Search Documents

This study was conducted to establish the effects of a diesel particulate filter (DPF) system with sintered metal substrate on the concentrations and size distributions of nano and ultrafine aerosols and concentrations of nitric oxides in underground mine air. The study focused on the formation and transformation of nucleation mode particles in mine air under prevailing test conditions. Experimental work was conducted in the NIOSH Diesel Laboratory at the Lake Lynn Laboratory experimental mine, a facility developed to allow evaluation of control technologies directly in underground conditions. The DPF system was examined for four repeatable steady-state engine modes using a naturally aspirated mechanically controlled Isuzu C240 diesel engine fueled with ultralow sulfur fuel. The engine coupled to an eddy-current dynamometer was operated in the underground drift with tightly controlled ventilation. Measurements upwind and downwind of the exhaust system discharge were used to quantify the effects of the DPF system on the mine air. A baseline was established using a standard muffler. The study showed that sintered metal DPF systems reduced the total mass of aerosols in the mine air by more than ten-fold when compared to a muffler. The nucleation mode aerosols (50dem<40 nm) in mine air were found to be strongly influenced by engine operating mode. The concentration of nucleation mode aerosols was found to be significantly higher for high-load modes than for low-load modes. The muffler and DPF system resulted in comparable total nitrogen oxides (NOx) concentrations. However, the nitrogen dioxide (NO2) fraction of the total NOx was found to be substantially higher for both systems for low-load modes than for high-load modes.

Jan 1, 2009

By Stephen Njoloma, William Bracken, Harald Cordes, Ivan Hee

"DC Water’s First Street Tunnel (FST) is part of the $2.6 billion Clean Rivers Project designed to reduce the occurrence of combined sewer overflows into local waterways. Due to flood events in the Bloomingdale and LeDroit Park neighborhoods, the FST Project was accelerated by DC Water to mitigate future flooding by boosting storage capacity and thus relieving the undersized combined sewers.The FST Project was finalized in 2016 as a collaborative effort between DC Water, its consulting team consisting of Greeley & Hansen and McMillen Jacobs Associates, and the design-build team of Skanska, Jay Dee Contractors (SKJD) with WSP Parsons Brinckerhoff as the designer.Scope of project. The FST Project (Fig. 1) included four primary shaft sites, a large 6 m (20 ft) internal diameter, 823- m (2,700-ft) long bored tunnel and three adit connections from the off-line shafts to the large-diameter tunnel. The adits which vary in size and length, are the subject of this article. The Channing Street site (Fig. 2) was established as the main site for an Earth pressure balance tunnel boring machine (TBM) and included a 49-m (160-ft) deep shaft with slurry wall support of excavation and 20-m (65-ft) internal diameter final cast-in-place permanent concrete liner. The construction sites at Adams Street, V Street and Thomas Street each consisted of off-line shaft structures tied to near-surface sewer diversion chambers and ventilation facilities. These three off-line shafts were connected to the large bored TBM tunnel via adit tunnels. Each of the three adits had a portion or the entire length excavated by sequential excavation method (SEM) in frozen ground.The Adams Street adit (Fig. 3) was constructed in two phases. The first phase is the 23-m (75-ft) long and 5-m (16-ft) diameter section immediately outside the drop shaft which also serves as the deaeration chamber and was excavated by SEM. The second phase which is 91 m (300 ft) long and 3 m (10 ft) in diameter was excavated by Micro TBM (MTBM) launched from within the permanently lined deaeration chamber. MTBM excavation commenced toward a reception chamber that was excavated by SEM from the previously bored FST TBM tunnel. This SEM excavation had a 5 m (17 ft) diameter and a length of 4.5 m (15 ft)"

