Search Documents

By A. Haghighat

A risk analysis on mine fires for all U.S. underground coal mines from 2000–2012 was completed to identify locations that have a high risk for fire incidents. The data for this analysis was extracted from the Mine Safety and Health Administration’s (MSHA) mine fire accident reports database. After identifying fire incidents from this database, a risk matrix was developed for underground locations that showed a significant propensity for fire incidents. This matrix associates the hazards and risks with the severity and frequency of their consequences at each location. These significant mine areas will be the concentration of future studies in fire behavior, suppression techniques, and simulation methodologies. INTRODUCTION Fires in underground mines pose significant hazards to personnel because of inherent restrictions to movement and limitations to egress routes. Despite improvements, mine fires remain serious hazards in underground coal mine. In order to better mitigate the risks from fire hazards in the modern underground mining environment, a better understanding of where fire events occur must be gained. The following paper presents an investigation on the number of fatal and non-fatal incidents in underground coal mines fires from 2000 to 2012. Three phases of risk assessment (i.e., risk identification, estimation, and evaluation) were applied to the recorded fire events from the MSHA incident database that occurred during this time period. Using this process, a fire hazard was first defined. This definition was then used to identify any incidents that had occurred as a result of the defined hazards. The seriousness of the injuries and damages were finally quantified for each incident though an estimate of severity and frequency and then aggregated according to underground location (ISO, 1999; Van Duijne, 2008). Using this approach, locations prone to incidents resulting from fire hazards were first identified. The risk for the occurrence a fire incident in general was then estimated for each of the identified locations. The results of this assessment will be used to improve fire simulation techniques for the identified, high risk underground locations. RISK IDENTIFICATION A risk for this assessment was defined as any single occurrence of a fire initiated by the ignition of gas, dust, or electricity. Each recorded occurrence of such an event in the MSHA incident database was counted as a single fire incident. Both non-fatal incidents that were reportable but did not result in a fatality and fatal incidents that fell into the aforementioned criteria were counted. Incidents in the MSHA database that were already classified as “generic” were not considered. The remaining incidents were then totaled and aggregated according to the underground location in which they occurred. In previous studies, a number of locations, which are listed in Table 1, were highlighted as high fire hazard areas (McDonald et al, 1980; Pomroy et al, 1995; De Rosa, 2004). These locations were used to group the fire incidents extracted from the MSHA incident database. The compiled numbers of non-fatal and fatal underground coal fire incidents from 2000 to 2012 are displayed in Table 1.

Jan 1, 2019

By K. Vanbroekhoven

An industrial site near the centre of a historical town in Flanders is characterized by chromium(VI) contamination of the groundwater. Since the potential for natural attenuation was not sufficient to control the groundwater plume as observed from different analyses like pH, Eh, soil oxidation and reduction capacity, the feasibility of site remediation based on in-situ bioprecipitation of chromium was examined in lab microcosm studies. By creating reducing conditions by addition of a carbon source in the groundwater, chromium(VI) can be biologically reduced to chromium(III), which can form an insoluble precipitate of chromium(III) hydroxide. Microcosms contained contaminated groundwater and aquifer samples that were collected and manipulated under anaerobic conditions. Three different carbon sources were screened for their effectiveness: molasses from sugar beet production, molasses form starch production (protamylasses) based on potato juice and lactate. The different concentrations of sugar molasses were used to determine the optimal conditions. A range of parameters was monitored at regular time intervals for a period of six months such as chromium(VI) and chromium(III), DOC, methane, pH, Eh. A rapid conversion of chromium(VI) to chromium(III) was observed for all conditions tested. However, extensive removal of chromium from the groundwater by precipitation was only achieved for a limited number of conditions. In general, lactate was found to be the most effective carbon source, slightly better than the lowest concentration of sugar molasses that was tested, which itself was more effective than molasses based on potato. Higher concentrations of molasses, although causing a steeper decline in redox potential, resulted in less effective Cr removal. Typically, the fermentation of molasses results in acidification and this drop in pH may hinder the formation of insoluble chromium(III)hydroxides. It may also be possible that certain components of the molasses form soluble complexes with chromium(III). For lactate, no significant drop in pH was observed. Following the laboratory microcosm tests, the stability of the chromium precipitates was examined by performing a sequential extraction on the microcosm materials. These were performed under redox conditions which were similar to the ones observed in the field. Since the outcome of these tests was positive, a pilot scale test was implemented in the field in April 2005. Two different substrates, the cheap waste product sugar molasses and lactate are being injected creating two different impact zones and typical parameters are monitored. Frequent re-injections were important to maintain reduced conditions and are carried out three-weekly up to now. To study the stability of precipitates formed, mesocosm socks containing aquifer material were installed in the monitoring wells and harvested at regular intervals. Results of this pilot test will be presented and compared to the laboratory results. Based on the success of this field test, a full scale process will be designed and implemented as remediation strategy.

