Search Documents

By Nan Hua

As a high production and high efficient mining method, top coal caving method is now widely used in China. However, as more extra-thick coal seams are mined, it becomes more and more difficult to make the top coal fully broken up, resulting in more and more top coals flowing into the gob, rather than onto the rear AFC at the working face as designed. This research is aimed to investigate the failure mechanisms of the extra-thick top coal caving mining method.

Jan 1, 2009

By A. W. Khair

This paper deals with the design characteristics of cutting tools and the operating parameters these tools are usually subjected to. Eight types of cutting tools/bits with different geometrical shapes and sizes were tested in a linear cutting apparatus, utilizing concrete blocks. The objectives of these experiments were to study the performance of each type of bit, make qualitative assessment of each bit geometry and size and establish cutting parameters for efficient utilization of the tools. During the experiment required forces Fx, Fy, and Fz, cutting, penetrating and lateral forces respectively and audible and sub-audible noises were measured. In these experiments, the depth of cut was kept constant to 1.5 inch while the bit spacing was varied 1.5,2.25 and 3.0 inch (3.75,5.6 and 7.5cm respectively). The results of these experiments indicated that by optimum ratio of depth of cut to bit spacing, the cutting face will be cleaned with the least ridge/land remains between the bit groves, resulting in least specific energy consumption, more large and less fine product particles and substantial reduction of audible noise. The results of these experiments also showed that proper bit design not only decreased cutting energy consumption but also reduced audible noise.

Jan 1, 2001

By O&apos

Southern Ohio Coal Company (SOCCO) and the U.S. Bureau of Mines have identified techniques to optimize the use of scrubbers on continuous miners. The techniques provide maximum respirable dust control while maintaining a high output. The use of radio remote control and scrubber help to achieve greater advance between lifts by locating the operator in fresh air during the mining cycle. He is also kept away from newly exposed roof, which is not supported. An alternative to fan-powered scrubber was also evaluated at SOCCO. A high-pressure water-powered scrubber system eliminated the noise associated with fans, and achieved an intrinsically safe system. Experience in the use of these scrubber systems and remote control at SOCCO are discussed.

Jan 1, 1990

By L. W. Scott, T. H. Dubaniewicz, F. T. Duda, P. G. Kovalchik

Recent research conducted by NIOSH's Pittsburgh Re¬search Laboratory showed that electrical current levels permitted under present regulations may not limit cable temperatures to less than 90°C in reeled trailing cables. Reeled cables, which are tightly wrapped with many turns and which carry current in an enclosed space, can become overheated due to poor heat transfer. This overheating can cause the cable insulation to soften, making them prone to damage. The damaged insulation reduces the life of the cable and can lead to shock, electrocution and mine fires. This paper describes a method of measuring the conductor tem¬perature of mine trailing cables during normal operation. The temperature is measured using a 50/125-, µm graded index multimode optical fiber located in the center of the metallic conductors. Distributed temperature measurements are made using an optical time domain reflectometer (OTDR). This system is capable of measuring temperatures with an accuracy of ± I °C over a length of 4 km at I -mintervals. With this unique way of measuring temperature, tests can be conducted that simulate actual mine conditions. The tests provide important data that allows MSHA's Approval and Certification Center to develop approval criteria for cycli-

Jan 1, 2000

By K. Biswas, S. J. Jung

Health and safety of workers in mineral industry in the U.S. is still a vey important issue as Mining along with Agriculture, Forestry and Fishing and Construction industries have contributed most of the fatal occupational injuries ill between 1980 - 1995 (Worker Health Chartbook, 2000). Health and safety issues, especially for the mining or related excavation industries, arise either from exposures of the human workers to the contaminants liberated or generated by mining operations that have adverse effects on human health (for example coal dust etc.) or from the exposures of the human workers to hazardous working environment that constitutes mining operations (for example blasting etc.). One of the biggest challenges is to understand the combinatorial effect of numerous work-condition (e.g. exposure to dust) and human-factor (e.g. smoking habit) variables on a health or safety-condition variable (e.g. incidence rate of a disease). This paper uses an example dataset on Coal miners' cough problem to illustrate the applicability of Generalized Linear Modeling (GLM) in understanding the relation between cough and other response variables, such as, age, height, smoking habits, time of underground exposure etc.

