Search Documents

By Christopher Newman, David Newman

The ability to assess, address, and predict mining-induced stress distribution is paramount in maintaining a safe and efficient underground operation as coal mines continue to develop at deeper depths and in more geologically complex reserves. This is especially true for longwall mining operations given their limited flexibility in panel layout and orientation. This paper focuses on ground behaviors and conditions observed at two deep-cover, steeply dipping longwall mining operations in Utah’s Unita coal basin. This region is susceptible to coal pillar bump/bounce events as a result of high depth of cover, high-extraction mining, and the close proximity of a thick massive stiff sandstone stratum to active mineworks. The successful prediction of mining-induced coal bump events for Mine A and Mine B operating in the Unita basin has prompted mine management to develop a rock mechanics testing database for reserve calculations. The database is applicable to mine planning as well as the development of multiple numerical models to proactively identify and address adverse ground conditions using input parameters calibrated to site-specific behaviors and conditions. For both Mine A and Mine B, the most critical question relates to longwall development and recovery for “extreme” deep-cover longwall panels at overburden depths greater than 600 m. This paper highlights the impact of high-stress concentrations associated with deep-cover longwall mining as well as the methods applied to mitigate stress impacts on miner safety and longwall production.

Jul 1, 2023

By Erwin Riyanto, Roy William, Karl Llewellyn

The Deep Mill Level Zone (DMLZ) mine is currently one of the deepest block cave mines in the world. The rock mass is heavily veined with little to no joints and faults are usually healed cohesive structures leading to difficult cave mining conditions. The caving process is improved if the rock mass contains fractures with sufficient density that it will cave by gravity as undercutting progresses. Hydraulic fracturing (HF) has been used to create fractures around the cave to improve mining. A seismic monitoring system has been used in DMLZ since the start of mining. Therefore, the seismic activities before, during and after HF can be monitored. Shear wave splitting is a process used to study the impacts of HF on the rock mass. This process involves the measurement of travel times from splitting shear waves after seismic events and using this to define the anisotropy within the rock mass and subsequently fracture density. This paper sets out the methodology for carrying out the interpretation of the shear wave splitting process using seismic data from the fracked cave crown and abutments along with an overview of the benefits to cave mining as result.

Apr 26, 2022

By J. Morris, R. Sellaro

Petro-diesel is a common collector for coal flotation, but the partitioning of diesel range organics (DROs) in process streams has not been widely studied. Preliminary research suggested that under normal dosing schemes total residual DRO contents in process waters should be limited to the sub-ppm water-soluble fraction (WSF). Further, polycyclic aromatic hydrocarbons (PAHs) should partition proportionately with DROs. The purpose of this study was to confirm these findings in laboratory flotation tests. Total DRO and specific PAH contents were measured in the waters associated with the concentrate and tailings streams. The results show that concentrate waters consistently had higher amounts of DROs than tailing waters. Moreover, the DRO contents in both streams generally increased with increasing diesel dosage. In line with preliminary research, DROs appeared to be limited to the WSF, and PAHs tended to partition proportionately with DROs. Under typical operating conditions, it appears that residual DROs should not present an environmental concern, but conditions should be avoided that allow significant overdosing of diesel.

