Search Documents

By E. J. Jacques

A typical problem in ventilation networks with multiple fan systems is the possibility of them interacting. Multiple fan systems are no exceptions in complex tunnels, and may also be met in mines where underground fans are installed. When aiming at controlling a multiple fan system in a ventilation network, e.g. with a view to maintaining an acceptable air quality level, yet at minimum power consumption, transient flow conditions frequently occur. Although in most applications these transients are short compared to the time needed to achieve the planned actions on the ventilation, one should, however, keep in mind that it is important to avoid any bouncing effect between different (adjacent or distant) fan systems. Therefore a simulation of the unsteady-state flows could allow us to learn more about the propagation of transients within the network, and their possible secondary effects Among others, one question that often is raised, is to find out in which sequence and at what time schedule each of the fans in a network should e.g. be started up? Another typical problem, into which an unsteady-state simulation could provide some insight is the following: how should the facilities of variable pitch angle and/or changeable RPM of several fans operating in parallel be handled and combined in order to obtain a flow rate that changes gradually from zero to its maximum value i.e. the sum of the individual throughput flows of all the fans. The literature is not very abundant on the topic of simulating transient flows in networks. There is no doubt that numerical models have been developed (Pollak, Christensen, 1987), most of the time for particular applications (Wala, Kim, 1985), (Tanaskovic et al., 1984), (Schultz, Sockel, 1991), etc. The aim of this paper is to present a model that also simulates one-dimensional compressible flows in unsteady-state conditions with, however, the specific intent to handle networks with more than one fan. PROBLEM STATEMENT The mathematical model chosen to describe the unsteady flows in a ventilation network is based on the dynamic and continuity equations applied to each of its airways. The following basic assumptions are made : - the flow in the airway is considered to be one- dimensional, - - the flow is assumed to be fully turbulent, and hence the ATKINSON equation for calculating the friction losses will be applied. Whether this equation remains valid for transient state flows remains an open question. However, this may reasonably be assumed since the interesting flow frequencies are low. A discussion may be found in (Kämpf, 1987) ; - the airways are assumed to have a constant cross- sectional area along their length. If obviously this would not be the case, it is always possible to subdivide the concerned airway into sections for which the previous assumption holds. Applying the basic equations of mass and energy conservation, the flow in each branch may be described by the Euler equation for Newtonian flows.

Jan 1, 1995

By Harry Elkin

Control of coal dust has long been an important aspect in the conventional mining of coal; the main reasons being from a health and disaster standpoint. With the advent, of mechanized longwall mining, the control of dust has required more attention due to the high extraction rate common to most longwall systems. The purpose of this paper will be to describe the dust abatement activities of the longwall operation at Sunnyside. Kaiser-Steel Corporation has three mires located at Sunnyside, Utah, with a total production averaging 6,800 tons of clean coal per day. Of this 6,800 tons, 71 % is mined with continuous miners, the remaining 29% coming from one longwall unit located in No. 3 Mine. Our first longwall panel was started in November, 1961. In October, 1966, we started mining our seventh panel. The present panel is located in the Upper Sunnyside Seam which averages five feet in thickness, but does get as low as 51 inches. The seam pitches 5.5% in this vicinity. The roof is generally good and is comprised of 10 inches of shale cap rocs overlain with sandy shale and sandstone. The floor is sandy shale and is quite undulating in nature. The present panel is 3,800 feet in length with a face of 670 feet. The major equipment employed on our longwall unit is a 125 H.F. Anderton Shearer-Loader, British Jeffrey Diamond armored conveyors and a Dowty self-advancing-roof support system. The Anderton Shearer in use on our longwall unit has a 60" diameter x 27" cutting drum. During the shearing cycle, it traverses the face at 20 feet per minute with a cutting rate of 7.5 tons/minute.