Jan 3, 2018

By Yuemin Zhao, Daniel Tao, Rick Honaker, Maoming Fan

"Froth flotation is the most widely used method of separating fine coal, especially coal with coking properties. However, froth flotation is not efficient for treating ultrafine coal and coarse coal particles. Our previous fundamental test results demonstrated that cavitation-generated nanobubbles around 700 nm in diameter can significantly improve coal and phosphate flotation performance over a wide particle size range. In this study, the effect of nanobubbles on the flotation performance of different particle size fractions of coal was investigated using a bank of 10-L flotation cells, a specially designed 50-mm inside diameter column and a 152-mm inside diameter column. It was found that nanobubbles that were either directly formed on or subsequently attached to the surface of coal particles during the froth flotation process improved flotation efficiency. The use of nanobubbles in a bank of mechanical cells flotation and column flotation significantly increased the flotation recovery at a given product grade. Nanobubbles increased the flotation rate constants of different coal particle sizes. The presence of nanobubbles in flotation slurry could extend the lower and the upper particle size limits for effective coal flotation.IntroductionFor minus 0.6 mm fine coal or minus 0.15 mm ultrafine coal particles, froth flotation is known to be the most efficient and the most cost-effective separation technique. However, flotation efficiency decreases sharply with ultrafine and relatively coarse coal particles. Studies have shown that the low flotation efficiency of ultrafine particles is mainly due to the low probability of bubble-particle collision (Yoon et al., 1989; Ralston and Dukhin, 1999). Enhanced flotation of fine and ultrafine coal can be achieved by increasing collision and attachment probabilities.The top size of particles that can be recovered by flotation depends on the combination of mineral properties and flotation devices. Turbulence in flotation devices is an important factor that affects the stability of bubble-particle aggregates. Even in the flotation of fine particles, bubble-particle detachment can significantly influence the kinetics of flotation taking place in mechanical cells, which provide intensive turbulent agitation (Deglon et al., 1999). Coarse particle flotation is more difficult, because increased agitation is required to maintain particles in suspension and coarse particles are more likely to detach under turbulent conditions (Mankosa and Kohmuench, 2002; Soto and Barbery, 1991). More efficient attachment of particles and improved flotation rate has been observed when tiny bubbles coexist with conventional-sized flotation bubbles (Attalla et al., 2000; Tao et al., 2010; Fan et al., 2010a, b, c, d; Fan et al., 2012)."

Jan 1, 2015

By M. William Lallman

Potash production from natural brines of the Bonneville Salt Flats has a comparatively long history dating back to the start of World War I. However, it vas sot until the late 1930&apos;s that a successful commercial potash operation was achieved by a firm known as Bonneville Ltd. While improvements in operating techniques, pond design and equipment have been incorporated as they became available it should he understood that the basic technology developed in the late 30&apos;s and early 1940&apos;s by Bonneville Ltd, for potash production has not been changed significantly. The purpose of this paper is to present a brief review of the history, geology and hydrology of the Bonneville Potash operations and discuss the cur¬rent methods employed for brine collection, solar evaporation and the recovery of potash and other brine chemicals. A detailed study of the hydrogeology of the Bonneville Salt Flats wan made by L. J. Turk,1 Ph.D. thesis for Stanford University in 1969, under the auspices, of Kaiser Chemicals the Industrial Chemicals Division of Kaiser Aluminum & Chemical Corporation. Turk&apos;s thesis furnished much of the information presented in this paper.

Jan 1, 1976

By A. Bascetin

It was recently proposed to use the pastefill technology as a surface tailings management method. Surface paste is an economic and safe storage method that respects current environmental regulations. There are many problems related to accidents that occur in conventional tailings damps. In this study, the applicability of the surface paste disposal (SPD) method for a Pb-Zn mine in western Turkey was examined. Density was 3.084 and specific surface area was 0.899 m2/g. The mill tailings have very low plasticity and show characteristics of clays and silts in terms of the Unified Soil Classification System. The particle size distribution of the tailings was 39.2% particles finer than 20 µm. The results of this study showed that the physical and chemical properties of mill tailings make them suitable for SPD.

Feb 23, 2014

By W. N. McAnulty

Because so many interrelated technical, economic, legal and political factors are involved in evaluation of commercial mineral deposits, it is common practice today to assign such work to a team of specialists including geologists, mining engineers, metallurgists, lawyers, and economic evaluation experts. Each member of the team plays an important role; the role of the geologist is particularly important. The geologist involved with evaluation of fluorspar deposits needs all the geologic and economic training and experience required for evaluation of metallic mineral deposits. Few, if any, industrial or metallic minerals occur in so many geologic environments as fluorite. Fluorspar, and aggregate of rock and mineral matter containing enough fluorite to make a commercial deposit (ore), is somewhat more limited in its modes of occurrence than fluorite, but it too is found in a variety of environments.

