Search Documents

By Kot F. v. Unrug

In spite of extensive research and accumulated experience from mining operations, appropriate coal strength values for pillar design remain debatable. Coal strengths determined in the laboratory on standardized samples vary widely among various coal seams with poor repeatability. Penetrometric in situ strength testing obtains multiple measurements at multiple horizons within the coal seam to provide a strength profile. Alliance Coal has used that method in many of its mines for pillar design. Pillars in these mines perform well. This paper presents a series of case studies and discussion of issues related to coal pillar design. The analysis demonstrates that the proposed default in situ strength of 900 psi is appropriate when no other data exist. However, in the case of appropriate strength measurements combined with analysis of pillar structural composition, differing values can be used successfully. In areas where the penetrometric derived in situ strength is greater than the standard 900 psi in situ strength, reserve recovery has been optimized as required by law without compromising safety.

Jan 1, 2009

By Liming Yuan, A. C. Smith

Barometric pressure changes affect air density, leading to change in the mass of the gas in the gob. When the barometric pressure decreases, the volume of gas in the gob expands, while the volume of gas contracts when the barometric pressure increases, a process which causes the gob to “breathe” out and in. Although the concept of gob “breathing” is simple, its effect on spontaneous heating of coal in the gob area is not clear. In this study, computational fluid dynamic (CFD) simulations were conducted to model the spontaneous heating of coal in the longwall gob area under measured barometric pressure changes. A single longwall panel using a bleederless ventilation system was simulated. If there is no barometric pressure change, the intake airflow rate is equal to the return airflow rate. When the barometric pressure changes, these two airflow rates are no longer equal, and the difference between the two airflow rates represents the airflow rate the gob breathes in and out. The effect of inflow and outflow of gas on the potential spontaneous heating in the gob was investigated using the CFD model developed in our previous study. The effect of barometric pressure changes on the spontaneous heating was found to be dependent on the gob permeability and the coal oxidation rate. The effect of barometric pressure changes on oxygen concentrations in the gob was also examined.

Jan 1, 2010

By J. M. Wempen, M. K. McCarter

"Differential Interferometric Synthetic Aperture Radar (DInSAR) is a satellite-based remote sensing technique capable of measuring centimeter-level surface displacement with high spatial resolution over large areas. Regular monitoring of subsidence due to underground mine development is one potential application of DInSAR, and in this study, the application of DInSAR for subsidence monitoring is evaluated for two mining regions in the mountain west of the United States. In general, DInSAR has potential to identify the shape and extent of subsidence; in some cases, magnitudes and rates of subsidence can be defined. Importantly, the effectiveness of DInSAR for subsidence monitoring depends on the radar band (wavelength), the subsidence rate and the time between image acquisitions, and the topographic and vegetative surface characteristics. INTRODUCTION Differential Interferometric Synthetic Aperture Radar (DInSAR) is a satellite-based remote technique that can be used to measure small surface displacements. Under good conditions, centimeter-level displacements can be measured with subcentimeter accuracy (Buckley, 2000; Massonnet and Feigl, 1998). Additionally, DInSAR data have relatively high spatial and temporal resolutions. Pixels in Synthetic Aperture Radar (SAR) images can have a ground resolution as small as about 3 m, and images often include tens to hundreds of thousands of pixels and cover tens of kilometers. Regions are imaged regularly, and periods between images typically range from weeks to months. In DInSAR, phase measurements from two radar images acquired over the same region at different times are used to precisely measure relative distances (Rosen, 2014). Surface deformation, topography, and changes in the satellite position all contribute to differences in the length of the path that the radar wave travels in each image. SAR sensors use radar with relatively long wavelengths; L-band (24 cm wavelength), C-band (6 cm wavelength), and X-band (3 cm wavelength) radar are used most commonly. Because the wavelengths are long, small changes in the path length of the radar signal can be quantified by measuring the change in the phase of the radar signal between the images. In general, changes in the path length due to changes in the satellite position and topography are known or can be estimated, and centimeter-level changes in the path length due to deformation are measurable. This study evaluates the effectiveness of DInSAR for measuring subsidence in two mining regions in the mountain west of the United States. L-band data from the Advanced Land Observing Satellite (ALOS) and X-band data from the TerraSAR-X mission are evaluated. Imaging characteristics, including the radar band and the time between image acquisitions, are important for effective subsidence monitoring."