Jan 1, 1967

By F. Woller

The territory of Czechoslovakia is well endowed in deposits of a variety of industrial minerals. At present, 29 different types of industrial minerals are mined from some 600 individual deposits in Bohemia and Moravia only. About half of those production centres involves structural materials like aggregate and common brick clays and loams. A significant proportion of industrial minerals produced in Czechoslovakia are exported. Destinations of main products are shown in Figure 1. Production of industrial minerals in Czechoslovakia has a long history. Glass has been produced since the 14th century, sulphuric acid since 1578, graphite since 1750, and chinaware since 1790, to name just a few; but most of the present production comes from deposits developed during the past forty years. For a variety of reasons, only about 30 per cent of registered and explored industrial minerals deposits in the country are in production (Table 1). Two of the reasons may be the complexity of processing or conflicting interests of parties involved, but lack of market research, investment funds, or processing capacity have also had an impact on the level of utilization of the resource base.

Jan 1, 1992

By Ronald I. Fuller

Core Laboratories, a division of Western Atlas International, maintains laboratories in all energy-producing areas of the United States, as well as in many foreign countries. Central to laboratory operations has been the incorporation of computers and computer software. Core has developed a mu1tiuser Laboratory Information Management System (LIMS) , which is currently installed in numerous company sites in the U.S., and is now undergoing installation in Canada. In addition, Core has provided custom soft ware to contract laboratories which Core operates on behalf of mining firms. The software development was done under the direction of the author in Denver, Colorado, and Casper, Wyoming. The intent of this paper is to pass some of the practical experience gained by our efforts on to those who wish to utilize computers more fully in the laboratory setting. The product of analytical laboratories is numbers. Nothing else comes from our work. We deal in information about samples. It is then reasonable to assume that the computer would be central to a laboratory operation. The hard part is to initially define what kind of computer the lab operation needs. The choices today can be very complex, and almost every hardware salesman is full of bad advice. Even the people in your own information services department may hold divided opinions. Since the advent of the personal computer, we have lived with a polarized data processing community. The PC boys consider their machines equal to any challenge, while the "save the mainframe" crowd view the PCs as limited toys that are only good for the things that clutter up a real computer. Management tends to lean toward whatever costs the least.

Jan 1, 1989

By Paul F. Richardson

Liquids containing suspended solids are encountered in most mineral processing applications. Solids levels cover a very wide range, from ppm levels in cooling water systems to slurries containing greater than 70% solids. When the aqueous phase is recycled or further processed, a solid/liquid separation process is used. Chemical additives used to carry out this process are called coagulants and flocculants. In other cases, one seeks to control or modify the properties of the suspension. Dispersants are chemicals used to aid in suspending solids in a liquid as well as to control the properties of the resulting suspension. Dispersants find a range of uses in mining and mineral processing such as scale control, filter aids, flotation aids, and slurry viscosity modification. Materials used as dispersants include inorganic salts, alkalies, organic surfactants, and polyelectrolytes. This paper discusses the use of dispersants in mineral processing, with an emphasis on control of slurry viscosity. The mechanism of dispersion and factors that affect the choice of dispersant will be discussed.

