Search Documents

By W. J. Cieslewicz

Geologically, northeastern Siberia is a region occupied by a folded belt of Triassic and Jurassic sediments and volcanics. Gold mineralization is of Upper Jurassic age. Most of the stream placers formed during the Quaternary. Placer gold was first discovered in 1916. Between 1930 and 1957, mining was carried out by the "Dal 'stroi," a Russian concentration camp organization. Since 1966, the mines have been worked mechanically. About 10 mining districts are now active, producing, altogether, 110 to 135 t (120 to 150 st) of gold annually.

Jan 1, 1987

By H. V. Alminas

The U.S. Virgin Islands consist of three major islands (St. Thomas, St. John, and St. Croix) and some 50 smaller islands that are located primarily along the coasts of St. Thomas and St. John. St. Croix, the largest of the islands, is located approximately 160 km south-southeast of San Juan, Puerto Rico and is about 218 km in area (Fig. 1). St. Thomas, the second largest island is located 64 km east of Puerto Rico and incorporates approximately 77 km2. St. John is located immediately to the east of St. Thomas and incorporates approximately 49 km2. The climate in the U.S. Virgin Islands is maritime tropical. The average annual rainfall at higher elevations is 127-152 cm and at lower elevations 51-76 cm. There is no well-defined wet or dry season. Temperatures generally average in the 80's (F°) with only a 5°-7° F variation throughout the year.

Jan 1, 1987

By K. M. Mohamed, R. K. Zipf

The shear strength properties of generic cement foam material and cement foam/concrete interfaces were examined at three testing scales. In laboratory direct shear tests on specimens with average shearing area of 0.006 m2 (10 in.2), the cement foam material had average peak and residual shear strengths of 0.88 MPa (128 psi) and 0.39 MPa (56 psi), respectively. Depending on the concrete strength, the cement foam/concrete interfaces had peak and residual shear strengths ranging from 0.71 to 0.81 MPa (103 to 117 psi) and from 0.27 to 0.29 MPa (39 to 42 psi), respectively. In laboratory direct double shear tests on specimens with average shearing area of 0.084 m2 (130 in.2), the cement foam/concrete interfaces had average peak and residual shear strengths of 0.17 to 0.30 MPa (25 to 44 psi) and of 0.11 to 0.23 MPa (16 to 33 psi), respectively. In large shear tests of simulated cement foam seals with the Mine Roof Simulator (MRS) test frame, cement foam/concrete interfaces with shearing area of 1.486 m2 (2,304 in.2) had average shear strengths of about 0.08 and 0.16 MPa (11 and 23 psi) along the roof and floor interfaces, respectively. The average shear strength through the cement foam material was 0.38 MPa (55.3 psi). Finite element analysis of the large seal tests and the back analysis of the shear strength of full-scale cement foam seals conducted at the NIOSH Lake Lynn Laboratory confirmed shear strength of about 0.14 MPa (20 psi) along the seal/rock interfaces. The study concluded that the structural analysis of cement foam seals should be based on their residual shear strength determined from small laboratoryscale tests of the cement foam/concrete or rock interface and not be based on their peak strength.

Jan 1, 2014

By A. Halim, A. Martikainen, S. GYAMFI

This paper outlines a unique case of the development of strategies to reduce ventilation and heating costs in Konsuln iron ore mine in northern Sweden. The mine, located just south of Luossavaara-Kiirunavaara Aktiebolag’s Kiruna iron ore mine, was developed as a test mine from 2018-2020 for the Sustainable Underground Mining (SUM) project. Besides functioning as a test mine, Konsuln also contributes to ore production. The existing mine ventilation system was designed for the current production rate of 0.8 million tons per annum (Mtpa). There is a plan to increase this rate to between 1.8 and 2.0 Mtpa.

