have taken significant steps to revamp their educational programs. By updating their academic offerings, both universities aim to equip graduates with the necessary skills to drive innovation and sustainability in mining, supporting Australia’s development as a leader in this critical sector. Moreover, the selection of topics that drive curricula update and the focus of the research institutions in mining engineering must extend beyond mere technological and technical aspects to include social and ethical dimensions. In this context, the Universidad Nacional de Colombia, in association with the Colorado School of Mines, has introduced the topic of humanitarian engineering (HE) in 2020. HE is a sociotechnical approach that focuses on developing engineering solutions that promote the sustainable development of communities addressing their basic needs and aiming to improve their quality of life (Menéndez-Aguado et al., 2023; Smith et al., 2023). By focusing on sustainable development, community engagement and equitable resource distribution, HE helps the industry build positive relationships with stakeholders, reduce conflicts and foster social license to operate. As the mining industry seeks sustainable and socially responsible practices, future engineers require training in this area to understand the broader impacts of their work, fostering a mindset that prioritizes community well-being and environmental stewardship alongside technical proficiency. However, developing skills toward humanitarian engineering and sustainable mining among new generations of mining professionals remains a complex task. Integrating the necessary content to prepare future engineers for the multifaceted demands of the industry into a single study program poses significant challenges. To address these complexities, modern educational approaches such as the ones integrated in the mining engineering programs at Clausthal University of Technology can be leveraged to enhance both teaching and learning experiences (Binder, 2024b; Bothe-Fiekert et al., 2023; Nowosad et al., 2024). Innovative teaching methods, such as blended-learning, project-based learning, case studies, scenario simulations and interdisciplinary collaborations, can help bridge gaps by fostering critical thinking, creativity and empathy among students. By embracing modern pedagogical strategies, institutions can better equip future engineers to navigate the evolving landscape of the mining industry responsibly and effectively.

Dec 1, 2025