Search Documents

By T. G. Melkus

A Setaram C-80 heat flux micro- calorimeter was used to study the surface and interfacial properties of fine coal particles in water containing flotation agents via heat of immersion measurements. Heat of immersion (?Himm) is usually a small exothermic quantity and can be used' to characterize a solid in terms of its relative hydrophobicity or hydrophilicity. The effects of coal type, surface oxidation, mineral matter content, kerosene concentration, and pH on the wetting characteristics were investigated. Results obtained from the calorimetry experiments correlated well with results from independent flotation experiments.

Jan 1, 1987

By M. Adnan Goksel

The hydrothermal agglomerating process described (U.S. Pat. 3,235,371, (1966)) is different from the conventional high temperature processes. Green pellets or briquettes made with mixtures of moist iron ore concentrates and burned or hydrated lime fines are hardened in an autoclave at 198°C and under steam pressure for 1/2 to 5 hours, with or without previous drying. Under the neutral conditions, oxidation of magnetite does not occur as in the conventional processes. The resulting agglomerates are hard and resistant to abrasion and weathering, and they do not disintegrate in the Linder test. The equipment required for the process is not complicated, and favorable operating costs are projected because of the low temperature and efficient heat recuperation. A low capital investment makes the process attractive even when the annual pellet production is below a million tons.

Jan 1, 1968

By W. K. Wedge

The chemical composition of the Pennsylvanian Bethany Falls Limestone Member of the Swope Formation was investigated using optical emission spectroscopy and both flame and flameless atomic absorption spectroscopy. Elements determined were Ca, Mg, Fe, Mn, AI, Si, Na, K, P, Ti, Zn, Cd, Ni, Co, Cu, Pb, Cr, V, and Mo. Over 100 samples were collected from active quarries along a 320-km-long (200-mile) outcrop in northwestern Missouri. Intervals were sampled representing uniform lithology to determine vertical and lateral geochemical variation. The Bethany Falls Limestone is the most extensively quarried Pennsylvanian limestone in Missouri. In 1975, 42 active quarries produced almost 5.4 million tons (6 million st) of stone valued at over 15 million dollars.

Jan 1, 1977

By Wei Victor Liu, Na Zhang, Chengkai Fan, Bei Jiang

The truck haulage data from open-pit mine sites are usually massive and multidimensional with multi-peak Gaussian distributions. Artificial neural networks (ANNs) are well-known machine learning algorithms to handle massive and multidimensional data for building models. Moreover, Gaussian mixture modeling (GMM) is a suitable option for processing the data under multi-peak Gaussian distributions and improving model accuracy. For the first time, this study used a back propagation neural network (BPNN), an extreme learning machine (ELM), and a Bayesian regularized neural network (BRNN) coupled with GMM to deal with the complex truck haulage data and build three weighted ensemble models (WE-BPNN, WE-ELM, and WE-BRNN models) to predict truck productivity at mine sites. Decision tree (DT), random forest (RF), gradient boosting machine (GBM), and extreme gradient boosting (XGBoost) were used to build models to be compared with the weighted ensemble models. The results showed that the WE-BRNN had a higher accuracy than the WE-BPNN and WE-ELM models. The proposed weighted ensemble models performed better than the benchmark models in predicting truck productivity, indicating that a weighted ensemble approach based on the GMM analysis significantly improved the model accuracy. Based on the relative importance analysis, haul distance was the most crucial input variable for predicting truck productivity. This study provides a new approach to predicting truck productivity, which will help mining companies make sound budget decisions and improve mine planning.

Mar 2, 2023

By R. H. Grau

NIOSH’s Pittsburgh Research Laboratory is currently involved in research to identify silica dust generation in underground metal/nonmetal mines. The ultimate goal of this research is to develop control technologies to reduce worker exposure to respirable silica dust. Commodities and job classifications with the highest silica dust exposure have been identified through analysis of the Mine Safety and Health Administration (MSHA) compliance dust sampling database. Dust surveys were conducted in an underground limestone and gold mine to investigate silica dust sources, generation levels, and controls being used. A summary of the mining operations, sampling procedures, resulting data, and suggested methods to improve the dust control will be provided.