Jan 1, 2017

By Yuting Xue, Alper Kirmaci, Taghi Sherizadeh, Dogukan Guner, Khaled Mohamed

Rib brows present a significant safety hazard in underground coal mines in the United States. To address this issue, researchers at the National Institute for Occupational Safety and Health (NIOSH) and Missouri University of Science and Technology (MST) are developing a practical tool to assess both the potential of rib brow formation and the stability of any formed brows. As part of this effort, a monitoring study was conducted to assess the potential for rib brow formation in coal pillar ribs. This study was conducted in a room-and-pillar coal mine where coal pillar ribs are prone to developing rib brows. Although no rib brows formed in the instrumented pillar, data from monitoring and visual observations provided valuable insights into the loading mechanisms impacting the instrumented pillar. These findings helped identify factors that may reduce rib brow formation, including the cavability of the roof in mined areas, the applied rib support, the strength of rock partings, and the overall integrity of the coal seam. The scientific findings published in the case study aid in assessing the potential of brow formation, offering additional evidence for the need to improve rib control methods in underground coal mines.

Feb 1, 2025

By Yuusaku Tominaga

A flexible expert system for a personal computer has been developed to take countermeasures for prevention of emergency in underground coal mines. The system makes a diagram to estimate maximum airflow rate of a specified branch such as coal face or advancing face, etc. under the conditions of opening regulators set in any two different branches, by computer simulation. The system approximates the ventilating condition underground by using both measured values and safety factor derived from the rules in the system. The probability of happening gas explosion, spontaneous combustion and mine fire underground is shown on a display and countermeasures in a data base in the system are selected according to a confidence factor. When it is recognized in the system that either safety factor or confidence factor of countermeasure has a small value, the system sends information relating to reasoning in the system to registered human experts by computer communi¬cation and facsimile. The replies in file transfer from the experts are stored in the system and reconsultations for estimation of underground condition are started automatically. As the replies in facsimile are shown on the display, user inputs new rules and, values for reconsultation. It is shown that the system is available to take better countermeasures as the condition' of a network in coal mine is changed by mining day by day.

Jan 1, 1992

By Susan T. Bagley, Linda D. Gratz, Kirby J. Baumgard

The extensive use of heavy-duty diesel engines in underground mines has raised concerns about the potential adverse health effects to miners exposed to diesel particulate matter (DPM) which contains mutagenic and carcinogenic organic compounds. The purpose of this study was to compare the levels of DPM, biological activity, and polynuclear aromatic hydrocarbons (PAH) attributable to diesel engines in underground coal mines and similar data collected in engine laboratory facilities to assess whether laboratory data could be used to predict in-mine levels of diesel emissions. Mean in-mine DPM and SOF concentrations varied from 0.90 to 1.9 mg/m3 and 0.08 to 0.40 mg/m3, respectively. DPM-associated mutagenicity (mean) levels at two of the mines varied from 400 to 970 revertants/m3. Concentations of three PAH differed by up to four-fold between two of the mines, largely reflecting differences in DPM and SOF levels. The laboratory raw exhaust data were divided by 100 to obtain expected or predicted values for in-mine concentrations. The predicted DPM, SOF, mutagenicity, and PAH values based on laboratory samples were not significantly different from many of the in-mine values. Using a potential in-mine dilution ratio range of 20 to 200:1, virtually all in-mine data fell within the predicted range. Therefore, an estimate of in-mine concentrations can be determined by evaluating laboratory data. This will allow for extrapolations from laboratory tests with particulate emission control devices to assess potential health-related benefits due to their in-mine use.

Jan 1, 1991

By B. M. Kunar, C. S. N. Murthy, B. Rao K

Rock particle size has a very important significance in the mining industry, starting from blasting till the mineral processing. The present study was carried out to understand the particle size distribution in various sieves after conducting the ball milling process. The time of the grinding process was varied at different intervals. It was observed that 80% of the particles of both granite and marble rock samples passed through the 4800 μm sieve when subjected to grinding time of 40 minutes. Also, it was observed the number of particles that were retained in the smallest sieve of <75 μm was higher in the case of granite sample when compared to a marble sample. INTRODUCTION India is a major exporter of granite and marble stones. The major use of marbles and granites are constructing walls and floors. There are several machining processes that are applied before it is used as floors and walls. During this process, wastes are produced these wastes are used in various ways. These include use of powders for clay products (Segadães, Carvalho, & Acchar, 2005), as an additive in cement production (Aruntaş, Gürü, Dayi, & Tekin, 2010), to enhance the properties of brick ceramics (Saboya, Xavier, & Alexandre, 2007), in constructing bricks (Bilgin et al., 2012) and as an additive in concretes (Aliabdo, Abd Elmoaty, & Auda, 2014). Usually, the powder form of marble and granites are used as an additive in the above-mentioned applications. Powders of marble and granite are obtained through the grinding process. One such process of grinding is the ball milling process. In the ball milling process, a quantity of samples along with the charge quantity consisting of steel ball is subjected to a grinding process within a closed chamber as shown in Fig. 1. An even particle size can be obtained through sieving the material after subjecting it to grinding. The present study is planned to understand the particle size distribution in various sieves due to varying time and charge quantity in the experiment. Only time was varied to understand the amount of particle distribution in the case of granite and marble rock samples and a comparison is drawn. A statistical model was developed for marble rock specimen considering the data obtained by varying time and charge quantity in the ball mill experiment.

