Search Documents

By Ted C. Mathews

Pre-concentration by sorting is as old as the mining industry. Inevitably waste rock is broken with ore. Separation may take place in the stopes by selective mucking and transport, or selective loading and transport of ore and waste by 12-cu, yd. shovels and 100-ton trucks in large open pit operations. Hand sorting of 1" to 16" pieces, formerly widely practiced at underground chutes and prior to or following first stage crushing, has greatly diminished in the United States with its high per hour labor cost, although still widely practiced in other countries and, surprisingly, in some of the most modern mills where inexpensive labor is available. The economics of pre-concentration by sorting is attractive since elimination of waste at any cost less than the total milling cost will show a profit. The size at which sorting should be under- taken is determined by the size at which liberation is secured to yield a product of ore and waste, and greatly influences cost and the point in the flowsheet where sorting can be undertaken. In some instances mining costs can be reduced where an inexpensive sorting system to eliminate waste is combined with a less selective and less costly mining method. This is particularly true in deep mines where hoisting capacity determines the rate of extraction and sorting is performed underground, with waste utilized for fill. Hand sorting, while efficient, is expensive because of low sorting rates. Peale (1) quotes man hour capacity at 1/3 ton per hour on sizes 3/4" to 3" copper ore, and up to 5 tons per hour on rich iron ore sized from 4" to 16".

Jan 1, 1974

By Neal Rackstraw, Mamo Meaza

Washington Metropolitan Transit Authority Section E8a consists principally of twin tunnels 1,713 meters (5,620 ft) long, excavated to a diameter of 6.35 meters (20.83 ft) using an open face shield, with a primary lining of four unbolted precast concrete segments expanded at the crown, and a full circle unreinforced concrete final lining with a finished tunnel diameter of 5.08 meters (16.67 ft). The tunnels, constructed in Cretaceous age sediments, are mostly in stiff to hard clay except for a few areas along the alignment that contain dense to very dense fine sand in the upper portion of the tunnel that created a mixed face condition. At two locations unexpected heavy water inflows produced very serious problems in both tunnels. Water flows in the interface area were generally more than 378.5 1pm (100 gpm) and reached as high as 2,649.5 1pm (700 gpm) in the mixed face ground. The nature of the tunnel inflows, the consequences, and the corrective measures adopted will be the subject of this paper.

Jan 1, 1991

By B. P. Sullivan

This paper describes how the author projected the economic benefits of a proposed coal liquefaction project based in Pennsylvania. These benefits were assessed in a successful effort to garner government support for the project. The projections considered such issues as increases in employment, wages, and tax receipts to state and local government, plus other less-obvious benefits, such as site remediation. The paper explains how sponsors of similar projects can use economic projections in making meaningful and compelling presentations to federal, state and local authorities.

Jan 1, 2000

By Ronald E. Heuer

The significance of surface settlement over soft ground tunnels is well recognized. Cracked buildings, streets transformed into lakes, broken utility lines, to underpin or not to underpin--all are familiar problems. The basic causes of surface settlement are recognized. Possibly the most common and troublesome cause is "lost ground" during construction. Lost ground refers to removal of a larger volume of ground (Ve) than is eventually occupied by the final tunnel structure (Vt). A number of sources of lost ground in shield tunneling have been identified, as illustrated in Fig. 1. These include 1) face loss, 2) overcutting loss, 3) annular tail void loss, and 4) loss through the lining. The ground generally does not stand unsupported around the completed tunnel lining as illustrated in Fig. 1, but moves in to fill the lost volume, resulting in subsidence of the overlying ground surface as shown. As suggested in Fig. 1, lost ground and surface settlement associated with overcutting and the annular tail void tend to occur systematically along the tunnel length. This "systematic" lost volume is "limited" in the sense that it is restricted to an upper limit determined by the shield and lining geometry. Partially controlled face loss may sometimes contribute to this systematic loss. This lost volume is commonly a few percent of the nominal tunnel volume. The resulting surface settlement over the tunnel is commonly in the range of a few inches or less and develops over a period of hours to days. Although they may have a significant impact on surface facilities, systematic ground loss and settlement frequently have little adverse effect on tunneling progress.