Sep 30, 2021

By D. M. Carris

Since the Buffalo Creek incident in February, 1972, Federal and state environmental agencies have had the pressure on the coal industry in the Appalachian area to close the coal processing plant water circuits. In an attempt to comply with this requirement, Eastern .Associated Coal Corp. decided to install a vacuum disc filter system at its Kopperston plant to eliminate the tailings pond and reduce the amount of plant make-up water. It was recognized at the time that the plant static thickener tailings would be a very difficult slurry to dewater because of its unusually high clay content. The following is a case history of the Kopperston installation and the refinements Eastern has made in its vacuum disc filter operation to increase efficiency.

Jan 1, 1979

By M. Allan Holtz

The shipment of coal, ores, and minerals in bulk form during the winter months presents a difficult problem in emptying rail cars. U. S. Steel Research in cooperation with U. S. Steel Coal Operations bas laboratory tested and field monitored the effectiveness of using freeze conditioning agents (FCA) to minimize the frozen coal problem. This report examines, in an overview manner, our experience after four seasons of treatment using different FCA agents on raw and preparation plant products. Our observations indicate that if an FCA is applied correctly it is effective mineral to mineral. Freezing problems still occur at the interface between the coal and the metal of the car sides and bottoms. Leading chemical suppliers have made positive improvements in their FCA formulations with second and third generation products. Further advances are needed to make chemical treatment for the prevention of frozen coal a real full-proof method.

Jan 1, 1980

By Robert S. Lehto

Zinc concentrates received in La Oroya zinc refinery are marmatitic in nature, contain about 11% iron and traces of other metal values, Figure 1 shows the zinc circuit. The calcine from the roasted concentrates is leached in spent zinc electrolyte. Major part of the impurities is iron which has been oxidized to its trivalent form, This is the origin of the zinc leach residue for which the ZILERET process was developed and so named. The impure liquor from the leach is sent for purification and thence to electrolysis- zinc deposits on aluminum cathodes from which: it is stripped, melted and cast into slabs Typical assays of zinc calcine and leach residue are given in Table 1. Metal values contained in the leach residue, without counting any value of iron, amount to roughly $130 per short ton.

Jan 1, 1969

By H. Colin

The basic industry, such as mining, ferrous and non-ferrous, cement and aggregates, stores and handles millions of tons of raw materials, re- quiring often different types of storage, blending and reclaiming systems.

