Search Documents

By J. Siege1, R. S. Popielak

A computer model was used to simulate the effect of leakage through confining beds on a hypothetical in situ leach operation in an aquifer with a thin mineralized section. The simulations were used to assess economic and potential environmental implications of leakage on an in situ leach operation. Four scenarios were modeled - three representing cases with different degrees of confinement, and the fourth representing a stratified ore zone under a low degree of confinement. The model simulated the travel path and travel time of lixiviant given the hydraulic conditions prescribed in each scenario. The results show that the travel path and travel times vary by about 10% for confinement ranging from nearly impermeable (essentially no leakage) to an extremely low level (thin confinement with a permeability about equal to that of the aquifer) for isotropic aquifer conditions. The aquifer thickness contacted by the lixiviant varied from 85% to 90%. Horizontally, 55% to 60% of the aquifer was contacted. The flow paths in the stratified aquifer were reduced in the vertical direction and expanded horizontally. Forty- five percent of the aquifer thickness was contacted vertically with 88% contacted horizontally. Break- through time for lixiviant traveling at mid-depth of the aquifer increased two times when the leakage was increased from nearly zero to a value representative of thin and highly permeable confinement. Leakage affects the economics of in situ mining by (1) increasing the time required to leach out the ore, and (2) increasing the thickness of the ore zone aquifer to be restored. The potential for environmental impacts appears to be minor. In all four simulations, the lixiviant did not contact the confining strata. Restoration would be limited to cleanup of the ore zone aquifer within the thickness contacted by lixiviant and within the radius of the lixiviant that traveled farthest away from the production cell.

Jan 1, 1988

By Yong Pan, SRIVATSAN JAYARAMAN SRIDHARAN, Purushotham Tukkaraja

The block cave mining method poses unique ventilation challenges compared to other underground metal mining methods. This research study focuses on assessing the airflow behavior in regulated airflow distribution systems by developing a 1:100 scaled block cave experimental model and a numerical model. This study also investigated gas flow behavior under various airflow conditions. Based on our findings, we observed that reduction in particle size and porosity of caved materials, decrease in cave footprint, and closure of undercut drifts would increase cave airflow resistance. The increased airflow is found to be beneficial for gas dilution regardless of its source locations, while the regulated airflow distribution system might deteriorate the gas dilution situation when the source is located in the extraction drifts.

Sep 1, 2022

By K. L. Whitehead, R. A. Jankowski, N. I. Jayaraman

Most continuous miner sections utilizing flooded-bed scrubbers also use blowing face ventilation. Blowing ventilation, however, interferes with dust capture and minimizes scrubber effectiveness. To enhance the efficiency of the scrubber system and reduce dust concentrations, the Bureau of Mines tested various combinations of operating parameters. Experiments for system efficiency took place in a full- scale model mine at 3.05 m roof height. In general, higher values for scrubber and face airflows resulted in lower dust concentrations. In addition, optimum dust controls would include a face ventilation to scrubber airflow ratio of one. When the airflow ratio was either less than or greater than one, the dust levels in the return and at the operator locations increased. No single dust control technique was the most effective one at all locations due to mutual interaction among techniques.

Jan 1, 1992

By D. M. Cregger, J. L. Rosenblad, R. E. Ranken

The construction of a large span, high-walled underground opening in a low strength shale rock is unprecedented. The feasibility of constructing a pumped storage project with several tunnels and a large underground powerhouse in low strength shale rested largely on the feasibility of building stable openings large enough to accommodate the required equipment. Because of the lack of experience with large openings in shale, the decision was made to excavate a test adit and test chamber and conduct a multi-faceted geotechnical evaluation program designed to yield pertinent in-situ data on the ability of the shale to accommodate a large underground opening. Factors considered in the shape, size, orientation, and location of the test chamber were: (1) similarity to the anticipated powerhouse chamber, (2) nature of the most important data to be obtained, (3) feasibility of construction, and (4) economics.

