Search Documents

By H. EI-shall

The conventional beneficiation scheme for Florida phosphates involves reverse flotation with an intermediatory acid scrubbing step. A single reagent flotation process, using fatty acids or amine as the collector, would eliminate the scrubbing step along with the other flotation step. This can not only simplify the process flowsheet, but also result in reduced reagent costs. The potential of single reagent flotation of Florida phosphates using fatty acids as the collector was examined in this study.

Jan 1, 1993

By P. E. Wingrove

The Kayford, Boone and Nicholas Division of Bethlehem Mines Corporation operates a modern coal preparation plant in Van, West Virginia. Since the start-up of the Van Plant in 1976 until the summer of 1980, the refuse handling system proved to be a costly maintenance problem and a material handling bottleneck. During the 1980 two-week miner's vacation the original system, which included two screw conveyors and a drag conveyor, was replaced by an installation utilizing two Flexowall steep angle belt conveyors. This paper describes the technical and economic analysis that led to the new installation and reviews its first year operating performance. The Van facility is a heavy media plant designed to handle 127 mm x 0 raw metallurgical quality coal from the Powellton seam at a maximum feed rate of 590 TPH (metric tons per hour). Depending on mining conditions, the clean coal recovery rate averages between 50 and 65%. The plant is set up with three types of cleaning circuits. Coarse material (127 mm x 12 mm) is cleaned in heavy media baths. Intermediate size material (12 mm x .5 mm) is cleaned in heavy media cyclones. Fine coal (.5 mm x 0) is cleaned in a hydrocyclone1 froth flotation circuit.

Jan 1, 1981

By H. D. Lelono, M. Walden, G. Johnson

3D modelling can be used throughout the mine lifecycle and has proven to be a powerful tool for consultants and mining companies. One of the most significant benefits of 3D models is their ability to enhance collaboration, communication, and understanding between the mine owner, design engineers, and other relevant stakeholders that have a shared interest in responsible mining and site management. Tailings and mine waste management is an interdisciplinary effort that requires effective coordination and communication between a wide range of consultants, operators, and stakeholders alike. The increased emphasis on Environmental, Social, and Corporate Governance (ESG) highlights the importance for mine operators to engage and communicate with all parties involved in the planning, permitting, operation, and closure of mine sites. 3D models are valuable tools that can be used for development of geotechnical conceptual models, allowing for improved design and monitoring of Tailings Storage Facilities (TSFs). A clear conceptual understanding of a TSFs subsurface geology and foundation characterization is essential for proper tailings management, design, and planning. Visualization with 3D modelling can simplify the interpretation of the, oftentimes intricate, mine sight subsurface settings and allows for quick and effective geotechnical conceptualization. 3D models can be used to identify data gaps, optimize field investigations, and streamline the development of numerical stability or groundwater models. They can help communicate the complex nature of subsurface and TSF interactions in a clear, concise, and accurate manner to both technical and nontechnical stakeholders. This paper discusses some of the benefits of 3D modelling in relation to geotechnical analysis for tailings management and provides methodologies for how to improve upon some methodologies that are considered industry standards.

Feb 1, 2023

By David Kress

Grinding mills, both autogenous and ball can be powered by several basic means. The three methods used today are girth gear drives, gearless drives and trunnion coupled reducers. This paper will focus on the first of these methods -girth gear drives. The girth gear drive has been used on thousands of mills which continue to operate successfully. These drives are noted for their simplicity and low cost. In the past, the horsepower capacity of girth gears has been slow to keep up with the horsepower increase required by the mill builders, particularly since the advent of the SAG mill. Gear manufacturers had capacity for 2000 HP mills in the 1950's, 5000 HP in the 1960's and 6500 horsepower in the 1970's. The 70's and 80's brought dual pinion girth gear drives which allowed mill sizes beyond 10,000 horsepower. Gear manufactures who could not keep up with the pace of the horsepower demands and the quality and reliability demanded by the mill builders and users have fallen by the wayside.

