Search Documents

By Fritz Kleiner, Walter Meintrup

On Nov. 4, 1981 A/S Sydvaranger's 1-kt/h (1,100-stph) wet-process, iron ore ball mill completed its first four months of uninterrupted, full-load operation in Kirkenes, Norway. This 6.5-m-diam (21-ft-diam) mill is driven by a gearless ring or wraparound 8.1-MW (10,860-hp) motor at 13.1 rpm-a first of a kind in this segment of industry. This article examines reasons for selecting this type of drive over more conventional schemes, lists specific advantages of such large mills, and describes the installation in Norway. History For almost a decade, good operating experiences have been gained with 28 gearless ring motor drives in the cement industry, driving 2.5 to 4-m-diam (8.2 to 13-ft-diam) tube mills with drive powers ranging from about 3-4 MW (4,000 - 8,000 hp). Why then did the mineral ore processing industry hesitate until 1980 to adopt this successful concept for similar applications on ball, semiautogenous, and autogenous mills? There are a number of good reasons in the eyes of conservative mill builders and operators, the most commonly cited ones are: • No operating experience in this segment of specialized industry. • More severe environmental conditions in the wet ore grinding process. • An indifferent attitude of mill builders and electric motor manufacturers towards new drive technologies. • Limited confidence in solid-state power supply systems, such as frequency converters of the required size. There have been and still are numerous problems associated with low-speed geared mill drives of any kind, especially with individual motor/gear sizes approaching or exceeding about 4 MW (5,360 hp). Every mill builder knows about them, but operators learn to accept them as inevitable. The Decision to Change Three things combined to break this technological stalemate: the courage and progressive spirit of one major iron ore processor in Scandinavia, the cooperation of three experienced manufacturers, and an unusual application problem that could not be solved by any conventional approach. The last factor was surely the decisive one, but the first one does not come as a surprise either. The Swedes near Kiruna and the Norwegians around Kirkenes are experienced ore miners and processors, and much credit goes to them for technological breakthroughs in the industry. At A/S Sydvaranger in Kirkenes, above the Polar circle at about the latitude of Alaska's northern tip, the existing grinding facilities, with a total of 14 100 to 240-t/h (110 to 264-stph) ball mills, can not be expanded. Nevertheless, to increase mill throughput, only installing a larger mill in place of an existing smaller one was a practical alternative. For this replacement, the owners set requirements that seemed impossible to meet: • The old 100-t/h (110-stph) ball mill should be replaced with a new ball mill with 10 times the rated throughput, without significantly impairing the operation of the remaining mills, and without significantly changing the mill building. • The new mill should have a variable-speed drive to ultimately optimize the grinding process by means of a closed-loop process¬computer-controlled grinding cycle, and to minimize the specific energy consumption. • Availability, efficiency, and life expectancy of all new components must be higher than those being replaced. • Inrush-current and harmonic loads on the rather weak electric supply line must be minimized to ensure safe plant operation. All old ball mills at A/S Sydvaranger are the geared type, using single synchronous and wound-rotor, slow-speed motors with ring-and-pinion gears. Operators are familiar with the limitations and problems associated with such drives, and they are aware that the following items become major concerns when drive powers are drastically increased: • Gears are subject to wear and tear, require frequent maintenance, and eventual replacement of major parts. • Gears are sensitive to misalignment, overload, and thermal distortion, limiting their useful life. • On dual or quadruple drives, load-sharing and torque oscillations between motors can be a major reason for concern. • At these speeds, ring-and-pinion gears reach their torque transmission capabilities altogether at around 4 MW (5,360 hp) per motor/pinion. To obtain the desired variable-speed performance of the new drive, the only practical and economical conventional solution would have been a frequency-controlled, low- or medium-speed dual motor drive with about 8 MW (10,720 hp) of power. This, however, was not feasible because of limited floor space. Therefore, bids were solicited for the alternative drive method, the gearless ring motor. General Considerations Why are such large mills considered? After all, one could avoid all the problems by simply staying with smaller mill unit sizes. Under competitive pressures of free markets, however, grinding efficiencies and specific energy consumption become key factors in selecting new equipment. Specific energy consumption of ball mills decreases with increas-

