Search Documents

By K. P. Madhusudhanan, R. K. Bhatia, K. S. Narasimhan, R. N. Singh

A typical case study of a coal washery of capacity 500 t/h raw coal input has been presented and discussed with particular reference to the techno-economics for flotation column vis-a-vis the conventional flotation cells, keeping parameters like input capacity and product ash same. The results presented indicate that substitution of flotation cells by columns in a coal washery results in advantages of increased fine coal recovery, better quality of concentrates, lower capital and production costs etc.,. The effect of increasing the specific capacity of the column by design modifications on the cost benefit is also analysed.

Jan 1, 1988

By Graham G. W. Mustoe

Energy losses are important factors in a conveyor's performance and design. A significant energy loss due to belt sag within a conveyor system occurs when shearing motion between the bulk material particles occurs as the material moves along the belt. An initial analysis of these phenomena was performed using the discrete element method, which is a general-purpose numerical modeling technique for analyzing the mechanical behavior of particulate materials. The software used in this work was Overland Conveyor Company's, Chute Analyst Professional, a discrete element computer code designed specifically for analyzing bulk materials transportation and handling problems.

Jan 1, 2008

By W. Trask

The state of the art in crawler transporters for loads to 3 kt (3300 st) is sufficiently advanced to allow compilation of job cost figures showing the economics of tracked vehicle use under a wide variety of circumstances. Initial costs, cost per ton of capacity, and operational and maintenance expenses are presented. Data is derived from participation by the Neil F. Lampson Co. in more than 3 Mt - km (2.05 million st - mile) of crawler operation during the past 16 years. The effects of economics on future design trends will be examined with particular reference to versatility, portability, and capacity.

Jan 1, 1987

By Scott Stebbins

Cost estimating and economic evaluation software provide evaluators with the ability to predict the profit potentials associated with mine design alternatives even during project exploration and prefeasibility. Examining a multitude of development alternatives early on serves to identify aspects critical to profitability and to increase the reliability of economic projections. A case history illustrates how Sherpa Cost Estimating Software, when used in conjunction with Apex Software for Economic Evaluation, significantly enhances an evaluator's ability to examine design alternatives in a timely and reliable manner. The costs and economic impacts associated with various access routes, production rates, equipment mixes, and stoping methods are projected.

Jan 1, 2002

By Frederik P. Agterberg

During the past 20 years, methods of multivariate statistical analysis have been developed on mainframe computers for the integration of geological, geophysical, geochemical and LANDSAT data in mineral resource appraisal. At present, it is becoming increasingly feasible to perform mathematical image analysis of digitized patterns on microcomputers. This has led us to develop a new method of statistical pattern integration for mineral exploration. In this paper, the new method is used to outline, by means of posterior probabilities, exploration targets within small areas of which the prior probabilities for occurrence of new mineral deposits had been estimated by multivariate analysis.

Jan 1, 1989

By Richard H. Follis

Activated carbons used for precious metal recovery from carbon-in­pulp (CIP), carbon-In-leach (CIL) and carbon-in-column (CIC) circuits often become fouled with Inorganic precipitates (i.e., CaCOa, CaS04, SI02), and adsorbed organics (I.e., petroleum distillates from lubricants, dissolution products from wood) (1,2). These contaminants occlude carbon pore structure, such that diffusion controlled adsorption and desorption (elution) of Au(CN)2-and Ag(CN)2· are lmpeded(3,4l. Thus, after only short exposure to the hydrometallurgical environment, the characteristic carbon activity is reduced(5l. By frequently regenerating circuit carbons, activity losses associated with fouling can usually be minimized. Regeneration typically Involves (not necessarily Is this order): 1) elution to remove adsorbed ionic species (e.g., until they are removed from the carbon pore structure, Au(CN)2" and Ag(CN)2-are contaminants )(6l; 2) acid washing with 3-15% (wt/wt) hydro­chloric acid, to dissolve soluble Inorganic precipitates such as CaC03; 3) neutralization and/or water rinsing to remove residual acid; 4) thermal regeneration at 350-650 °C to remove adsorbed and/or pyrolyzed organ­ics; and 5) screening to remove fine carbon particles produced by Impaction and abrasion in the various stages of the hydrometallurgical circuit (i.e., adsorption, elution, and regeneration). The overall process Is purposed to reopen the circuit carbon pore structure, and to maintain the activity and qualities of virgin (new) carbon(7,8l. While most CIP, CIL and CIC operators regenerate circuit carbons, few evaluate the effect of the process on carbon quality in a systematic way. Process control usually Involves Iterating critical regeneration parameters such as: acid concentration; time frames for acid washing and water rinsing; and temperature and residence time for thermal regeneration. Carbon quality control frequently comprises only sporadic activity tests performed on non-representative grab samples dipped from conve­niently accessed carbon storage bins. So, regenerated carbon quality may vary and (at times) be unacceptable for effective hydrometallurglcal circuit operation. To verify the efficacy of the regeneration process and assure accept­able adsorption and elution rates for Au(CN)2· and Ag(CN)2·, operators should systematically assess regenerated circuit carbon quality. This paper, then, suggests methods for effectively assessing circuit carbon quality, Including: carbon sampling procedures; standardized physical and chemical test methods; and criteria and general procedures for comparative adsorption rate (activity) testing. Also, a two tier quality control testing scheme is proposed, and techniques for presenting and interpreting test data are demonstrated.