Jan 1, 2002

By D. M. Abbott

The requirements of the International Mineral Property Valuation Standards Template (IMVAL Template) (includes Petroleum), 4th edition of April 14, 2021, are based on six principles: 2.1.1 competence, 2.1.2 materiality, 2.1.3 transparency, 2.1.4 objectivity, 2.1.5 independence, and 2.1.6 reasonableness. The IMVAL Template describes “reasonableness” as, “The Valuer must ensure the Reasonableness of the Valuation. Any Valuation, assumptions applied, and any method relied upon should be reasonable within the context of the purpose of the Valuation and the Basis of Value. A method applied to the subject Mineral Property should be within the expected capability and consideration of an assumed likely buyer or lessee of the property.” The IMVAL Template’s Guidance 3.6 on Reasonableness states, “The test of Reasonableness is to consider what appropriately qualified and experienced Valuers, acting reasonably, would conclude in the circumstances. The Valuer must form an opinion that is reasonable in the circumstances, that is, what a Valuer believes is rational and plausible in the circumstances and would be viewed as such if considered by other appropriately qualified and experienced Valuers with the same information and at the same time.” Finally, the IMVAL Template’s Definition 4.26 states Reasonableness “[m]eans that other qualified and experienced Valuers with access to the same information for the same Valuation Date and Basis of Value would consider the Valuer's estimate of Value to be within a reasonable range.”

Mar 2, 2022

By Claes G. Björk

Over the past decade mined unlined rock cavern storage for crude oil and refined products has become economically more attractive. This trend is likely to continue, primarily due to advances in excavation methods, rising steel costs for above ground tanks and larger capacity requirements. The construction experience related in this paper comprises the excavation of more than 80 storage facilities (total capacity 90 million bbl) for crude and refined products ranging from propane to heavy fuel oil. This paper also deals with the experience gained as well as the problems derived from the utilization of these oil storage facilities.

Jan 1, 1981

By S. K. Kawatra, A. K. Bakshi

An on-line rheometer was developed to monitor the slurry rheology of a thickener underflow. The thickener processed a chalcopyrite flotation concentrate having a top particle size of 125 µm and a solids content of 30% to 60% (by weight). The slurry also contained residual flotation reagents, resulting in hydrophobic particles. Polymeric flocculants and lime were added to the thickener to flocculate the particles. Using the on-line rheometer, the slurry was found to exhibit pseudoplastic behavior with no yield value. It was also determined that factors other than the percent solids were responsible for changes in the slurry rheology.

Jan 1, 1999

By Randal J. Barnes

There are many methods available for the estimation of geologic parameters (Popoff, 1966; Barnes, 1980). In the last decade a new and relatively sophisticated technique using statistical theory has emerged: geostatistical kriging (David, 1977; Journal and Huijbregts, 1978; Rendu, 1978). An interesting property of geostatistical estimation is that when a geologic parameter is estimated for a given volume, not only is the estimate generated but an associated measure of certainty is produced as well. This statistical measure of estimation confidence is called the estimation variance. While the concept of an estimation variance is universally considered to be a good idea, mining engineers and geologists do not currently have the tools to incorporate it into their planning and quantitative analysis. This paper attempts to develop and present some of the necessary tools required to incorporate estimation uncertainty into mine planning. Geologic uncertainty is portrayed as an economic business risk. This risk is objectively characterized, and-the associated cost is quantified. Geologic delineation sampling is viewed in this light as an economic commodity with an associated cost and value. A coal mine planning example is used as a focus in this presentation. The data used is real, though it has been modified to maintain data security and project anonymity.

Jan 1, 1986

By H. J. Ilgner

Previous applications for using waste rock for backfilling in South African gold mines were reviewed and it was found that in many cases the mechanical equipment selected and the design philosophy applied did not meet the requirements. A more simplified system configuration is proposed, which allows the equipment to be relocated as mining progresses. Innovative high-intensity grinding and dense-phase pumping technology are proposed to provide a low-porosity backfill with a particle top size of 5 mm to 8 mm. According to recent rock mechanics modeling work, this comminuted waste backfill material can provide a good compromise between underground support characteristics and reliable hydraulic transportation behavior.

Jan 1, 2001

Health and safety issues are very important to the mining industry. Although the application of scientific research and current technology shields workers from many dangerous aspects of mining, accidents do happen. Many companies and institutions worldwide have committed to a continuous effort to minimize such occurrences. In this study, the health and safety data pertaining to the Greek mining and quarrying industry for the last three decades are presented and critically evaluated with respect to factors such as the number of workers and annual production. Appropriate indices are also calculated regarding the incidence and frequency of accidents. Health and safety issues specific to mining in Greece are also discussed.