Jan 1, 2006

By Michael C. Stanley

The set of discoveries for a mining district or camp is a reflection of the exploration history. In the western Abitibi greenstone belt of Ontario, future exploration can be guided by a study of statistical trends of known gold deposits. In this area simple trends indicate a strong decrease in the contained quantity of gold discovered through time. Much of this decrease is attributed not to falling mining grades but to smaller tonnages of ore. A plot of the largest discovery in each ten year time period suggests that deposit discoverability is following a size-biased sampling model. Cumulative ounces of discovered gold indicate that an asymptotic value has been reached where exploration is not expected to add significantly to known reserves. This is substantiated by a downward trend in the exploration success ratio of the number of new deposits discovered versus the number of new mineral prospects. The set of discovered deposits reflects a non-random sampling process where size- biased modeling suggests that the largest deposits will be discovered early in the exploration effort. It is the exceptionally large deposit contributing to the observed size-biased distribution. Although this pattern is observed for the western Abitibi the model is complicated by recent, large reserve additions that are attributed to the original discovery. There is present in this area a subtle learning process in exploration leading up to the largest discovery. For comparison a learning model was estimated using cumulative size of discovery per unit of time. This model yielded results consistent with the statistical trends and is thought to be a superior forecast of future discoveries in this region.

Jan 1, 1992

By Zhen-xing Diao, Feng Zhao, Ya-dong Xue

"Two important aspects of excavation performance of TBM are advance rate and cutter replacement/ring consumption, which is closed to the cost and construction duration of the project. To achieve this, a database of TBM parameters and the geological-geotechnical conditions during the excavation of Yinhanjiwei was compiled and analyzed. Relationships between different geological and TBM operational parameters were investigated. Results of analyzes show that there are qualitative correlation between Field Penetration Index (FPI) and rock geological parameters. And strong relationships between FPI and operational parameters are suggested. In this study, the cutter replacement and ring consumption were analyzed using statistical method for preliminary estimation in similar conditions. 1. ITRODUCTION Hard rock TBM is widely used in tunneling project nowadays because of its advantages to conventional drilling and blasting, especially in long tunnels. The biggest advantage is its high advance rate. However, rock conditions of tunnels are complicated. So TBM performance becomes a primary topic in tunneling engineering, which includes of rate of penetration, utilization, daily advancement, cutter consumption and so on. Many prediction models have been developed to estimate the TBM performance in the project planning phase. The most widely accepted and used models around the world are semi theoretical CSM model (Rostami and Ozdemir, 1993; Rostami, 1997) and the empirical NTNU model (Blindheim, 1979, Bruland, 1998).With increasing uses of TBMs in different ground conditions, an increasing number of researchers have developed new models in order to predict the performance of TBM more accurately in similar geological conditions.(Gong and Zhao, 2009; Hassanpour et al.,2009, 2010, 2011, 2014; Delisio et al., 2013; Delisio and Zhao, 2014)"

Jan 1, 2016

By Robert J. Timko, R. Lincoln Derick

The Bureau of Mines evaluated the integrity of escapeways in a three entry underground coal mine. A center conveyor belt entry (secondary escapeway), was flanked by an intake (primary escapeway) and a return entry. Diesel equipment was used throughout the mine for material and personnel haulage. A carbon monoxide monitoring system, tied to a data recording computer on the surface, was deployed throughout the belt entry and at selected sites in the intake and return entries. Previously, the company had a fire of unknown origin in another mine, which prompted an interest in the performance of their escapeways. An initial, qua1itative evaluation was performed by burning approximately 14 kg of coal at the mouth of the intake entry. The first test was followed by a similar burn at the mouth of the belt entry. These initial trials showed a high quantity of leakage between entries. In several follow-up evaluations, simulated fires, using a tracer gas, were set in the intake and belt entries. Tracer gas concentrations were obtained in all entries at four different underground locations. The results of these tests showed that permanent stoppings could not guarantee isolated, contaminant-free escapeways.