Jan 1, 2019

By J. A. Haggman

In a country richly endowed in mineral wealth, Climax Arimco Mining Corporation&apos;s (CAMC) Dinkidi porphyry Au?Cu deposit in Nueva Vizcaya province, Philippines, represents the most significant mineral discovery in the country in recent times. The deposit is located within a belt of young intrusive and volcanic rocks in the Sierra Madre mountain chain of north Luzon a region previously unassociated with porphyry-style mineralization. Since 1989, drilling of the Dinkidi deposit has outlined a resource of 124 million tonnes of 1.0 g/t gold and 0.41 % copper. Regional exploration throughout CAMC&apos;s 37,000 hectare FTAA has identified a further sixteen potential porphyry-related deposits. A new mining law was passed in March 1995 but prior to that CAMC had the first Financial and Technical Assistance Agreement (FTAA) granted by the Philippine government allowing 100% foreign ownership of mining projects.

Jan 1, 1997

"Mining of ore bodies that are located at great depths enforces long distances to move the excavated rock masses to the surface. The excavated rock mass contains not only ore that can be economically extracted from the face but also waste, which is usually discarded several steps further downstream in the process. As a result, a large amount of rock is transported to the surface, influencing the costs at which the ore is produced. Reducing the amount of waste rock being transported to the surface by introducing a near-to-face sorting plant would improve the in many cases strained transport system in the deep mine. In this study, one of Boliden’s cut-and-fill mines was analysed with respect to the challenges related to rock transportation and increasing mining depth. The study aims to evaluate the potential use of a new near-to-face sorting system in the operating underground mine. Discrete event simulation was used to study and analyse the rock transportation system with and without the near-to-face sorting plant. The paper shows how the underground rock transportation system and the production were influenced when the near-to-face sorting equipment was added into the current system. INTRODUCTION The locations of waste rejection in the mining processes and the cost of removing waste from the system compared with the cost and energy necessary for further comminution are important parts in the material handling system (Bowman and Bearman, 2014). In an underground mine, longer material transportation distances generate the need for further investment in the mobile fleet and ancillary equipment in order to reduce the waste from the material handling as early as possible. One of the ways of reducing the waste (coarse particle size) in material handling is by use of pre-concentration. The benefits of pre-concentration are well known (Schena et al. 1990; Feasby, 1995; Peters et al. 1999; Klein et al. 2002), as well as the factors governing the feasibility of underground pre-concentration (Peters et al., 1999) and the mining integration issues (Klein et al. 2003). In the Onaping Depth orebody in Sudbury, Ontario the study of implementing the pre-concentration resulted in increased capital costs of 6% and a reduction in the operating costs of between 20-40% (Bamber et al, 2004). In this paper, the effects on the production and the transportation system of implementing underground pre-concentration by means of a near-to-face ore sorting plant in the Kristineberg mine are modeled and analyzed using the AutoMod tool. This tool is based on discrete event simulation (DES) (Banks, 2004), allowing high flexibility in customization and enabling the user to view the production of the system before ore sorting plant integration. The sorting plant selected in the simulation is built from modules. The material is fed by conveyor and goes through the comminution, classification, sorting and service processes after which the waste is redirected to backfill headings via trucks. The system mechanically ejects the particles from the feed stream on the basis of the information obtained from both the XRT sensor’s signal and 3D laser scanner based on both density and rate of refraction of light within a particular mineral. The sorting plant could pre-concentrate the metal ore up to 300 mm size. The plant requires little auxiliary infrastructure, is easily modularized for underground installation and can be easily relocated to different areas."

Jan 1, 2016

By Yong Kang, Renhuan Yu, Xinquan Liu, Liangying Chu, Qian Luo

In grinding-classification circuit, overgrinding, resulted from the fact that hydrophobic materials have higher density than hydrophilicmaterials, has been known as a knotty problem. By using of the air-sparged hydrocyclone (ASH) as classifier, in this pair, the overgrinding of hydrophobic materials has been successfully minimized. Compared with the conventional hydrocyclones, the ASH has less fine hydrophobic particles in the underflow and less large particles in the overflow, which shows that the recovery of fine hydrophobic particles in the overflow has been improved in the ASH.