Jan 1, 1980

By Y. C. Kim, F. Szidarovszky

G.M. Philip and D.F. Watson The article cited above reflects the difficulty that is often encountered in interpreting different aspects of kriging. Baafi et al. write : "Due to negative kriging weights, negative block grades may be obtained in some extreme situations, which makes no practical sense." Their solution to this particular problem is to constrain the kriged estimates to data values that have positive weights, i.e., reduce the subset size contributing to the estimation. As Journel (1986, p. 133) has already observed, "Negative weights are no evil." Indeed, they are an ineluctable result of the Lagrangian multipliers in the system of simultaneous equations. The fact that data distant from the estimation point may be given negative weights simply means that the influence of such distant values must be negated because their influence is contradictory to closer values (as illustrated by Baafi et al. in their Figs. 3 and 4). Of course negative kriging weights applied to distant grade values will not in themselves induce negative grade at some central interpolation point. Negative grade values, rather, seem to be a particular artifact of automatic methods of estimation involving accu¬mulations (Philip and Watson, 1985a, 1985b, 1987b). The elimination of negative weights, suggested by Baafi et al., is likely to exacerbate a quite different problem of kriging and piecewise spline interpolation discussed elsewhere (Philip and Watson, 1987a). In interpolating large data sets of scattered observations, changing local subsets or neighborhoods must be selected automatically. Because of the mathematical formulation of kriging and spline interpolation, discontinuities then occur between closely-spaced estimation points as the subset used in the estimation changes. If this subset is reduced in number and size, the discontinuities will be amplified and more common. ? References Journel, A.G., 1986, "Geostatistics: models and tools for Earth Sciences," Journal of Mathematical Geology, Vol. 18, No. 1, pp. 119-139. Philip, G.M., and Watson, D.F., 1985a, "Theoretical aspects of grade-tonnage calculations," International Journal of Mining and Geological Engineering, Vol. 3, pp. 149-154. Philip, G.M., and Watson, D.F., 1985b, "A deterministic approach to computing ore reserves. I, Grade Estimation," Earth Resources Foundation, Occas. Paper 2, The University of Sydney, 24 pp. Philip, G.M., and Watson, D.F., 1987a, "Neighborhood discontinuities in bivariate interpolation of scattered observations," Mathematical Geology, Vol. 18, No. 1, pp. 69-74. Philip, G.M., and Watson, D.F., 1987b, "Estimating interactions of topological functions," Mathematical Geology, Vol. 18, (at press). Reply by Y. C. Kim Before replying to the comments by Philip and Watson, it is desirable to establish the original perspective of our paper, which was intended primarily for the practitioners of mining who possess a working knowledge of ordinary kriging. The paper tried to convey the following practical points: (1) there are circumstances in which one observes negative weights, (2) illustration of circumstances under which one can expect negative weights, (3) should one obtain a negative estimated grade, one can resort to elimination of negative weights using the technique outlined in the paper, and (4) one could normally select only the first layer of surrounding assays to estimate the block grade. Under such a perspective, most of the comments by Philip and Watson are irrelevant and misdirected. For example, the practitioners do not find it difficult to "interpret" the results of ordinary kriging, as evidenced by the fact that they have been using the results for nearly a decade. Nor are the practitioners concerned with discontinuities in estimated block grades due to changing neighborhood of assays during kriging. What matters to the practitioners is the fact that kriging does provide the best estimate among all the estimation tools available to them as of today. ?

Jan 2, 1987

By S. P. Banerjee

Injection of inert gases to combat mine fires has been practiced in various parts of the world for a long time. Of late, nitrogen has become the preferred inert gas for control of mine fires and safe salvage of longwall equipment as compared to carbon dioxide or fuel gases produced from burning of fuel. In India, carbon dioxide has been used for fire fighting in a number of mines during the 1960s and 1970s. More recently inert gas produced from burning of fuel oil in surface plants has been used in controlling the atmosphere in fire areas in two mines. In yet other cases, liquid nitrogen has either been poured directly into fire areas in liquid form or injected in gaseous form to keep the fire in check. Nitrogen produced in liquid form in an oxygen plant is more costly than nitrogen produced from PSA (pressure swing adsorption) based plants. A PSA-based plant has been installed in one of the Indian mines in 1986 and more are in the offing. This paper reviews the application of various inert gases in Indian mines and discusses the likely trend of inert gas application in Indian mines in the future.

Jan 1, 1987

By I. Papadopoulos

Nowadays, geophysical prospecting is implemented in order to resolve a diversity of geological, hydrogeological and geotechnical problems. Though plenty of applications and a lot of research have been conducted in the country-side, only a few have been reported in the literature concerning urban areas, mainly due to high levels of noise present that aggravate most of the geophysical methods (e.g. electromagnetic, seismic, gravity etc.) or due to spatial limitations that hinder normal method implementation (e.g. electrical). Among all geophysical methods, electrical tomography proves to be the most rapid and urban noise insusceptible technique. This work presents a case study in the urban area of Hania (Crete I., Greece), where Electrical Resistivity Tomographies (ERTs) have been carried out for the detection and identification of possible buried ancient ruins or other manmade structures, prior the foundation of a building. Nineteen profiles were surveyed in a 20x40m grid using dipole-dipole configuration. The results indicate two areas of interest, that are interpreted as probable old wells, in the context of the existence, in former times and in the same area, of an olive oil plant. In the vicinity, near surface ancient ruins have been disclosed, but no such evidence provided this survey, for the particular area under study and the prospected depth. The collected ERT-data were processed by applying advanced algorithms in order to obtain a 3D-model of the study area that depicts more clearly and accurately the interesting subsurface structures.

