Search Documents

By X. Wu, E. Topuz

Booster fans have been extensively used in underground mines throughout the world. In the United Kingdom, S. Africa, Germany, and other countries, many non-coal and coal mines employ booster fans. These fans help to reduce air leakage, to provide an improved flow distribution and to reduce the overall cost of mine ventilation. Although booster fans have not been used in coal mines in the United States, a recent survey indicated that many coal mines would install booster fans if they were allowed to do so. With the inclusion of coal mines, the use of booster fans in underground mines is expected to increase substantially in order to maintain air quality and quantity requirements. Several techniques are used, with varying degrees of success, in determination of booster fan locations in an underground ventilation network. These techniques include linear programming, critical-path crashing, CPM together with cutset operations, the out-of-kilter method, and simulation techniques. This paper provides a brief comparison of these techniques, and reports on ongoing research for an improved methodology for the determination of booster fan locations.

Jan 1, 1987

By James M. Barker

The borate deposits of Death Valley, first exploited in 1882, were a major world source of boron-bearing products until shortly after very large deposits near Boron, California (Kramer) came on stream in 1926. Borate mining in Death Valley then became moribund, with most extant deposits held as reserves backing Kramer. Tenneco began borate operations following acquisition of claims in 1967 and is the only active borate producer inside Death Valley National Mon¬ument. Borate ores, confined to the lower Furnace Creek Formation (early to middle Pliocene), initially precipitated in a shallow lake fed by boron-rich volcanic hot springs associated with the Basin and Range province. Later diagenesis and remobilization plus regional folding, faulting, and erosion altered and complicated originally simple borate mineralogy and distribution. Dominant ore minerals are ulexite (NaCaB509.8H20), probertite (NaCaB509.5H20), and colemanite (Ca2B6011.5H20). Tenneco currently operates two open pits near Ryan, California. Mining is by bulldozer-pushed scrapers hauling waste and front-end loader/off-highway truck combinations for ore and waste haulage. Archeological, environmental, and aesthetic considerations influence both mine plans. Boraxo Pit, opened in 1970, has deep ore (stripping ratio 10 to 13:1) which occurs along a fault and as beds in shale on the hanging wall. Problems include pit wall instability (adverse bedding), non¬ripable calcareous shale (11,000 fps), and mixed ore separation. Sigma Pit, opened in 1975, has shallow (stripping ratio 1 to 1). low dipping, bedded ore in shale. Massive ulexite and "granular" un- cohesive colemanite present problems in mining and milling. Colemanite is crushed to -6 inches, washed, dried at 350°F, then calcined at 800°F with 100 tpd capacity. Crushed (-6 inch) ulexite or probertite is Raymond milled to customer specifications with a capacity of 1000 tpd.

Jan 1, 1976

"It’s been 80 years since Charles Warman invented the iconic Warman slurry pump, a pump that revolutionized the mining industry and continues to push the boundaries of pump performance to this day.In honor of this legendary brand, Weir Minerals hosted an event at the end of May in Kalgoorlie, Western Australia. Throughout the evening, attendees relived Warman pumps’ history and gained an insight into some of the future innovations planned.“It was a privilege to share this special night with some of our key customers, past and present employees, and members of the Western Australian School of Mines,” said Ricardo Garib, divisional president of Weir Minerals. “Warman is one of our leading brands. It has truly shaped the mining industry over the past 80 years and is a product we are all very proud of. The Warman pump, invented to solve high wear issues in slurry pumping, created a thriving industrial business that is now the cornerstone of Weir Minerals with more than 8,000 people, and more than 150 manufacturing and service centers across the globe.”Always inventingCharles Warman invented the Warman slurry pump in Kalgoorlie in 1938. It was a hardwearing slurry pump that used replaceable liners and a replaceable impeller, something that had never been done before.“Charles Warman was a visionary and an innovator. The use of rubber lining in the pump was groundbreaking as it reduced total ownership costs, was safer to handle and offered extended wear life in many abrasive slurry applications. It is a great example of solving customer problems with material science, and is still taught in universities today,” said Marcus Lane, global product manager for centrifugal pumps at Weir Minerals.It was quickly adopted throughout the goldfields in Western Australia and by the 1950s, as customer demand rose, Warman expanded his business by opening offices in Sydney and Perth.During the 1960s the rapid growth of the business continued with manufacturing and sales outlets established around the world. The Warman Series ‘A’ pump was accepted and became a world leader in its field. Further work on the Warman AH pump resulted in the development of interchangeable metal and rubber wearing components."