Jan 1, 1986

By Keith A. Yarborough

INTRODUCTION The National Park Service (NPS) conducted a research program from mid-1975 to early 1978 to measure alpha radiation levels in natural caves which it administers. Subsequently, a long-term management program was developed which has conducted routine monitoring of radiation levels and has computed employee exposure accumulations in certain NPS caves. The overall program: research and management; was undertaken to evaluate the possible health hazard to cave visitors, interpreters, researchers, maintenance personnel, concessions employees and other workers and to protect their health. The results of this work have been reported extensively elsewhere (see References 1 through 3, 5, 6, 9 through 13, and 14 through 26). This paper deals with the relation of radon gas and daughter produced radiation levels to the cave air flows which mobilize them. These flows are a function of interior cave and exterior ambient air temperatures and pressures and of the cave's geophysical configuration. The low-level, ionizing radiation is produced by minute concentrations of radon and thoron gases which emanate from within caves. Because of confinement, the radiation levels are often appreciably higher than in surface atmospheres. Subsequent radioactive disintegration of the gases into their ionized "daughter" products, which are particulates, permits distribution of the alpha radiation throughout a cave system. The extent and character of this distribution depends upon the particular cave and the air flows which it produces. Thus, the alpha radiation serves as a "tracer" to describe the flows. The flow analysis is divided into two parts: 1) A qualitative description with respect to the two basic geophysical cave types over both long-term (annual) and short-term (diurnal to weekly) periods. 2) A quantitative description of the unsteady, uniform and non-uniform, one-dimensional, incompressible motions for both influent and effluent air flow situations in both basic geophysical cave types. A part of the qualitative description presents "Special Measurement" data: Tsivoglou [vs.] Kusnetz working levels, Tsivoglou individual daughter levels and free ion concentrations, radon gas concentrations, and equilibrium ratios. A great deal of important work has been carried out by Mr. Bobby C. Carson, Cave Radiation Technician at Mammoth Cave National Park, Kentucky. He reports these findings later in this conference (Ref. 6). Some of his results have been used here to establish the cave air flow analysis. Other National Park Service personnel have made measurements at others of the caves for which data are reported here. All of this work and cooperation has been vital to the success of this research program. It is very much appreciated. THEORETICAL FLOW DESCRIPTION Previously reported research (See Ref's. 20, 21, 23 and 25) has established the qualitative relationship between the alpha radiation in caves and their natural air flows. The radiation serves as a representation of these air flows. Changes in radiation with time represent changes in the main forces which produce the air flows. The quantitative data have substantiated that [all caves in which the primary cause of air flow is due to temperature produced gravity (density) gradients and also having minimal man-made disturbances, experience seasonal variations in airborne alpha radiation. The radiation levels increase in summer but decrease in winter], based upon seasonal air movements through each cave system which occur naturally. Two general types of physical cave configurations which control the air flows have been identified as: 1. Those which go up into a hillside or mountainside: Type I ("Upside-down" = USD). 2. Those which go down into the earth; Type II ("Right-side-up" = RSU). These act to control the air flows seasonally. The summer increase in Type I caves is due to increased air flows, whereas in Type II caves it results from stagnation or reduced air flows. This seeming paradox is explained by the physics of the air flow regime in each cave type and has been detailed elsewhere [Ref's. (20), (22) through (25)]. It[ i] true, in general, that air flow decreases airborne radiation in the [immediate vicinity] in which it occurs. Any paradox results from subsequent distribution throughout the case as to [ how] the air moves through a cave [system] with respect to time and space. Exceptions to the cave air flow "rule" are: 1. Caves in which pressure gradients and pressure fluctuations [predominate] in producing the air flows. 2. Caves in which man-made effects and management practices are superimposed on the natural air flow regime. Man-made disturbances which can alter the natural cave air flows are tunnels, elevator shafts, bore holes, sealed and closed portals, etc. If these are not properly sealed, the natural air flows which they change will totally alter the distribution and seasonal variations of the alpha radiation levels. These exceptions may act separately or in combination.

Jan 1, 1981

By Russell G. Hood

Rock bolting or anchoring are methods of stabilization which are not being fully utilized in California and probably in other parts of the world due to lack of understanding of the principles, or due to poor results in actual installation. The problem is greater in California because so much of the rock is either soft or badly fractured and broken. Almost any recognized type of rock bolt or anchor will perform successfully is hard, fresh rock, but the problems become many-fold when working in decomposed granites, shales, soft sandstones or other soft, highly-broken rock. There has been an enormous amount of research by manufacturers, consultants, private organizations, and governmental agencies on rock bolting. It would be impossible to discuss all the methods and philosophies of rock bolting in this paper. Therefore, with the indulgence of the experts, I will give only a very generalized coverage on rock bolting techniques. However, My main purpose is to point out some of the problems of rock bolting in soft rock.

Jan 1, 1967

By Fred T. Towne

There are a number of air classifiers manufactured throughout the United States and the rest of the world. The classifiers manufactured by Alpine, A. G. of Augsburg, Germany, are unique in their abilities. It is this uniqueness that I wish to delve into and in this respect we will limit this discussion primarily to the classifiers as manufactured by Alpine. It has been reported in the past that these classifiers were introduced into the. United States in the late 50's. Until the introduction of the Alpine Classifiers, air classification seldom produced a satisfactory fractionation of a product below 45 microns (325 mesh) or above approximately 22 mesh. It has been a common practice to classify fine materials which used water as a carrier medium The use of centrifuges are today producing thousands of tons of finely partitive powders in the very small particle size range. The use of centrifuges in connection with wet grinding mills has increased the rates of production of these mills considerably.