Jan 1, 1991

By R. Fernando

"The National Institute for Occupational Safety and Health (NIOSH) National Personal Protective Technology Laboratory (NPPTL) is leading an effort to develop the next generation of self-escape breathing apparatus for egress from confined spaces in emergency scenarios. A backpack style closed-circuit mine escape respirator design was one configuration explored as part of the research imperative directed by the 2006 MINER Act. Stakeholder feedback from MSHA and at the NIOSH Breathing Air Supply Partnership Meeting indicated a smaller belt worn unit that does not sacrifice performance is desirable. This paper outlines some further technology advancements that may be investigated toward developing such a small-sized respirator. Technologies being considered are novel chemicals for improved carbon dioxide (CO2) absorption and oxygen (O2) production, eliminating a dedicated CO2 scrubber by incorporating its function in the spaces of the respirator’s breathing loop and storing O2 in a liquid form with long standby capabilities. When these technologies are applied to a future design, there is the possibility of having an escape respirator that can be belt worn and capable of being certified to 42 Code of Federal Regulations (CFR) Part 84 standards, including sub-part O for escape purposes including mine escape. BACKGROUND NIOSH NPPTL has a Research and Development effort to provide mine workers with state-of-the-art breathing air technologies to comprehensively support initial and continued self-escape, refuge alternatives, and rescue needs, resulting from mine emergencies. As part of this R&D effort, NIOSH invested in the development of a next-generation closed-circuit mine escape respirator (CCMER) which would be compliant with NIOSH’s respirator standard requirements, 42 Code of Federal Regulations Part 84, including sub-part O. The design features of the CCMER also address the MINER Act’s requirements for transitioning between devices without the need for doffing the initially donned device. It would also allow for improved protection when using voice communications with a donned device ."

Jan 1, 2018

By Fredrick Fränding

In mining and quarrying operations, electric motors can fail for a variety of reasons. Some failures are directly linked to demanding production requirements and contaminant-laden environments and, consequently, are difficult to prevent. A sizeable number, however, are caused by ?offline? factors that have nothing to do with production. These include inadequate or substandard motor repair practices and improper motor shipping, storage and installation. The fact that failures are at times attributable to repair- or rebuild-related errors and problems raises the stakes when selecting an electric motor repair provider. Teaming with high-quality electric motor shops can help a company reduce failures due to offline factors, improving motor reliability and cutting downtime costs. Regardless of location or annual revenues, the best motor shops have similar business cultures and share many of the same characteristics.

Jan 1, 2009

By J. G. Groppo

Froth flotation technique is an effective and efficient process for recovering of ultra-fine (minus 74 pm) clean coal. Economical dewatering of an ultra-fine clean coal product to a 20 percent level moisture will be an important step in successful implementation of the advanced cleaning processes. This study is a step in the Department of Energy's program to show that ultra-clean coal could be effectively dewatered to 20 percent or lower moisture using either conventional or advanced dewatering techniques. The main focus of the pilot plant study was on proof-of-concept testing of a dewatering technique for a fine clean coal product. The coal industry is reluctant to use the advanced fine coal recovery technology due to the non-availability of an economical dewatering process.

Jan 1, 1997

By Vincent Tirolo

The proposed Second Avenue Subway is a new two-track subway line running from 125th Street and Park Avenue at the north, east along 125th Street to Second Avenue and south along Second Avenue to the Financial District in lower Manhattan, NY with 16 new stations and 13.6 km (8.5 miles) of track. The project has been broken into four construction phases. The initial Phase 1 operating segment includes three new stations (96th, 86th and 72nd Street stations) with a connection to the existing Broadway line at the 63rd Street Station at Lexington Avenue. Rehabilitation of the 63rd Street Station is also included in the scope of Phase 1. Subsequent phases extend service north and west to 125th Street (Phase 2), south to Houston Street (Phase 3) and finally to Hanover Square (Phase 4). The DMJM Harris/Arup Joint Venture (DHAJV) prepared the Contract Documents MTA for Phase 1. Parsons Brinckerhoff is providing the MTA with construction inspection services for Contract C-26002. In April 2007, NYCT awarded first Phase 1 for $337 million to S3 Tunnel Constructors, a tri-venture comprised of Skanska USA Civil, Schiavone and Shea. Contract C26002 is for the construction of the tunnel boring ma-chine (TBM) launch box and the mining of the TBM tunnels from 92nd Street to 63rd Street. The major part of the contract is to construct a shaft, commonly referred to as the launch box, from East 92nd Street to East 95th Street having dimensions of 244-m- (800-ft-) long by 18.9-m- (62-ft-) wide and a depth of 19.8 m (65 ft), including more than 91,000 m3 (119,000 cu yd) of soil and rock contained within its walls. The launch box will ultimately become the southern half of the 96th Street Station. The focus here is geological conditions at the launch box and existing structures along the launch box. These geologic conditions and existing structures had a major influence on the selection and design of the support of excavation system (SOE), the SOE bracing system, construction staging, the ground movements, dewatering and other challenges of constructing the launch box (Fig. 1).