Jan 9, 1982

By E. A. Rychkun

Introduction Minicomputers have been gaining acceptance in mining. Low cost interactive processing and plotting can now be controlled by geologists or engineers needing rapid solutions and specialized mining software in formats that allow noncomputer personnel to readily interact with computer processes. User-oriented programs maximize the use of interactive display features and graphics, as shown by the HP9845 minicomputer, a unit with portability, processing power, graphics capabilities, capacity, and peripherals such as plotters, digitizers, disk drives, and printers. Application Coal exploration projects require that much effort be spent determining coal volumes within trial pit limits. This determines a prospect's viability and potential. Adapting volume calculations to a computer has been limited, since it was difficult to create reasonable representations of complex coal seam geometry with a digital process. So many of the simple mechanical procedures needed to produce pit reserves are still performed manually by geologists and engineers. But with new minicomputers and their interactive graphics, it is now practical to accurately model complex structures without tedious calculations. GEOSEM (Geomin Seam Oriented Exploration System) is a computer system designed to analyze coal prospects. The system shows how a coal prospect, with complex geology, can be quickly analyzed, modeled, displayed, and evaluated for mineable reserves. Its interactive graphics allow rapid visual presentation of data, high-speed tabular reports, and precision plotting. The system is most effective when used by a geologist or engineer who selects the required operations and specifies relevant parameters via screen and keyboard interaction. Rolling Hills The Rolling Hills prospect represents a typical Rocky Mountain coal deposit. Enough geological interpretation has been done to show a complex system of block faulting with coal seams following synclines of stratified lithologies. With the completion of initial drill hole exploration, questions arose concerning coal volumes and strip ratios involved with various pit limits. Quality information had been gathered on the coal intercepts. It was decided that coal vol¬umes and pit designs were of prime importance. The objective was to enter and display data, create a computer model based on interpretation, develop pit designs, compute seam/ waste volumes, and report various contents. The project, begun by entering data in the GEOSEM system, was completed in several days. Data Entry For modeling, the prime information was seam identity and drill hole intercept. Other information-rock type, Btu rating, and percent of ash, sulfur, and moisture-was also available. It, too, was entered into the data base through the computer keyboard and then reported, verified, and corrected. Various reports can be produced, according to user specified sort parameters. For example, from an analysis of available data, only 14 intercepts could be found with Btu value greater than 8000 and sulfur content less than 0.4%. The sort option can also be used prior to entry into the analysis routines. Data Analysis Though the objective was to create a seam model and compute reserves, it became necessary to project quality information into unsampled areas. Statistical analysis was then war-ranted. A typical analysis correlated the lack of relationship between percentage of ash and Btu. Although histograms were also produced, these typified a lack of samples and "ragged" distributions. A geostatistical analysis was also applied, showing the results of computing a 2-D variogram on the largest coal seam. Results showed an average range of 18 m, with a poorly defined variogram. Data Display and Drafting Scaled plans and sections were required so seam locations could be compared to hand drawn interpretations and drill coordinates verified. At the same time, topography could be interpolated from collar elevations to determine whether surface control points were needed for better definition. In addition, a new set of 50 final-scale drawings were required, showing new drilling information. By using the computer screen as a "scratch pad" device, various sections were displayed and then plotted on a drum plotter at the desired scale for overlay on original sections. Both lithology and seam name were plotted for the five main sections. Since the coal seams were striking north-south, sec-

Jan 11, 1981

By G. Swartz, R. J. Brison, R. A. Wyman, J. P. Vandenhoeck, S. E. Khalafalla

Magnetic fluids are commonly composed of ultrafine submicron particles of magnetite (Fe3O4) dispersed in either a kerosene or a water carrier medium with oleic acid as a protective colloid. The unique property of these fluids is that when the magnetic particles are attracted to a magnet the carrier medium moves along with the particles so that the liquid also appears magnetic. The availability of a fluid whose gross behavior changes sharply in a magnetic field without affecting its rheologic characteristics is becoming critical for many technologic applications. About two gener¬ations ago suspensions of relatively large, micron-sized ferromagnetic particles in oil proved useful in clutches, brakes, and dashpots. These were called magnetic clutch materials, and their viscosities were highly dependent upon the applied magnetic field, in contrast to true mag¬netic fluids which retain their fluidic characteristics under all applied fields and field gradients. While the term "ferrofluid" was used by Rosensweig and Kaiser&apos; to designate a magnetic colloid composed of a dispersed magnetic ferrous material, the more general term, "mag¬netic fluid," is preferred. This is because these fluids may contain ferro- or ferrimagnetic substances, such as cobalt, nickel, gadolinium, dysprosium, or magnetic ferrites in carrier liquids, such as hydrocar¬bons (kerosene), silicones, water, fluorocarbons, etc. Preparation of Magnetic Fluids Magnetic fluids were first prepared by Papell and Faber, at the NASA Lewis Research Center, Cleveland, Ohio, by tumbling ferrite materials for several weeks in a carrier medium (such as kerosene) and a dispersing agent (such as oleic acid) with steel balls. Rosensweig et al.1 compared the stability of their ferrofluids obtained from both metallic iron and the magnetic oxides of iron, Fe3O4 and yFe2O3. They found that, although the saturation magnetization of iron is 3.5 times greater than that of magnetite, its colloidal solutions deterio¬rated much more rapidly. The iron particles were undoubtedly rapidly oxidized to a nonmagnetic state due to the enormous surface area of these colloidal particles. Because the properties of these fluids are highly dependent on particle size and may acquire opposite characteristics by small incre¬ments in that size, more controllable methods of preparation have been developed recently by Khalafalla and Reimers.6 In one method metastabilized pyrophoric wiistite is ground to colloidal size in a kerosene oleic acid mixture, and then it is disproportionated to colloi¬dal magnetite and iron at temperatures just below the eutectoidal temperature of wüstite stability (570°C); thus, t < 570°C 4 FeO t > 570°C Fe + Fe30, (1) Because of its antiferromagnetic characteristics, the precursor wüstite is much easier to grind than magnetite. Another method3 avoids grinding entirely and utilizes a peptiza¬tion technique from ferrous materials in the molecular state of aggrega¬tion. This latter procedure has resulted in preparation of strong fluids at considerable savings in cost.

Jan 1, 1985

By P. Ollivier

The ore-processing plant of the Soremib mine Pour a (Burkina Faso) has now been in uninterrupted operation for 3 years. Ores from the oxidized and non-oxidized zones of the deposit are processed together in one flotation unit. About 60% of the gold is free and is recovered in a gravity processing unit. The residual gold in the flotation concentrate is processed on the spot by cyanidation and carbon-in-pulp.