Jan 1, 1983

By Milton E. Wadsworth

Cost effectiveness in gold and silver leaching has centered mainly on reducing or preventing excessive use of lixiviants. In cyanide leaching practice, the active reactants, cyanide and oxygen, present different problems. The activity of cyanide may be adjusted at cost, but oxygen from air, has a fixed, low activity with an equilibrium concentration of ~7 ppm. Consequently, the use of air in agitation and heap leaching presents distinct kinetic problems. The refractory ores are either high consumers of oxygen or tend to immobilize dissolved precious metal-cyanide complexes. Commercial treatment of refractory ores involves oxidation by pressure leaching, roasting or biooxidation prior to cyanide leaching. Chemical reactions important in preoxidation of refractory sulfide ores by pressure leaching and biooxidation are considered. Major emphasis is given to the role of oxygen in heap leaching of oxidized ores.

Jan 1, 1995

By Mark J. Schultz, William J. Francart, Michael P. Snyder

The Pittsburgh Safety and Health Technology Center surveyed MSHA Coal Mine Safety and Health Districts to monitor the implementation of computer based atmospheric monitoring systems (AMS) in underground coal mines. This survey was first completed in 1984, and has been periodically updated with the latest update completed in 1995. The utilization of computer based monitoring systems has steadily increased over the past 12 years, with over 16 percent of all producing underground coal mines using this technology in 1995. This paper discusses the results of the MSHA 1995 AMS Survey.

Jan 1, 1997

By William J. Francart

In 2003, MSHA initiated a survey of the 11 Coal Mine Safety and Health Districts to develop a database for the implementation of Atmospheric Monitoring Systems (AMS) in underground coal mines. Mine operators continue to realize the benefits of improved fire detection capabilities, as the number of mines using the systems, as well as the percentage of mines, continues to increase. Fire detection data and new technology implemented in underground coal mines is discussed as well as regulatory compliance, diesel exhaust considerations and hydrogen interference in carbon monoxide detection.

Jan 1, 2005

Recent accelerated exploration efforts in southwest China have progressively quantified the vast phosphate resources in the Yunnan Province. To date, according to Chinese geologists, potential reserves in the province may be on the order of 4 Gt, which would equal the entire US reserve base. Development of this vast reserve is underway at two sites located 60-70 km southwest of Kunming, the provincial capital of Yunnan. The first, the Kunyang open-pit phosphate mine, produces an estimated 1.5 Mt/a of 22-30% P20,5. The other project located north of Kunyang is the Haikou mine, which the Chinese consider a possible 2.0-Mt/a operation. Because average ore grades run 3% less than those of Kunyang, beneficiation will be necessary. While the latter project has been initiated on a small scale, it is basically still on the drawing board. Brown and Root and the US Bureau of Mines are assisting on the project. Both operations are under the direction a regional administration which reports to the Ministry of Chemical Industries in Beijing. Combined production from both mines could represent some 70% of China's future productive capacity. Ore reserves in the region are estimated at 400 Mt by local officials. Geology of the District The phosphates are considered Cambrian in age and rest on a Precambrian dolomite. The Indian Ocean, Chinese geologists say, may have been the original source. The line of deposition stretches on a trend from Vietnam in the southwest, through Yunnan, into Sichuan Province to the northeast. Because the area is considered very stable from a geologic viewpoint, large quantities of phosphate have been deposited and large outcrops are known to occur everywhere in the province, according to Chinese sources. The Kunyang and Haikou ore bodies are thought to be two wings of an anticline with the former the southern portion, and the latter the northern portion. Each ore body strikes on an east-west axis. While there are many localized phosphate operations throughout the province, the Kunyang mine is the premium producer. Kunyang's Mining Development The Kunyang open-pit mine was opened in 1966. During the early years, operations were considered somewhat disorganized. Systematic mine planning and normal operations were not initiated until just two years ago, according to mine management. In 1979, Kunyang finally reached its design capacity of 1.5 Mt/a. The ore body consists of two phosphate beds separated by a band of shale. The top layer of phosphate varies from 4 to 8 m, averaging 6 m. The middle shale layer is 2 in. The third layer, which is not as rich as the top, is approximately 4 m. To further complicate matters, the ore dips 15° to the south over a strike length that is currently undefined, but believed to be