Jan 1, 1992

By Y. C. Kim

For the past few years, the Cyprus Bagdad Copper Company began experiencing a significant "ore-dilution" problem from its low grade open- pit copper mine located at Bagdad, Arizona. To pinpoint the causes of this dilution, a study was initiated to investigate as well as to improve in-pit ore-waste selection-procedures using conditionally simulated ore-bodies. Prior to the actual use of conditional simulation; a comparison of different estimation methods for a mined-out area in the pit was performed. Specifically, kriging estimates were compared against the original estimates of the company which were based on the polygonal approach. The results of this comparison clearly identified part of the so- called "ore-dilution" problem, which was the initial over-estimation of average ore grades from blast rounds, using the polygonal approach. The results from the use of conditionally simulated orebodies demonstrated that the "ore-dilution" problem can be reduced by more than half if in-pit ore- waste selection is based on the kriged estimates rather than the polygonal estimates. This simulation study also showed that the current use of the polygonal approach has the effect of shipping a larger tonnage of lower grade material to the mill.

Jan 1, 1982

By M. J. Friedel

The scale-dependent hydraulic properties in a fractured porphyry copper oxide deposit are investigated for relevance to In Situ Leach Mining (ISLM) design. In most well field designs, mine operators assume that hydraulic properties represent a continuous spatial function, or continuum. The problem, however, is that the representative elemental volume, the volume over which hydraulic properties are described as a continuum, is a domain (if it exists) that occurs between end members representing varying degrees of heterogeneity. At the Cyprus Casa Grande mine, transmissivity fluctuations are spatially correlated. This suggests that, at the scale of ISLM, the hydraulic process is heterogeneous, and a typical continuum representation is inappropriate for design. Alternatively, a conditional stochastic approach using the Simulated Annealing (SA) technique is deemed useful for the imaging of heterogeneous hydraulic properties. Specifically, SA preserves transmissivity extremes and spatial complexity, both necessary for accurate conditioning of a flow simulator. Also, the stochastic continuum approach provides an avenue whereby uncertainty (or risk) may be addressed. Currently, the SA weaknesses are that it is computationally time consuming and that uncertainty may increase when simulating under conditions of statistical isotropy. Recognizing that ISLM exerts a dynamic influence on hydraulic properties with time, the mine design should be re-evaluated at intervals throughout the evolution of the leaching process.

Jan 1, 1994

By F. Calizaya

This paper describes the basic requirements for the utilization of belt air to ventilate working sections at remote locations in relation to the main fans. It highlights the risks involved, potential problems, and the provisions that must be followed by mine operators for the safe use of belt air. The paper also presents a brief review of the current regulations, conveyor belting tests, atmospheric monitoring system requirements, and the experience gained by mine operators to utilize the belt entries to ventilate remote working sections or areas where mechanized equipment is being installed or removed. The paper concludes with a set of recommendations with respect to the utilization of belt air and the composition of belt material in under-ground coal mines.