Jan 1, 1998

By J. W. Jang

The wear behaviors of grinding media with different chemical compositions and microstructures in wet grinding of a quartz-pyrrhotite mixture was investigated under various environments. The marked ball wear tests showed that the wear rate could be minimized by a suitable combination of martensite and ferrite within the same ball. A ball composed solely of hard martensite exhibited increased wear under an oxygen environment, while balls composed of both soft ferrite together with hard martensite exhibited decreased wear due presumably to the difference in their passivation? behaviors. The galvanic interactions between the two phases as well as among these phases and an electroactive mineral were investigated through electrochemical measurements under abrasive conditions in a slurry. The rates of formation of passive films controlled the corrosion currents of the high chromium steel media. Corrosive wear and its effect on flotation are discussed using the passivation kinetics model thereby developed.

Jan 1, 1989

By E. B. Fitch, D. A. Dahlstrom

Liquid-solids separation is common to practically all mineral and coal processing as the bulk of beneficiation plants employ water as the major processing vehicle. The growing usage of hydrometallurgy has increased the importance of liquid-solid separation as acidic and basic solutions result in greater amounts of colloidal solids, with their consequent greater difficulty of separation, the economic need for chemical recovery to minimize this operating cost, and the usual necessity of employing more costly construction materials. The three processing steps covered in this section have significant capital costs. Drying, particularly, has an important operating cost because of the obvious need for energy to evaporate the water or solvent. Several common factors influence all three liquid-solid separation steps. Particle Size and Size Distribution. In general, finer particles have slower settling and filtration rates. The specific surface area is increased, which means a lower solids concentration in the thickener underflow and discharged filter cake as well as a grater moisture content to be evaporated in the drying step. Therefore, overgrinding or excessive attrition should be avoided. Consideration should be given to optimum particle size consistent with entire plant operation performance and recovery. Solids Concentration. Increased feed solids concentration will generally minimize required equipment size and costs in all three liquid-solid separation steps. Most thickeners are designed on the basis of unit area required, expressed as square feet per short ton of dry solids per day (square meters per metric ton per day) which will usually decrease with increased feed solids concentration. Filtration rates also increase as the required flow through the capillaries of the filter cake decreases. Dryer capacity increases and less energy per ton of final product is required to evaporate the associated moisture. Particle Shape and Surface Characteristics. Generally, optimum shape is a spherical particle of zero porosity. As either of these factors degrade away from the desired state, difficulty increases. This is particularly true in drying, where porosity can decrease drying rate significantly if the moisture must first reach the particle surface by diffusion

Jan 1, 1985

By Peter Bryant

"The case for innovation in the mining industry has never been more compelling—whether you believe the industry is in a sharp dip in a significant ‘sawtooth’ cycle or in the midst of a bust — the imperative is the same. Despite record production levels and still above-average prices compared to the lows of 2000, the industry is struggling to make profits and provide the returns on capital that investors are seeking. This represents a large-scale destruction of value over the last 15 years.The last 10 years have seen a sustained rise of operation expenses and capital development costs while there has been a rapid decline in productivity. This trend is unsustainable especially against other key structural challenges and forces shaping the future of the industry:1. Despite short-term fluctuations, there is longterm sustained demand for commodities.• Demand is driven by relentless urbanization, population growth and a rapidly growing middle class.2. Environmental concerns continue to mount.• Existing mining methods and their environmental footprint are becoming increasingly unacceptable to society.3. Geopolitical pressures and community activism are growing.• An estimated $25 billion worth of projects are on hold due to community activism.• Increasing nationalism tendencies and government expropriations of close to $30 billion.• Social license to operate is being challenged.4. Finding, building, operating and closing a mine just keeps getting harder and more expensive.• Costs have been increasing at an annual rate of 10 to 15 percent for the last 10 years.• More assets are stranded as they become uneconomical to mine under current mining methods, e.g. Olympic Dam.• Ore grades continue to decline.• Declining productivity at an annual rate of more than 10 percent for the last 10 years.5. The industry has consistently underinvested in technology and innovation."

Jan 1, 2015

By N. J. Themelis, W. H. Dresher

Research is probably the least understood and the most underrated or overrated, depending on the circumstances, function of the corporate enterprise. Some companies become engaged in research because they consider it to be vital to their very existence, others in order to develop new business, and some with no clearer objective than to keep up with the competition. Whole new industries have resulted from research activities, such as the Xerox copier, the transistor, the computer, and have affected considerably our way of life. Companies have prospered or perished by pursuing the successes or failures of their research organizations. However. despite the tremendous effect that research has had on our modern civilization and the billions which are spent on it annually, we have not as yet been able to develop many hard and fast rules as to how to conduct it effectively and to a successful end.1 This section discusses the role of research in the United States and in the mineral industry and describes a few of the criteria and guidelines which have been developed to assist in increasing the probability for success in industrial research. Broadly speaking, the purpose of industrial research is to make a significant contribution to the long-term viability and the profitability of the sponsoring company. The sum total of technological developments has been a principal factor in establishing the United States as a world leader and the controlling element in the nation&apos;s balance of trade with foreign powers. The international aspect of most mineral commodities is a significant factor in the business decision-making of most domestic mining companies and should be an important factor in the operation of research and development (R & D) programs in these companies. The National Science Board has reported that in recent yean other nations have been gaining on the United States over practically the entire range of science. 2,3 On the positive side, the NSB reported a strong position for the US in the results derived from its investment in R & D. If the United States is to maintain a favorable trade balance, it must create new know-how through technological innovation in order to create new industrial products, processes, and services for which there is a global demand. As expressed by Chauncey Starr, president of the Electric Power Research Institute, "Unlike resources found in nature, technology is a man-made resource whose abundance can be continuously increased, and whose importance in determining the world&apos;s future is also increasing."&apos; In recent years, the greatly in- creased pressures for environmental quality and energy conservation have enhanced further the role of technical innovation in insuring the future survival of the domestic industry. Technology is the challenge of American industry, and it is a challenge which the mineral industry must also accept, for processed minerals are the very raw materials and energy on which all of industry is based, it is technology which makes a mineral deposit into an ore reserve. The Natural of Industrial R D Research is usually thought of as being either basic or applied. Basic or fundamental research is the quest for knowledge and need not have any practical objective. Applied research is the search for a solution to a particular problem and therefore has a specific objective beyond the acquisition of new knowledge. Development is the next stage to the applied research experimentation and it generally consists of larger-scale tests to establish the technical and economic feasibility of the new process or product and to provide design information for its industrial implementation. The terms research and development are usually interconnected for the good reason that in many cases it is difficult to define where one ends and the other begins. For instance, in many cases, thermodynamic, kinetic, corrosion, and other research studies, which are needed to provide design data for an industrial plant, may prod in parallel with the pilot plant activities preparatory for this plant in order to conserve time. Often the final stages of a development project may involve the trial production of a new product for markeing tests or the trial operation of a new process on a "semi-industrial" scale pilot plant. Such operations may be termed "demonstrations"; hence, more

