Search Documents

By W. C. Baver

Even before the energy crisis developed in the early '70's, considerable research world-wide was being directed towards the development of schemes to both reduce the energy requirements and to reduce air pollution emissions associated with the manufacture of glass. In many cases the sought-for solutions would benefit both objectives. If, for example, the glass batch could be consolidated into such compact forms as briquettes or pellets, they could be preheated in a moving-bed heat exchanger with the high-temperature exhaust gases from the glass furnace. Lower furnace temperatures would thus be possible with a corresponding reduction in heat losses and total fuel consumption. Moreover, the lower temperatures would also reduce the amount of nitrogen oxides generated in the furnace and emitted to the atmosphere. Many tests on consolidated glass batch have been run in many countries. In some cases, extended tests on production furnaces have also been included in the programs. For various reasons, however, none of these has proved to be economically attractive. The current, but temporary lull in the rapidly rising cost of energy which has been with us in recent years, has reduced the push for research for energy saving means for melting glass. A few of the current programs will be discussed. Since raw material requirements, primarily physical in nature, are affected by some of these schemes, these will also be considered.

Jan 1, 1986

By Roy Norcross

For the past few years Caro's acid has been used for the treatment of cyanide containing slurry effluents, providing a feasible alter­ naive to other slurry treatment processes including !NCO SO2 / Arr and ferrous sulfate. Presently, mines using Caro's acid gen­erate their own Caro's acid onsite making a relatively low quali­ty product. It was at this point where we, at Degussa Corporation, decided to focus our efforts on engineering a Caro's acid genera­tor capable of cost effectively producing a high quality Caro's acid solution, thus reducing operating costs significantly. Caro's acid or peroxymonosulfuric acid is not a new chem­ical nor is it new to Degussa. The product was named after Heinrich Caro (1834-1910), a German chemist who first described its synthesis and its oxidizing properties in 1898. Degussa has been producing the potassium salt of Caro's acid as the triple salt, 2KHSO5 - 2KHSO4 - K2SO4, called Caroat®, for over 30 years. Caroat® is used for household and denture cleansers, as a bleaching agent in dish washing detergents, in printed circuit board etching and for cyanide destruction in the plating industry. From our experience in producing Caroat® Degussa developed its new Caro's acid based DegOX™ technology for the treat­ment of cyanide containing effluents from gold and silver mines.

Jan 1, 1996

In conjunction with steady increases in production levels, long-wall operators have applied greater quantities of ventilating air to control respirable dust and methane gas. As a result, air velocities greater than 7.6 m/s (1500 fpm) have been measured on longwall faces. Operators have expressed concern over the potential entrainment of respirable dust at these high-velocities, especially during shield advance as dust falls from the shield canopy directly into theair stream. Laboratory tests to simulate dust liberation by shield movement were conducted at the Pittsburgh Research Laboratory of NIOSH in a wind tunnel designed to study dust entrainment in high-velocity airstreams. Dust was introduced into the tunnel to determine dust concentration as it relates to entrainment, dilution, air velocity, and particle adhesion. Airborne dust samples were obtained by iso-kinetic sampling using BGI cyclones to quantify respirable dust concentration at the various air velocities. Laboratory tests were con-ducted at velocities ranging from 2.0 to 10.1 m/s (400 to 2000 fpm),and significant differences in airborne respirable dust levels were measured. This research is being conducted to provide fundamental information on the entrainment characteristics of respirable dust at high air velocities, which will subsequently lead to solutions for shield dust control. A discussion of the test procedures and results are presented.

Jan 1, 2004

By Vi-Duong Dang

Lithium requirements in the next few decades for batteries and controlled thermonuclear fusion reactors (CTR) may exceed the availability of the current mineral and brine reserves. It is thus prudent to search for new reserves and resources to satisfy these and future lithium applications. The lithium content of the waters from the Smackover oil field. located in the Gulf Coast region of the United States, ranges from 100 to 500 mp/l and could represent a substantial new reserve. Experimental evidence described in the literature indicates that a specific chelating agent dipivaloylmethane (DPM), of the diketone type, has a specific selectivity toward lithium in the presence of other metal ions in aqueous solutions. Based in part on this unique property of dipivaloylmethane, a conceptual design of a full-size plant to extract lithium from the Smackover brine is presented in this paper. This study includes alternate flow-sheet development, design information on the major units of the process, energy requirements, and an economic analysis of a facility capable of producing 106 kg of lithium per year. The economics of three different process concepts depend primarily on the amount of water needing to be evaporated from the initial oil-field feed waters in concentrating the brine. The results, as a function of production rates, are indicated only in a general manner.