Jan 1, 1970

By C. A. F. Pinto

In the present work compared flotation kinetics of apatite with four different collectors was established. Sodium oleate and rice bra~ oil were used to represent conventional collectors. The new collectors included a sulfosuccinate and a sulfosuccinamate. It was observed that the collection ability of each reagent was very dependent upon the mineral size ranges. The results-were analyzed in terms of size-by-size recovery curves. Flotation rates were also very dependent on size ranges of the mineral particles. One of the new collectors displayed higher flotation rates for coarser particles than the other reagents tested. Synergetic effects were also apparent when a conventional collector was mixed to a new collector.

Jan 1, 1991

By Ryan P. Sullivan, Ben D. DiFiore, Robert J. Auber, Michael A. Piepenburg, Lisa M. Smiley

Pollution to Lake Erie will be significantly reduced by the Westerly Storage Tunnel (WST) system, which is mainly comprised of a 10,000-ft long tunnel and a dewatering pump station in the downstream tunnel shaft. Separate construction contracts for the tunnel and pump station required careful management of the interface risks. A key decision was to decouple the projects by relocating the mining shaft away from the pump station. The need to receive the tunnel boring machine (TBM) in the pump station shaft was eliminated by dismantling the 28-ft diameter TBM in the tunnel then carrying it back through the tunnel and up the mining shaft. This paper discusses how interface risks were successfully managed during design and construction to limit overall schedule impacts.

Dec 1, 2022

By Adolf U. Honkala

Dundee Cement Company was incorporated in 1958. The equity capital for the venture was supplied by a Swiss firm called Holderbank Financier and a group of its principals. Holderbank Financier, a holding company, is a direct outgrowth of Holderbank Cement Company, a company founded in 1912 by the father of Dr Hans Gygi who is the president of Dundee Cement Company and a member of the Board of Holderbank Financier. From one plant in 1912 located in Zurich, Switzerland, Holderbank grew to its present size of 32 plants in 17 countries, having a capacity of 90 million barrels of cement per year. Dundee Cement Company constructed its first cement plant near the little town of Dundee, Michigan. This site was selected because there is an abundance of limestone and clay of the correct chemical composition for cement manufacture and the deposit was advantageously located near the large population centers of Detroit, Toledo, Cleveland, and Chicago. Construction of the 5. 5 million barrel, two kiln, plant was completed and the plant started up in the fall of 1959. After a year or two of the usual problems in a new plant and the expected difficulty of breaking into a nearly saturated market, Dundee began to prosper.

Jan 1, 1970

By G. Frey, D. Scott, C. Pritchard

Controlled recirculation has been used in the metal/nonmetal mining industry for energy savings when heating and cooling air, in undersea mining and for increasing airflow to mining areas. For safe and effective use of controlled district recirculation, adequate airflow to dilute contaminants must exist prior to implementation, ventilation circuit parameters must be accurately quantified, ventilation network modeling must be up to date, emergency planning scenarios must be performed and effective monitoring and control systems must be installed and used. Safety and health issues that must be considered and may be improved through the use of controlled district recirculation include blasting fumes, dust, diesel emissions, radon and contaminants from mine fires. Controlled recirculation methods are expected to become more widely used as mines reach greater working depths, requiring that these health and safety issues be well understood. The U.S. National Institute for Occupational Safety and Health (NIOSH) conducted two controlled recirculation tests over three days at a Wyoming trona mine, utilizing an inline booster fan to improve airflow to a remote and difficult-to-ventilate development section. Test results were used to determine the effect that recirculation had on air qualities and quantities measured in that section and in other adjacent areas. Pre-test conditions, including ventilation quantities and pressures, were modeled using VnetPC. During each test, ventilation quantities and pressures were measured, as well as levels of total dust. Sulfur hexafluoride (SF6) tracer gas was used to simulate a mine contaminant to monitor recirculation wave cycles. Results showed good correlation between the model results and measured values for airflows, pressure differentials, tracer gas arrival times, mine gasses and dust levels.

Jan 1, 2013

By C. Flores

The most common experimental approach of studying one variable at a time while holding all others constant is extremely inefficient. Use of statistical methods enables engineers and scientists to obtain meaningful information with the fewest experiments, reducing cost and wasted effort. In particular, the Taguchi method can be more efficient than traditional full factorial experiment designs, as it can study more variables with fewer nuts, and it is more robust against process "noise." Taguchi designs are also simple to formulate and the results can be analyzed by simple PC spreadsheets. The role and benefits of using the Taguchi method in experiments to develop and optimize processes is discussed.