Jan 9, 2018

By C. P. Wa1ters

This paper is written primarily from the standpoint of the miner and consumer of Missouri fireclays in refractory products, principally firebrick used in the linings of blast furnaces, hot metal transfer cars, the recuperators of glass melting tanks, and other allied uses involving contact with liquid metals and reactive slags. For these uses the manufacturing plant requires forecast of certain physical characteristics, as well as chemical characteristics, of the raw clays as a determination of practicability of mining, treatment such as pre -firing or calcining, and final usage area. These methods and results may leave something to be desired from an academic view, but are used my operation as an on-running guide to seeking and mining raw material. The high quality fireclays of Missouri are generally differentiated by the user as the softer, somewhat plastic, "bond" clays and the so-called flint clays suitable for a fired or unfired aggregate portion of a brick composition. The semi-plastic "bond" clays are mined in a producing area of northeast Missouri including Montgomery, Audrain, Callaway, Monroe, and Lincoln counties. In this geographic area the clays are the members of the cheltenham formation and occur in rather large lenses in which the usable members may approach 15 meters in thickness and an area of 6o to 8o acres. Overburden is dependent on the surface topography and, in our operations, varies from 8 meters to 25 meters. It can be up to 36 meters in the prairie uplands, but this is rarely strip mined. There was former mining by shaft and drift methods in which the overlying coal was also worked. These clays are primarily used as a binding material for other clay aggregates and is characterized by its lower refractoriness-cone 3o (165o c) to cone 321/2 (172o c), in terms of pyrometric cone equivalent, and an alumina - Al2o3 - content of plus or minus 31%. Physically, these clays are readily slaked by water to a fine grain size and exhibit a degree of

Jan 1, 1977

By H. M. Woodrooffe

In the U.S.S.R. three of the world's major-known phosphate deposits are located. These have an estimated reserve of 2,600 million short tons of contained phosphorus. The best known lies in the "Khibiny Massif', an alkalaic rock formation some 600 square miles in area with mountain peaks rising to an altitude of 3300 ft above the surrounding terrain. Location and Climate The Khibiny Massif lies north of the Arctic Circle in the Kola Penin-sula, 100 miles south southeast of Murmansk, at a latitude of 67° 30' north and a longitude of 35° 30' east. It is serviced by rail from Murmansk and Leningrad (900 rail miles south). Figure 1. The phosphate operations are centered about the two cities of Apatity and Kirovsk. The former has a population of 35,000 and is on the Leningrad¬Murmansk railway. Kirovsk, 15 miles to the east, is now a city of 85,000. The region is at the limit of the tree line with most of the ground cover typical tundra. The mean annual temperature is -4°C and, in a normal year, precipitation occurs on 240 days. Because the temperature does not exceed freezing for 300 days each year, virtually all of the precipitation is snow. The two towns are nestled between mountains and, because of the weather, extensive avalanche control systems incorporating major engineering construction have been introduced to divert snow slides away from the populated areas. General Kirovsk was first settled in 1923 and the apatite occurrences were recognized shortly after. In 1933, the first concentrator for the recovery of the mineral was completed, producing in its first year of operation 170,000 tons of concentrate. With the growth and demand for phosphate in the U.S.S.R., a second concentrator was erected at Apatity. It calve on stream in 1963. Because of the severe climate, in the early days mining was limited to 85 days per year. With the introduction of new techniques and improved mining methods, the season has been extended to 115 days.

Jan 1, 1972

By J. B. Hiskey, V. P. Atluri

Resin-in-leach (RIL) cyanidation experiments were performed on a refractory carbonaceous gold ore. The objective of this investigation was to determine if strong-base ion exchange resins could adsorb the soluble aurocyanide complex in preference to natural "preg robbing" organic constituents. Direct cyanidation of the carbonaceous gold ore used in this study resulted in less than 2% gold extraction in 24 hr. RIL cyanidation resulted in about 70% gold recovery onto the resin. Kinetic experiments indicated that 50% of the gold is extracted after 1 hr of leaching. Resin breakage was investigated for as-received and preattrited resins. Similar results were obtained with three different strong base resins.