Jan 1, 1985

By D. J. Brunner, S. Mathur, D. McKinney

With the advent of faster micro-processors, the use of numerical methods to simulate complex fluid dynamic phenomena in three dimensions for use in design has become prevalent in the automotive, and turbo-machinery industries. The Computational Fluid Dynamics (CFD) method divides the region of interest into small control volumes which form the mesh representing the physical characteristics of the problem, and uses the finite volume method to intergrate the equations for the conservation of mass, momentum, energy and species over each control volume. Recent developments in CFD software expedite mesh generation, and enable the use of unstructured grids, comprised of tetrahedral volumes in three dimensions and triangular areas in two. CFD more accurately represents complex geometries and allows for relative movement of meshes enabling simulation of multiple moving bodies. &apos;ibis paper presents two examples of how CFD simulation can be used to assess mine and tunnel ventilation problems formerly addressed by application of analytical solutions which were developed assuming ideal incompressible conditions. CFD simulation is used to evaluate the impact of varying the airflow in a descentionally ventilated airway on the layering along the roof of smoke and hot gases resulting from a vehicle fire. Control of the smoke layer is required to enable safe egress from the vehicle, particularly if the vehicle is for personnel transport, and to ensure control of the fire contaminants throughout the ventilation system. The airflow required to prevent layering against the ventilation direction, calculated from the Bakke and Leach relations (Bakke and Leach, 1962), is compared with the CFD simulation results. An evaluation of the pressures, generated as a vehicle enters a tunnel portal, using CFD simulation, is also presented for unflared and flared portal configurations. These simulation results are compared with predictions derived using an analytical method which assumes one-dimensional and incompressible flow. Results of the CFD simulation are presented in an animated video format. SIMULATION OF BACKLAYERING In designing a ventilation system for a transit tunnel, the ability of the ventilating air to control and prevent backlayering of smoke and hot gases resulting from a vehicle fire is of prime concern. The buoyant nature of hot smoke causes it to rise relative to the colder, fresh air provided by the ventilation system. If the vehicle fire occurs in a descentionally ventilated tunnel, the smoke may tend to move upgrade in a layer above the incoming ventilation airflow. The layer may become thick enough to engulf a substatntial part of the tunnel cross-section upgrade of the incident that comprises the evacuation route. This effect is termed "backlayering&apos; and it is similar to the development of methane layers in mines for which most studies related to backlayering have been done. Prediction Techniques Analytical A number of studies have been conducted (Bakke and Leach, 1962) to define the characteristics of this phenomena and as a result have produced relations which are used both in the mine and transit ventilation fields to define the air velocities required to control layering. In the transit industry the air velocity required to prevent the backlayering phenomena from occuring during a vehicle fire is called the "critical velocity" (Associated Engineers, 1975) and is dependent upon a number of factors: tunnel height, cross-sectional area and grade; ambient air temperature and density; and the heat release rate of the fire. Common practice in transit ventilation design is to provide an airflow which meets or exceeds the critical velocity. In order to determine whether or not the critical velocity can be achieved with a particular ventilation system, a one-dimensional simulation of the tunnel network is typically performed using programs such as the Subway Environment Simulation program (SES) originally developed in the late 1970&apos;s (Associated Engineers, 1980). The results obtained from SES are compared to the critical velocity to determine the adequacy of the ventilation system. Computational Fluid Dynamics For the backlayering simulations, a commercial CFD code which has been used successfully in a wide variety of engineering applications, was used. It provides numerous options for modeling laminar and turbulent flows, multiple turbulence models, definition of multiple species and chemical reactions between them, a variety of boundary conditions (including constant pressure and constant velocity inlets) and the ability to apply user-defined FORTRAN subroutines. It includes the ability to model conductive, convective, and radiative heat transfer. FLUENT also permits the use of "body-fitted coordinates" to match the computational mesh or grid to complex real-world geometries. Computational Fluid Dynamics Model The model developed to simulate the backlayering phenomena is comprised of an airway of rectangular cross-section, 4 meters wide, 4.5 meters high, and 200 meters long. A laterally

Jan 1, 1995

By W. R. Bush

Radiation protection in uranium mines and nuclear reactors is compared, with the objective of determining if any radiation protection practices which have worked well in one area can be adapted to the other area, especially from reactors to mines since radiation protection is more highly developed in reactors. Several areas are identified where improvements can be made in radiation protection in mines, the most important being improvement in ventilation at the workplace, greater attention to special monitoring during upset conditions, and a need for a substantial increase in radiation protection staff. It is concluded that, although considerable room exists for improvement, the general approach to radiation protection presently being followed seems appropriate for the circumstances encountered in mining.