Jan 1, 1995

The vast coal resources of North Slope, Alaska can be expected to attract substantial interest because the nearly flat lying coal beds of the coastal plan are specially amenable to surface mining. Mining on a scale large enough to justify coal development in this area could have severe environmental effects. The mitigation would be uncertain because large scale coal mining and reclamation operations have not been carried out in the arctic The deficiency of the scientific data base is another factor that requires consideration if coal mining has to develop in accordance with the objectives of PL 95-87. The objective of this paper is to establish the interrelationship between the problems due to permafrost and factors in reclamation of post mining land in order to find ways to transform nature in a rational and purposeful manner and to suggest specific reclamation approaches that may be appropriate in this region.

Jan 1, 1986

By L. Frost

The establishment of a retreat system of longwall mining in this submarine coal field has been under study for many years and, although in special cases there have been limited local applications of this method of mining, there has been no attempt until quite recently to establish a uniform system of longwall retreating&apos; in this area (see Figure 1) Where retreat walls were established, it was strictly as a result of physical, rather than economic conditions. In some of the operations- of the Corporation, where the coal was liable to spontaneous combustion- or the area subject to bumps as in No. 2 Mine of the Cumberland Railway and Coal Company in Springhills the recovery of the coal on a retreat system was more or less a necessity.

Jan 1, 1964

By E. J. Harvey

The Ozarks has been called "a diamond in the rough". In this region streams have steep gradients, sparkling clear flows of cold water fed by many springs, and a wildness that is almost unique in the central part of the United States today. The Current River and its tributary, Jacks Fork, have been set aside for preservation by the National Park Service as a "Wild River" in the first park of its kind in the country. It is called the Ozark National Scenic Riverway. Similarly, responsibility for the preservation of the Eleven Point River has been assigned to the U. S. Forest Service. Protection of other streams in the Ozarks has been considered by State agencies. The hydrologic system of the Ozarks is a complex network of gaining and losing streams, caves, conduits, and large springs. Increased sewage loads derived from the growing towns and expanding tourist trade are a potential hazard; effluents may flow underground for long distances, polluting springs and wells. To add another dimension to the hydrologic picture a new lead industry is also flourishing in the Ozarks. Although the history of lead mining in the area goes back to 1701 (U. S. G. S., p. 43), the area has not seen a revitalization like the one that has been developing in the last 10 years; and the economic growth promises to continue indefinitely. Although this brings capital expenditures and wages into the area, it also brings potential hydrologic problems. Chemicals, wastes and other substances either stored on the surface or transported across it are subject to accidental spillage. In an area where these substances remain on the surface their effects are subject to surveillance. In the Ozarks, however, this may not be possible.

Jan 1, 1970

By S. J. Parkin, P. Shead

Extraction of coal at Harworth Colliery is undertaken in the Deep Soft seam at roughly 1000m depth where the strata temperature is 42 "C. Production employs the longwall retreating method using high powered mechanised methods to extract coal at a rate of approximately 40,000 tonnes per week from a single face. This paper describes the climatic conditions encountered on a typical district , 6&apos;s district, where the initial ventilation set-up was as a typical U-type district which was antitropally ventilated. Under this initial set-up climatic conditions in the intake typically exceeded 30 "C effective whilst in the face area and in the return airway effective temperatures in excess of 32 "C and 33 "C were common . The paper then proceeds to describe the methods employed to attempt to improve the climatic conditions on the district, especially with regard to the coal face and return airways and describes in detail the effects of reversing the district airflow direction, employing homotropal ventilation, on the climatic conditions. The results of this reversal have been dramatic and have resulted in a substantial improvement in the climatic conditions experienced , however problems have been encountered with the control of methane gas since the changeover. The final part of the paper describes the results of computer simulations to analyse the effect of various ventilation designs on the predicted climate for future production districts in order to de- fine a district layout which will produce acceptable climatic conditions in the working zone without the need to use refrigeration techniques and which will improve methane gas control .

Jan 1, 1997

By G. Hoffman

Sustainable development has brought social, environmental and energy efficiency concerns together with management and governance of natural resources. Cement manufacturing, an energy- and natural resource-intensive industry, is adapting to meet sustainable development goals. Emission standards for cement plants and increasing energy costs have lead to changes in the use of natural resources and recycled materials. Utilizing pozzolans or supplementary cementitious materials (SCMs) as mineral admixtures in blended cement or as a substitute for cement in concrete lowers energy costs and CO2 emissions. Although the western U.S. is rich in natural pozzolans, artificial products, particularly fly ash, have greater use as mineral admixtures. Pozzolans and SCMs have many beneficial properties, such as preventing alkali-silica reactivity, a common problem in the western U.S. Barriers exist for mineral admixtures in the cement and concrete industries because of past inconsistencies in quality or availability. New environmental regulations on the primary industries producing artificial mineral admixtures could adversely affect the quality and quantity of these materials in the future.