Jan 1, 2002

By D. Tao

The reverse cationic flotation is the most widely utilized flotation method for concentrating iron ore. In such a process quartz is often floated with ether amines (R?O(CH2)3?NH2) partially neutralized with acetic acid. However, it is well known that the cationic flotation of hematite does not work well if a certain amount of slime is present in ore slurry. To improve flotation performance, starch is often added to the flotation feed to selectively flocculate and depress the iron minerals and sodium silicate is used to disperse the silica gangue. The present study was conducted to improve the flotation efficiency of iron ore flotation by use of a new type of depressant for clay and iron minerals, i.e., GP clay binder. It is postulated that the GP clay binder minimizes slime adsorption on quartz and hematite particles by agglomerating clay particles to reduce their surface area. It is further theorized that the clay binder helps depress hematite flotation due to its unique chelating ability to iron ion. The results from this study clearly show that the GP clay binder is an effective depressant in iron ore flotation. When it was used as a substitute for corn starch, it increased concentrate grade from 60.78% to 67.67% and increased iron recovery from 71.96% to 72.90%. The combined use of GP clay binder with corn starch produced even better flotation performance, increasing concentrate grade to 67.08% and iron recovery to 78.15% simultaneously. Key words: Clay Binder; Depressant; Iron Ore; Flotation.

Jan 1, 2009

By T. Brozell

"Communities near sand mines and processing facilities in Wisconsin have raised concerns regarding possible exposure to ambient respirable (PM4) crystalline silica. Fenceline PM4 (particulate matter captured with a 50 percent cut size of 4 micrometers aerodynamic diameter) crystalline silica concentration data were compiled at Fairmount Santrol Inc., Mathy Construction Inc. and U.S. Silica facilities. The long-term average PM4 crystalline silica concentrations ranged from 0.05 to 0.45 micrograms/m3 when sample values below the limit of quantification were treated as zeros. All of the long-term average concentrations were less than 20 percent of the Minnesota Department of Health’s and California Office of Environmental Health Hazard Assessment’s PM4 crystalline silica chronic reference exposure level of 3.0 micrograms/m3. The measured concentrations were consistently within the local background concentration range.Air Control Techniques P.C. compiled the sampling data using Thermo Fisher Scientific Inc. Partisol 2000i PM2.5 samplers meeting the requirements of 40 CFR Part 50, Appendix L. These samplers were adapted to capture particulate matter with a 50 percent cut size of 4 micrometers. The use of polyvinyl chloride filters allowed for crystalline silica X-ray diffraction analysis by NIOSH Method 7500. The combined use of adjusted PM2.5 filter-based samplers with Method 7500 crystalline silica analyses provided for a highly sensitive limit of quantification of 0.31 micrograms/m3 of PM4 crystalline silica.BackgroundIn 2005, the California Office of Environmental Health Hazard Assessment (OEHHA, 2005) adopted a 70-year chronic reference exposure level (REL) for PM4 (particulate matter having aerodynamic diameter of 4 micrometers or less) crystalline silica. The REL was extrapolated from occupational hygiene epidemiological studies, essentially all of which were based on in-plant PM4 crystalline silica measurements. No well-established ambient sampling technique for PM4 crystalline silica was available at the time that OEHHA adopted its REL. The personal samplers used for the National Institute for Occupational Safety and Health (NIOSH) Method 0600 in-plant sampling of employee exposure were designed for concentrations higher than ambient levels. The limit of quantification (LOQ) of PM4 crystalline silica on NIOSH 0600 filters was too high for the effective sampling of ambient air."

Jan 1, 2015

By Michel Grenier, Mahendra Gangal

Two methods used to measure the exposure of mine workers to diesel exhaust particulate were compared. One method was developed by the U.S. Bureau of Mines and the University of Minnesota's Particle Technology Laboratory. The method which was originally developed for use in coal mines is a size selective sampling technique. The other method uses an “ashing" approach to assess the exposure to diesel particulate. This second method is based on the principles of sampling according to the ACGIH respirable dust sampling criteria and the use of a silver membrane filter as collection substrate. Because a silver membrane filter is used, both respirable combustible dust (diesel particulate) and respirable silica can be measured from one sample. The comparison study took place in a Canadian lead-zinc mine during tests which were primarily designed to evaluate the gaseous and particulate emissions characteristics of new diesel engine technology. The study has shown that under the test conditions encountered, some differences were observed between the results as obtained by the two methods. These differences seem to depend on the characteristics of the respirable dust found in the work- place, i.e., size and composition. The impact, on sampling and analysis of diesel particulate, of the proposed guideline (ACGIH) for a TLV® of 0.15 mq/m3 is discussed briefly.