Jan 1, 2013

By E. R. Bauer

The ground control aspects and occupational safety concerns of extended depth-of-cut mining are presented in this U.S. Bureau of Mines (USBM) report. The scope of extended cut use and typical face operations while extracting extended cuts is reported. A comparative review of roof fall fatalities and a statistical analysis of accidents and injuries for both extended and nonextended cut mining is included. The views and opinions on extended cutting from a series of interviews with mine workers in five states are summarized. In addition, some of the problems and safety concerns of this extraction system are mentioned.

Jan 1, 1995

By Joseph Clare

It’s not the 1960s anymore. Upgrading wastewater pipelines in the current era demands the latest trenchless technology to minimize impacts. King County Wastewater Treatment Division in Seattle, Washington is designing a nearly mile long Direct Pipe® influent sewer combined with microtunneling to replace a 1960s era trunk sewer constructed along and within Coal Creek and its natural area. Trenchless installation using Direct Pipe® and microtunneling was chosen due to reduce impacts to residential neighborhoods, natural creek environments, and the constraints of topography

Jun 13, 2021

By T. W. Camm

The Bureau of Mines conducts studies of the economic impacts of regulations on federal lands. These studies are part of the Bureau Potential Supply Analysis (PSA) program. To meet the needs of these studies, a methodology was developed to estimate operating and capital costs for a mineral deposit given its tonnage, grade, and depth. The format for the cost models in this study was developed at the Bureau's Western Field Operations Center (WFOC), Spokane, W. A., for studies of known and undiscovered resources on Federal lands. These cost models are described in a Bureau publication by Camm (1991).

Jan 1, 1993

By W. J. Mahoney

A good quality assurance program at a coal mine or power plant is accurate, timely, and consistent. The quality analysis is accurate due to a complete sampling of the coal stream loaded into the unit train. The sample analysis is accurate because standardized testing procedures are applied. Once the analysis is completed, the results must be communicated to the electric utility in a timely manner. The electric utility needs the results to better manage the coal inventory at the power plants. A quality assurance program can also help the mine deliver a consistent product to the electric utility's power plants. The importance of the three major tenants for a good quality assurance program: accuracy, timeliness and consistency, are based on major changes that are taking place in the electric utility industry.

Jan 1, 1994

By B. Schimm

Improve the mines productivity by simplifying the mining process, for these tasks the Wirtgen Surface Miner offers an attractive alternative. Surface Miners cut, crush and load material in one operation with only one machine. The cutting depth is controlled exactly.

Jan 1, 1997

By Norman L. Kotraba

In Electric Arc Furnace (EAF) steelmaking, dust emissions are collected in a baghouse to prevent their escape to the Environment. This fine dust, predominantly iron oxide, also contains oxides of various other metals introduced into the EAF from the scrap charge. For example, mixed or galvanized scrap brings with it zinc, lead, and small quantities of cadmium which preferentially accumulate in the collected off-gas dust. Stainless steel scrap brings chromium into the charge, some of which also makes its way into the baghouse dust as hexavalent chromium-containing oxides. Because many of the contained heavy metal oxides are water-leachable, the U. S. Environmental Protection Agency has listed EAF dust as a hazardous waste which, as of August 8, 1988, cannot be 1andfi11ed without first being treated. Moreover, beginning August 8, 1991, all dusts with zinc concentrations of 15% or greater will be required to undergo high temperature thermal treatment to remove the heavy metals prior to any further disposal. This deadline represents several EPA-granted time extensions to the original requirements; extensions which were granted to allow for further development of process technologies.