Jan 1, 1989

By Chester O. Ensign

The White Pine Mine is situated in the southwestern portion of the Keweenaw Peninsula of Upper Michigan approximately 6 miles south of Lake Superior (Fig. 1). It is east of the Porcupine Mountains in Ontonagon County. The ore deposit is about 70 miles southwest of the famous native copper deposits of the "Copper Country" lying northeast of Houghton. Geological conditions are different at every mine and create a special set of problems in dilution control. This paper is largely intended to describe the techniques applied in mine dilution control (grade control) at White Pine, and present results of the program. For necessary background information major geologic characteristics of the deposit, particularly those that exert control over the distribution of ore, are briefly discussed. Mining methods are described in considerable detail since applied grade control techniques are adapted to these.

Jan 1, 1964

By M. Yavuz

Decision Making (DM) can be defined as a selection process of the best one among the alternatives sets in order to obtain goal, and mostly has an uncertain situation [7]. Every mining engineer is subjected to a number of mining DM problems in daily mining operations. In reality, all stages of mining have its own DM problems. Most of time, engineers do not use scientific methods for DM problems. These problems can mostly be solved by the engineers according to their past experiences and practical studies. Mining engineers often use their intuition in DM process. Experience and intuition have been central to DM because of the frequent lack of quantitative data including geology, grade distribution and ground condition, as well as environmental, social and economic factors [8]. In decision process, linguistic variables become in question and decision makers may not know how these variables are computed [9]. So, the DM process may be qualitative, quantitative or combination of the two. The problem structuring and analysis process is conceptualized in Figure 1 [8]. The qualitative analysis is based primarily on the judgment, knowledge and experience of an expert (or team of experts). In a quantitative analysis, the focus is on facts and the data associated with a problem and a mathematical formulation that encompasses the objectives, variables and constraints of the particular problem. The quantitative analysis has traditionally been the subject of operation research and management science [8].

Jan 1, 2008

By Henry J. Jacoby

This report concerns Contract No. 3B of the Port Richmond Project, for the Department of Water Resources of the City of New York. It involves the construction of 7, 000 ft. of 7 ft. finish I. D. interceptor sewer by tunneling in soft ground, as well as associated manholes, regulator chambers, siphons and miscellaneous sewers and structures, beneath a heavily travelled perimeter road in Staten Island. The Contractor is Richmond Constructors, a joint venture of Grow Tunneling Corp., sponsor, MacLean Grove & Company, Incorporated, Morrison-Knudsen Company, Inc., and Andrew Catapano Co., Inc. Project manager is Paul DeMarco, Vice-President of Grow Tunneling Corp. The cortract, as designed and bid, requires the use of liner plates 101 -0" O. D., and both cast iron and steel designs of several widths were included in the bid documents by the owner. The specifications also required the contractor to install and put into operating condition, prior to commencement of mining, a complete low pressure compressed air plant and all accessories for mining in compressed air, even though the contractor was given the option of using other methods of ground water control. A third requirement of the specifications was that a shield be used, either manual or mechanical, and with full provision for "breasting". BACKGROUND The first soft ground shield driven tunnel in the United States was in New York City and was built under Broadway in lower Manhattan in 1869

Jan 1, 1974

By P. Mousset-Jones, G. Danko

Rock thermophysical properties, i.e. heat conductivity and thermal diffusivity, were obtained for reference values at the Waldo Test Mine for mine fire simulation purposes. An in situ measurement method was chosen since it could include the effect of rock fractures. The REKA method (Rapid Evaluation of k and alpha) was used because it can measure conductivity (k) and diffusivity (alpha) simultaneously within an eight-hour measurement period. A total of six measurements were taken in three different holes, and at two different depths from the collar of the hole. Each measurement provided an averaged conductivity and diffusivity for a volume of rock of approximately one cubic meter. The boreholes were driven into the upper and lower limestone, two at right angles to and one parallel to, the stratification of the rock. Significant representative conductivity and diffusivity values were obtained for the whole mine by averaging the six measurement results. The thermal properties for the band of shale in between the two limestones were not measured in situ, but only in the laboratory. Problems were encountered in the evaluation because of unexpected heat conduction on one side of the symmetrically built probe. A modification was made to the previously developed evaluation method together with further testing and correction, before the final results were obtained. As expected, the in situ and lab- oratory measured values of k and alpha compared favorably, since the in situ rock was dry and relatively unstressed.