Jan 1, 2014

By M. Scaggs, K. Phillips

"Coal Worker’s Pneumoconiosis (CWP) is an occupational lung disease caused by chronic exposure to respirable mine dust. After decades of steady decline, CWP incidence appears to be on the rise since the mid-1990s, particularly in some regions of Appalachia. Alarmingly, many of these cases have rapidly progressed to the most advanced form of CWP, referred to as Progressive Massive Fibrosis (PMF). Most of what is currently understood about respirable mine dust has been gleaned from routine regulatory monitoring, which tracks total mass concentration of respirable dust (mg/m3) and, less frequently, silica mass content. This paper focuses on the use of thermogravimetric analysis (TGA) as a way to provide basic characterization of the whole composition of the dust, allowing it to be classified into three mass fractions – coal, carbonate, and non-carbonate minerals. TGA was conducted on 59 dust samples collected by miners from eight coal mines in central Appalachia, and the results are discussed in terms of differences between mines, regions, and primary occupations. Consistent with prior results on area dust samples from some of the same mines, results of the personal samples generally show that the coal mass fraction of the dust is relatively low. Carbonate and non-carbonate minerals thus tend to make up the bulk of the dust mass, and vary across occupations and specific mines. INTRODUCTION After nearly four decades of decline, the prevalence of Coal Workers’ Pneumoconiosis (CWP, or “black lung”) in the US has been on the rise since the mid-1990s (Laney et al., 2014; Laney et al., 2010; Suarthana et al., 2011; Pollock et al., 2010; Antao et al., 2005; Blackley et al., 2016). Particularly alarming is the number of cases of progressive massive fibrosis (PMF), which is the most advanced form of the disease (Pollock et al., 2010; Antao et al., 2005; Blackley et al., 2016; Laney et al., 2017). A recent study by Laney et al. (2017) observed 192 US coal miners participating in the Coal Workers’ Health Surveillance Program (CWHSP) who had been diagnosed with PMF since 2000. Of the 163 (85%) that had a normal radiograph on file to use as a baseline, 27 (17%) of these individuals had progressed from a normal radiograph to PMF diagnosis in less than 10 years. Moreover, 162 (84%) of the individuals in that study worked in KY, WV or VA, and 169 (88%) had only ever mined underground. Blackley et al. (2016) also reported on a group of 60 PMF cases that were discovered by a single black lung clinic in eastern KY. Since seeking care at such clinics and participation in the CWHSP are voluntary, and could be influenced by a number of factors, these recent reports may well overestimate the degree of resurgence in severe disease (i.e., versus disease that was previously under-reported). Even so, they highlight a critical need to better understand the cause(s) of disease development and progression – such that effective interventions can be devised."

Jan 1, 2018

By K. D. Luxbacher, E. C. Jong

Perfluoromethylcyclohexane (PMCH), a member of the perfluorocarbon tracer group of compounds, has been shown to be a viable supplement to the widely used tracer gas sulfur hexafluoride (SF6). This viability stems from the fact that PMCH can be used concurrently with SF6 while maintaining adequate chromatographic separation and comparable sensitivity during analysis. However, the release of PMCH in an underground mine ventilation system is challenging due to its physical characteristics. While SF6 exists as a gas at room temperature and pressure and can be accurately released by a variety of means, PMCH exists as a volatile liquid at room temperature and pressure, preventing it from being deployed in a similar manner. One method to release PMCH is to use a permeation plug passive release vessel (PPRV), which allows for the controlled release of the gas. This paper presents the results of a study evaluating various preparation techniques, plug thicknesses and plug materials of an aluminumvessel PMCH release source, so that a source appropriate for the mine scale may be developed.

Jan 1, 2015

By VIVEK KUMAR HIMANSHU, Murari Prasad Roy, Kaushik Dey, Rakesh Kumar Singh, Ashish Kumar Vishwakarma

Sublevel stoping is the most popular and practiced mining method in underground hard rock mines. Proper planning and its execution is the key requirement for stope extraction using this method. The stope extraction has been a challenging task since decades. The major reason is the unavailability of free faces as compared to opencast bench blasting. The geological and geotechnical parameters change gradually even within the stope itself. So, the blast design parameters should be planned according to the scenario of the upcoming ring. The blast design parameters like burden, toe spacing, inclination of blastholes, diameter of blastholes, charge density of explosive, etc., play an immense role in the rock damage. For the proper breakage of rock, the movement of burden is the prime objective. To study this, an explicit dynamic based modeler of M/s Ansys was used. The burden values were varied from 20 to 65 times of blasthole diameter to assess the optimum burden value during the study. The models were simulated for the rock having uniaxial compressive strength as 35 MPa and 102 mm blasthole diameter. Three holes were simulated having depth around 14–14.5 m. Different blast design parameters and respective blast-induced ground vibration have also been measured at the experimental site. The core samples of the rock present at the experimental site have been used for the evaluation of geotechnical parameters. These geotechnical parameters were used in the simulation models. The volume of rock excavated along the free face has been calculated in each model by varying the burden. It has been found that the burden value can varies from 35 to 40 times blasthole diameter (3.6–4.1 m) to achieve a greater volume of rock along the free face for 102 mm blasthole diameter and rock of 35 MPa uniaxial compressive strength.