Jan 1, 1978

By Ning Liu, Di Yin, Xuming Wang, Yongqiang Lu, Jan D. Miller

Air-sparged hydrocyclone (ASH) flotation technology has been evaluated for phosphate recovery from the central Florida phosphate deposits. As expected, it was demonstrated in pilot-plant tests that the ASH system has a specific capacity about 50-100 times higher than that of a traditional flotation cell. In the case of fatty acid flotation, single-stage ASH flotation produced a recovery of 75-77% in a rougher concentrate containing 24% P2O5 In reverse flotation with amine, the single- stage ASH system produced a phosphate recovery of 98% in a cleaner concentrate containing 31% P2O5. These results are comparable with those obtained at plant operations in the Florida phosphate industry. Based on these pilot-plant results, the effects of process variables are discussed in terms of separation efficiency. Subsequently, a 6-inch ASH system was fabricated and tested in a central Florida phosphate plant for reverse flotation in the amine flotation circuit. The high capacity of the ASH system was again demonstrated for the 6-inch ASH system. A single-stage phosphate recovery of 91% was achieved with a concentrate grade of 30% P205. During plant tests, it was established that porous tube plugging, the most significant engineering problem identified, was due to the poor quality of the plant water. Possible solutions to this problem are discussed.

Jan 1, 1999

By Tae-kyeong Yeu, Cheon-Hong Min, Hyung-woo Kim, Sup Hong, Minuk Lee, Chang-Ho Lee

This paper concerns the optimum arrangement of the buoyancy module, which is used for stable dynamic motion and structure stability of the marine flexible riser. The main method of this study is simulation-based design using Genetic Algorithm (G.A) for optimum design and Multi-body dynamic for simulation. The marine riser connects the vessel and the seabed-tracked vehicle. The motion of the riser affects the motion of the vessel and the vehicle. In this study, a marine riser of the deep-seabed integrated mining system (Figure 1) is used. This riser has a strong effect on efficient transfer of minerals. So, the buoyancy module must be equipped to supplement problems of the structure stability and the dynamic motion. Positions and quantities of the equipping buoyancy modules are determined by the at sea experiment (Figure 2). But this method is not easy because the actual sea experiment is expensive, time-consuming and dangerous (Figure 3). Thus, the position and quantity must be determined by simulation-based design. The dynamic analysis models of the riser and the buoyancy module were built in the commercial software DAFUL. In the marine environment, factors affecting behavior are current, drag force, etc.

Sep 1, 2014

There is wide agreement that sustainability has multiple dimensions, but substantially less agreement on the appropriate balance among those dimensions. This occurs because peoples’ vision of a sustainable future, their goals for sustainable development, and their objectives for resource management are reflections of their values, culture, and life experiences. Even assuming agreement about the objectives of sustainable resource management can be reached; there is still a need for policy and decision makers to choose from among alternative courses of action, each of which has its own set of impacts and outcomes. One of several tools used to compare the consequences of alternative actions is the Computable General Equilibrium (CGE) model. This paper uses CGE modeling to demonstrate how policy decisions do not take place in a vacuum and how policy-makers must be aware that there are trade-offs involved in any decision.