Jan 3, 1980

By Anders Sellgren, K. Hansson, A. Jedborn

In the mining industry, conversion of fine particles into a slurry is often part of the normal processing of the ore. Therefore. from a system's point of view, slurry transportation would be considered as a natural alternative, all the way from the working face to the final processing. In underground mines, there is sometimes a considerable inflow of ground water that has to be pumped out. When the mine dewatering installations are integrated with a hydraulic hoisting system, the cost of power needed to pump out the ground water can be excluded from the cost of hoisting, compared with other modes of transporting the solids to the surface. The chief advantage of hydraulic hoisting is that the hoisting capacity can be increased at comparatively low total cost without necessitating the sinking of new shafts. Alternative examples include deepening of the existing mechanical hoisting system, truck, or conveyor belts transport in ramps to the present level. These often become very expensive. The economic effectiveness of hydraulic hoisting and hydraulic design considerations have been discussed by Kostuik (1965) and Sellgren (1985, 1986) for both small shallow mines and large deep underground mines. Objective and scope The objective of this study was to demonstrate the feasibiliy of hydraulic hoisting in hypothetical examples of mine deepening. Underground grinding to a maximum particle size of about 700 um (about 25 mesh) is considered. The pumping of ground ore products with positive displacement plunger or membrane type of pumps at working pressures of up to 15 MPa (2200 psi) is a thoroughly tested technique (Venton, 1986). Hydraulic hoisting system A hydraulic hoisting system is described schematically in Fig. 1. The ore is mined, handled, and crushed conventionally. It is then ground wet underground. The slurry is then temporarily stored in an agitated tank and pumped to an agitated receiving tank on the surface. The ore is then further processed in the concentrator. The capacity of a pipeline is very high. For example, an annual production of 500 Kt (550,000 st) of ore can be handled in a 100-mm-diam (4-in.-diam) pipeline. Systems layout - economic effectiveness Schematic mine layouts are presented that represent situations where hydraulic hoisting often is the most economical alternative. A situation where the ore is trucked to the level of the existing hoisting system is shown in Fig. 2 (following page). With hydraulic hoisting, only a shaft for ventilation, pipe- line, and personnel are needed. In a first phase (Fig. 2). a hydraulic hoisting installation with crushing and grinding units, storage facilities, and pumps has been located at a level of about 400 to 600 m (1310 to 1970 ft) below the surface. With further development of the mine, the hydraulic hoisting

Jan 1, 1990

By Peter N. Calder

There is little doubt that the stability of both highwalls and spoil piles is essential to efficient strip mining. Accurate determination of the appropriate geotechnical parameters will pay dividends during mining, but only if the mine operation closely follows the engineering plans which have incorporated These factors. Productivity is invariably higher in mines where failure of highwalls and spoil piles does not occur. This is the result of the reduced rehandle and better working conditions found in stable mines. Control of the waste piles and highwalls also leads to better coal recover since failures can result in the burial of uncovered coal, which is then lost to mining. Safety is an important consideration. The importance of providing a safe working place for employees and of protecting costly mining equipment is hard to overemphasize. For miners, working in areas where instability exists, the degree of hazard involved in their occupation is increased particularly where night operations are involved. It is true, too, that there have been many cases where loading equipment has been buried and severely damaged by failures.

