Search Documents

By J. F. Lupo

There are numerous mines throughout the world that have open pit highwalls developed partially or wholly in soil or soil-like materials. Soil-like materials are considered to include soils (either transported or residual) and highly weathered rock, which may have soil-like behavior. These materials generally have characteristics or material properties that vary considerably from those of moderately weathered or fresh rock. Given these differences, it is important to consider the characteristics of soil-like materials to design safe open pit slopes. In the design of open pit slopes in soil-like materials, it is important to recognize the behavior of these materials is strongly dependent upon their mineralogy, degree of weathering, cementation, stress history, depositional history, and presence of water. As a result, soil-like materials may contain one or more of the following characteristics that can have a significant effect slope stability and design: - Relict structural features (joints, faults, etc), - Sensitivity to moisture (both wetting and drying), - Zones of alteration with variable strength and drainage characteristics, - Zones of low permeability creating perched ground water conditions, and - Undrained and drained strain softening or strain hardening behavior.

Jan 1, 2011

By W. Porter Place

The Trolleyphone was the first successful application of carrier current techniques to a DC power distribution system to provide voice communication between fixed points and moving locomotives and traveling cranes, This was a significant breakthrough because this not only in itself provided a useful new tool for industry, but the knowledge gained in the transmission of voice communication is paving the way for many other things, chiefly, remote control and indication systems which promise to have a far reaching effect during the upcoming age of automation. Once it has been established that we can communicate between men who operate machines, the next step will be to operate the machines themselves.

Jan 1, 1958

By Joseph F. Shirley

A froth flotation plant to recover by-product molybdenite must be designed specifically for the selected separation process and the type of ore being treated. However, some general rules concerning by-product molybdenite plant design can be suggested that would be valid for most processes. The term by-product molybdenite in this paper is limited to the recovery of molybdenite from copper porphyry ores, which essentially amounts to selectively separating molybdenite from copper and iron sulfide concentrates. In addition, most of the discussions would apply only to the almost universally used approach of floating the molybdenite and depressing the copper and iron sulfide minerals.

Jan 1, 1979

By A. Moergeli

The Swiss are building the world’s longest tunnel, the 57-Kilometer (35-mile) long Gotthard Base Tunnel. Lot 252, Tunnel Amsteg: Two Hard Rock Tunnel Boring Machines (TBM) crossed hydro-thermally decomposed granite. While the East TBM advanced slowly but steadily, the West one got stuck for five months and had to be recovered by special means and methods. Both TBMs have finished their more than 11-Kilometer (7 miles) long drives successfully. Lot 360, Tunnel Sedrun: For the first time in tunneling, roadway support machines are used through most challenging, squeezing geology. They constantly advance in full face mode for about one Tunnelmeter/24 hours.

Jan 1, 2007

By Robert C. Ellman

Lignite and subbituminous coals are utilized essentially as mined without beneficiation. Most of the present production is used to generate electric power and the major problem in this use is ash deposition on fireside surfaces. The preparation at existing mines involves principally crushing and screening operations. Blending of production from different locations within the mine is practiced in several mines to control ash composition. Drying and oil treatment for freezeproofing, of lignite are used to a limited extent during winter. Future processing may involve both washing and drying operations to alter ash composition by ion exchange and upgrade the low-rank fuels to higher heating values. Research has been initiated to determine the feasibility of such processing.

Jan 1, 1969

By P. R. A. Andrews, G. Heinrlch, V. I. Lakshmanan

The paper describes a simplified method to chemically modify the surface of industrial mineral fillers. Four industrial mineral samples were taken from feedstock of commercial fine grinding operations. These samples were ground in bench scale ball mills and in the presence of various organic solvents. The ground products were measured for particle size distribution, surface area, surface chemistry by oil absorption and degree of organicJminera1 bonding. Where appropriate, the ground products were compared to commercially available surface modified, industrial mineral fillers.

Jan 1, 1990

By Dennis L. Boley, Francesco Gallavresi, Donald A. Bruce

The authors describe novel aspects of ground reinforcement and treatment as related to soft ground excavation for tunnels throughout the world. Insitu reinforcement for cut slopes (soil nailing), as underpinning (reticulated micropiles), and as direct tunnel support (infilaggi) is introduced. Ground treatment focuses on new aspects of permeation grouting (by the tube'a manchette system), and on jet grouting-a very powerful and positive new technique. Recent developments in equipment, materials, methods and instrumentation are reviewed, with special reference to major tunnelling projects in Italy and Singapore.