Jan 1, 1981

By Lindsay Norman

To many who for years have scrutinized the US mineral supply picture, recent, often strident debate on present-day security of many critical mineral supplies echoes sentiments repeatedly expressed in the past decade by the minerals industry. At no time since the last world war has such a flurry of public concern been expressed for the economy&apos;s mineral sector. Where once mineral availability problems were relegated to the newspaper&apos;s business section or not reported at all, today comprehensive analyses of our international mineral posture are discussed in detail by some of the nation&apos;s most respected and widely read periodicals. In past years, disinterest was also experienced whenever the mining industry attempted to carry its message to Congress, the public, and the government&apos;s executive branch. Among minerals professionals, the past decade was a time of particular frustration clue to serious erosion ill US ability to competitively produce the vast array of raw materials vital to the economy acid national defense. Fervent calls for immediate attention were simply not answered. These professionals have understood that mining and agriculture are the primary sources of wealth, fulfilling virtually all needs and creating and sustaining jobs. Why then has it been so difficult to raise the consciousness of the American public, and even more surprisingly, of the government and national leadership? The answer to this question is perhaps endemic to how government functions, but pore important, it begs that mining professionals capitalize on the opportunity and the attention now at hand. Carefully conceived and implemented actions by both private and public sectors are needed more than ever before in the past 35 years. To this end, it is vitally important to seek out and resolve the root causes of supply problems and not dwell on superficial solutions. The following discussion attempts to establish a simple framework to view this process. It does not presume to be an exposition of cause and effect, but hopefully identifies some needed steps. Growing Awareness in the 1970s Of all events stimulating current concern, certainly the OPEC oil embargo has left the deepest impression. It was inevitable that after such a shock, man. Americans would begin asking whether the US was as vulnerable to cutoffs of minerals as it was to oil cutoffs. Then, when serious trade security questions surfaced in sonic mineral-rich nations in Africa and the Persian Gulf, the ominous term &apos;&apos;resource war" began to be heard. Countries such as South Africa, Zaire, Zambia, and Zimbabwe have suddenly become key areas for testing our national security resolve. As the US witnesses the influx of Marxist influence in many sub-Saharan exporting nations and the rising threat to free world access to critical materials and energy, the assurance of adequate supplies is becoming a national issue at last. The US is now learning that self-sufficiency for many vitally important mineral commodities has vanished. Of course, it did not vanish overnight; it had been leaking away for years, and the trend was noted by industry and a few in government. Within the minerals community, suspected weaknesses in America&apos;s resource posture were sought and found. As a result, the country&apos;s heavy reliance on foreign sources fur more than a score of minerals, many extremely vital to security, has been forcefully documented and the case for drastically altering the supply unbalance hits been proposed. The renewed concern for national defense is central to almost all proposals for minimizing US foreign mineral dependence. It is not surprising that many of the voices heard today on the dependency issue are active members or alumni of the militate establishment. Unfortunately, their almost total focus on the security aspects of dependency has tended to obscure important underlying issues which are not directly defense-related. Some of the proposals advanced might mitigate the deeps-dency problems, but they still fall short of curing the underlying problems that have led to a steady loss in mineral self-sufficiency. In almost all instances these problems call be traced to increasing government influence on the free market minerals economy. Some national security proponents seek to attain total self-sufficiency in minerals. Such arguments must he tempered by existing realities. It is easy to demonstrate that the US obtains substantial quantities of sonic essential minerals from potentially insecure sources abroad. That the US will continue to do so in the foreseeable future is not in doubt Uncertainty begins, however, when we try to interpret the significance of these facts. It is important to understand that mineral dependency does not irrevocably lead to vulnerability. Unlike oil, no mineral commodity combines the same degree of universal indispensibility and centralized foreign control of supplies. Moreover, although many US-required minerals are produced by fewer countries than export oil, those minerals cannot approach petroleum in economic or industrial importance. Finally, most foreign supplies come front friendly, secure nations such as Canada, &apos;Mexico, and Brazil. This, aid more, constitutes a vital element in US economic health as a world trading nation. The Cost of Interruption The US is currently stronger and more resilient than many expected after absorbing the oil embargo shock and subsequent price increases. Nevertheless, major worldwide