Jan 1, 1976

By Alexander Karim

This paper reviews the growth pattern in bauxite and alumina production, and primary aluminum smelting through 1980. Because the alumina and primary metal are intermediate products of the major integrated aluminum companies, it is not possible to determine their production costs. The costs indicated in this paper are order of magnitude costs based on published figures and the market price of these products. The conclusions in this paper indicate the general pattern of growth in the aluminum industry and are not meant to be a substitute for the feasibility and economic studies that are needed for individual bauxite mining, alumina refining and aluminum smelting projects.

Jan 1, 1968

By Ronald T. Cosburn

The Province of Ontario covers an area of some 400 thousand square miles, however the subject I will be talking about today, the licencing of pits and quarries in southern Ontario, refers to about one quarter of this total area but contains better than 93% of the total population of the province or about 8 million people. Southern Ontario had and still has many inviting features to industry. The Great Lakes almost surround us, hydro power has been relatively inexpensive and abundant, but more in line with our topic today are the ample deposits of sand, gravel and limestone, all of which are used directly or indirectly throughout and are the mainstay of our construction industry. I say we are fortunate to have these non-renewable resources in abundance in close proximity to our industrial and metropolitan areas, but like so many of our resources we have taken them for granted for too long. What has happened in our case, as I am sure is common in many of your own similar situations, because of the recent, current popular trend by naturalists and environ- mentalists to preserve our natural heritage at the expense of all else, through parklands and indiscriminate zoning policies, these once abundant reserves have been tremendously eroded.

Jan 1, 1982

By Martin Herenknecht, Michael Knabe, Ulrich Rehm

In Switzerland at present, the longest railway tunnels in the world, the Gotthard(57 km) and the Loetschberg base tunnel (34km) are under construction. For thischallenge six high-tech HERRENKNECHT Hard Rock Tunnel Boring Machines (TBM)are applied, which have to excavate approx. 80 km at the Gotthard and 20 km at the Loetschberg Tunnels. The machines being used are of a single Gripper-TBM type, which are equipped with the latest rock support techniques, in order to optimize the quality of the working conditions for the personnel which have direct impact on the quality of the tunnels. The different requirements of the projects based on different speci?cations within the tender documents led to completely different TBM concepts which will be reviewed in detail in this paper.

Jan 1, 2003

By P. A. K. Wilkinson

This paper is concerned with the development of an in situ recovery of boric acid from a deep-seated colemanite deposit in California. The deposit contains 147 million tons of borate ore containing 6.4% boron oxide (B203). It is the largest undeveloped colemanite deposit in the United States and because of its unique occurrence and grade, in situ extraction appears to be the most economic viable process. The paper covers the geological, mineralogical, hydrological, well-field development, and extraction considerations leading to the initial pilot plant and subsequent demonstration plant phases of the project. Market potential aspects and preliminary economics of the project are also covered.

Jan 1, 1987

By Preusse. Axel

Underground coal mining can cause seismic events. There is currently no way to predict such phenomena reliably, in particular stronger events. That is why, according to the current state of the art, empirical methods are employed in this field. Some assessment criteria, which relate to the geological and mining situation and either stimulate or rather help to avoid seismic events, are presented in this paper. These criteria are examined for a practical mining situation in Germany, with a view to estimate possible seismic events.

Jan 1, 2009

By R. Hogg

Experimental studies of the axial distribution of particles along dry ball mills are described. The results, for mills ranging in diameter from about 10 cm to 1 meter and operated in both the batch and continuous modes, indicate a consistent pattern of significant migration of particles away from the ends of the mill. In some, but less frequent, cases axial migration of the grinding media is also observed. Analysis of the data suggests that particle migration results from end-effects which extend for a distance of about one mill diameter along its length. End-wall roughness appears to play a significant role in the particle migration phenomenon. Media migration is generally associated with continuous mills operating at relatively high powder flow rates.