Jan 1, 2005

By V. Perdikatsis

The aim of this paper is the study of the pollution of soils in greenhouses because of the use of pesticides. The degree of pollution was studied in relation with the mineralogical and pedologic properties of the soil. The study was con-ducted in the region of Kountoura, Palaiochora, situated in the south of the prefecture of Hania/Greece. Several samples of soil, originated from 4 greenhouses were analyzed. 5 pesticides with organic drastic compounds were chosen for analytical determination using GC-MS from 18 which were applied in total during the period of sampling. It was concluded that the adsorption of pesticides in the soil of greenhouses is connected with the percentage of the clay fraction and the content of organic carbon.

Jan 1, 2006

By Steve Kral

Competition in the gold mining industry throughout the world has become fierce in recent years. The challenge facing operations personnel is to produce more gold for less money. Likewise, the explorationist's charge is to find more gold in a more cost-efficient manner. That means using new technology to find new gold deposits and expand present ones. More accurate mapping instruments are available to geologists in the search for new deposits. Advanced geophysical and geochemical methods enable explo¬ration teams to review previously mined districts in their search for minable reserves. Four technical sessions on the geology, exploration, and development of gold deposits were part of the program at `world Gold '89,' a Gold Forum on Technology and Practices," held by SME and The Australasian Institute of Mining and Metallurgy in Reno, NV, Nov. 5-8, 1989.

Jan 1, 1990

By Manuel Bernales, Aldo Leon, Alexandra Carlier, Bern Klein, Andre Xavier

Mining companies and governments at both the local and national levels recognize that Participatory Environmental Monitoring and Surveillance Committees (PEMSC) are necessary mechanisms for meaningful engagement at the community level. In many cases, PEMSCs are established as volunteer initiatives by mining companies or by the mining communities themselves. In Peru however, they can also be recommended by the government as way to address social conflict. Most PEMSCs are launched while a mine is in operation and have the objective of monitoring both water quality and quantity. Many established committees are currently evolving and adopting a more comprehensive approach, as well as expanding their initial scope from a river or micro-basin focus and watchdog agenda, to a broader regional integrated resources management view. This paper examines the origins of Participatory Environmental Monitoring and Surveillance Committees in Peru. It also discusses the typology of these committees, and the scope of their work. Furthermore, it looks at the challenges faced by these committees, as well as existing opportunities for mining companies, governments, and civil society. Finally, this study presents a governance model that could contribute to the long-term existence of these committees. This discussion is further informed by the results of a national workshop that took place in October 2016 in Peru, in which over 200 representatives from 22 monitoring committees, government and mining companies participated.

Jan 1, 2017

By George H. K. Schenck

It seems appropriate to review the history of mechanization of our underground coal mines at this time when many favorable flags are flying for this industry. It is a reasonable hope that such a review may stimulate thinking as to the directions that new technological developments are apt to take and in which members of the Society of Mining Engineers are destined to play important roles. Discussion of the relative importance of the various changes that have taken place since the advent of electric power provides the starting point. It is in the economic factors utilized that we find conditions which permit more efficient utilization of the capital committed to the industry. Concepts rather than specific items are emphasized in the following discussion because once the value of a concept, such as mechanical conveyors, is established, it then spawns many variations which are not significantly different. The shift from animate to inanimate energy has been the most important change in the modern industrial scene, including coal mining. Although introduced into coal mines for some purposes early in the period of general electrification, the coal industry adopted mechanical power relatively slowly, and 1944 was the first year in which a majority of deep-mined coal was mechanically loaded.