Dec 22, 2023

By Inoka E. Perera, Michael J. Sapko, Marcia L. Harris

Experiments conducted with limestone dusts and dolomitic marble dusts have indicated that when rock dust is wetted and subsequently dried, it becomes a solid, non-dispersible cake. However, in order to be effectively inert a coal dust explosion, rock dust must be able to disperse as individual particles to air. To counteract this, rock dust manufacturers created treated rock dusts that will resist caking after moisture exposure. National Institute for Occupational Safety and Health (NIOSH) researchers conducted a series of laboratory-scale experiments on four base rock dusts and their treated counterparts to assess the effectiveness of various anticaking additives after being exposed tomoisture and then dried. The dusts were exposed tomoisture using humidity cabinets having a high relative humidity (99% RH) and by also exposing the rock dust bed to water through bottom wicking. The dusts were then evaluated for dispersibility after drying using the NIOSH-designed dust dispersion chamber. The anti-caking additives were different concentrations of stearic acid, oleic acid, and xylene-based surfactants. All results were compared to a reference rock dust used to conduct large-scale experiments in the Lake Lynn Experimental Mine (LLEM), Fairchance, PA. When the untreated dusts were dried after exposure to moisture for 1 day, no dispersion was measured. However, rock dusts treated with anti-caking agents were readily dispersible even after exposure to moisture for 6 months. This report details the analysis and characterization of anticaking additives using the NIOSH-designed dispersion chamber and the 20-L explosion test chamber.

Apr 12, 2021

By J. Morris, R. Sellaro

El petrodiesel es un colector común para la flotación de carbón, pero la partición de compuestos orgánicos de diesel (DRO por sus siglas en inglés) en corrientes de proceso no ha sido ampliamente estudiada. Investigaciones preliminares sugieren que bajo esquemas de dosificación normales los contenidos residuales totales de DRO en aguas de procesos deben estar limitados a la fracción soluble en agua (WSF por sus siglas en inglés) sub-ppm. Es más, los hidrocarburos aromáticos poli-cíclicos (PAH por sus siglas en inglés) debería segmentarse de manera proporcional con los compuestos orgánicos de diesel (DRO). El propósito de este estudio fue confirmar estos resultados en pruebas de flotación realizadas en laboratorio. Se midieron los contenidos totales de DRO Y PAH en aguas asociadas con los flujos o corrientes de concentrados y relaves. Los resultados muestran que las aguas con concentrados tenían de manera consistente mayores cantidades de DRO que las aguas de relaves. Es más, los contenidos de DRO en ambos flujos generalmente se incrementaban con el aumento de la dosis de diesel. De acuerdo con la investigación preliminar, los DRO parecían estar limitados a la fracción soluble en agua (WSF) y los PAH tendían a segmentarse proporcionalmente con los DRO. Bajo condiciones de operación típicas, los DRO residuales no deberían representar una preocupación medioambiental, pero deben evitarse situaciones que permitan una sobredosis significativa de diesel.

Jan 1, 2014

By Michael Rehbock-Sander

The Gotthard Base Tunnel (GBT) is 57 km (35 miles) long and consists of two par-allel single-track tubes with an ex-cavation diameter ranging from 8.8 to 9.5 m (28.8 to 31.2 ft). These are interlinked by cross-passages every 312 m (1,000 ft). Two multifunction stations (MFS) are located in the sections Sedrun and Faido, at one-third and two-thirds of the entire tunnel length (Fig. 1). These will be used for the diversion of trains to the other main tube via tunnel crossovers, for the housing of tech-nical infrastructure and equipment and for potential emergency stops. To reduce construction time, the GBT was divided into five sections and was excavated from several sites simultaneously. The tunnel was excavated from the two portals, Erstfeld in the north and Bodio in the south, and also from three intermediate attacks, with their corresponding access tunnels, in Amsteg and Faido and two vertical 800-m (2,624-ft) deep shafts in Sedrun.