Jan 1, 1994

By Bryan A. Bartley

High intensity, autogenous grinding has been developed in the hard rock, quarry industry and is finding wide application in mineral processing. The autogenous vertical shaft impactor is described and action within the machine is illustrated. This machine is compared with the cascade mill, in the three characteristics of impact, inter-particle rubbing and nipping, of which impact is the most important. There is a seven fold increase in impact level over that of the cascade mill. The autogenous impactor has characteristics of crushing and grinding, preferential crushing, abrasion resistance and drying. These are illustrated by examples of industrial applications, where the machine is now used and range from abrasives, such as Carborundum to phosphate rock.

Jan 1, 1998

By D. Brunner, G. R. Baiden, H. J. Yazici

System simulation is an increasingly popular technique for analyzing and improving existing as well as newly designed underground mining operations. An engineering firm that specializes in simulation helped a major metals producer build a long-range planning model of an existing underground mine. Subsequently the team adapted this model to assess technology alternatives in the design of a new mine. The two models differ in the level of detail used for modeling the development process. This paper discusses the differences in approach between the models along with the experiences gained and challenges faced during the construction and use of the models.

Jan 1, 1999

By Kostas Fytas

Canada still remains today a strong resource nation with a huge geological potential. Canada ranks among the top five leading countries in the production of 15 major minerals. Acid mine drainage (AMD) is a serious environmental problem that preoccupies the Canadian Mining Industry. Considerable amounts of money are spent every year in an effort to prevent or reduce the acid mine drainage production. It is estimated that across Canada there are a few thousand abandoned mine sites as a result of the last fifty years of mining. Most of these sites are acid producing presenting a serious threat to the environment. It has been estimated that the cost of stabilizing and reclaiming these sites across Canada will be over $5 billion over the next twenty years. Current practices for decommissioning acid producing sites are water covers (flooding), dry covers, revegetation and treatment of the acid effluents. This paper presents the technical and legal issues of mine closure and reclamation in Canada. The methods used in the revegetation of acid producing mine sites is also presented This paper also reviews the financial guarantee requirements for mine closure by the provincial legislations in Canada. A case study of stabilizing and reclaiming a sulphide tailings area in the Sudbury region is presented. It illustrates the challenges facing the Canadian Government and the mining companies in restoring and revegetating the closed and abandoned mine sites across Canada.

Jan 1, 2002

By Harry W. Barr

Judging by the inquiries that come to Battelle, a number of companies have run into problems in determining the size and character of markets for mineral fillers in general and specialty fillers in particular. Usually these problems arise during a project to develop a new mineral filler when management suddenly realizes that a considerable sum of money will have to be spent before any profits are realized from sales of the new filler. What management needs in this case is the odds for or against the success of the development. And these odds frequently are controlled by the markets for the new filler. Basically, the problems involved in gaging markets can be simplified to how much of this new filler can be used and by whom? But there are some potential booby traps in these simple questions that should be exposed. This paper will discuss a few of these problems such as: 1. Describing the filler so that the prospective customer recognizes its possible applicability. 2. Finding; a prospective customer who can verify the filler's applicability. 3. Expanding successful test results to total industry markets. 4. Appraising competitive products, and 6. Discovering all the possible uses for the new filler.

Jan 1, 1961

By V. Scovazzo

Cost-effective underground mine configurations have been designed in highly fractured rock masses where the stone possesses a high material strength. A limestone mine in the eastern United States is used to demonstrate procedures for the geotechnical design of one such operation. The mine discussed is located in both limbs and the axis of a recumbent fold that fractured the rock mass. In a highly fractured rock mass, where the host rock has high strength, a design can be developed to alleviate intact rock failure. This is possible because in most cases as the stress levels needed for intact failures are approached, the stresses are quickly dissipated due to movement along discontinuities, which represent planes of weakness. As a result most underground failures in highly fractured rock are due to sliding or toppling. Even when intact rock fails in a highly fractured rock mass, it is the movement along an existing joint or other weakness plane that often initiates or causes this failure. It is therefore important to obtain the characteristics of weakness planes that are the discontinuities within the mass. The required information on weakness planes, geology, and strength of materials is discussed and recommendations for obtaining this information are presented. A discussion is provided on failure modes and the use of developed information for their evaluation. The impact on geotechnical design is demonstrated through pillar sizing procedures; however, this approach can also be applied to mine roof and pillar foundations.