Jan 1, 1990

By W Frint

An area in Southwestern Wyoming is rapidly becoming the soda ash capitol of the world. Starting only 20 years ago from a unique deposit of trona, the out-put has rapidly increased until now about half of the soda ash produced in the United States comes from this area. Chemically, soda ash is sodium carbonate, a large tonnage, widely used alkali. The largest single industrial use is in glass manufacture, where 25 tons of soda ash are used in producing 100 tons of glass. Other big users are the detergent and chemical industries. The trona deposits in the Green River basin of Wyoming, were formed about 75 million years ago as part of a geologic period when an ancient lake alternately went through periods of being a large fresh water or smaller brine lake. Today these deposits lie from 800 to 3000 feet below the surface in a semi-arid, almost desert region just west of the Rocky Mountain Continental Divide at an elevation of 6200 feet. In this area there is a prevailing westerly breeze and almost every afternoon the velocity reaches very windy conditions. Rainfall is minimal, being only 6-8 inches of moisture per year with an evaporation rate exceeding 24-inches. Most of the moisture comes in winter snows or summer thunderstorms. Temperatures are low with below zero weather dur¬ing most of the winter and early morning frost is not uncommon during the summer months. There are many trona beds varying in thickness from a few inches up to 15 feet. The deposits now being mined vary from 8 to 10 feet in thickness. The ore is mined by driving tunnels either via conventional explosives or with continuous boring machines. It is transported to the shafts via conveyor belts

Jan 1, 1972

By Patrick J. Doig

The contract for the construction of the Inline Pump Station for the Milwaukee Metropolitan Sewerage District involves the sinking of three shafts and the excavation of a pump chamber. The shafts are being sunk to a depth of 104 meters and pass through 52m of sediments before encountering dolomitic bedrock. The pump chamber is constructed in dolomite. The sediments are alluvial, estuarine and lacustrine in origin, with some ice margin deposits. They comprise loosely consolidated fine to coarse grained sand, silts, clays and gravels, and they are heavily saturated with a water content often above 60%. The water table is at a depth of 3m. The dolomite is silurian, generally dense, with some clay-filled vugs and shale partings. Until 1983, underground construction in the Milwaukee area had been limited to depths of 26m in the sediments and 20m in the dolomites. Water control methods had included caissons, compressed air, extensive internal and external dewatering, and grouting. Flows of 20 liters per second were commonplace with as much as 80 liters per second being encountered in the rock. However, in 1984 work was commenced on the deep sections of the Milwaukee sewerage scheme with the letting of three major contracts including the Inline Pump Station. With excavation taking place at greater depths, it become obvious that previous methods of water control would be inappropriate. To protect against major inrushes of high pressure water in the rock, an extensive program of pre-grouting from the surface was specified. Water control in the sediments was left to the discretion of the contractor and in each case freezing was choosen. This paper describes in detail the grouting and freezing procedures.

Jan 1, 1985

By M. P. McArthur

General mining practices at W. R. Grace's Bonny Lake mine are much the same as those used in open pit phosphate mines in Central Florida, except for the difference in the depth of the overburden which introduces many variations, From 1945 to 1961 the mining at Bonny Lake has been from an area in which the overburden averages from 55 to 60 feet and in several locations exceeded 65 feet. The matrix thickness will average 15 to 18 feet for the areas mined. As you can see from the above depths a total hole depth will average from 70 to 75 feet.

Jan 1, 1962

By T. Payne

Underground heat issues are mainly focused on the detrimental effects to a workers health. However, working in hot, humid conditions has other negative effects. Studies have shown that safety, productivity, workforce morale and operating cost are also worsened in these conditions. The human body has several mechanisms for rejecting heat and remaining cool. However, once the air temperature exceeds about 34°C, the only effective mechanism is by evaporation of sweat from the skin. This is assisted by acclimatisation which is the human body?s enhanced ability to combat extended exposure to heat. The body has to remain well hydrated when working in heat as even small degrees of dehydration cause significant decreases in the ability to work in heat. There are two ways in which heat load can be reduced: Through use of refrigeration/vent/cooling to reduce thermal stress on workers; Reduce the contribution that heat sources have to underground heat load (e.g. reduce idle time, fleet size, etc). Some of the sources of underground heat have the potential to be more manageable than others. Geothermal heat and heat from autocompression will be found in all mining situations in varying degrees depending on geothermal gradient and surface temperature, however, the use of equipment and blasting may be streamlined to reduce the underground heat load. It is through a combination of the available options that most mines will successfully control their heat related problems. Mt Isa, which has been a focus for heat related study in Australia, has successfully implemented protocols for working in heat. Through combining these with the installation of a surface bulk air cooling plant, Mt Isa has consistently reduced the incidence of heat illness. This is likely to be the most cost effective method of reducing heat load for deep mines in Australia. Shallower mines which may only occasionally encounter hot conditions should consider more portable cooling options. This study will review the heat issues in underground Australian metalliferous mines.