Jan 1, 1965

By James M. Neilson

In contrast to the rather generalized title of this paper, the subject of discussion will deal with two specific cases of sliding in glacial lake clays in northern Michigan. The slides in question occurred on lands owned by the Upper Peninsula Power Company a short distance south of Lake Superior. Slope failure problems have plagued the Company's operations for many years. It is hoped that this paper may provide some insight into the causes and possible mechanisms of clay slides in general as well as providing details of the two slides specifically cited. LOCATION The Upper Peninsula Power Company's Victoria facilities lie in section 29, T. 50 N., R. 39 W., in Ontonagon County, Michigan. The power site is situated on the West Branch of the Ontonagon River, approximately five miles southwest of the town of Rockland and only one mile to the southeast of the old mining location of Victoria. The area lies wholly within the Precambrian Shield and it is geologically similar to adjacent parts of Wisconsin, Minn¬esota, and Ontario. (Figure 1). THE VICTORIA HYDROELECTRIC SITE The Victoria hydroelectric power facilities were constructed in 1930 on a portion of the West Branch where meanders are conspicuously developed. The generating station is actually sited on an abandoned meander at a place where valley widening has occurred. Water is conducted from Victoria Dam through a 6000-foot, 10-foot diameter wood stove pipe - through a surge tank - and into the powerhouse where

Jan 1, 1971

By J. I. Schoenherr, T. A. Baloun

Mixed cable waste, which amounts to more than 200,000 tpy in Germany, is subjected to recycling. In most cases cable recycling means only recovering copper and/or aluminum metals. The remaining cable waste contains nearly 3-8% of the reusable materials, and is disposed of in landfills. Aluminum is recovered within copper products and leads to lower product prices. Preliminary laboratory tests show that the use of shaking hydro-tables as well as electrostatic separators result in less than 1 % of metals in the residual material. The products are high in grade at metal recoveries of more than 85%. Furthermore, applying a modified electrostatic separator may also lead to an efficient Cu-Al separation. The separation efficiency amounts to up to 95%.

Jan 1, 2002

Since the Rio Declaration on Environment and Development in 1992 in Rio de Janeiro and the publication of the agenda 21, the concept of Sustainable Development has become one of the major issues for governmental politics, societal developments and entrepreneurial policies. Current projects that deal with Sustainable Development in the mineral raw materials sector mainly focus on large-scale mining operations - especially for open pit mining - or on artisanal small scale mining. Artisanal small scale mining is in this connexion characterised as non-mechanized and mostly illegal mining activities. The number of workers is mostly far below 20. However, until now there exist no assessments or analyses with respect to the actual or potential contribution of industrial small scale mining to sustainable development. Industrial small scale mining refers to high technology or highly mechanized/automated extraction of small, high-grade deposits that due to their small size ? in combination with geological, depth and other constraints ? are not economically exploitable with large-scale mining operations. The Institute of Mining Engineering I and the Institute for Processing of Mineral Raw Materials at the RWTH Aachen University in Germany is currently conducting a research project financed by the German Research Foundation in order to investigate this issue. In the course of this project the sustainability of industrial small scale mining will be assessed. Therefore sustainability indicators, an assessment system and recommendations as well as options for actions and policies will be developed, in order to evaluate current industrial small scale mining activities as well as the potential for future developments in industrial small scale mining, both from a technological as well as from the point of view of sustainability, considering economical, social and environmental chances and risks.

Jan 1, 2007

By J. Luxford

The last decade has seen an enormous increase in the use of contractors right across the Australian mining industry. So much so that contractors now operate 33 of the 68 underground metalliferous mines around Australia and are making significant inroads into iron ore in the west and coal in the east. Safety used to be a low priority for many contractors. The picture has changed dramatically in recent years as most contractors take a far more professional approach to safety management. This paper examines the changes that have occurred and the requirements for effectively managing safety in a contracting environment.