Jan 1, 2004

By Hassan Madani, A. Malek Mohammadi

Dorreh barite mine located in the central part of Iran is one of the largest barite mines, in the country. The mine is subdivided into three blocks, which are called block 1,2,3 according the barite quality. In the central part of each block, a heavily concentrated grid of exploratory drill holes have been drilled and the reserves of area was calculated based on these holes, some years ago. It was decided to compute the reserve of the area by geostatistical methods, in the form of an M.Sc. project. In order to study the area, three regionalized variables including density, thickness and density-thickness (accumulation) was studied and the spherical variograms were fitted to these variables. These models were evaluated by cross-validation method. The optimized block size was chosen in order to compute the reserves by kriging method. The reserves of explored parts of each block of mine was calculated and the results were extended to the whole area of the blocks. The reserve of the explored parts and the total reserve of the area were calculated to be 96,000t and 1,670,000t respectively.

Jan 1, 1996

By William J. Taylor

Strictly defined, a stull is an inclined or horizontal timber support; a vertically placed timber is defined as a prop. Common usage allows the catchall term "stull" to refer to all such uniaxial mine support, regardless of orientation. Typically a stull is a round wooden column that is wedged in place to provide short-term auxiliary support between sill and back, or between hanging wall and footwall. Stulls may be used exclusively or in con- junction with other support systems such as roof bolts, shotcrete, or cribbing. Stulls are used both as local temporary support in stoping operations and for uniform systematic support installations. Where stoping areas are to be abandoned soon after excavation, stulls may be used to provide temporary support during mining operations. Where controlled caving and subsidence is required, stull supports are designed to fail in a systematic, predictable manner. Wood type is selected on the basis of availability, price, and load carrying characteristics. Coniferous woods are typically used, especially to carry heavy ground loads. Brittle woods are generally avoided because of their tendency to fail suddenly. Gradual yielding failure is preferable to sudden, unexpected failure of the support. Some usage of wood from deciduous trees such as cottonwood and other poplars has been reported in Grants, NM. These stulls reportedly mushroomed as the ground load increased but continued to maintain their structural integrity. Stulls fabricated from structural steel are used in special applications. Adjustable lengths are commercially available in mechanical, hydraulic, and pneumatic designs. The high cost of mechanical stulls limits their use to mining systems where recovery and reuse is possible. End blocking, also called headboards or footboards, uses wood blocks that are placed between the stull end and the ground they are supporting. The blocks are typically 50.8 to 101.6 mm (2 to 4 in.) thick, 203.2 to 304.8 mm (8 to 12 in.) wide, and 381 to 609.6 mm (15 to 24 in.) long. End blocking serves to distribute the support over wider back area. Compression of the end blocking gives visual indication of wall movement prior to failure of the stull. A common application of the stull is in flat-bedded uranium mining during pillar extraction. Many western US uranium mines use a pillar pattern development to delineate the irregular ore pods. After development of an appropriate sized pillar, the ore pillars are then sequentially mined out, leaving the undercut hanging wall or back to cave. Where thickness of the ore is less than 4.3 m (14 ft), stulls are generally used to provide ground control as the pillar is removed in slices. Experience dictates the density of stull placement. In general, the number and size of stulls should be sufficient to resist ground closure and to provide support for drilling and loading operations adjacent to the pillar. Stulls next to the mining face are often lagged 0.9 to 1.2 m (3 or 4 ft) up from the floor (or sill) to confine the blasted ore to a passage next to the pillar. Mucking is simplified by this confinement. Experience dictates whether back control along a mining face requires removal of stulls to allow con- trolled subsidence of the back or hanging wall. Without caving or closure, abutment pressure can create poor ground conditions near the pillar.