Jan 1, 1980

By Bengt L. Stillborg

INTRODUCTION This paper summarizes the result of a two and a half year research program. The objective of the research was to develop a fundamental understanding of the Rib-in-Roc method. Through the development of a new model technology, namely three-dimensional physical models which powerfully exploit the results of dimensional analysis Stillborg, Stephansson and Swan (1), it has been possible to establish the contribution to both permanent and immediate stabilization of a large underground opening pre-reinforced by the Rib-in-Roc method. Using the results from these physical models and earlier work by Stillborg and Stephansson (2) and Åkesson (3), a conceptual synthesis is given in this paper so demonstrating the Rib-in-Roc method to be a practical working system of pre-reinforcement. DESCRIPTION OF THE RIB-IN-ROC METHOD To give the reader an idea of how this method of pre-reinforcement is performed, a short description will be given, Figure 1. Before any full-scale excavation takes place an entry is made in the host rock and rib raises are driven around the proposed opening. These raises are made at a spacing that is dependent upon rock quality; an opening in poor rock needs more ribs per length of opening. As the ribs are driven they are used as a site from which very competent rock bolting can be done. As a rib is excavated it is filled with reinforced concrete. Finally after having in this way reinforced the zone around the proposed opening, (a reinforced arch is formed) the displacements are automatically controlled as the opening is being excavated. Using this method openings with a span of 50-60 meters (160-200 ft) and a height of 60-80 meters (200-260 ft) are likely to be realised.

Jan 1, 1979

By K. E. Lasaridi

Increasing soil organic matter was considered to be an important factor for the establishment of vegetative cover in abandoned quarries of perlite and bentonite in the island of Milos. For this reason, the feasibility of composting local organic wastes and by-products for use as a soil amendment was examined in this study. A mixture of organic wastes of vegetative origin and seaweed, in proportions that correspond to local material availability, was composted in laboratory scale reactors and the composting progress and compost quality were evaluated. Temperature, airflow and respiration rate were continuously monitored and various compost quality parameters, such as C/N ratio, nitrate nitrogen and seed germination were analysed. Addition of inorganic nitrogen was necessary for the biodegradation of the substrate, while the main problem for the compost utilisation was related to its high electrical conductivity, characteristic of seaweed containing mixtures, which further increased with nitrogen addition.

Jan 1, 2002

By Rodger E. Denison

The Middle Ordovician Simpson Group in the Arbuckle Mountains of southern Oklahoma contains sandstones of unusual purity. These have been exploited as glass sands since 1913 (Ham, 1945). Where quarried, the sandstones are uncemented or weakly cemented, greatly facilitating mining and processing. The origin: sedimentary setting, and lack of cementation of these valuable sands has been the source of much discussion. The lowest of the sandstone units in the Simpson is at the base of the Oil Creek Formation. The basal Oil Creek sandstone is exposed in a series of accessible quarries north of the town of Mill Creek in Johnston County. Virtually all conclusions and generalizations concerning origin of the Simpson sandstones are based upon observations made in these quarries. The three Simpson sandstones overlying the Oil Creek share many of the same distinctive qualities, and there is an assumption that they share a common origin.

Jan 1, 1999

By J. Kemeny, K. Girdner, M. A. Lowery

A strategy for proactive blast planning to improve the postblast fragmentation size has been implemented at the Phelps Dodge Morenci Mine. This strategy was developed in specific phases that include stabilization of blasting practices, systematic changes in blast design and quantification of the size distribution of blasts. Implementing this new strategy would not be possible without an accurate method for quantifying the postblast fragment size distribution. The Split image processing system is now being used to assess fragmentation size using muck pile digital imaging taken on a daily basis and an online fragmentation analysis system installed at the primary crushers. Drilling and blasting variables and fragmentation size are entered into a database, spatially evaluated in a geographic information system and subsequently utilized for mine planning purposes. Using this strategy, significant improvements have been made in postblast fragmentation and continued improvements are expected in the next several years.