Jan 1, 1989

By C. O. Brawner

INTRODUCTION My first major involvement on a rock mine slope stability project was in 1966 after I had become a principal of Golder Brawner & Associates in Vancouver, Canada. I received a request from Kennecott to evaluate two serious rock slope failures adjacent to the concentrator on their British Columbia molybdenum property near Alice Arm, BC, which was under construction. A rock slope up to 200 ft* high had been excavated at a design angle of 700. The inspection indicated that several large blocks of about 1000 cu yd each had failed on steeply inclined joint surfaces. Stability was reduced by extensive seepage caused by heavy rainfall. In addition, considerable overbreak had occurred, indicating excessive blasting had been used to excavate the slope. A program was developed to rock bolt potentially unstable blocks that could slide on dipping discontinuities. Some rock was scaled back to the inclined joints, and drain holes were drilled to reduce water pressures. The project was completed successfully and within reasonable economics. As a result of this success, enquiries were received regarding other mining projects. This indicated the potential demand for rock slope engineering. As a result, I took one month off to meet and discuss rock mechanics and slope stability with various people internationally. These included D. Coates in Canada, E. Hoek in England, K. John and L. Mueller in Germany, M. Rocha in Portugal, and the US Bureau of Mines in Denver, CO. Early misconceptions Based on involvement in projects during the next few years, it was concluded that there were a considerable number of misconceptions that existed among some geologists and mining engineers dealing with surface rock mechanics. Some of these included: • Water is a lubricant. This is incorrect. Water reduces the shear strength along discontinuities due to buoyancy, which reduces frictional strength. It also reduces the cohesion of clayey-type rocks. • The optimum pit slope angle in rock is 45°. The optimum slope angle for safety and economics is variable and is influenced particularly by structural geology, water pressures, mine blasting practices, and the depth and degree of weathering. • The flattest angle for slope stability is dictated by the angle of repose of broken rock, about 370. Where clayey-type rocks or clayey infill in discontinuities exists, failure can occur at much flatter angles, requiring flatter slopes or artificial stabilization. • Uniaxial and triaxial tests provide the necessary shear strength parameters to design rock slopes. Most failures in rock slopes are controlled by directional discontinuities. Therefore, the direct shear test is the correct test to evaluate strength parameters for most problems.

Jan 1, 1987

By Juan C. Diaz, Juan P. Carmona, Manuel Z. Salgado, Oscar J. Restrepo

The “Teaching Kids” project is an educational initiative for young people and children from elementary schools. It is carried out by Mining, Geological, and Environmental Engineering students from the SME Student Chapter of the Universidad Nacional de Colombia, Medellin. The primary purpose of the Teaching Kids project is to share knowledge about geosciences and mineral resources in a didactic and attractive way, emphasizing the importance of identifying the use of minerals in daily life and responsible and sustainable mining in our society. Furthermore, this project aims to promote the importance of pursuing geoscience majors in the new generations and improve the mining industry’s public perception. Different methodologies related to early childhood education are implemented, such as gamification, in which the dynamics of games are adapted during the development of workshops to teach and learn in an active and motivated environment. Furthermore, the Montessori Method is used. It implements textbooks, sensory mineral boxes, and presentations to allow learning through experimentation itself (Montessori 2003). The implementation of this methodology has been successful; it has shown high engagement, participation, and retention of the basic concept of geoscience and mining.

Feb 1, 2025

By R. Hogg, T. F. Dumm

Procedures for particle size analysis on respirable dust from coal mines have been evaluated. Using respirable dusts dispersed in a laboratory dust chamber, size distributions measured using cascade impactors have been com- pared with the results of a variety of laboratory sizing methods performed on samples collected on filters placed side-by-side with the impactors. The laboratory techniques included centrifugal sedimentation, laser diffraction/scattering and automatic particle counting. The general agreement among the various methods was very good, with systematic differences which can be attributed to the different definitions of size used. Simple conversion factors have been obtained which can be used to transform the laboratory data to equivalent aerodynamic sizes. Similar comparisons have been made on samples collected in underground coal mines. Again, the results are in quite good agreement although small discrepancies were observed in some cases. These have been attributed to some degree of agglomeration in the airborne dust, leading to slightly coarser apparent distributions in the impactor samples.