Jan 1, 1998

By R. M. Yeates

Public concern over possible degradation of groundwater resources has resulted in an array of Federal laws and corresponding state laws to regulate contaminates from solid and hazardous waste. A mine owner must be familiar with environmental regulations which could impact his operation and must know what precautions and corrective actions to take in order to protect his mining operation from potentially expensive remedial actions. The Environmental Protection Agency (EPA), has issued few regulations controlling the management of mining wastes. Federal regulation of mining came primarily under the Surface Mining Control and Reclamation Act (SMCRA) administered by the Office of Surface Mining (OSM). Waste generated from the extraction, benefication and processing of ores and minerals was exempt from regulation under the Resource Conservation and Recovery Act (RCRA), which is EPA&apos;s major instrument in controlling surface contaminates. On December 31, 1985, EPA submitted to Congress a report entitled "Wastes from the Extraction and Benefication of Metallic Ores, Phosphate Rock, Asbestos, Overburden from Uranium Mining and Oil Shale", which will be referred to, henceforth, as the Congressional Report. This Congressional Report assessed the possible adverse effects of mine associated wastes. This report is the first step toward developing regulations with which EPA can regulate waste from the extraction, benefication and process of mineral ores.

Jan 1, 1987

By Elliot Gillerman

The title of this paper implies the presence of silver, nickel, and cobalt minerals at, the Alhambra mine. Perhaps this should be amplified to include uranium, as pitchblende also occurs, possibly in mineable quantifies. A brief history of the Alhambra mine is of interest, both from a historical angle and as pointing up the importance of geology in the-present development. The Alhambra is one of several mines in the Bullards Peak or Black Hawk dis¬trict, ass it is more familiarly known, in southwestern. New Mexico, which was mined for silver in the 1880?s and 18901s, Silver valued between $500,000 and $1,000,000 was extracted from the mine in the 10 years prior to 1893, when operations ceased. Almost all the silver mined was native silver, although a small quantity of argentite was produced. Nickel and cobalt were recognized in the ores, but they were thought to be of no consequence.

Jan 1, 1959

By David Brown, Adrian St. John, John Comins, Mike King

"INTRODUCTION The Crossrail project provides an East-West link across London enabling an additional 200 million journeys each year linking up major business centres and existing transportation interchanges, while reducing congestion at street level and within the current underground system. The project has built major structures in Sprayed Concrete Linings (SCL), including 5 new stations, 6 crossover caverns and numerous passages, adits and ventilation tunnels. Construction has taken approximately 4 years, and has involved the spraying of over 200,000m3 of concrete. At the start of the project there was a lack of available records from previous projects concerning concrete falls, which hindered risk assessments and the ability to make meaningful comparisons around spraying or material performance. This paper redresses this lack of data by providing information on falls experienced on this project and makes recommendations to assist future projects. Construction Methods Table 1 below summarises the main contracts with elements of permanent SCL. The listed primary lining lengths include pilot tunnels, side drift tunnels and enlargements as separate tunnels.A range of construction sequences were used in order to deal with the design requirements, geometry, and the ground and ground water conditions. The following briefly summarises the build up by layers, with typical design dimensions provided for a platform sized tunnel (approximately 9m internal diameter), excluding tolerance allowances. Some linings were sprayed in more than one layer to allow for inclusion of reinforcement layers or to avoid a too aggressive build-up of thickness: •,Initial shotcrete, or sealing, layer (ISL) of 75mm followed by a Primary Lining (PL) of 300mm. •,Regulating layer of 40mm followed by a Waterproof membrane (Sprayed membrane, 3-6mm). •,Secondary lining (SL) of 250mm with a separate sprayed fire protection layer (FPL) of 50mm."