Jan 1, 2002

By Earl M. Frizzell, Ronald W. Utley

Introduction For the past several years the Bureau of Mines has undertaken research to develop alternative mine material haulage systems that will improve mine productivity, reduce haulage costs, increase mineral availability, and conserve energy. One basic concept being pursued is a means for crushing primary blasted rock to a size that can be reliably and economically moved on conveyors. During 1980, mine requirements for this equipment and the capability of existing technology to satisfy these requirements were assessed. The study continued into 1981 on the basis that satisfactory equipment for this purpose needed to be developed. The objective of the 1981 program was to perform an engineering design of such a system. A mine survey and equipment development study was conducted in cooperation with the open-pit mining industry by GATX through its subsidiaries, Fuller Co. (a crusher manufacturer) and GARD Inc. (GATX's research and development center), under contract to the USBM. Results of a mine survey in the copper, iron, and molybdenum industries indicated that a universal crusher system could be developed even though details might vary from mine to mine. The crushing characteristics, including tonnages desired, were similar in all surveyed mines. Most mines had similar views about the desirability and frequency of crusher movement. The perceived need for in-nit crushing varied between copper and iron mining. The copper mines felt a greater sense of urgency for introduction of such a system, probably because typically greater vertical haulage is found in copper mines than in the iron mines. All mine personnel surveyed were interested in portable crushers and almost universally preferred gyratory-type primary crushers. They preferred large crushers, citing inherent reliability and durability, and the machine's relative freedom from clogging. Large size minimizes the number of crushers and conveyors needed. Analysis of desired crusher system characteristics (Table 1) fixed the crusher size at 1.5 x 2.3 m (60 x 89 in.). The 1.5-m (60-in.) feed-opening dimension could accept the largest material normally fed to the crusher, and the 2.3-m (894n.) head diameter could fulfill the 3.63 kt/h (4,000 stph) capacity requirement. Selected System Description The comments and analyses discussed in the contract report led to the design and refinement of a movable crusher system. This system represents the consensus of more than 100 mine workers and almost 50 construction and engineering company personnel. It is supported by more than 50 years of experience in crusher manufacturing. Although many alternatives are available for any given system, and selections are likely to be dictated by varying site conditions, the selected system is believed to be appropriate for most projected requirements. Final design would be dictated by mine operators during evaluation for approved projects. Detail design of the feed and discharge systems were not included in the study because they are mine specific. The basic system (Fig. 1) consists of a 1.5 x 2.3-m (60 x 89-in.) gyratory crusher on a structural steel frame. The frame is used as an operating platform for the crusher and as a carriage to move the crusher. The control tower includes a crusher lubrication room, a hydraulic equipment room, a switch gear room, a room for the motor control center, and a control room for operating the crusher and maintaining the equipment. The auxiliary system consists of a hydraulic rock hammer and pedestal crane with 74-t (80-st) and 14-t (15-st) hooks. Figure 1 also shows stairs, railings, and a work platform. Feed and discharge arrangements are shown on Fig. 2. The system shown is for mildclimate applications. Additional enclosure and heating would be needed for extremely cold weather conditions. Crusher A 1.5 x 2.3-m (60 x 89-in.) gyra¬tory crusher was selected for this application. This size can handle the typical throughput of 3-3.63 kt/h (3,500-4,000 stph) desired by the mines and the 1.3-m (50-in.) material to be crushed without difficulty. The crusher is the heaviest

Jan 4, 1983

By M. Sagisaka

The purpose of this study is to obtain carbon dioxide emissions by copper production systems and quantitative merit to use copper scraps in Japan. Electrolytic copper and sulphuric acid originating from the refining gas are produced in the system. In this study, the inventories such as the fuel consumption of the unit processes and the in-house electricity generation were obtained from published papers and public statistical data. The following observations were made based on the Life Cycle Assessment (LCA) method: (1) Carbon dioxide emissions from the production of electrolytic copper and sulphuric acid in the system are about 1.0 kg and 0.4 kg/kg-product respectively. The carbon dioxide emissions attributable to the transportation of copper concentrate correspond to 20% of the total emission. This emission is higher than that of zinc because the metal content in the concentrate is lower than zinc. (2) The carbon dioxide emissions from the system decrease with the recycling of copper scrap to the converting process because the consumption of copper concentrate is reduced. The reduction is estimated to be 0.18 kg-CO2/kg-Cu at the point of 0.1 kg-scrap/kg-blister Cu. This corresponds to 9% reduction for the present system. However, this recycling leads to the decrease of sulphuric acid by 450x103 tonne at the point. The recycling of scrap should be evaluated not only from the reduction of carbon dioxide emissions, but also in terms of sulphuric acid demands as well as advantage of waste management.