Jan 1, 1987

By R. G. McLusky

This paper analyzes the opinion in Bragg v. Robertson, 72 F.Supp. 2d 642 (S.D. W.Va. 1999), a case which threatens the future of surface mining in West Virginia and which will almost certainly result in new policies or rules that will affect surface mining everywhere. This paper addresses: (1) the jurisdictional bases of the action which relies on the federal surface mining laws to enforce a state mining program; (2) settlement agreements reached in the case that threaten to alter federal policies beyond West Virginia borders; (3) a programmatic environmental impact statement on mountaintop mining being undertaken by the federal government; and (4) an opinion by the Court outlawing excess spoil disposal in intermittent and perennial streams.

Jan 1, 2001

By David Green

Outokumpu introduced Flash Flotation in the early l 980's for the recovery of floatable material from grinding circuits. The devel­opment came as a result of surveys made in the company's own concentrators, initiated to find ways of improving recoveries with increasingly complex and lower grade feeds. Hydrocyclones make a separation on the basis of particle size and mass, resulting in the "over collection" of fine grained, high S.G. particles. Minerals such as pentlandite, galena and gold are easily caught in the circulating load around the mill until they are overground and rendered more difficult to collect. In the case of downstream flotation this may simply involve a reduction in the rate coefficient due to the finer sizes or, as is commonly experienced in gold operations, the mate­rial is slimed and coated onto non-floating gangue and is eventual­ly lost to tails. At the time of Outokumpu's plant surveys, it was a relatively common practice, particularly in Pb operations, to have a flotation section fed directly from the secondaiy mill discharge. This is called unit flotation and certainly provided an improvement but very high wear rates and frequent sanding out of the cells was com­mon. The development of the SkimAir® Flash Flotation cell by Outokumpu provided a subtle but quite dramatic departure from the unit cell approach. Now it was possible to feed cyclone under­flow into a special purpose-built flotation machine and recover a final grade concentrate from the grinding circuit (see Figure I). The cell was designed to handle the coarse circulating load, per­mitting the coarsest fractions to be short-circuited back to the mill and retain the floatable sizes for a nominal time of 30 seconds to several minutes. The short retention time was possible largely due to the relatively clean content of the cyclone underflow stream. This means that the fine gangue is not present except in small quan­tities and most of the fine to mid-size paiiicles are higher S.G. and more likely represent valuable mineral. This condition provides for very high rate coefficients. Typical operations would recover 40-60% of the valuable mineral in this fashion and improvements in recovery were typically from 2-5% for sulphide minerals to the 5-20% range for gold and silver.

Jan 1, 1998

By M. K. Gangal, E. D. Dainty

The paper describes the use of portable aerosol monitors in determining real-time concentrations of diesel soot and respirable total dust in dieselized mines. The field studies were conducted in a simulated diesel environment in the laboratory where no other type of dust was present, and in four underground mines with multi-diesel machine operations. Two packages for the real-time monitoring of diesel soot were prepared which included two types of aerosol monitors: a Miniram, model PDM-3, and a Sibata, model PDS-1. These monitors utilize the principle of light-scattering to measure the airborne mass concentration in the environment. The monitoring device results were compared against the Time-Weighted-Average (TWA) values produced by the gravimetric filter sampling method, permitting calibration factors to be determined for each field test. Both instrument packages provided comparable results. The instrument calibration factors varied for different tests, which may be due to different material composition, particle size distribution, density and shape of the aerosols. This approach for real-time determination of diesel soot is found to be simple, inexpensive and easy to use. More field tests for diesel soot determination and further research on size distribution of particulates in dieselized mines are required.