Jan 1, 2002

By Ernest B. Snyder

The word "line" has been used loosely for many forms of the common steel plant flux. For example, many people use the word "lime" for nigh calcium and dolomitic limestone, for high calcium and dolomitic quicklime (also called caustic lime, calcined lime; burnt lime, pulverized and pebble lime) and ;van for clinkered dolomite. Calcium hydroxide, also called slaked lime and hydrated lime, is called "lime" but is seldom used as a flux except when the quicklime air slakes in open boxes or bins. All of the above forms of "lime" are used in the steel plant. Calcium hydroxide is used for water treatment, acid neutralizing, and as a lubricant for wire drawing. All the other limes are used as fluxes in the sintering plant, blast furnace or steel producing furnaces. In the production of self-flux or super-flux sinter, high calcium and dolomitic limestone fines are used. Where quicklime fines are available, they may be added to the sinter mix also. The blast furnace uses both high calcium and/or dolomitic limestone. A few trials have been made using iron oxide stabilized dolomitic lime in an attempt to reduce coke consumption and to increase the production rate. The trials were very successful but would' not be economical, except in periods of coke shortages, with resulting extremely high coke cost and exceptionally high hot metal demand.

Jan 1, 1979

By A. P. Mehta

The role of microorganisms in the leaching of metal sulfides is well established (Torma, 1977; Murr, 1980). However, this established knowledge applies mostly to chemolithotropic microorganisms such as Thiobacillus ferrooxidans which function optimally in leaching catalysis between 25-35° C, and in a pH range of 2-2.5. Although leaching with thermophilic microorganisms capable of extending the range of catalytic viability beyond 35° C is also documented, there are few if any attempts to optimize or extend sulfide concentrate leaching with thermophilic microorganisms. When mixed metal sulfides or other materials having different rest potentials (referenced to the standard hydrogen electrode, SHE, in the electromotive series) make contact in a conducting, aqueous medium, the contacting members will act as an electrochemical cell, with the member having the higher rest potential assuming the role of an electrical cathode. In leaching reactions involving such galvanic couples, the cathode becomes passivated, while the anodic member reacts vigorously due to the electro- chemical reaction which occurs (Hiskey and Wads- worth, 1975). Serry, eta1 (1978) observed that when chalcopyrite and pyrite were in intimate contact in natural ores, the chalcopyrite reacted vigorously by galvanic conversion as a result of the higher rest potential (~ 0.63 V) as compared to the chalcopyrite (~ 0.53 V). In addition, it was postulated that because of the elemental sulfur which can form on the anodic chalcopyrite in this galvanic conversion process, reactions in acid-bacterial medium would be expected to have accelerated copper extraction because of the conversion of any sulfur product layer on the chalcopyrite anode to sulfuric acid according to the following general reactions: [MS?M2+ + S° + 2e- (1) and 2S° + 302 + 2H20 bacteria?-2H2SO 4 (2)] where M in reaction (1) designates the metal (or metals in the specific case of chalcopyrite) to be released to solution by galvanic conversion.

Jan 1, 1982

By T. Y. Yan

The various ion exchange reactions occurring during the restoration of formations contaminated with ammonia during in situ uranium leaching are reviewed. Data are presented on the restoration of a previously leached laboratory packed column using line saturated brine. Although this restoration fluid selectively and effectively removed the ammonia, 24.5 pore volumes are required to reduce the ammonia concentration from 500 to 3 ppm. The presence of NaCl in the restoration fluid is beneficial in + improving the selectivity of the system for NH removal and reducing ca++ ion consumption.

Jan 1, 1982

By J. D. Patsey

A computer program has been developed for use by the mining engineer for analyzing drum-type hoists prior to the modification of an existing system or the designing of a new one. Its use permits the preliminary evaluation of a system before seeking the technical assistance of mine hoist designers and manufacturers. Compatible with an IBM-PC, the user-friendly program accepts a variety of data and can analyze hoisting systems for any balance state. The extensive program can be used to: (1) calculate skip capacity to yield a desired production rate; (2) solve for required drum face width; (3) select a permissible wire rope from a menu of 50 available rope types: (4) estimate total horsepower of the hoist plant; and (5) estimate power cost. An example of the model's use in evaluating a hoisting system will conclude the paper.

Jan 1, 1986

By Robert D. Saltsman

The inadequacy of our knowledge of the coal combustion process has long been recognized. This was expressed very well by Spicer and Finney (1). "The control of combustion processes in industry and the design of the equipment necessary for efficient burning to take place have always been very much branches of an industrial art rather than of an exact science. This has been especially true of the utilization of coal, a substance so hetrogeneous and complex in character that all too little is known about its chemical and physical composition.' During the past several years one branch of coal utilization, that of high temperature carbonization; has made significant advances from being an art into being an exact science. This has been accomplished by the development of petrographic techniques for identifying, measuring, and determining the thermal properties of the organic materials which affect the carbonization of coal and the correlation of this information with a pre-existing standard of coke quality, the stability index.