Jan 1, 2003

By K. Chandrasekaran

Carbon-in-leach (CIL) is conventionally used in gold processing operations when preg robbing components are present in the ore. The CIL process is becoming attractive even in other situations when preg robbing is not a factor. This article discusses the situations in which the CIL circuit can be applied. The results of leach-carbon-in-pulp (CIP) and CIL circuits at Newmont Gold's Mill No. 2, No. 4 and No. 5 are presented for comparison: Mill No. 4 was initially designed for a throughput of 4.1 kt/d (4500 stpd). It is presently operating at an average throughput of 6.6 kt/d (7300 stpd) without significant changes to the original design. The design considerations of the Mill No. 4 CIL circuit are discussed. The design of any processing facility represents a series of decisions. The final design options should ultimately be resolved based on economic as well as technical considerations. Every design decision represents some sort of compromise. From the designer's view point, these decisions are made with the conviction that the final product represents the most prudent long-term expenditure. The design throughput rate is a decision reflecting a maximum return for the capital and operating costs that the plant will incur over the life of the mineral resource. The result is a plant that is not operator proof or maintenance free because it would be too costly to build. At some point, the incremental increase in the level of capital expenditure would not adequately compensate for the lower

Jan 1, 1991

By J. Appleby

This paper reviews earlier in-plant testing at the Sidbec-Normines pelletizing plant at Port Cartier, Quebec, Canada. It describes the result of the more prolonged use of coke breeze during recent months and in addition, the effects of varying dolomite and coke additives upon the metallurgical properties of the pellet production have been studied. Mention is also made of some brief test work carried out to use peat moss as a carbonaceous additive to the pelletizing process and in particular the plans for future work in this respect. Earlier laboratory pot-grate test work had indicated that a production rate increase of between fifteen and twenty percent was a practical possibility, or alternatively that the plant could be run at design rating with significantly lower energy consumption. These energy reductions were of the order of ten to fifteen percent for fuel and main process fan power respectively. The physical and metallurgical pellet properties for both blast furnace and direct reduction furnace use were little affected by the production rate increases, and were actually somewhat improved when practicing maximum energy conservations. Pellet properties could be further improved by not extracting the maximum energy economy. Two phases of carefully controlled in-plant testing were run to assess the effect of energy conservation under plant conditions. These two phases of testing confirmed that an overall fuel saving of approximately fifteen percent could be realized, with a reduction in the Bunker C oil consumption of about forty-five percent, and a reduction in main process fan power of approximately ten to fifteen percent. The present scope of work is aimed at establishing the use of varying levels of coke addition up to about one percent under normal plant operating conditions.

Jan 1, 1980

By Steven E. Mischler, Jay F. Colinet

The Mine Safety and Health Administration (MSHA) promulgated a rule in 2014 that required numerous changes in compliance dust sampling requirements for coal mine operators. Two key parts of this rule were the lowering of the respirable coal mine dust standard from 2.0 mg/m3 to 1.5 mg/m3 and requiring operators of underground coal mines to use a continuous personal dust monitor (CPDM) for compliance sampling. The CPDM currently approved for compliance sampling is equipped with a display that provides miners with in-shift information on their respirable dust exposure. The goal was to provide an indication of a potential overexposure and empower the miner and mine operator to implement changes in controls and/or operating practices to prevent an overexposure from occurring.

By T. W. Conrad, B. Kerr

During the last decade grassroots minerals education programs have blossomed throughout the United States and in other countries. At the same time an environmental education movement has been gaining momentum. While this offers a unique opportunity to share the mining industry’s story, it also has some potential pitfalls. In this paper the authors will discuss some of the benefits of participating in environmental education and provide some practical tips for success, based on New Mexico experiences. It will conclude with a presentation on a successful environmental education program at Heights Middle School in Farmington New Mexico.

Jan 1, 2001