Jan 1, 1968

By Estban M. Domic

The modem copper industry presents an excellent opportunity for the application of clean, environmentally friendly techniques using currently available hydrometallurgical technologies. This paper briefly reviews key events in the development of modern hydrometallurgy in Chile. Discussion is given to those prominent events whose impact continues to be felt on most projects currently underway. Mention is also made of the foundations of heap leaching technologies, preceded by agglomeration and acid curing, known as the T.L. Leaching Process, the cornerstone of more recent developments. A review is also presented of the leading copper hydrometallurgy projects of the 1990s. A list of those projects, their tonnages and the estimated date of implementation is provided. The conclusion provides an overview of developments in research and the trends in the implementation of copper hydrometallurgy projects in Chile for the coming years.

Jan 1, 1998

By James A. Pendleton

The Legislature of the State of Colorado adopted House Bill 1223, "The Colorado Surface Coal Mining Reclamation Act" (The State Act), in 1979. This Act provided for the creation of a state regulatory program as accommodated within Public Law 95-87, "The Surface Mining Control and Reclamation Act of 1977" (SMCRA). Section 34-33-121(2)(a) of the Colorado Revised Statutes (CRS) and Section 516(b) of Public Law 95-87, identically require the underground coal mine operator to "Adopt measures consistent with known technology in order to prevent subsidence causing material damage to the extent technologically and economically feasible, maximize mined stability, and maintain the value and reasonably foreseeable use of such surface lands, except in those instances where the mining technology used requires planned subsidence in a predictable and controlled manner..." On July 23, 1980, the Colorado Mined Land Reclamation Board adopted regulations to administer and enforce the State Act. Amendments to the Rules, including the subsidence regulations were adopted by the Board in August of 1981. These regulations require the prediction, monitoring and mitigation of "material damage" caused by subsidence.

Jan 1, 1985

By W. A. Steingraber

This paper discusses the application of deep well disposal techniques to the problem of disposing of large volumes of low level radioactive wastewaters generated by the in situ uranium mining industry in Seth Texas. Data is presented on wastewater composition and volumes, geologic and hydrologic parameters of the disposal reservoirs, tell construction techniques, well operation, well monitoring requirements, and critical factors in evaluating the Safety and environmental impact of a deep injection well system.

Jan 1, 1980

By Dennis Asmussen

The peatlands of the U.S. and Canadian parts of the Upper Great Lakes region have a long history of modest utilization in agriculture, forestry, horticulture, and as natural undisturbed areas. Only recently have they been assessed as potential sources of non-renewable or renewable energy. This new interest in peatlands, should current proposals be realized, might mean the commitment of millions of acres to energy production purposes. The magnitude alone of this potential utilization of peatland signals the possibility of substantial environmental disturbance, local resource shortages, resource use conflicts, and social and economic change. Peat- land resource managers in the region are just beginning to weigh the advantages and disadvantages of large-scale peatland utilization. The Minnesota Department of Natural Resources has made a considerable effort to study peat resource management issues and will shortly make recommendations to the state legislature regarding utilization alternatives. What follows is a general discussion of peatland utilization and management trends in the region with a focus on Minnesota and its peatland management efforts.

Jan 1, 1980

By J. Finch, W. Petruk, R. G. Pinard

An investigation was conducted to determine the minimum number of samples that must be studied by image analysis of polished sections to characterize a mill product and determine the apparent mineral liberation. It was found that a representative polished section cannot be prepared from an unscreened sample that has a wide size range of particles. Similarly, individual screened fractions are not representative of the sample because minerals are partitioned during screening, and the quantities of soft brittle minerals are increased in fine grained fractions, whereas the quantities of hard minerals are increased in coarse grained fractions. It is assumed that results obtained by combining data for a series of narrow size range screened fractions (one Tyler size range) are representative of the sample, and relatively accurate apparent mineral liberation data can be obtained for a mill product by analyzing each fraction and combining the data. Somewhat less accurate data would be obtained by analyzing a series of screened fractions that have a wider size range of particles (five Tyler size ranges).

Jan 1, 1987