Jan 6, 1981

By Nenad Spoljaric

Greensand, greensand marl, and green earth are names given to sediments rich in the bluish green to greenish black mineral known as glauconite. The word glauconite is derived from the Greek word glaukos, meaning bluish green. The term "greensand" as a rock name for a glauconite-bearing sediment is more appropriate than "greensand marl," a term that has been doggedly perpetuated in the literature. Because of its potash and phosphate content, greensand was mined and marketed as a natural fertilizer and soil conditioner for more than 100 years. The advent of manufactured fertilizers with adjustable nutrient ratios led to a decline in the use of greensand in agriculture. The material has since been recognized as useful in water treatment. Unfortunately, despite large reserves and world- wide distribution, glauconite has not been utilized to any significant commercial extent because no major application has been found for a substance with its chemical composition and properties. This is probably due mostly to a paucity of research on its potential commercial uses. Extraction of potash received considerable attention during and just after World War I. Because of relatively high extraction costs and a generally low potash content (viz., less than 8%), glauconite lost its appeal as a source of this commodity. Historical Background Greensand was used as a fertilizer in New Jersey in the latter part of the 1700s. During the early 1800s its use became more common; applications of as much as 22.5 kg/m2 were sometimes made, although recommendations for agricultural use suggested 4.5 to 11 kg/m2 (Tedrow, 1957). Many crops, especially the forage type, were said to improve with greensand application; however, because of its slow release of potash, large quantities were required. Certain greensands that contain sulfur and sulfide minerals are harmful to plant growth, and these were classified as poison, burning, or black marls. The availability of higher grade potash salts from other mineral sources and the manufacture of prepared fertilizers displaced the agricultural use of greensand during the latter 1800s. During the mid-1800s the greensand industry, centered in a small section of the eastern United States, grossed more than $500,000/y. Toward the end of the century, however, annual production had dwindled to less than $100,000 in value. By 19 10 there were only six or eight greensand producers grossing less than $5,000/y each (Tyler, 1934). There was a brief revival of the US industry during World War I because of the curtailment of foreign potash, especially from Germany. During the latter 1940s and early 1950s greensand was again recommended as a food nutrient for plants and farm crops. Agronomic studies discussed its potential as a soil additive that gradually releases potash and many trace element nutrients essential for plant growth (Tedrow, 1957). Greensand was sold with the idea that it would condition soil and absorb and hold water while its base exchange properties would release trace elements. For a short time glauconite was used in certain parts of New Jersey as a binding additive in the brick industry, and in the 1800s it was used for making green glass (Cook, 1868). In the early 1900s the base exchange properties of glauconite were recognized for water treatment and the mineral gained acceptance as a water softener. Mansfield (1922) does not mention base exchange even though this phenomenon was known in 1916 or earlier. From 1916 through 1922 several patents for the use of glauconite as a water softening agent were granted. A method was also patented for treating greensand to improve it for water softening and ready regeneration with common sodium chloride brine (Borrowman, 1920, Spencer, 1924, Kriegsheim and Vaughan, 1930). Treated glauconite, on contact with water containing magnesia or lime, takes up magnesium or calcium ions and releases sodium ions. This exchange is limited to the outer surface of glauconite grains, and when all the surfaces have absorbed their capacity, the grains must be regenerated. Regeneration, simply stated, consists of treating or backwashing the glauconite with a sodium chloride solution, which replaces the hard water elements with sodium, thus reviving the glauconite. The process has become more sophisticated due to competition among companies in the water softening business. Greensand products for water softening generally consisted of several different grades distinguished by the particular treatment the glauconite was given during processing. The standard greensand water softener was produced from natural glauconite that was only washed and classified. Its characteristics for water softening are given in [Table 1].

Jan 1, 1994

By K. C. Liddell

Chemical processing research made notable advances during 1986. This overview is necessarily brief. It is intended, though, to give the flavor of selected areas where recent activity has been high. At the 1986 Annual Meeting of The Metallurgical Society, a symposium was held on hydrometallurgical reactor design and kinetics. R. G. Bautista, R. J. Wesely, and G. W. Warren edited the resultant proceedings volume. This is the first available volume on this subject. It includes 26 papers on fundamental kinetic studies, modeling of reaction kinetics and reactor performance, and pilot and production-scale operations. Metals discussed include silver, gold, platinum, titanium, cobalt, nickel, zinc, copper, manganese, and iron. Agitated tanks, heaps, dumps, pachucas, pressure auto-claves, electrolytic reactors, liquid membranes, and fluidized beds are among the reactor types covered. An international symposium dealt with iron control in hydrometallurgy. It was sponsored by the Metallurgical Society of CIM, the Institution of Mining and Metallurgy, The Metallurgical Society of AIME, and Gesellschaft Deutscher Metallhutten and Bergleute. J. E. Dutrizac and A. J. Monhemius edited a proceedings volume containing 41 papers. These covered many areas of process chemistry, solvent extraction, precipitation, treatment of pickle liquors, impurities, residues and the environment, and process selection. Precious metals Concerning precious metals processing, the US Bureau of Mines IC 9059 is noteworthy. It includes papers presented at a USBM briefing at the Western Mining Conference in Denver. Topics covered included ion exchange, staged heap-leaching direct-electrowinning, and mercury precipitation during cyanide leaching of gold ores. Also dealt with were carbonaceous gold ores, carbon adsorption and desorption, heap leaching, the carbon-in-pulp process, and precious metals recovery from electronic scrap and solder. R. C. Sandberg and J. L. Huiatt (Journal of Metals, June 1986, and USBM RI 9022) developed a method to recover silver, gold, and lead from a complex sulfide using ferric chloride, thiourea, and brine-leach solutions. Gallium Gallium recovery was also a subject of considerable interest. Much information on this topic is proprietary. But two papers described solvent extraction of gallium. V. P. Judin and R. G. Bautista (Metallurgical Transactions B, 1986) developed an equilibrium model to separate gallium chloride from aluminum chloride. Tributyl phosphate was the extractant studied. T. Sato and H. Oishi (Hydrometallurgy, 16, 1986) investigated gallium extraction from sodium hydroxide by using Kelex 100. Data were given on the equilibrium distribution and the extraction kinetics. Galena Interest continues in recovering lead by hydrometallurgical processing of galena. J. E. Dutrizac; S. H. Kim, H. Henein, and G. W. Warren; and M. C. Fuerstenau et al. (Metallurgical Transactions B, 1986) all investigated leaching of PbS by ferric chloride. Dutrizac reported parabolic kinetics and reaction control by outward diffusion of lead through a porous layer of elemental sulfur. Kim, Henein, and Warren, however, reported that two leaching reactions occur. A nonoxidative reaction produces H2S and there is an oxidative leaching by ferric ion. Acid dissolution was found to predominate when the acid activity to ferric activity ratio is high. Surface chemical reaction was reported to be controlling. Fuerstenau et al. also reported that mass transfer through the sulfur layer is rate determining. But they believe that the species transferred are chloro complexes of ferric ion. In other work on lead, A. Y. Lee, A. M. Wethington, and E. R. Cole, Jr. of the USBM described an environmentally acceptable hydrometallurgical alternative to the smelting of lead concentrates (RI 9055). Uranium In spite of depressed prices, much work has been reported on uranium processing. R. G. L. McCready, D. Wadden, and A. March-bank (Hydrometallurgy 17, 1986) described the nutrient needs for in-place leaching by T. ferrooxidans. They reported the optimal conditions for uranium solubilization. L. E. Eary, H. L. Barnes, and L. M. Cathles (Metallurgical Transactions B, 1986) carried out an experimental and modeling study of uraninite dissolution. They concluded that ferric ion preferentially leaches uraninite in pyritic ores. Hydrogen peroxide was found to be less selective. A. Vuorinen, P. Hiltunen, and O. H. Tuovinen (Hydrometallurgy 15, 1986) studied redox and precipitation reactions of iron and uranium in leach liquors. P. T. Chiang (Hydrometallurgy 17, 1986) reported on the effect of uranium loading in the DEPA-TOPO process to separate uranium and iron from wet-process phosphoric acid. F. J. Hurst (Hydrometallurgy 16, 1986) conducted a fundamental study of the separation of uranium from phosphoric acid by DEPA and TOPO. D. E. Chia and W. C. Cooper (Hydrometallurgy 16, 1986) reported on bench and pilot scale work to recover uranium by the HIMIX process. They reported that the acid consumption to produce an eluate suitable for yellowcake