Jan 1, 2016

By Akram Marseet, Andrew J. Petruska, Rik Banerjee

Underground mine roof bolting is a crucial operation for miners’ safety and mine sustainability. Since roof bolting is a manual or human-supervised operation, miners’ safety is at risk due to dust or rock falls. Traditional machine learning algorithms have shown limitations to detecting drillable areas, mainly due to harsh lighting conditions. The authors propose an adaptive deep-learning framework for autonomous roof bolting. The proposed framework is based on implementing a binary semantic segmentation algorithm on color images to classify pixels that belong to rock from those that belong to non-rock. Significantly, the proposed framework implements deep learning semantic segmentation on images from traditional and neuromorphic vision sensors in underground mines. The performance of the proposed model shows an impressive accuracy level of at least 98% at a low number of training epochs with smooth learning curves. The high accuracy enables the implementation of autonomous roof bolting, greatly improving miners’ safety and operational efficiency while reducing human exposure to safety hazards. This research will advance the use of deep learning in mining automation and has the potential to revolutionize the traditional mining industry.

Feb 1, 2024

By M. L. Harris, I. Zlochower, M. J. Sapko, I. E. Perera

Experiments conducted with limestone dusts and dolomitic marble dusts have indicated that when rock dust is wetted and subsequently dried, it becomes a solid, non-dispersible cake. However, in order to be effective, rock dust must be able to disperse as individual particles to inert. To counteract this, rock dust manufacturers created treated rock dusts that will resist caking after moisture exposure. National Institute for Occupational Safety and Health (NIOSH) researchers conducted a series of laboratory-scale experiments on four base rock dusts and their treated counterparts to assess the effectiveness of various anti-caking additives after being exposed to moisture and then dried. The dusts were exposed to moisture using humidity cabinets having a high relative humidity (99% RH) and by also exposing the rock dust bed to water through bottom wicking. The dusts were then evaluated for dispersibility after drying using the NIOSH-designed dust dispersion chamber. The anticaking additives were different concentrations of stearic acid, oleic acid, and xylene-based surfactants. All results were compared to a reference rock dust used to conduct large-scale experiments in the Lake Lynn Laboratory (LLL), Fairchance, PA. When the untreated dusts were dried after exposure to moisture for one day, no dispersion was measured. However, rock dusts treated with anti-caking agents were readily dispersible even after exposure to moisture for six months. This report details the analysis and characterization of anti-caking additives using the NIOSH-designed dispersion chamber and the 20-L explosion test chamber. INTRODUCTION In order for a coal dust explosion to propagate, five elements are required. In addition to the fire triangle in which three elements are necessary to sustain a fire—fuel (coal dust), heat (ignition source), and an oxidizer (oxygen in air)—a combustible dust explosion requires dispersion of a dust cloud (pressure wave) and confinement of a dust cloud (underground mine entry) (1). Coal dust explosions can originate anywhere in a mine. For example, when a small volume of a flammable methane and air mixture is ignited in a closed end, the high-temperature gases rapidly expand to create a pressure wave, sometimes referred to as a “pioneer wave,” that may steepen into a shock wave as it propagates away from the ignition source. The shock wave produces a wind that disperses the dust preferentially from any elevated and exposed surfaces (roof, ribs, belt structure, cribbing, etc.). Factors that are known to affect the intensity of an explosion are the dust particle size, the location of the dust within the entry, the dust dispersibility, and the volatility of the coal dust (1). Particles less than 75 μm (< 200 mesh) in size are most reactive (2). Dusts that are located on the roof, ribs, and elevated surfaces are more readily dispersed than dusts on the floor. Therefore, application of quality rock dust in sufficient quantities is essential to inert coal dust and to prevent continued flame propagation. 30 CFR 75.402 and 75.403 require 80% total incombustible content be maintained within 40 ft of the face, and 30 CFR 75.2 defines rock dust acceptable for use in underground coal mines. It also defined that “when rock dust is wetted and dried, will not form a cake”.

Jan 1, 2019

By Mike Harrington, Tung Vu

The Regional Connector Transit Project is a 1.9-mile-long underground light rail system that will connect LA Metro’s A (Blue), E (Expo), and L (Gold) Lines in downtown Los Angeles. This $1.75-billion design-build project is scheduled for revenue service in Spring 2023. The project consists of 21-foot diameter twin-bored tunnels, a 300-footlong crossover SEM cavern, three new underground stations (at 1st Street/Central Avenue, 2nd Street/ Broadway Avenue, and 2nd/Hope Streets), and cut-and-cover tunnels along South Flower, Alameda, and 1st Streets. This paper, which is the continuation of our previous paper presented in RETC 2019—LA Metro Regional Connector Transit Project: Successful Halfway-Through Completion, will provide insight regarding the construction of major components, and the system integration and testing work undertaken for this complex transit project.