Jan 1, 1991

By F. Scott Carpenter

During the past several years, more frequent reference to Wollastonite has appeared in print, both in this country and abroad. The reason for this is the apparent growing interest in this mineral as it approaches commercial maturity. Twelve years ago, wollastonite was available in only limited commercial quantity. In 1933, a deposit in California was worked for a short time to provide a calcium silicate raw .material for the manufacture of mineral wool* It was not until the spring of 1953 that Cabot Corporation put into operation a modem commercial plant to produce this material in a variety of grades. These grades covered both a range of particle size and of particle shape. At that time, applications for wollastonite were largely speculative, although a few commercial applications in glass frits and welding fluxes did exist, For all practical purposes, it was a new material for which few commercial uses had been fully proven.

Jan 1, 1964

By T. W. West

During the design and construction of a coal preparation facility, there are many items that can cause serious problems if not properly handled in the early stages of a project. These problems can be a detriment to smooth owner/ contractor relationships, the designing of a flow sheet, the selection of equipment, the design of the facility, the maintenance of schedule and budget, and a smooth start-up. It is the purpose of this presentation to identify some of these problems and to suggest steps that can be taken to reduce or eliminate their impact.

Jan 1, 1977

By G. I. Mathieu

Research and development studies were carried out at the Canada Centre for Mineral and Energy Technology to produce a synthetic forsterite sand from asbestos tailings for Les Sables Olimag Inc. The National Research Council of Canada also supported and collaborated to the project. Theoretically, the technological approach consists of a heat at over 1300°C; however, the process without additive would result in the production of an enstatite-rich product (MgSiO3) having a fusion temperature less than 1600°C. The purpose was to foster the formation of forsterite (Mg2SiO4), a more refractory compound. The fabrication of the forsterite product requires pre-agglomeration of serpentine-MgO with a binder, which is stable at high temperature, to prevent the loss of the powdered magnesium oxide as dust in the kiln off gases and to maintain the mixture homogeneous during the process. Characterization of the end products with respect to mineral composition and thermal resistance are described. The synthetic forsterite in sand form was tested with success under a bath of liquid steel maintained at 1700°C for up to two hours. The advantages of the new sand and its potential applications will be reviewed.

Jan 1, 1992

By Ziyan Ouyang, Haotian Zheng, Spencer Quiel, Mike Mooney, Clay Naito

This paper summarizes the results of an experimental program conducted to characterize the moment-rotation behavior of skewed flat radial joints from large diameter (45 ft) tunnel lining. Both positive and negative joint moment-rotation behaviors were measured experimentally using two-segment joint combination assemblies. The results are compared to closed form methodologies used by designers, e.g., the Janssen method. The differences in observed and model behavior are discussed within the context of design practice.

Jun 23, 2024

By Michael Schultz, Gregory Sanders

The City of New Haven is proposing to construct Downtown Storm Sewer Infrastructure Improvement project to mitigate on-going stormwater flooding in the Long Wharf District. The proposed project includes a 200 cubic feet per second (cfs) stormwater pump station; and a 914 meter (3,000 linear feet) long tunnel segment with an internal diameter of 2.1 meters (84-inches). The tunnel alignment will cross under the Long Warf railyard and then continue parallel to the Vison Trail Route. This paper presents the local geology and subsurface conditions, as well as discusses the major project challenges and risks including construction in soft marine soils and encountering remnants of the former wharf.

Jun 13, 2021

By F. Daviess

A requirement for geological controls during orebody modeling results from the recognition of heterogeneous geological characteristics and/or abrupt variations in orebody geometries. While purely statistical methods are often sufficient for modeling uniform homogeneous deposits, and the only recourse for many that are extremely complex, geological interpretations can be extremely valuable as controls during the modeling process. The advent of relatively inexpensive, sophisticated graphical computer hardware and software has focused considerable attention on the three dimensional visualization capabilities now available to the mining industry. Orebody geometries can be easily imported into many systems as wireframe or solid models, rendered with shading and color, rotated in space, exploded into composite parts, zoomed into and otherwise displayed to awe any audience. The requirements for an initially meaningful, accurate, geological interpretation are sometimes lost when the focus is on an apparently complex, highly resolved end product. Details of the initial data and sensitivities of modeling assumptions are not always sufficiently scrutinized. Software capabilities have extended the geopoetic license into three dimensions. The new tools, while greatly facilitating model construction and rendering, have done little to expedite basic data preparation and analysis. This paper attempts to briefly summarize the purpose and method of the construction of geological controls. The examples selected are from wire­framing and block modeling; application software processes commonly used in the mining industry today.

Jan 1, 1992