Jan 1, 2008

By A. H. Sharbaugh

It is believed that considerable economic benefit would arise if run of mine (ROM) coal from the underground mines in the Winifrede seam could he enriched before shipment to the preparation plant by partial removal of the shale. Shale could comprise up to 50% of the ROM product. Complete mine-mouth separation is not necessary, but any process must be dry and have high Btu recovery. We have conducted a preliminary analysis of coal/shale mixtures from the Winifrede seam and we find that it is quite possible that a 50-50 ROM mixture of coal and shale could be converted to a 60-40 coal-shale mixture by inspection of individual lumps coming from the mine. The device would consist of a feeder/siever section to deliver the ROM coal > 5 cm (2 in) to an inspection station via a conveyor belt. This inspection station decides if a piece is coal or shale, and if it is shale, activates an air jet to blow shale off of the belt. We have evaluated a dielectric loss technique for the inspection device. The potential advantages of the dielectric loss method are high throughput, low capital cost, and no special handling or licenses would be required. Such a single lump inspection technique is made possible because of advances in high speed electronics and servo systems. This paper provides a summary of our analyses on the Winifrede coal sample, a description of a proposed apparatus to separate coal from shale, some of the experiments needed to demonstrate our ideas.

Jan 1, 1984

By James P. Ludwig

While we are all aware of the need for reclamation of mine sites, few managers and engineers seem to be aware that good reclamation begins with the earliest plans for mining and processing of ores. Far too often the attitude that reclamation is an add-on to worry about at the end of the mining process dominates the thinking of mine engineers and management, A common result is that the reclamationist can be faced with mining and waste disposal designs that are nearly impossible to deal with effectively from an ecological perspective. Everyone of us has been victimized by the down time and maintainence cost that resulted from the purchase of an outwardly attractive, but poorly designed piece of equipment. When confronted by design defects in equipment, a distraught owner can always trade it in, call a consumer advocate, or follow up one of the "lemon laws" at either the federal or state level. A poorly designed mine for reclamation purposes usually cannot be treated either with ease or cost effectiveness. Good reclamation can be effectively prevented by the designs used when the mine was planned. The purpose of this paper is to share some of the experiences our firm has had with reclamation projects at mines in the Upper Midwest as these were influenced or controlled by mine design decisions. My aim is to sensitize mine planners and managers to planning processes they should consider, and hopefully use, early in the mining process to assure successful reclamation during and after mining. Many of the examples I will cite are from experience gained at the recently closed Jackson County Iron Company taconite operation at Black River Falls, Wisconsin. I am particularly grateful to Mr. Vern Metzger, mine manager at JCIC, for his unflagging support of good reclamation practices, employee training programs (which have included reclamation techniques), and his forebearance to put up with our group of ecologists. I realize that this was a time when there were significant internal and external pressures to cut all costs including reclamation efforts. The collaboration has been successful as you will soon see.

Jan 1, 1984

By Levent Ozdemir, Roy H. Spitzer, Don W. Deere, John B. Blyler

This paper documents the construction of the Stanley Canyon Tunnel, the geologic conditions encountered, boreability of the rock, and the impacts of the conditions encountered on the construction. The 5.05 kilometer long (3.1 miles), 3.47 meter (11.4 feet) diameter, tunnel was driven through granites with a refurbished tunnel boring machine (TBM). Difficult ground conditions encountered included shear zones, high groundwater flows, and hard, tough, and strong rock. Detailed geotechnical studies during construction revealed that microscopic changes in the rock grain boundaries due to contact metamorphism, resulted in the hard boreability. Originally scheduled for five months, the tunnel construction required nearly three years, including periods of project shutdown.

Jan 1, 1995

By L. S. Gertsch, M. Z. Abu Bakar

Linear cutting tests of a porous sandstone with a radial drag pick show that saturation of rock with water can increase the specific energy of fragmentation. This appears to be due, in this case, to a saturation-induced increase in the forces acting on the cutting tool without a concomitant increase of the fragmented volume. The mechanisms of this reaction are explored by examining various responses of the parameters controlled and induced during the linear cutting tests, such as cut spacing, cutter penetration, three-dimensional forces and muck production. A program of load-indentation testing is underway to evaluate the permeability threshold of this behavior. These findings are opposite from those made when the same rock is cut with a constant cross-section disc cutter reported elsewhere (Abu Bakar and Gertsch, 2011). Such results highlight the effects of different cutting tool designs, and indicate the need for a well-coordinated program of research to support effective excavator design and selection.

Jan 1, 2012

By D. C. Shumway

Recently, the health of the cement industry has been threatened by the impact of environmental regulations, over-zealous state and federal agencies and radical environmental groups. Unfortunately, cement plant operations tend to trigger every environmental regulation and program promulgated, plus several programs designed specifically for the cement industry. These environmental burdens come at a time when the cement marketplace has been impacted by imports resulting in a situation where it has been difficult to increase prices to offset these increased environmental liabilities. The competitive world market forces the cement industry to seek creative ways to reduce costs. With additional major environmental programs coming down the pipe, like the Federal Clean Air Act Amendments of 1980 and EPA regulation of cement kiln dust, the cement industry has attempted to try innovative supplements to cement manufacturing. The cement industry has found that using waste tires, biosolids and other solid wastes in the cement manufacturing process can reduce costs and plant emissions.