Jun 13, 2023

By P. J. Rua

The Piedras Verdes copper mine is a new run-of-mine (ROM), heap leach, solvent-extraction/electrowinning (SX-EW) operation located 21 km (13 miles) north-northwest of the town of Alamos in the state of Sonora, Mexico. The Piedras Verdes copper mine is wholly owned by Frontera Copper Corp. (FCC), a Canadian corporation, through its 100 percent beneficial interest in Cobre del Mayo S.A. de C.V. (CDM), a Mexican registered company. The January 2008, minable reserves were estimated to be 193.6 Mt (213 million st) at a grade of 0.36 percent copper. The overall recovery of total copper was estimated to be 61.9 percent. The property has an additional 17-year life and is designed to produce 31.7 kt/a (70 million lbs/year) of cathode copper. Construction commenced in early October 2005. The first copper cathode was produced 12 months later at a total capital cost of $100 million. Elevations at the site range from 150 to 300 m (490 to 985 ft) above sea level. The area has excellent infra-structure in the form of towns, power, water, roads, rail, airfield and access to the deepwater port of Guaymas (Fig. 1). The surrounding area is also famous for its numerous polymetallic (lead, zinc, copper, silver and gold) epithermal veins. Some of these were mined for more than 200 years and provided the wealth on which the town of Alamos was built. The original village of Piedras Verdes was located in the area of the proposed openpit mine and, consequently, it was necessary to construct a new townsite 6 km (3.7 miles) to the south before project development could commence. The new town site (Fig. 2), complete with power and water supplies, roads, sewer system, schools, clinic and recreational facilities, was completed and occupied by 49 families in September 2005. CDM received its remaining permits from the Mexican environmental authorities on Sept. 20, 2005. This enabled the company to proceed with full-scale development. CDM owns or controls 27 mining concessions covering the resource. Surface rights to the Piedras Verdes project were controlled by four Ejidos (communal agrarian and/or ranching societies) and five individual landowners. CDM has acquired all surface rights necessary for its mining operations and associated facilities either through outright purchase or long term lease agreements.

Jan 1, 2008

By P. H. S. W. Kulatilake

To exploit an underground mine effectively and safely, it is important to have a good understanding of the geotechnical behavior around underground excavations made in the mine. The aim of this study was to investigate the geotechnical behavior around a tunnel excavated in a metal mine in China at the three-dimensional level. Using the information available on lithology, geological structures, in-situ stress measurements, physical and mechanical properties of intact rock, discontinuities and interfaces between different rocks, a three-dimensional numerical model was built by using the 3DEC software to simulate a tunnel excavation under a high in-situ stress condition. Effect of the discontinuity network, possible intact rock and discontinuity parameter variability, representation of rock masses as discontinuum or continuum material and rock support system on the deformation, stress, failure zone and stability around the tunnel was investigated. A very good agreement was obtained between the collected field deformation monitoring results and the results of the conducted numerical stress analyses.

Jan 1, 2012

By McCarthy. Richard E.

The prime movers of the Centralia Project, the surface coal mine and the power plant, private utilities are very aware of public attitudes. They have established and maintain the reputation for leadership in public service and are genuinely concerned that this project initiate the pro-grams and design the hardware to answer the question :What will be the impact of the mine and the plant on the physical environment, i.e., the air, soil and the water." So in the beginning almost as soon as the decision had been made to go ahead with the project, officials of the two private utilities, Washington Water Power and Pacific Power & Light went on record and publicly stated time and again that the overall approach of the Operators would be to do all that was reasonably possible to safeguard the environment. This attitude became part of the thinking of the project planners, part of the design of the power plant and part of the plan for the surface mine. The coal to be mined is from the Skookumchuck formation. The formation is Late Eocene and is made up of poorly consolidated marine and non-marine deposits. The major overburden removal equipment is a bucket-wheel excavator -conveyor system and a 56 yard dragline. Mining of the coal will be done with truck and shovel. The coal is processed, washed and crushed to 1 ¼ " for delivery to the power plant. The muddy water created by the washing process is chemically treated and the solids removed by a thickener-vacuum filter system.

Jan 1, 1971