Jan 1, 2012

By Jurgen H. Kleinau

This paper details Keeler/ Dorr-Oliver's experience with the application of fluid bed combustion technology to the burning of coal-mining waste. The designs of two stage fluid bed combustors/dryers are demonstrated as useful in the drying of coal, slag and coke, using coal and coal refuse (gob) as fuel. Anthracite mining refuse (culm) is more than abundant in Northeastern Pennsylvania. After demonstration at Shamokin, Pennsylvania, a full commercial-sized fluid bed boiler using culm is used for district heating in Wilkes-Barre, Pennsylvania. Limited research work has shown the utility of using fine coal as filter aid in sludge in¬cineration. With the rising avenues of the suitability of coal as auxiliary fuel in fluid bed sludge incineration, an expansion of these concepts combines the use of coal or coal refuse as filter aid and auxiliary fuel. Lime¬stone addition controls SO2 emission.

Jan 1, 1985

By Jack A. McQuiston, Thomas A. Cross

Corrosion of equipment and machinery in the coal industry is usually the result of three main agents: acids, chlorides, and abrasion. Acids and chlorides are especially troublesome in coal preparation plants where soluble salts and sulfur in the coal produce a highly corrosive wash solution. Abrasion is common in all operations where coal is handled or conveyed. Together, the acid-chloride-abrasion combination results in some of the worst corrosive conditions found in any industry. The variety of equipment and structures in the coal industry calls for different corrosion control techniques. Table 1 lists the areas of concern for a number of items. Just as there is a wide variety of corrosion problems, there is a wide array of coating materials available. Tables 2 and 3 are selection charts to provide guidance in narrowing down the choices. Experience has shown that a limited number of coating systems work best on coal equipment and structures. These systems are described in Table 4. The good-better-best designation in the table refers to coating system longevity. Good indicates the least costly and shortest service life. In nearly all cases the lowest annualized cost can be achieved by using the coating system rated best, due to the avoidance of costly repaints and unnecessary downtime. The most expensive coating system, though, is worthless unless the coating system is properly applied. Field inspection to insure compliance with specifications is an important aspect, and is a service available from many coating suppliers. Even the best coating systems require periodic maintenance to achieve satisfactory results. Spot rusting from mechanical damage should be repaired annually to maximize the coatingsystem's results.

Jan 2, 1980

By Rodney R. Krause

In attempting to tell the general public about the coal industry's land reclamation efforts, we have often said, "We're not doing things by the book, because we're still writing it." Like any good catchphrase, the statement is not only striking but true. It is particularly true in the mountains of Appalachia, where the problems of mining; and of reclamation are made more intense by the nature of the terrain. Mining and reclaiming the land "by the book' --which is to say by the methods of contour mining traditionally used in hill country--hasn't worked too well. So a lot of conscientious coal operators and associations are trying new methods--new ways of mining, new machines for seeding and planting, and new species to seed. Not all their experience can be transplanted to other areas, and of course I don't believe that Appalachia is the only place where new methods are being developed. Nevertheless, there's enough action in Appalachia to make a detailed examination rewarding, so let's focus on the hills to see what's new.

Jan 1, 1970

By B. M. Eiter, J. Hrica, D. R. Willmer

"Mineworkers are routinely tasked with making critically important decisions about whether or not a hazard presents an imminent danger. Researchers from the U.S. National Institute for Occupational Safety and Health collected formative data to investigate mine safety professional perspectives on workplace examinations, which revealed a potential gap in how mineworkers are assessing risk. During interviews, participants revealed not having a systematic methodology for mineworkers to use to determine if a hazard is considered imminent danger. In this paper, we identify and describe three distinct categories of imminent danger complexity and discuss potential steps that could lead to improved identification of imminent danger situations. Finally, we identify potential practices to incorporate into risk management efforts, including feedback, communication and specialized training, to increase awareness of imminent danger situations. IntroductionIn recent years, the metal and nonmetal mining sector, as categorized by the U.S. Mine Safety and Health Administration (MSHA), experienced an increase in the number of fatalities occurring at mine sites. From 2013 to 2015, 69 mineworkers were fatally injured, twice the number of fatalities in each of the previous two years (MSHA, 2015a). As a way to address this increase, MSHA issued its P15- IV-01 program policy letter, suggesting that “miners would benefit from rigorous workplace examinations conducted by experienced and trained examiners” (MSHA, 2015b). The goal of these examinations is to find hazards in the field and mitigate them before they cause injury or death to mineworkers. While it is important to identify all hazards in the workplace, it is critically important to identify those hazards that are considered imminent danger because they require an immediate response to avoid a severe or even fatal injury."