Jan 1, 2000

By J. Donovan Jacobs

Many improvements in the art of underground excavation have appeared during the past two decades. These improvements have been both in methods and in machinery and have resulted in more economical construction of today's tunnels. In the realm of machines, the developments of continuous boring heads for either soft ground or rock, random arm excavators and the sliding tunnel floor (Magic Carpet) have each made contributions toward more rapid tunneling. CONTINUITY OF ADVANCE Tunnel boring machines are often referred to as "continuous excavators". Continuous advance (without cyclical interruptions) has not been achieved, however, in any of the machines now in use. In most rotary-head tunnelers the thrust needed to make the cutters bite into the face is obtained from hydraulic cylinders reacting against anchoring devices held stationary by pads which grip against the sides of the tunnel. With this system the forward motion of the cutting head is continuous only until the propelling cylinders have reached their limit of extension. At this point the grippers must be released, moved forward and reset before a new cycle of advance can be begun. Some machines are built to obtain their propelling thrust from hydraulic cylinders pushing backward against newly-installed rings of tunnel support. This is the customary method for propulsion of shields. With it, each cyclical advance or "shove" must await the erection of a new ring of supports. Faster tunnel driving

Jan 1, 1974

By W. B. Beerbower

Resin bolting has enjoyed wide acceptance for coal mine roof support. Beginning in 1973, the first year of significant resin bolting in coal mines, we estimate that 2.5MM resin bolts were installed. This grew to 7MM resin bolts in 1974 and 13MM in 1975. Resin bolts are currently being used in over 300 coal mines throughout the major coal producing areas of the U.S. and barring major work stoppage we expect more than 17MM will be installed in 1976. Although not a cure-all, the number of unintentional roof falls occurring in many mines has been dramatically reduced as a result of converting to this "new" method of support. 1 The improved anchorage strength of resin bolts provides better roof support. (Slide #1) This anchorage strength provides a mechanism to resist changing roof stresses along the entire length of the fully grouted resin bolt, thereby assuring stabilization of rock strata over long periods of time. The ability to resist roof displacement is borne out by readings obtained from strain gauged bolts. These findings can be summarized as follows.2

Jan 1, 1977

By F. R. Corwin, M. S. King, R. W. Zimmerman

A model has been developed to relate the velocities of seismic waves in unconsolidated permafrost to the porosity and the extent of freezing. The permafrost is idealized as an assemblage of spherical quartz grains imbedded in a matrix which itself is composed of spherical water inclusions in ice. The theory of Kuster and Toksöaz, based on wave-scattering considerations, is used to determine the effective elastic moduli, and hence the wave speeds. The model predicts Vp and Vs to be decreasing functions of both the porosity and the water/ice ratio, and Vp/Vs to be an increasing function of these two parameters. The theory has been applied to laboratory measurements of shear and compressional wave velocities in thirty-three permafrost samples from different sites in the North American Arctic. Although no direct measurements were made of the extents of freezing in these samples, the data are consistent with the predictions of the model. The theory can be used to infer the extent of freezing of the water in the pore spaces, based on knowledge of the porosity and either of the two wave speeds.

Jan 1, 1986

By Ahmet Tezcan, Zeki M. Dogan, Yalçin Kaytaz

Autogenous grinding in Turkey was first applied to quartzite where the mill is grate discharge type with an internal diameter of 2.99 m, having a length of 3.20 m and a capacity of as to 11.0 tons per hour. The second autogenous grinding was applied to a copper ore at Murgul Cakmakkaya Flotation plant of (KBI) Black Sea Copper Works having three mills 26 feet in diameter and 10 feet in length in close circuit with hydrocyclones. Recently, alterations were made in grinding circust by adding pebble mills. Furthermore, rubber liners and lifter bars were introduced pebble extractor and classifier were new features in the primary mills and circulating load was reduced by 20-50 tons per hour. At the end of these charges, capacity of each mill line was increased to 48 tons per hour with a full capacity of more than 9000 tons per day. Thirdly, autogenous grinding has been executed successfully on the slags of Samsun Smelting Plant of (KBI) Black Sea Copper Works with a mill of 20 feet in diameter and 6 feet on length having pebble mill following autogenous grinding.