Jan 1, 2009

By T. C. Pool

Physical and chemical conditions permitting, in-situ leaching (ISL) of uranium offers a variety of advantages over conventional production methods including less surface disturbance and less solid waste. Commercial production of uranium by in-situ leaching techniques was initiated in 1963 in the Shirley Basin of Wyoming by Utah Construction. On a world-wide basis, ISL uranium production amounted to about 13.2 million pounds U3O8 in1999, approximately 16% of world output. Both acid and alkaline systems are used, the selection of which is primarily dependent upon groundwater quality and related reclamation requirements. ISL offers low capital costs per unit of annual capacity and is particularly flexible in adapting to changing market conditions.

Jan 1, 2000

By A. D. Davis, C. J. Webb, A. Heriba

Introduction The disposal of spent ore from cyanide heap-leach processing facilities is of concern to the mining industry, the regulatory agencies and the general public. The disposal of an additional several hundred million tons of spent ore from heap-leaching operations is planned in the western United States during the next decade, and this amount could increase if gold prices rise. In the past decade, more than fifteen million tons of spent ore have been disposed of in the Black Hills of South Dakota. The criterion for offloading spent ore was set by the South Dakota Department of Environment and Natural Resources at 0.5 ppm weak acid dissociable (WAD) cyanide. South Dakota's nitrate offloading limits vary for each mine, depending on ore type and other factors. Concentrations of nitrate in the leachate from spent ore depositories could be the result of conversion from other nitrogen-containing species. One likely source of nitrate is residual explosives from the blasting of ore. Previous work on the combustion products of nitrogen explosives has shown incomplete oxidation (Johansson and Persson, 1970). Another likely nitrate source is the degradation of cyanide to ammonia, followed by oxidation to nitrite and nitrate. A third possibility may be leaching of background nitrate from soil or rock. Objective The primary objective of this research was to investigate laboratory procedures for predicting nitrate concentrations in effluent after the disposal of spent ore at heap-leach gold processing operations. Laboratory tests were performed to define the concentrations of nitrate and nitrite in leachate as a function of time. Sources and species conversions were examined by investigating the nitrogen contributions from cyanide neutralization and from blasting with ammonium nitrate/fuel-oil (ANFO) explosives. Ore processing at cyanide heap-leach facilities Gold mines in the northern Black Hills of South Dakota normally use the following steps in their heap-leach cyanidation processing: Blasting. Surface gold mines in the Black Hills use ANFO explosives (approximately 95% ammonium nitrate and 5% fuel oil). Field evidence and studies show that explosives often fail to ignite or burn completely in shot holes. One reason is that ammonium nitrate absorbs moisture readily, which reduces blast efficiency. Ferguson and Leask (1988) cited a study conducted at the Fording coal mine in southeastern British Columbia. In that study, the total nitrogen released to surface and ground water was estimated to be about 6% of the slurry explosives. However, Ferguson and Leask (1988), in a later analysis of water quality near coal mines in the Kootenay coal fields, indicated that this is likely an overestimate of the nitrogen release. Mines that used ANFO explosives in dry conditions released 0.2% of the nitrogen from blasting. Cyanidation. At surface gold mines in the northern Black Hills, cyanide species from heap leaching can be classified into free cyanides and simple ions, weak complexes, moderately strong complexes and strong complexes (Scott and Ingles, 1981). Degradation of cyanide and disposal of spent ore. Methods of destroying cyanides include hydrogen peroxide oxidation, natural degradation and evaporation, water leaching and alkaline chlorination. Hydrogen peroxide is used to oxidize cyanides in the northern Black Hills mining area. The hydrogen peroxide oxidation reaction forms cyanate, which can hydrolyze to form ammonium and carbonate ions. After formation of ammonia or ammonium ion, further oxidation to nitrite (NO2-) and nitrate (NO3-) can occur. Spent tailings from gold processing in the Black Hills normally are disposed of in tailings facilities constructed in nearby drainages. Infiltrating rainwater with a typical pH of about 5.6 is an additional component introduced into the spent ore after disposal. Methods Field sample collection. Spent ore samples were collected from conveyor belts (or other convenient points) at heap-leach mines by personnel from the South Dakota Department of Environment and Natural Resources. The samples were placed in black plastic bags that were contained within 5-gal buckets and sealed to prevent exposure to ultraviolet light. The samples had a minimum head space to limit evaporation and contact