Jan 1, 1964

By P. E. Lenz

In Nevada, large deposits of diatomite were formed during the Miocene / Pliocene in deep, alkaline lakes. Associated sediments are predominately fine-grained lacustrine with varying fluvial-clastic layers. Tephra layers are common, and probably served as a source of soluble silica for the extensive diatom colonies. Four companies are currently producing diatomite from Nevada deposits. Nevada ranks second to California in annual domestic production. Nevada diatomite is used in filter aids, fillers, absorbents, catalyst supports, and many other products. Economics and mineral reserves indicate that diatomite production in Nevada will be significant well into the next century.

Jan 1, 1993

By H. T. Mulryan

Talc is used as an essential ingredient in a variety of plastics applications ranging from polyester body patch compounds through polypropylene automotive, appliance and household furniture components to high performance parts made from liquid crystal engineering resins. This paper focuses on polyolefin applications, the three-tier market for talc in polypropylene, the effects of various tales in typical compounds and trends in each market segment. Emphasis is given to emerging markets, examples of which are polypropylene compounds that mimic higher cost resins, and polyethylene films. Customer requirements for tales for these purposes are discussed.

Jan 1, 1994

By F. Habashi

Chile is at present the largest copper and rhenium producer and was before World War I the largest nitrate producer. She is also an important producer of lithium carbonate and molybdenum oxide. An important event in the history of the country is the Pacific War of 1879-1883 in which she acquired the northern provinces initially belonged to Bolivia and Peru. In 1888 Chile annexed Easter Island. The Chilean mineral and cultural history is briefly reviewed together with the people who contributed to her development. The present report is the result of a number of academic and industrial visits to Chile during the period 1992 to 2009.

Jan 1, 2011

By F. Habashi

The peninsula that lies between the Black and Mediterranean seas, called Asia Minor by the Romans and Anatolia by the Greeks, was one of the crossroads of ancient civilizations. The fall of Constantinople in 1453 was a turning point in the history of mankind. Visits to Istanbul, Ankara, Eskisehir, Cappadocia, and Trabzon will be given together with the history of the country. Mineral resources of the country will also be briefly outlined.

Feb 23, 2014

By Robert L. Bates

The field of industrial minerals and rocks includes such a wide diversity of materials and occurrences that communication is essential to foster a sense of "belonging? among geologists and other professionals. Besides, exchange of ideas and information is essential in meeting the needs of an ever-expanding world economy. A survey of the field shows to what an extent such communication--especially in the form of conferences and their proceedings--has increased during the past 25 years.

Jan 1, 1995

By F. Habashi

Japan was a closed society until 1853 when it was forced to open to the West. Mining, metallurgical, and geological education started there around 1861 when a graduate from Yale University in USA went to Japan to organize the first School of Mines. This was followed by other metallurgists from Great Britain, France, and Germany and thousands from other disciplines. The present report is a summary of the writer's first contact with Japanese metallurgists and his visits to a number of universities and research institutions in the past years.

Jan 1, 2012

By K. N. Han, M. C. Fuerstenau

Challenges in five major areas of hydrometallurgy are presented and discussed. These are: leaching low-grade oxide and sulfide ores; oxidative leaching of sulfide concentrates; processing refractory ores; bacterial leaching and processing: and secondary metal recovery.

Jan 1, 1989

By Y. A. Attia

Auriferous sulfide ores often contain very finely disseminated gold and other precious metal particles inside the sulfide crystals. The encapsulation of precious metal particles gives rise to the refractory nature of such ores to current extraction methods. As a result, these fractions are frequently lost in the tailings. The purpose of this work was to investigate the feasibility of pretreating these refractory tailings with bioleaching before employing standard extraction techniques such as cyanidation. Leadville gold ore tailings containing auriferous pyrite were first concentrated by froth flotation. The pyrite concentrate was treated for different periods of time with 12 weeks adapted thiobacillus ferrooxidans before cyanide leaching. The bioleaching of the concentrate before cyanide leaching increased the gold extraction from 32% to 95% and that of silver from 48% to more than 98%.

Jan 1, 1987

By A. D. Walters

Computer simulation models of preparation plant operations and cost analysis have been used to determine the profitability of individual coals. The model's input consists of raw coal size and washability analysis, operating cost data, and raw coal and clean costs. The model's output predicts yields, qualities, costs and profitability for an individual coal.

Jan 1, 1987

By Giovanni Barla

The stress-relief method for the determination of the ground stress tensor is a common procedure in rock mechanics. In particular, the method of applying gauges to the end of a borehole is a well-established technique. Investigations, both experimental and theoretical, indicate that large discrepancies can exist in the determination of the ground stress tensor when the rock substance is not the ideal elastically isotropic material assumed for the reduction of data. The purpose of this paper is to extend the analysis of strain gauges applied to the end of a borehole to rock material more closely approximate to an orthotropic substance.

Jan 1, 1969