Jan 1, 1987

By Liyan Ren, Huayang Dai, Yingcheng Li, Enquan Wang

"Three-dimensional geological modelling of coal mines is critical to the sustainable development of the mining industry. On the basis of comprehensively analyzing 3D geological modelling methods, according to the available data of mine such as geological terrain maps, cross-sections and boreholes, we present a 3D modelling method by integrating ArcGIS and 3D GeoModeller. Our motivation is to integrate the advantages of both software modules in processing, converting, integrating and transferring geological information. Special attention has been given to the data structure and processing flow. We build a 3D geological model of the Xieqiao coal mine and successfully extract the geological framework of the strata in the 11118 workface, which is consistent with that of the actual explored geology.Introduction/Background Pertinent impediments such as a lower information degree, the out-of-date information infrastructure and the low level of information management and decision-making make it critical for there to be improvements in mines. Modern exploration technologies favour the construction of digital mine. Digital mine promotes the transformation of the mining industry by integrating information, automation and intelligence to build safe, efficient, high-yield, green and sustainable mines. Three-dimensional geological modelling and visualization of mines are at the core of digital mine. Compared with traditional 2D geological data, 3D models express the various geological phenomena completely, as well as reproduce the spatial distribution of geological units quickly, allowing for the prediction of mining subsidence, better decision-making and improved geological analysis. Modelling methods such as multi-DEM, tetrahedral grid and the generalized tri-prism that are based on borehole estimation and interpolation data are used to construct 3D models of mine geology (Chen 1995,Wang et al 2003, Wu 2004a); nevertheless, these methods cannot fully use multi-source mining data, whereas multi-source integration methods can be used to build 3D models (Kaufmann and Martin 2008, Zhao et al 2009) but require user interaction in model construction and low automation in model updates. During coal production, a plethora of geological data is accumulated. The organisation of discreteinformation under dynamic conditions and the extraction of meaningful information to better service for three-dimensional modelling is a meaningful work (Wu et al 2004b)."

Jan 1, 2017

By Y. C. Kim

Three rock fracture parameters define three points along empirical cumulative size (of rock fragments) distribution curves at Inspiration copper mine. These parameters are: rock quality designation (RQD), longest piece of intact rock and % of +1 inch. The RQD and the longest piece are actually measured on drill hole cores whereas % of +1 inch is visually estimated on the same cores. These size distribution curves are then utilized in a variety of engineering applications such as; slope instability analysis, blast design, copper recovery prediction from heap leaching, etc. The three rock fracture parameters for two dominant rock types (porphyry and schist) in the pit had to be estimated separately due to different rock fracture characteristics.' Both ordinary kriging (OK) with measured hard data only and soft kriging (SFTK) with hard and soft data were used to estimate each parameter. The cross validation of 100 measured sample values served as the-basis for evaluating the potential benefits of SFTK over OK. Use of subjective information during SFTK required obtaining (prior) probability distributions for all three rock fracture parameters. These distributions were obtained from the typical rock fracture parameters observed in drill hole cores falling inside the geologically interpreted structural domains with varying degrees. of fracture intensity and also through direct mapping along the exposed bench faces. Two different types of soft information were developed for this study; namely, Type "A" and Type "K". The former is based on sample distribution of fracture parameters whereas the latter is based on two step estimation designed to narrow the range of variation observed in data Type "A". The results of the cross validation were analyzed using a linear regression of actual values versus estimated values. The results confirm an improvement on the estimates made by SFTK with hard and. both types of soft data over those produced by OK with hard data only.

Jan 1, 1989

By B. K. Gupta

Arch Mineral's Captain Mine has used the Bucket Wheel Excavator System(BWE) for over 3 years in conjunction with a 180 yd3 (138M3) stripping shovel. The bucket wheels prestrip the soft overburden ahead of the shovel. This soft overburden is brought to the spoil side through a series of shiftable conveyors and placed by a spreader over the ungraded or partially graded shovel spoils. The placement of the soft overburden and top soil is accomplished in a manner that meets the reclamation mandates. The prestripping by the BWE has reduced the incidence of the highwall and spoil slides, depth the stripping shovel has to dig and the volume handled by the pullback draglines.

Jan 1, 1984

By T. Shungu, N. Vermaut

The various copper-cobalt ores mined by Gecamines, together with typical plant applications and results, are briefly described. Intensive laboratory investigations have been undertaken in recent years to improve the metallurgical performances of the various concentrators. As a result of these tests, it was shown that the flotation of the siliceous oxide ores could be improved by increasing the efficiency of the palm oil collector (energetic conditioning, chemical emulsifier, petroleum sulfonate addition) and by varying the froth depth in the cells. A new flowsheet incorporating these modifications and a regrinding stage has been approved for the rehabilitation of the Kolwezi concentrator. For what affects dolomitic oxide ores, hydroxamates were tested as secondary collectors and, based on successful laboratory results, plant trials were run but failed due to excessive frothing. In other plant tests, xanthates were replaced by a xanthate- fatty acid mixture; plant trials over more than one year proved successful for copper, but not for cobalt. Mercaptans were tested as secondary collectors for the sulfides flotation from sulfide or mixed oxide-sulfide ores; laboratory results proved successful but, to date, no plant test has been run.

Jan 1, 1987

By Glenn M. Boyce, Timothy R. Coss

Microtunneling first appeared with some regularity in the United States in 1987. Until then, only Japan and Germany utilized this method of construction. Its high costs initially limited its application to special situations. The last ten years have seen the use of new pipe materials, new machines, new cutterheads, new techniques, and an average growth of30 percent each year. This paper documents the growth and changes that have occurred with microtunneling. Based on current industry practices and advances from abroad, this paper postulates what the next ten years may hold.