Jan 9, 2018

By Garland R. Dever

Limestone resources for industrial, constructional, and agricultural uses occur on the surface and at minable depths in several areas along the Ohio River and its navigable tributaries in Kentucky. Operable thicknesses of high-calcium and high-carbonate limestones suitable for use in cement and lime production, steel manufacture, environmental-control measures, and other special uses are documented in Ordovician and Mississippian formations by analysis of 0.3-meter (foot-by-foot) samples. Active and potential mine and quarry sites afford access to water transportation and proximity to a number of industrial and metropolitan centers. Geologic factors affecting the distribution of deposits include the Cincinnati arch, regional dip into the Appalachian and Eastern Interior basins, complex faulting in and near the Western Kentucky fluorspar mining district, and late Paleozoic erosional unconformities in northeastern Kentucky.

Jan 1, 1977

By Michael Gobla

"Since 1994 the Bureau of Reclamation (BOR) has used risk analysis to evaluate dams. Risk considers both the likelihood of failure and the expected consequences should failure occur. Risk analysis relies on the detailed formulation and critical analysis of all possible potential failure modes. Potential failure modes are formulated by describing the sequence of events that must occur to result in failure, where failure is defined as the uncontrolled release of the impounded reservoir. Failure occurs in response to loadings such as water seepage through a dam (static forces), shaking from an earthquake (dynamic forces), sudden flood inflows (hydrologic forces), or accidental overfilling (operational errors). Reclamation has, to a limited extent, applied risk analysis to inactive and abandoned mines to evaluate tailings dams, pit lakes and flooded underground mines. Case histories of potential failure mode analysis, as applied to mine impounded water, illustrate what critical technical information is needed to determine if failure is likely, what the consequences of failure are likely to be, and what are the highest risks that should be addressed first.IntroductionImpounded water and high water content wastes at mining and industrial processing sites are potential threats to public safety and the environment. Recent failures such as the TVA Kingston flyash impoundment failure in Tennessee in 2008 (4.1 million m3 or 5.4 million cu yd) release, the Mt. Poly Tailings Dam failure in British Columbia in 2014 (4.4 million m3 or 5.8 million cu yd) release, and the Samarco Fundao Tailings Dam failure in Brazil in 2015 (59 millon m3 or 78 million cu yd) release have renewed attention to this issue. Potential risks from impounded water at mining and industrial sites originate not only from tailing dams, but also from water in process ponds and conveyance pipelines, sediment retention dams, water retention dams, mine pit lakes and flooded underground mine workings.Conventional water retaining dams also have a record of failure. Notable examples of failure include Vajont Dam in Italy in 1963 (2,600 lives lost), Banqiao and Shimantan Dams in China in 1975 (171,000 lives lost), and Machhu-II Dam in India (10,000 lives lost). After the 1976 Teton Dam failure in Idaho, the U.S. Bureau of Reclamation (BOR) established a Dam Safety Program. By 1984, the agency developed and began using risk analysis methods. BOR operates and maintains an inventory of hundreds of aging dams which were designed and constructed over a period of 100 years. Many of these facilities were designed and constructed prior to the development and adaptation of modern soil mechanics in dam engineering. Diligent observational monitoring, detailed site investigations and the application of risk evaluation to the BOR dam inventory has identified many deficiencies resulting in significant demands on available funding for remediation efforts. The application of risk analysis has allowed the agency to rank sites by risk. By giving priority of remedial efforts to high-risk sites, significant improvements to dam safety have been achieved."

Dec 1, 2016

By H. Soto

As a follow-up to a laboratory study, a pilot scale column for the flotation of coarse particles was designed and then tested in two different applications. In the first test, the concentration of a coarse phosphate ore (normally beneficiated by skin flotation in spirals) was carried out in a flotation plant in Florida. In the second pilot test, the column was used as a scavenger cell in the coarse flotation section of a potash beneficiation plant in Saskatchewan, Canada. Particle size of the phosphate feed was of the order of 0.6-1.0 mm and the potash feed 1-3 mm. The column was 1 feet diameter and was fed at rates between 0.5 to 1.4 tph. The effect of operating variables such as air and water flow rates, bubble size, frother concentration, residence time, sparger, etc were evaluated. The most important factors in column performance were found to be bubble size, air flow rate and the thickness of the froth bed. Best results were obtained in the absence of a froth bed, with low air flow rates and with small bubbles. The paper presents comparative performance and discusses details of the column design. Phosphate recoveries in the column were better than 90% whereas the conventional skin flotation circuit normally yields about 60% recovery for a comparable concentrate grade. Potash recovery from the tailings of the conventional flotation circuit was as high as 42% recovery. Particle size distribution of the potash concentrate was coarse enough to meet requirements for potash fertilizer.