Jan 1, 1982

By James L. Evers

Introduction There is a continuing search by government and industry for new mining methods that increase production, improve the working environment, reduce labor intensity, enhance recovery effectiveness, improve the reclamation process, streamline the flow of material, and reduce the unit cost. Hydraulic extraction and transport methods have outstanding potential in several of these areas. For example, hydraulic fragmentation produces a significant reduction in respirable dust. The inherent simplicity of hydraulic mining equipment and the resulting high reliability are recognized. Tool wear can be virtually eliminated. There is great flexibility in the size, shape, and orientation of the mineral deposit that can be mined. The cutting, gathering, and transport operation can be controlled remotely, providing more safety for workers. The threat of tool sparking and the resuiting dust or gas ignition are also eliminated. Although hydraulic mining was introduced in the US before the turn of the century, it has not gained the degree of acceptance found in other countries such as the Soviet Union, China, Germany, and Canada. The Hydraulic Mining Research program, initiated by the US Bureau of Mines in 1958, and the subsequent research by others has provided much of the basic technology required to spur the development of these methods into a viable extraction alternative. This article updates the development of hydraulic mining in the US. Particular attention is paid to monitor mining, the long-wall hydrominer, borehole mining, and the semi-autonomous mining system. Whenever the particular mining method is also being developed in other parts of the world, a brief description of the world-wide state of the art is given. Finally, allied studies designed to optimize these mining techniques are described. Hydraulic Monitor Mining Since 1958, the US Bureau of Mines (USBM), the Department of Energy (DOE), and other government agencies have funded more than a dozen programs to investigate the potential of hydraulic monitor mining. For this method, water is directed on the coal face from a monitor nozzle. Sufficient velocity is used to cause local fragmentation (Fig. 1). Coal particles are washed from the face to a trough. They are then flumed to a collection point. Oversized particles are directed through a breaker and then into the troughs. Monitor field tests were conducted in the 1960s in bituminous and anthracite coal at the following locations: • Rosylin No. 9 mine, WA (Nasiatka and Badda, 1963); • Rosylin No. 10 mine, WA (Price and Badda, 1965); • Sugar Notch mine, PA (Buch, 1964); • Thomson Creek mine, CO (Palowitch and Malinka, 1964); and • West Lebanon, PA (Fowkes and Wallace, 1968). In 1975, Ingersoll-Rand Research Inc. was awarded a two-year USBM contract to develop a continuous coal mining system using water jet fragmentation and

Jan 10, 1984

By Anthony Busigin, Charlett Busigin, Colin R. Phillips

For the purposes of measurement and dosimetry of airborne radon daughters in uranium mines and elsewhere, it is important to understand their physicochemical state. This work deals with the chemical fate of 218Po in air. Extensive experiments were performed to determine the rate of neutralization, diffusion coefficient and fraction born charged of 218Po in air. The experiments were performed in a specially constructed apparatus of well-defined geometry. Careful control of experimental conditions made it possible to obtain more precise and detailed quantitative data than previously possible.

Jan 1, 1981

By G. Tiess, S. Mujiyanto

Indonesia is a fast growing democratic developing country comprising more than 17,000 islands, founding member of ASEAN and a member of the G-20 major economies. It is one of the most highly mineralised countries in the world, the mining sector playing a pivotal role in the country's economy. In 2001, the Decentralization Law No. 22/1999 came into force and caused a transfer of authority and responsibility from central to regional and local administrative governments. The new Mining Law of 2009 substituted its 40 year old predecessor, but lacked detailed regulations for its implementation. These were only issued in 2010, which lead to a period of great uncertainty for investors in the mining industry. The new legislation intends to foster domestic economic development, which may be interpreted as protectionist policy. For the development of a sustainable mineral resources policy, further endeavours will have to be made.

Jan 1, 2011