Jan 5, 1987

By H. Polat, Q. Hu, M. Polat, S. Chander

The electrostatic charge on spray droplets of ionic surfactant solutions and coal particles was measured and the results were correlated with the dust collection efficiency. When various surfactant were added, the magnitude of the droplet charge increased significantly and it was observed to be a function of surfactant type and concentration. The concentration of maximum droplet charge coincided with surfactant concentration where maximum collection efficiency was observed for these surfactants. Particles of coal also carried substantial amount of charge magnitude of which seemed to be a function of coal rank. Based on the results presented in this paper, it was concluded that ionic surfactant primarily act as a strong electrostatic charge inducer for droplets. Due to interactions between these highly charged droplets and naturally charged particles, the efficiency of droplet-particle collisions play a primary role when compared to the wetting and engulfment phenomenon which could only follow a successful collision. INTRODUCTION Water spray are widely used to suppress airborne dust in mine atmospheres (Walton and Woolcock, 1960; Kobrick, 1970; Hamilton, 1974; Jayaraman et al., 1986). Several investigators have considered the use of surfactants to enhance the effectiveness of water sprays especially for difficult to wet particles such as those of coal (Glanville and Wightman, 1979). The capture of dust particles by water droplets involves droplet-particle collisions, adhesion of particles to droplets, and engulfment of particles into droplets. Surfactants affect these sub processes through their influence on droplet charge, surface tension, and wetting. The last two mechanism have been thoroughly studied in recent years (Walker et al., 1952; Cohen and Rosen, 1981; Glenville and Haley, 1982; Chander et al., 1988; 1991). However, little attention has been paid to the role of electrical charge on particles and droplets on the collision and adhesion of spray droplets and dust particles. Airborne particles of dust have long been known to carry a significant amount of electrostatic charge (Hopper and Laby, 1941; Kunkel, 1948; Kunkel, 1950; Dodd, 1952; Liu et al., 1987; Kutsuwada and Nakamura, 1989). It is reasonable to assume that presence of charge on particles will effect their agglomeration and particle-droplet interactions. Polat et al., (1991) showed that virtually all freshly generated dust particles were agglomerated in air. They suggested that electrostatic charge and humidity were important factors responsible for agglomeration. Previous theoretical studies on the interactions between charged particles and collectors by Nielsen and Hill (1976) show that, the collision efficiency is a strong function of the particle charge. In addition to charge on particles, spray droplets might also carry substantial amount of charge (Chapman, 1937;1938; Blanchard, 1958; Iribarne and Mason, 1967; Jonas and Mason, 1968; Byrne, 1977; Bailey, 1988). In theoretical studies of interactions between a spherical collector and airborne particle, it was found that the collision efficiency was significantly altered depending on whether the collector and the particles were charged. If neither the collector nor the particles carried a charge, the collision occurred by inertial and gravitational forces. The collisions took place on the front part of the collector (the front capture). If either of the collector or the particles were charged, the collision was enhanced due to the induced image forces. If both the collector and the particles were charged, the collision efficiency was significantly affected by the sign of the charge as well as its magnitude. For oppositely charged collector-particle pairs a collision could take place on the rear of the collector even if the particle flied past the collector upon approach (the rear capture) (Nielsen and Hill, 1976; Wang et al., 1986; Chang et al., 1987). On the other hand, the columbic force became negligible as the particle size increased and the inertial force became dominant. The electrostatic attraction was predominant for particles of less than about 2.5 µm in diameter. For particles larger than about 8 µm the inertia of particles was sufficient to overcome the columbic force and inertial impaction became the dominant collision mechanism (Grover and Beard, 1975; Chang, 1987). Previous studies of dust suppression using charged spray droplets generated by applying high voltage to the spray nozzle showed significant improvements in collection efficiencies (USBM open file report, 1983; McCoy et al., 1985). However, it was considered that highly charged spray droplets obtained by direct charging might have