Jan 1, 1993

By Theodore H. Budd, Austin M. Cooney

The paper discusses the background and theories of the conditions that led to the settlement of a Lovat TBM mining in an earth pressure balance mode on a recent project in Milwaukee, Wisconsin. The settlement occurred independent of human error and caused the cost of the project to increase 50 percent. The project was mined in the highly congested downtown area in alluvial and estuarine deposits, 7.6 m below the water table with a prescribed contract requirement that precluded dewatering in deference to concern for foundations of adjacent existing buildings.

Jan 1, 1989

By Donald M. Duncan

An acceptable source of concrete aggregate is available in Kansas City in a continuous, medium bedded, slightly dipping limestone unit. Removal is accomplished in shallow depth, 12 feet to 17 feet high, room and pillar mines. The accepted empirical design spaces 20 foot pillars 60 feet on center. A portion of the 20 foot unit is left in place for roof support. Rock and soil cover is variable to 100± feet maximum. Long-term stability of these mines is affected by numerous factors, including the above mine-rock profile, ground water conditions and mining practice. Crusher-run aggregate sells at the mine for $2.20 per ton, yielding a gross income of $2.00 to $2.80 per square foot of mine. Use of mine space for real estate development requires a new perspective in mine development. Mining practices to obtain long term stabile structures can become an over-riding factor as compared with minimum production costs and maximum extraction ratios. Poorly mined areas are unusuable for secondary purposes. Development cost for lease space in less desirable mines is substantially greater than those planned for a secondary use. Real estate development in mine space involves unique engineering problems. Properly engineered developments offer singular advantages. Warehouse lease space sells for $.50 to $1.00 per square foot per year; fully developed office areas may double these values.

Jan 1, 1968

By Eugene A. Lang

Mr. Chairman, ladies and gentlemen. As a member of the uranium and coal producing community, I am pleased to participate in a session dedicated to a look at these and other mineral markets.(title slide) before sharing some of my thoughts with you, let me tell you a little bit about rocky mountain energy company. It was established as a subsidiary of union pacific corporation in 1971 with responsibility for coal, uranium, and industrial minerals. We participate in four coal mining operations and a uranium mine and mill all in Wyoming, and an aggregate and an abrasive operation in Utah.

Jan 1, 1984

By Ingo Ossenbühl, Wolfgang Dolsak, Vojtech Gall, Axel G. Nitschke

"Yielding support systems for application in underground construction have a long history, primarily in mining. Typical examples are tunnels subject to loading conditions that lead to overstressing of the newly installed support or existing tunnel structures in active fault zones. Recent applications for tunnel rehabilitation projects unveiled the capabilities and flexibility of combined yielding support systems presented in this paper. Frequently, the main requirements for tunnel rehabilitation applications are a fast, safe, and simple installation along with the need for flexibility with regards to existing tunnel geometries. A combined support system consisting of steel sets with yielding connections and special groutable hoses has proven to be an efficient support measure providing a multitude of advantages compared to conventional rehabilitation approaches. The presented yielding support system provides an immediate and active support, while it allows for controlled yielding upon experiencing loads beyond its support capacity. INTRODUCTION The excavation of underground spaces leads to redistribution in the existing stress regime. This load redistribution goes along with deformations in the surrounding rock mass. Magnitude and duration of these deformations depend on the tunnel’s depth and geological conditions, but also on the installed support system. Modern civil tunneling infrastructure has generally an envisioned service life of about 120 years. Conventional tunneling provides typically a dual support system, split into the initial (or primary) and final (or secondary) lining. A typical design principle in civil tunneling is to let the vast majority of deformations acting on the initial lining cease, before the final lining is installed. Based on this approach, the loading on the final lining is significantly reduced and signs of overstressing, such as cracking of the lining, are typically limited to the initial lining. However, special cases in swelling and squeezing ground require different approaches, including yielding support systems."

Jan 1, 2016