Jan 1, 1996

By William R. Bond, Jim V. Rouse, Laura L. Damon

As noted by Damon (1990), "The time that a heap (of gold ore) is on the reusable leach pad is of critical economic importance." The Interim Neutralization Study, conducted by Brohm Mining Corporation (Brohm), at the request of the South Dakota Department of Water and Natural Resources and reported by Damon indicated that improvements could be made in leaching and pointed out the need for a better understanding of the gold ore leach procedures. To provide data on an actual heap, personnel from Brohm and GEOCHEM installed a series of pressure/vacuum lysimeters in an active Brohm heap, and conducted subsequent testwork to evaluate the efficiency of leaching. The objectives of the testwork included efforts to:

Jan 1, 1992

By V. Dezelic, D. B. Apel

This paper describes the results of laboratory and field experiments conducted to determine the applicability of Ground Penetrating Radar (GPR) for the assessment of the strata thickness and for the identification of separation between bedding planes in stratified rocks. The knowledge about the extent of such separation in the roof layers and information about roof lithology can be used to determine the roof support requirements for underground mines where stratified rocks are present. The laboratory and field experiments were conducted at the Rock Mechanics Laboratory and the Experimental Mine at the University of Missouri-Rolla. The 1.5 GHz high resolution, shallow depth GPR antenna was used for all of the experiments.

Jan 1, 2004

By I. E. Lewis, W. R. Hopkins

Flowsheet improvements, such as series/parallel SX plant configurations, discontinuation of plant sumps and improved filter pumping concepts, the use of in-settler baffle systems, and the Krebs and combined mixer-settler designs offer opportunities to reduce SX plant cost. Today's plants employ permanent cathodes and mechanical stripping, and the increased capital cost can be offset by labor savings and higher current densities. The wider use of HDPE and new cell construction materials also reduce capital cost. The "Portelex" type of relocatable design embodies such new, cost-saving measures in a simple basic plant. Organic inventory and losses are reduced by new, fast-settling, hybrid organic reagents with improved kinetics and selectivity.

Jan 1, 1991

By Raphael Mourad, Colin R. Phillips

Investigation of the traps in LiF:Mg, a multi-peak phosphor, was carried out using simple phosphorescence decay analysis. Half lives at room temperature of the trapping centres (peaks -lb, -la, -1, 0, 1, 2, 3a and 3) in the phosphor after irradiation with [a] radiation were found to be 3 s, 5 s, 28 s, 4 min, 15 min, 1 h, 6 h and 2 d respectively. Justification for the method of analysis is pro- vided and the results of measurements compared with published data. The effects of pre-annealing at 400°C for 1 h and 80°C for 24 h on the trapping configuration and on the trapping efficiencies were also studied.

Jan 1, 1981

By D. T. Kinard, A. A. Schweizer

An operational 9 meter (30-foot) high gold heap leach pile was investigated by excavating test pits up to 6 meters (20 feet) deep, obtaining bulk and relatively undisturbed thin wall drive samples, and observing the ore distribution patterns exposed in the test pit walls. The clayey ore is crushed, agglomerated with lime and cement, and deposited on the leach pads using a radial stacker. Laboratory tests performed included moisture-density, gradation, compaction, Atterberg limits, permeability (constant and falling head), and triaxial strength tests. Discussion is presented on the effects of agglomeration on the permeability and strength characteristics of the in-place ore. Also discussed is the effect of deposition of the ore using the radial stacker.

Jan 1, 1987

By Bok-youn Kim

Presently, mobile diesel equipments contributes a lot in improving the economical feasibility of underground mining and tunneling operations. Even in Korea, quite a large number of diesel equipments is being applied to the underground workings already. This paper introduced the production procedure, characteristics and evaluation technology on diesel particulate matter(DPM) that is known as a carcinogen For easy measurement of DPM using laser dust monitor, the conversion factor(K) to gravimetric concentration was acquired. The field measurement of DPM was conducted to make a comparison between locally manufactured on-road equipments and imported equipments specially designed for underground use. According to the Government regulation revised h 1996, it was learned that the critical pollutants among the diesel exhaust is DPM instead of NOx which have been considered as a critical pollutants.

Jan 1, 1997