Jan 1, 2005

By B. C. Bhowmick, B. B. Dhar

Central system of ventilation, adopted almost universally in coal mines of India and elsewhere in the world, has often proved deficent in providing a cost effective solution to the acute ventilation problems of remote workings in many mines. Loss of air due to leakage through a number of stoppings, doors etc. and accumulation of heat and moisture by intake air on its way to a working through long and circuitous route are the main unavoidable reasons for low efficiency of the system, sluggish and oppressive ventilation of workings. Multi-zonal ventilation system using large diameter bore holes for feeding fresh air in the mine close to a working has been proposed as a viable economic alternative. The method promises to provide congenial environment at working faces without resorting to air conditioning or use of booster fan. Optimum location and diameter of bore holes as well as general design procedure have been dealt in the paper. Finally, the technical as well as economic advantages of the method over the conventional design have been highlighted with the help of a case study where ventilation system of an extensive shallow mine in Central India has been redesigned according to the old and the new concepts. The methodology is general enough for adoption elsewhere in other mines under similar circumstances.

Jan 1, 1993

By Ralph H. Knode, Stephen P. Collings

INTRODUCTION The Crow Butte uranium deposit is located in northwest Nebraska near the town of Crawford (Figure 1). The deposit was discovered during the fall of 1980 by Wyoming Fuel Company, operator of the Crow Butte Joint Venture. The Crow Butte Joint Venture is owned 50 percent by Wyoming Fuel Company, a subsidiary of KN Energy, Inc.; formerly Kansas-Nebraska Natural Gas Company, Inc., 40 percent by Ferret Exploration Company, Inc., and 10 percent by First Exploration Company. A preliminary announcement made in January 1981 indicated a "probable potential" reserve in excess of 25,000, 000 pounds U303. Drilling during 1981 and 1982 confirmed these reserves and indicated the presence of more than 30,000,000 pounds U308 having an average grade in excess of 0.25 percent U308. Wyoming Fuel Company was initially attracted to the area in 1978 by favorable regional geology for sandstone uranium deposits and weak radioactivity noted in regional oil and gas holes. Exploration drilling began in 1979 following the formation of the Crow 3utte Joint Venture. Drilling has continued up to the present, at which time the Joint Venture is ready to proceed with a pilot scale solution mine. Environmental baseline data have been acquired and the permit applications for the pilot scale mine have been submitted to the Nuclear Regulatory Commission and to the applicable state agencies in Nebraska.

Jan 1, 1984

By D. B. Stephens

Milling operations throughout the world have created vast amounts of waste by-products, or tailings, which are often disposed on the land surface. The wastes may be disposed behind dams, on untreated ground, or on compacted clay or synthetic liners of impoundments and trenches. Often one of the principle concerns of environmental regulatory agencies is whether seepage from the waste pile could move through the vadose zone to the water table and possibly contaminate an aquifer. The seepage may be generated by the drainage of liquids initially deposited along with the tailings or by infiltrating meteoric water which leaches solutes from the tailings. The purpose of this article is to discuss some of the commonly held assumptions regarding storage of seepage wastes in the unsaturated zone. The significance of recent studies of water movement in dry climates which pertain to tailings site selection will be presented. The paper is relevant not only to seepage from impoundments at mill sites, but to many other fluid waste impoundments as well in part this article reinforces earlier work by Stephens and Siegel (1980) and an excellent review paper by McWhorter (1985). The present report addresses considerations in porous media; for a discussion of the effects of fractures and anisotropy in the unsaturated-zone, refer to the paper by McWhorter (1985).

Jan 1, 1985

By Brian Fulcher, Michael Bell, Shimi Tzobery, Werner Burger, John Bednarski

The Arrowhead Tunnels Project represents the final portion of a 70 km (44-mile) long water conveyance facility that will bring up to 28 m3/sec (1,000 ft3/sec) of water into Southern California. The 13 km (8-mile) tunneling project is well underway and consists of two, 5.8 m (19-foot) diameter TBM bores through extremely variable geological conditions. The tunnels lie near the base of the San Bernardino Mountains and several significant faults including the San Andreas Fault run within one kilometer (0.6 miles) of the tunnel alignment. Numerous other significant faults cross the tunnel alignment and water pressures in the tunnel have been recorded as high as 20 bar (300 psi). This paper describes some of the problems and challenges encountered and the solutions implemented to advance the two hybrid TBMs under conditions that ranged from hard rock with no water inflows to full-face granular material under 10-bar pressure and in excess of 32 l/sec (500 gpm) inflows. Due to the range and severity of ground and water conditions actually encountered, the Owner-Contractor-Designer team eventually found that adjusting the means and methods to be more responsive—virtually on a day-by-day basis—was needed to suit the conditions