Jan 1, 1993

By S. E. Phillipson

The Mine Safety and Health Administration?s (MSHA) Roof Control Division (RCD) collects a variety of geological and engineering information pertaining to mining conditions in surface and underground mines throughout the United States. Recently, lineament analyses, trends of geologic structures, and inferred stress directions based on mapping at mines with problematic ground conditions, have been integrated into a GIS. The incorporation of different kinds of information into the same geographic coordinates and map projection, placed on digital geologic maps, allows site specific data to be evaluated in a regional geospatial context, identifying trends in the orientation of horizontal stress or patterns of structural geologic features. As more information is collected, the GIS will evolve as a tool for district- and basin-wide evaluations of controls on ground instability, and may evolve into a predictive tool for some kinds of geologic hazards. In addition to the geologic and geotechnical evaluations, the GIS also serves as a searchable database of previous mine investigations. The database can be searched for a variety of criteria, and the results displayed in real geographic coordinates to find the locations of previously visited mines or to evaluate mine fatality and injury data. This not only allows old reports to be found, but also places the information in a geospatial context with respect to neighboring mines or geographic areas. The GIS also has the capability to serve as a digital mine map repository, where maps can be stored in digital, georeferenced format for display in relation to each other and various themes of interest. This allows evaluation of multiple seam mining interactions and proximity to other mines, and on a national level could serve as an abandoned mine map database.

Jan 1, 2008

By Douglas Beahm

Energy Metals Corp. (EMC) holds numerous mineral properties in the northern portion of the Great Divide Basin. The JAB property is one of several potential properties being planned for development as a satellite facility to the greater Antelope uranium project. A National Instrument 43-101 Technical Report was completed for the JAB property. This report estimated total measured and indicated mineral resources on the property totaling 1.6 kt (3,555,022 lbs) U3O8 contained in 2.2 Mt (2.4 million st) at an average grade of 0.073 percent U3O8 at a 0.25 grade times thickness (GT) cutoff in accordance with CIM Standards on Mineral Resources and Reserves. The JAB property is located in Sections 13, 14, 15, 16, 21, 22 and 23, Township 26 North, Range 94 West, approximately Latitude 42° 14’ North and Longitude 108° 00’ West (Fig. 1). This property consists of unpatented mining lode claims and Wyoming state mineral leases com-prising approximately 850 hm2 (2,100 acres).

Jan 1, 2007

By Tim O’Neil

Question: Looking forward, do we face a future in which energy markets, energy policy and energy conflicts threaten to preoccupy, if not dominate, our concerns over economic growth, national security and domestic tranquility? The answer is, we may indeed face such a future. Question: What oil resource is comparable in size to the reserves of Saudi Arabia and presents a tremendous opportunity? The answer, the oil sands in Alberta, Canada. Question: What is the largest mineral staking rush in North American history, still under way? It has so far led to the development of two large mines. The answer is the Point Lake diamond strike in Canada’s Northwest Territories. It led to the development of the Ekati and Diavik mines.

Jan 1, 2004

By Raj K. Rajamani, Samira Rashidi

Wear is an extremely important topic when considering high-pressure grinding rolls (HPGR) for any new application. Given the inevitable variations in ore properties throughout a mine’s life, it is difficult to predict the effect of material and operating conditions on the wear parts: specifically, the HPGR rolls. However, the possibility of continuous scanning of rolls provides ample information to review the wear pattern and ways to optimize it. In this regard, as part of a broader investigation, the feasibility of in-line scanning of HPGR rolls in a laboratory-scale HPGR is studied and presented. The choice of scanners and methods adopted to achieve high-level accuracy for determining wear is discussed in this paper, and the inherent variability affecting the measurements is evaluated. 

By Amy McBrayer, Vladislav Kecojevic, Juan David Valencia Quiceno, Dragan Bogunovic

The mining industry’s commitment to innovation reflects a history of adopting technological advancements to enhance workplace safety, environmental sustainability and vocational training. The objective of this research was to develop an augmented- reality (AR) system for heavy-equipment operators (HEOs) in surface mining. The developed system has the potential to enhance mine safety, training and data-driven decision- making, which presents a significant step toward a more sustainable, effective and technologically driven mining training, contributing to the industry’s evolution and growth. The AR training system leverages Microsoft’s Power Platform and HoloLens 2 capacities to provide operators with detailed and immersive training guides for three mining equipment, including bulldozers, motor graders and haul trucks. AR guides combine speech controls, 3D objects, informative images and explicative videos in the real working conditions to enhance the operator’s learning process. The system has the potential to modify the training structure based on user performance and provides an efficient approach to data collection during training. This project was developed and applied through a case study in a surface mine in the Southern United States.

Feb 1, 2025

By William R. Yernberg

The 2003 Rapid Excavation and Tunneling Conference (RETC) was held at the New Orleans Marriott, New Orleans, LA, June 15-18. The New Orleans conference was the 16th since the RETC was formed in 1971. This year’s conference was sponsored by the Society for Mining, Metallurgy, and Exploration, Inc.(SME), with co-sponsorship of the Construction Institute of ASCE. Attendance at the meeting was 1,178, a conference record. This was up significantly from the771 attendees at the 2001 meeting in San Diego, CA. The RETC was formed to “advance the engineering and scientific knowledge of rapid underground excavation and tunneling through interdisciplinary meetings, publications, technical-educational exhibitions and encouragement of research.” The RETC conferences are now held every other year. They provide an opportunity for individuals to meet with designers, contractors and manufacturers associated with the tunneling industry to share experiences in all phases of tunnel design and construction.

Jan 1, 2003