Jan 1, 1997

By Richard Hogg, Heechan Cho

Investigations of long-time grinding of fine quartz (to about 80% passing 0.35 pm) in a 0.6 liter stirred-media mill are described. Breakage rates and primary breakage distributions have been determined based on extensive characterization of the ground products by laser scattering/diffraction and gas adsorption. The results indicate that, while there is qualitative similarity between the breakage parameters for ultrafine and conventional (coarse) grinding, there are important, quantitative differences. In particular, it is found that primary breakage distributions become significantly narrower in the submicron sizes. The trend can be described using double-truncated log-normal distributions in which both a maximum (breaking) size and a grind limit are specified. The breakage distributions become progressively narrower as the size being broken becomes finer. Breakage rates follow a typical, consistent pattern in which the rate decreases with size according to a simple power law. Further decrease in the rates seems to occur after very long grinding times when the entire mill contents become finer than about 1µm. The effect is explained as a result of changes in the rate/size relationship in the submicron range.

Jan 1, 1995

By w. Chruscielewski, T. Domanski

INTRODUCTION Concentration of radon 222Rn and its decay products occuring in the Polish mines of metal-ores call for the necessity of systematic radiation control /Do8la/ both of the working environment and of the miners' personal exposure. The attempts at introducing a system of radiological protection in mines, similar to the ones existing in X-ray or isotope laboratories, took several years and consisted of development of the methods for control of concentration of radon and its progeny in the air, as well as the methods for measuring individual exposure. It was accepted that the assessment of both transient concentration in the air and of personal exposure are basic elements of the control system, which should be implemented independently of each other. Concentration measurement serves to detect and to determine those areas in mines where there is intensive radon emanation, and where current control of the effectiveness of technology introduced to deacrease the concentrations is necessary; personal dosimetry results in the assessment of the actual exposure of miners to radiation. PRINCIPLES OF THE SYSTEM The assessment of working environment is based on concentration measurements of the potential radiation energy of radon alpha decay products. Decentralized assessment is carried out by the special dosimetric service operating in each mine. Dosimetrists are equipped with portable radiometers, type RGR-11, made by the institute of Nuclear Research, Warsaw. The radiometer is presented in Fig. 1. Measurement of filter activity is performed automatically according to Markov's method /Ma62/ or any other method. Simultaneously to potential energy measurement the dosimetrists are measuring the dust concentration in the air and ventilation rate. Ventilation service looks for correlation between those indices and the concentration of radon daughters in the air. Derived Air Concentration /DAC/ for concentration assessment was accepted to be 6.25 10-6 Jm-3 /0.3 WL/ according to ICRP recommendation /Publication No. 24/ /ICRP77/. If environmental measurements reveal potential energy concentration exceeding the value of 0.3 DAC at working places, the miners employed there are subject to individual control of personal exposure. Individual exposure measurement is carried out centrally by the Institute of Occupational Medicine in [Lodz] for all metal-ore mines. Miners who are to be included in the control scheme are referred by a mine management to the Institute where they are registered and assigned a dosimeter. A passive dosimeter with

Jan 1, 1981

By Guillermo Chong Díaz

A brief overview of industrial mineral exploration and exploitation in Chile is given. World class deposits of salt, lithium, nitrate, and iodine are present in northern Chile. The potential for further exploration and exploitation of these deposits, as well as the substantial reserves of other mineral commodities such as gypsum, anhydrite, volcanic rocks, and borates are discussed. In conclusion, industrial minerals mining in Chile has considerable potential, particularly as joint ventures between foreign and domestic companies. This has been demonstrated in the extraction of nitrates, lithium, iodine, and diatomites. However, as outlined in this paper, a number of factors need to be overcome before the true potential of the Chilean industrial minerals industry can be realized.

Jan 1, 2001

By Mark E. Smith

Large scale copper heap leaching in Chile began in November 1980 when the Lo Aguirre heap leach project was put into operation. At almost the same time, El Indio gold mine began production. While El Indio was not a heap leach project, it was Chile's first major bulk tonnage, open-pit gold deposit. This paved the way for the introduction of North American gold heap leach technology in the early 1980s. Heap leaching has become more popular in Chile during the past five years because it allows the exploitation of large but relatively low grade ore bodies at a reasonable cost. Pioneering research in hydrometallurgy carried out at some Chilean universities and at the Centro de Investigaciones Minero Metalurgicas (CIMM) played an important role. There are more than 10 large copper heap leach and solvent extraction/ electrowinning (SX/EW) process plants in different stages of development in Chile. Total production from these facilities will eventually increase Chile's present copper exports about 50%.