Jan 1, 2007

By John A. Breslin

The year 2010 will mark the 100th anniversary of the beginning of the research efforts by the U.S. government to improve the health and safety of miners working in the United States. This research began in 1910 with the establishment of the U.S. Bureau of Mines (the Bureau) and it has continued during the past 10 decades, even after the closure of the Bureau in 1996. The research on safer mining technology, formerly done by the Bureau, has now been combined with National Institute for Occupational Safety and Health (NIOSH) studies of miners? health to form a unified federal research program to improve the health and safety of miners. This article describes this research and places some of the accomplishments into perspective with other activities in the U.S. Mine Safety and Health Time Line (insert).

Jan 1, 2010

By Wayne Green

The Regional Municipality of York, located north of the City of Toronto in Ontario, Canada, has experienced unprecedented growth during the past decade, with new home construction averaging 15,000 units per year. This rate of growth is planned to continue well into the future with a projected growth of more than 500,000 new residents by 2031, combined with a tar-get of more than 300,000 new jobs to provide a sustainable economic base for the region. It should be noted that York region has been designated as one of the key growth centers by the province of Ontario, aimed in part to meet the housing and employment needs of Canada?s growing population. York Region is a mix of urban and rural areas and is one of the most desirable areas to live in Southern Ontario. York region offers an attractive lifestyle, with its nine municipalities and the amenities created by the many rivers, streams and protected greenbelt areas that encompass more than 69 per cent of the region?s area.

Jan 1, 2010

St. Peter sandstone is very different from the minerals and rocks that have been studied extensively in mining. On the one hand, it is brittle as characterized by an unusually high friction angle and steeply curved failure envelopes. On the other hand, it is friable, possessing extremely low, and in most cases zero cohesion. The scarcity of the ground control techniques for this particular mining environment has created many difficulties for the mine operators. In order to resolve these problems, the geotechnical properties of the St. Peter sandstones were investigated through a comprehensive research program, which included uniaxial test, triaxial test, porosity test, thin section, X-ray diffraction (XRD), and scanning electron microscope (SEM). The specimens used for the uniaxial and triaxial tests were specially prepared because of the highly friable nature of the St. Peter sandstone. Thin section, XRD and SEM were utilized to examine the effect of the microstructure of the St. Peter sandstones on its strength characteristics.

Feb 27, 2013

By William Wargo

The basic reason for lining underground cavities is to keep the cavity open during its useful life by providing adequately for the support of the surrounding rock and for the necessary degree of water tightness. This covers the entire field of support methods from the simpliest timber support to reinforced concrete in all its variations as applied to tunnels, galleries or shafts. The problem involved in the design of more efficient and economical lining systems for even bigger cavities has been magnified by increased speed of advance made possible by better blasting tecniques, improved tunneling machines and more efficient material handling. Tunnel lining today requires a disproportionate amount of time and money compared to other operations mostly due to the manuel labor involved in its installation. One solution to this problem is the developement of an entirely new concept in tunnel lining designed notoonly to overcome this bottleneck but also to open up the field for further increases in speed of advance. This new lining system acts first as a fast protective armour then becomes the concrete metal form and ends up as reinforcement sheet inside the concrete lining. This system developed and manufactured by Bernold A. G. of Switzerland since October 1968 has been installed in 25 applications in Europe under all ground conditions from stable rock to unconsolidated ground.

Jan 1, 1970

By Steve Kral

After years of cutbacks, closures and layoffs, the mining industry is beginning to expand again. Metals prices are up and so is investor interest and confidence in the industry. Gold prices began to slowly move up in January2003 and finally cracked the $12.86/g ($400/oz) mark in early December. Silver, too, is up, as is copper. So the mining industry is feeling good about itself again and many companies are expanding existing mines and developing new ones. One side benefit to mining’s improved outlook is that companies are beginning to send more of their employees to industry conferences. Such was the case at the109th Northwest Mining Association meeting in Spokane, WA. The meeting was held in early December and attracted 1,100 attendees and 84 exhibiting companies. That is up from 2002’s attendance of about 900 people and 65 exhibitors. The theme was “A Partnership into the Future.”