Jan 1, 1992

By Jennifer B. Leinart

With the signing of the North American Free Trade Agreement (NAFTA), Canada, the United States and Mexico entered into an international experiment in economics amid a cloud of controversy that still lingers. Central to the controversy are the disparities in wages that exist among workers in the signing countries. Wage surveys completed by Western Mine Engineering show the degree of disparity that exists among the mining industries of those three countries. Labor costs constitute 30% to 50% of operating costs. So these wage differences are a matter of interest to the mining industry. It is unclear how much of a factor they are in determining where companies search for and develop new mines. That depends on where minable deposits are expected to be found. However, a deposit that may not be minable in the United States or Canada may be minable in Mexico because of lower labor costs. Some adjustments are anticipated for the Mexican mining industry if and when its wages begin to approach comparability with US and Canadian wages. Table 1 combines the results of four recent surveys. It lists benchmark wages for mining job titles common to all the countries. About 220 mines are covered by the combined surveys. Canadian miners' wages, converted to US dollars, are typically 75% to 95% of US wages, while Mexican miners' wages are less than 10% of those in the United States. Table 1 also shows that wage disparities are not confined to international borders. In fact, the difference in average wages between the US coal industry and the US metal and industrial mineral industries is greater than between the Canadian and the US mining industries overall. Table 2 shows that managerial, technical and administrative salaries show similar, but less pronounced differences among the three countries. Salaried personnel at Canadian mines earn 80% to 90% as much as their US counterparts, while those in Mexico earn 20% to 30% as much. Here again, average US coal salaries exceed average salaries for the US metal and industrial mineral industries.

Jan 1, 1998

By Roshan B. Bhappu

In situ mining and extraction is one of the Frontier Technologies that is destined to play an increasingly important role in the recovery of metals and minerals in the future. This premise is based on increasing costs of labor and energy, increasing awareness of environmental considerations and decreasing ore grades in the United States. Up to now, in situ mining has been successfully applied to a few favorable situations for the extraction of some evaporites, copper and uranium. However, because of its unique technical, environmental and economic advantages, this versa tile technology will find broader applications for the recovery of above commodities as well as for others which are currently extracted by hydrometallurgical means. This paper traces the development of in situ mining and extraction; stresses its dependence on interdisciplinary science and engineering; discusses its theoretical, practical and economic aspects; and finally presents potential applications of this Frontier Technology.

Jan 1, 1985

By Don Dodds

Iron Mountain Mine Rehabilitation Project Brief History The Iron Mountain Mine is located in Northern California approximately 12 miles northwest of Redding. The ore body is a large, very dense pyritic intrusion, discovered in 1860, and initially minded for silver. The silver played out quickly and 34 years later the ore body was mined for copper. Copper mining was scheduled to cease in 1939, but WWII prolonged the closure. After WWII, the pyrite ore was mined to produce sulfuric acid. In 1949 when large amounts of cheaper sulfuric acid were being generated by the oil industry the underground mine shut down. Little was done with the site conditions until 1970 when the U.S. Bureau of Mines began monitoring the pH of the effluent. The initial pH readings were around 2.0. This was lower than anyone expected. Laboratory tests showed that when the ore from the mine was submerged in water, the pH of the water would stabilize above 4.0. However, the pH got steadily lower. In 1989 with the ph around 0.7, the U.S. Environmental Protection Agency (EPA) required the owner to build a capture and treatment facility. During this initial period, the majority of the effort was spent on the treatment plant. The relationship between the mine owner and the EPA was basically an adversarial relationship from the very beginning. In 2001, North Pacific Research was hired to upgrade the capture and control facility. The general layout of the Iron Mountain Mine is shown in Figure 1.

By J. W. Merks

Applied statistics provides scores of powerful tests and techniques that are widely used and abused in science and engineering. The variance is the basic measure for variability, precision and risk. The formulas for the variances of the arithmetic mean and the weighted average are derived from the variance of a general function, as defined in probability theory. The requirement of functional or mathematical independence in probability theory translates into the concept of degrees of freedom in applied statistics. Geostatistics is the only variant of statistics in which functional dependence and degrees of freedom are irrelevant. This paper examines whether such basic elements of probability and statistics can be ignored with impunity.

Jan 1, 1998