Jan 1, 1995

By G. T. Adel

The flotation behavior of a -28 mesh Pittsburgh No. 8 coal sample is investigated through the use of Scanning Electron Microscopy in conjunction with Image Analysis. Release analysis is used to generate the flotation products, which are then characterized to provide the particulate composition in terms of pyrite, mineral matter and carbonaceous material. The results of this investigation indicate that the material recovered in the first stage of release analysis tends to be well-liberated carbonaceous material. This is followed by an increase in the recovery of middlings and fines in the later stages of the process. Any free carbonaceous material remaining in the tailings from the release analysis test tends to be associated with the very fine sizes (-400 mesh). Pyrite recovery is attributed to the hydrophobicity provided by small inclusions of carbonaceous material, since the amount of truly liberated pyrite particles (i.e., 100% pyrite) present in the sample is found to be negligible.

Jan 1, 1994

By Rodrigo Jerez

The mining business in general, and coal mining in particular, is exposed to frequent and significant swings in the business cycle. Marginal coal production enters the market place in a nearly perfect competition. It must be priced aggressively if market share is to be gained. The minimum price acceptable from the standpoint of the producer is reached at the point where total variable cost are recovered. Competition occurs as companies move to reduce their variable costs in an effort to cover some portion of their fixed costs at reduced market prices. Production planning and scheduling plays a critical role in reducing costs. Multiple scenarios based on changing market conditions require that competing firms have tools available to evaluate the economic impact of transportation, blending, and processing options. In certain applications, significant cost savings can occur as a result of blending or altering preparation levels. Linear programming provides a tool with which to evaluate options and acts as a like between the mine plan and marketing decisions.

Jan 1, 1992

Cement in 1975 indeed did operate in an unfriendly environment. World recession, escalating costs, fuel crises, reduced product demand . . . . all led to market conditions detrimental to industry profit margins and investment re turns. During the year plant utilizations fell, break-even points were raised, and competitive moves introduced to move built up inventory levels. A number of cement plants were temporarily taken out of production to help alleviate specific situations. Meanwhile, under resultant financial pressure, several companies omitted dividend payments, changed their top executives, and reorganized and reduced staff overheads. It was a difficult year for cement, yet a much more ominous note was sounded in permanent plant closings. Four more cement operations were shut down in 1975; to date in 1976 we know for sure of three additional plant closings, while rumour has it that at least one more may not be in production by year-end. The somber feature is found within the descriptions of the closed facilities, and in the stated reasons for their being taken out of cement manufacture.

Jan 1, 1976

By J. O. Marsden

The 1980s saw a revolution in gold extraction technology, paralleled only by the implementation of the cyanide leaching process in the late 1800s. This revolution was led by the widespread adoption of carbon adsorption processes for gold recovery, heap leaching of low-grade ores and development of a variety of oxidation processes to treat refractory ores. In the late 1980s, gold production in almost all regions of the world increased, with the notable exception of South Africa. This geographical variety is creating a greater diversity of challenges for gold metallurgists. This is due to a wider range of ore types, new and varied environmental regulations and legislation, and a requirement to select the most appropriate technology to suit local needs. North America has led this technological revolution in the gold industry and is responsible for commercialization of most of the major innovations: carbon-in-pulp, heap leaching, whole ore pressure oxidation and whole ore roasting. Process selection trends A general trend in precious metals extraction technology has been the treatment of ores with progressively lower grades. The lowest cost treatment, dump leaching of material at run-of-mine size, has been increasingly applied. ZortmanLandusky, in Montana, is successfully leaching material above a cutoff grade of 0.2 g/t (0.006 oz/st) at an average rate of about 28 kt/d (31,000 stpd). At this scale of operation and in the absence of any cyanide-consuming species in the ore, process operating costs for a ge¬neric run-of-mine leaching operation are estimated to be between 60 and 75 cents/ t (66 and 77 cents/st). One of the largest heap leach opera¬tions treating crushed ore is the Round Mountain Mine in Nevada. It processes about 45 kt/d (49,000 stpd) at an average grade of 1.1 g/t (0.032 oz/st) at a nomi¬nal crush size of 80% -19 mm (-0.7 in.). Round Mountain also treats lower grade ore above a 0.2 g/t (0.006 oz/st) cutoff by dump leaching at run-of-mine size.

Jan 1, 1993