Jan 1, 2004

By C. M. Bartley

In world-wide mining circles countries become known by the principal minerals they produce. The production of iron, copper, phosphate and sulphur in the United-States-has-been particularly significant and has provided the base for aggressive developments in heavy industry, agriculture and chemicals. Mention diamonds and gold-and you will think--South Africa; silver-Mexico; nickel and asbestos--Canada. The main purpose of this paper is to point out that potash mast be added to the list of minerals by which Canada is known in the mining World. The potash deposits of western Canada must be classed as a major world source of chemical fertilizer raw material. We believe that they are both the largest and the richest of all known deposits in the world. The most knowledgeable people in the industry avoid making estimates of reserves because even where the arithmetic is correct the total is so large that it appears to be ridiculous. In 1957 Marion Goudie made a carefully qualified estimate of 6 billion tons of recoverable potash above 3,500 ft, and grading 25 per cent K20 or better. This figure can now be increased by the amounts available through solution mining. No one has bothered to estimate how much this is because it is so large that the actual amount is not significant.

Jan 1, 1966

By Steve Kral

In a lagging economy where profits are tight, businesses cut costs. No revelation there. The mining industry, though, has always looked for ways to reduce production costs — no matter the state of the economy or commodity prices. The fact is, when planning a new mine or the expansion of an existing one, mining companies gamble that commodity prices will be reasonably high when a project comes onstream. It takes millions of dollars and several years to bring a mine into operation. And a lot can happen economically between the time management gives the go-ahead for a new project and its completion.

Jan 1, 2002

This paper presents a virtual prototype for the stress analysis of cable shovel components based on combination of flexible and rigid body approach. The general mechanical system of the cable shovel is modeled as a multi-body system with rigid and flexible bodies. The relevant theories applied for the dynamic model are described in terms of Lagrangian multi-body dynamics and finite element method. A virtual prototype of the cable shovel is built in the Automatic Dynamic Analysis Mechanical System (ADAMS) environment, which allows visualizing the motion of general mechanical system and analyzing the dynamic stress of structural components of the cable shovel. An example is given to perform dynamic stress of durability analysis for the boom and handle. Attention of this study is devoted to the mechanisms of damage of the cable shovel and also the critical high stress areas. Keywords: Cable shovel, Von Mises stress, Virtual prototype simulation, Stress virtualization.

Jan 1, 2009

By Kanhaiya Mishra, Phanil. K. Mandal, S. K. Behera, P. S. Paul, Prashant Singh, C. N. Ghosh

The techno-economic and social benefits of cemented paste backfill (CPB) resulted in its wide acceptance by the mining industry. The Ordinary Portland Cement (OPC) remains the key binder but to diminish its economical constraints, suitability of alternate binders has been examined worldwide. The present study aimed to investigate the effect of partial replacement of OPC with fly ash on the CPB’s strength and to determine the most optimal mix to achieve the required strength (1 MPa at 28 days of curing) at the most cost-effective way using the Bayesian network (BN). The CPB mixes were prepared at 72 wt.% solid concentration with mill tailings (87–91%), OPC (6–13%), and fly ash (0–4%), and instantly after mixing, fresh (slump, bleeding, density) CPB properties were measured. The strength was tested at 7, 14, 28, and 56 days of curing and initially analysed through traditional model. The traditional models follow the aleatory principle and are considered not appropriate for geotechnical engineering. Hence, the BN model was developed and tested. The reliability of two classifiers in learning model structure was compared which gives Naïve Bayes as the highest reliable tool. The CPB’s strength is most sensitive to the OPC content. The most consistent mix(s) is mill tailings: 87–88%, OPC: 9–11%, fly ash: 1–4%. Adding fly ash at 89–91wt% mill tailings possesses high failure probability of the CPB. The collinearity test indicates that the fines percentage and chemical composition of CPB’s ingredients are highly correlated with its slump, bleeding, and strength development.

Jul 14, 2022