Jan 1, 1997

By D. R. Taylor, R. G. Goss

The use of clay granules as carriers for pesticides dates from the early 1940's and by the present day represents a business conservatively estimated at between 200 - 300 thousand tons / year in the U.S. alone. Aside from economic and specific target pest efficacy advantages, the use of clay granules as pesticide carriers also delivers a number of environmental benefits which will be reviewed. Topics to be discussed will include: 1) drift control (versus liquid sprays), 2) mobility (in the environment), 3) worker safety, and 4) transportation (spill) safety.

Jan 1, 1999

By T. C. Rao, D. D. Patil

The fishhook effect, wherein the recovery of fine particles in the underflow increases with decreasing particle size, has been observed in hydrocyclone classification. A systematic study was carried out to determine the factors affecting the recovery of very fine particles to the underflow. Attempts were made to identify factors, i.e., design and operating variables, that affect the size at which this phenomenon occurs. Experimental results show that the sizes at which the fishhook effect occurs is mainly a function of feed size distribution and solids concentration and is less dependent on the design variables.

Jan 1, 2002

By S. K. Kawatra, T. C. Eisele

Under normal conditions, a significant amount of pyrite is recovered in the froth during flotation of high-sulfur coal. To reduce this pyrite recovery, it is first necessary to determine the primary recovery mechanism, because different measures are required for reducing entrainment, locked particle flotation or true hydrophobic flotation. In this paper, evidence is presented that suggests that hydrophobic flotation is not the major mechanism for recovery of liberated pyrite; instead, the bulk of the recovered pyrite results either from simple entrainment or from being physically locked with floatable coal particles.

Jan 1, 1993

By J. Brinen, D. R. Nagaraj

Secondary Ion Mass Spectroscopy (SIMS) was used to study copper ion adsorption, and its effect on subsequent sulfide collector adsorption, on pyrite and pyroxene minerals under flotation related conditions. Copper was found to adsorb on both of these minerals and cause enhanced sulfide collector adsorption. The distribution and depth profile of copper and collector on these mineral surfaces were obtained by using SIMS in the imaging mode. The results of this study have provided a valuable insight to understanding pyrite and gangue flotation observed frequently in operating plants.

Jan 1, 1995

By J. A. Finch

The use of pneumatic methods for measuring interface level in flotation columns is analysed. It is shown that errors can vary over a wide range (e.g. 40 cm. in one industrial application) depending on bubble size, particle size, bubble loading, liquid hold-up and bulk slurry density. Accurate measurements (+ 5 cm) can be obtained by measuring intensive properties of the froth near the interface. Methods based on the measurement of temperature and conductivity are described and analysed. Control of the interface level using these measurements subject to various disturbances is demonstrated.

Jan 1, 1988

By I. H. Douglas

All grade control methods in use currently by the mining industry are imprecise. The methods suffer from being locally inaccurate, leading to are loss and contact dilution. An ore/waste indicator variable can be used to predict the probability of ore occurrence at a given location, Po. Then, an ore grade Zo for an ore location and a waste grade Zw for a waste location are obtained. The expected revenue is calculated at each location, based on its probability of being are or waste, the corresponding grade, and on the cost of mining and processing the ore or the waste. Finally, the decision of whether to recover the block is based on the expected revenue value for that block. The method is illustrated with an example taken from the Jerritt Canyon district in northeastern Nevada.

Jan 1, 1994

By R. D. Peterson

Autocad has become the standard graphics package for the mining industry as well as the general engineering profession. This paper discusses the evolution that mine planning has undergone and the trend toward compatibility with Autocad. It discusses the common use of Autocad in mine planning and systems modeling using a program called ICAMPS developed by Ohio Automation. As an example of its usefulness the use of the interactive ventilation network modeling capabilities are discussed specifically and are applied to mine planning at an operating trona mine. The ventilation analysis feature of the ICAMPS software works from Autocad drawing of the as-mined map and the projected mine layout. Using on-screen displays of these maps and the snap-on feature of Autocad, the planner designates nodes in the ventilation network, connects them into branches and selects branch characteristics from a side bar menu. The color coded ventilation network appears with the branch parameters alongside each branch. The software calculates the length of airways, computes the branch resistances where needed, converts the input into the required format and passes this information as input data along to the PENNVEN simulation program written by the Pennsylvania state University. Output is available in graphical as well as report format. The color coded graphs include pressures at the nodes and flow quantities on the branches. Since the networks come from the mine maps, the ventilation schematic displays are to scale and can be plotted separately or superimposed on the mine maps.

Jan 1, 1995

By K. W. Grubaugh

Indigenous people are nearly always affected when projects enter their territory. Crop and other asset compensation can help or undermine a project’s progress depending on the approach. When compensation is handled poorly, a technically viable project can get indefinitely entangled by local unrest. Stake holders associated with compensation issues include; the state, the indigenous people, non-governmental organizations, and the developer. Appreciation for the unique perspective of indigenous peoples and the influences affecting them can avert problems and prevent delays. A review of the compensation issues encountered in Ghana during its recent gold boom can assist in avoiding problems associated with handling poor and uneducated people.

Jan 1, 2002