Jan 1, 1997

By R. L. Grayson, L. L. Probert

A three-year project focusing on the depth profiling of respirable coal mine dust particles using scanning electron microscopy coupled with energy dispersive X-ray analysis resulted in the development of statistically classified particle-behavior models. The models depict the changing silicon fraction for particles at 5-, 7-, 9-, and 11-keV accelerating voltages, thereby giving a clear indication of the nature of various types of mineral particles. This paper focuses on the results for respirable quartz particles sampled from five underground coal mines across the US. Through statistical analysis of results the relationship between the fraction of surface available quartz in respirable dust samples and coal rank is established for three Pennsylvania coal seams.

Jan 1, 1995

By Dipak D. Shah, Sajjan K. Jain

An interceptor sewer, 2103 linear meters (6900 Ft), 1.52 meter (5 ft) in nominal diameter, is installed by a direct pipe jacking system utilizing a remotely controlled fully automatic slurry shield machine called "Unclemole". The system involves placement of custom designed fiberglass pipe with Unclemole. The sewer alignment is along a heavily travelled thoroughfare in Staten Island, New York with invert varying from 20 meters (65 ft) to 28 meters (92 ft) beneath the road surface, and passes through soils of Glacial and Cretaceous origin. Dewatering was carried out at the jacking and receiving pits. Details of ground conditions, the pipe jacking system and method, and tunneling experiences are herein described.

Jan 1, 1991

By Erik Sundström, Magnus Nygren

The study explores the influence and consequences of safety initiatives on the development of safety cultures in the Swedish mining industry. It involves interviews with experts from four mining organizations, highlighting themes such as organizational structures, safety leadership, feedback, and communication.

Nov 1, 2023

By Robert G. McLusky

Since 1998, environmental extremists have waged war with the central Appalachian coal industry in West Virginia and Kentucky. In particular, they have filed three lawsuits challenging the legality of excess spoil ‘valley fills’ under CWA, NEPA and SMCRA: 1) Bragg v. Robertson, 72 F.Supp. 2d 642 (S.D.W.Va. 1999), rev’d. 248 F.3d 275 (4th Cir. 2001); 2) Kentuckians for the Commonwealth v. Rivenburgh, 204 F.Supp. 2d 927 and 206 F. Supp. 2d 782 (S.D.W.Va. 2002), rev’d. 317 F.3d 425 (4th Cir. 2003); and 3) OVEC v. Bulen, 2004 U.S. Dist. LEXIS 12690, July 8, 2004; OVEC v. Bulen, 2004 U.S. Dist. LEXIS 16078, August 13, 2004.

Jan 1, 2005

By L. Lacerda, C. Rose, E. Zellers

Approximately six hundred air sample measurements were taken at several U.S. underground metal/nonmetal mines in 1998 and 1999. This air sampling effort was organized by the Nevada Mining Association to evaluate mining conditions and to evaluate the Mine Safety and Health Administration’s (MSHA) Proposed Rule on Diesel Particulate Matter Exposure of Underground Metal and Non-metal Miners. MSHA’s proposed air sampling method, NIOSH Method 5040, was tested under controlled conditions and under normal mining conditions. Unfortunately, NvMA sampling results have indicated that carbonaceous rock dust, oil mists and even cigarette smoking create severe sampling interference problems for NIOSH 5040.The main conclusion was that NIOSH 5040 did not distinguish between DPM and other airborne carbon particulate. Thus, it is not a reliable method of accurately and unequivocally measuring DPM in underground metal/nonmetal mines.

Jan 1, 2000

By Ian McFeat-Smith

Despite a present, short-term economic recession, a remarkable enthusiasm exists in Hong Kong for building infrastructure including major tunnel projects. This paper provides details of current and recent bored tunnel works together with an insight into the impressive list of future underground projects planned by the MTRC,KCRC, Highways Department and Drainage Services Department for the next decade. Risks for each of these works including pipejacking, mixed face and rock tunnelling generally in Hong Kong are also identified. From this is evident that the scale and difficulty of such works continues to increase, requiring the use of more sophisticated methods of construction, the need for better methods of assessing and managing risks and for Government to utilize improved, more equitable Conditions of Contract for such major tunnelling projects.

Jan 1, 2001