Jan 1, 1989

By Thomas W. Traylor

Today, in Detroit, Michigan, a 14 ft. 6 in. diameter soft ground tunnel is being mined at penetration rates limited only by the logistics of liner handling and spoil removal. Soil conditions are highly variable and include clays ranging from very plastic to very hard, gravels, sands, silts and boulders. The permeable soils contain high concentrations of methane gas, compressed by groundwater levels some 40 ft. above tunnel invert. Despite these adverse conditions, mining crews frequently complete their 70 ft. production quota in six hours and go home. In one 4000 ft. reach of tunnel, progress averaged 68.9 ft. per mining shift. This paper has been written to explain this extraordinary accomplishment, and to demonstrate that truly continuous rapid excavation in difficult grounds is now limited by factors other than the excavation process itself. BACKGROUND The Detroit metropolitan area has a long and interesting history of soft ground tunneling. From 1949 to 1968 the city of Detroit alone constructed some 75 miles of soft ground tunnel. During this period the development and common usage of rotary or "wheel-type" soft ground tunneling machines was pioneered in the Detroit area. These machines are designed for, and were successful in, the cohesive or clayed soils that predominate the downtown Detroit geology.

Jan 1, 1997

By James G. Donovan, Mario G. Karfakis

A large percentage of Southern Appalachian coal reserves are located in seams less than 36" thick. As thicker and currently more mineable deposits are exhausted, methods of underground thin-seam extraction must be developed. Past experience with highwall mining of thin-seam coal has indicated that recovery rates tend to be lower than in conventional operations. It is suspected that this will also apply to underground thin-seam mining, regardless of proposed technology or mining method. Backfilling is one alternative for thin-seam coal mining; although backfill has been used extensively in hard rock mining its use in coal mining has been limited. The ability of backfill to provide additional ground support may enhance coal recovery by allowing for the design of undersized pillars. Backfill is capable of providing additional ground support by restricting lateral deformation of surrounding coal pillars and roof. This additional support can result in significant increases in recovery from thin-seam coal deposits. However, the overall feasibility of backfill is dependent on the in situ behavior of the fill material, the properties of the fill, the effects of the filling method on the total mining operation, and the cost of filling per extra ton of coal recovered.

Jan 1, 2001

By John B. Patton

No academic program of reasonable duration can provide a geologist with all the skills that may be needed for applied work in industrial minerals, but any curriculum that does not provide background in such basic subdisciplines as mineralogy-petrology, stratigraphy, sedimentology, structure, and geomorphology will leave the practitioner handicapped. Enough geochemistry to understand materials requirements, and sufficient geophysics to utilize geophysical data, are essential. In addition to purely scientific considerations, the industrial minerals geologist must be able to evaluate economic factors and may be faced with legal, social, and political problems in land use, zoning, environmental protection, and reclamation.

Jan 1, 1981

By Clayton Vernon Deutsch, Marcel Antônio Arcari Bassani, João Felipe Coimbra Leite Costa, Vanessa Cerqueira Koppe, Pedro Henrique Alves Campos

Traditional linear approaches oversimplify the complexities of ore blending. Adopting nonlinear blending models in mining and mineral processing is critical to enhancing prediction accuracy and allowing optimization regarding nonadditive variables, such as metallurgical recovery. This study implements a simulated annealing algorithm in short-term mine planning that seeks to optimize the metal recovery by considering how to blend the ore in the mine better. Two nonlinear metallurgical recovery models are used as inputs to the algorithm to represent synergistic and antagonistic blending. The results of the case study demonstrate that the optimized schedule exhibits improvements in both blending behaviors when contrasted with conventional linear-based scheduling plans.

Jan 1, 2025

By E. Costa Silva

Among the methods of mineral processing, gravity concentration methods are, probably, those which have lower costs, higher capacities and lower operational complexity. In order to be really effective, these methods require a feed size distribution in which the particles are liberated. Further, there must be a significant difference (usually higher than 1-1.5) among the real densities of the particles. However, in most cases, the traditional gravity concentrators (jigs, shaking tables, spirals and dense medium hydrocyclones) lose efficiency (sharpness of cut and recovery) when the mean diameter of particles are lower than 0.05mm and the difference among densities are smaller than 1. Most gravity concentrators developed in the last 20 years are based on the use of centrifugal forces that create large "apparent gravitational gradient" seeking to overcome the limitations of particles size distribution. This paper presents the experience of the CVRD Research Center in evaluation and development of new process based on using this new generation of gravity concentrators.

Jan 1, 1999