Jan 1, 2009

By H. Saito

To Japan, which is scarce in natural resources, limestone is the only mineral resource comparatively rich in ore reserves and having broadly recognized outstanding quality. Distribution of the limestone deposits extends from Hokkaido in the north to Kyushu and Okinawa in the south, and the deposits are located in a manner of framework formation of the Islands of Japan. Studies of the geological ages of these ore deposits reveals that almost all of the main ore deposits west of Kanto Area belong to the Carboniferous Period - Permian Period of the Paleozoic Era. Also in the east of Kanto Area, deposits belonging to the Paleozoic Era constitute the main part, although recently there are increasing examples of reclassifying the geological age of the deposits heretofore considered as Paleozoic Era to the Triassic Period of the Mesozoic Era by the recent discoveries of the fossils of conodont, etc. Large ore deposits and main ore deposit groups are given in the Figure 1, which shows that the deposits are roughly found well distributed throughout the country.

Jan 1, 1982

By Saman Khaleghparast, Naj Aziz, Jan Nemcik, Guanyu Yang

"More than 25 years of uninterrupted research on ground support technology for underground mines has been undertaken at the University of Wollongong. This research has resulted in significant findings on tendon characteristics and strength properties. The paper focuses on the development of the fourth generation of cylindrically shaped shear test apparatus for assessing tendon performance in shear. This shear apparatus is known as the MK-IV Double Shear Box or Naj Aziz Double Shear Box (NADSB), and is based on the experience gained from the development of previous versions of rectangular double shear boxes. The new NADSB is circular in shape and is fitted with a truss system, which permits friction free shear testing of tendons across joint planes. A series of double shear tests were carried out on a number of cable bolts commonly used in Australian mines, both plain and indented wires, under varied pretension loads. The results were compared with similar test results using rectangular shaped double shear apparatus, with and without friction across joint faces. The significance of wire surface roughness and increased initial pretension loads are discussed and conclusions made, suggesting that indented wires are inferior in shear compared with plain cable bolts. The general test procedure of the NADSB is described and different concrete reinforcement techniques are reported. The influence of external and internal confinement of the concrete medium blocks in a circular double shear box contributed to consistent test results with a minimum of lateral and axial cracks occurring in the host medium.INTRODUCTIONThe use of long tendon ground support elements (cable bolts) is now a common practice in modern underground coal mines, hard rock mines, tunnels and other underground structures. Due to their material properties cable bolts contribute significantly to the overall ground reinforcement provided by a support system. Cable properties in tension and shear are in many cases vital to maintaining a safe and productive underground environment. Accordingly, tension and shear properties must be assessed accurately using both valid and reliable methods.Load transfer property testing of tendons has been studied over several decades with much of the early research focused on the pull and shear testing of solid rock bolts and hollow bolts (like Swellex and split set tube bolts), as these elements were used extensively at this time. It was not until the 1970’s that the use of cables for ground reinforcement developed, and as such highlighted the need to extend load transfer property testing to include shear strength of cable bolts. Initially, the discarded hoisting ropes were used for ground support in metal mines, particularly in stopping wall support and then late in 1980’s cable tendons began to use in coal mines."

Jan 1, 2019

By I. Iwasaki, T. Fujuita

The removal of phosphorus from steelmaking slags is essential for recycling such slags to blast furnaces for recovery of their manganese, iron, and lime contents. Phosphorus is mainly concentrated in the dicalcium silicate phase of the slags (Fujita and Iwasaki, 1988, 1989; Suito, et al., 1977). Slow-cooling of steelmaking slags in an air atmosphere increased the grain sizes of constituent minerals; however satisfactory magnetic separation results could not be attained because of the close association of a strongly magnetic ferrite phase with dicalcium silicate (Fujita and Iwasaki, 1988). Curie point of the strongly magnetic ferrite phase in the slow- cooled steelmaking slags was investigated and an attempt was made to separate the phosphorus-bearing dicalcium silicate phase in ground slag pulps heated to a temperature exceeding the Curie point. Materials and methods Slag samples, heated to its fusion temperature of 1370°C and slow-cooled in an air atmosphere, were ground dry to -90 µm (about 170mesh) in a ring grinder. The ground sample was pulped to 1% solids in distilled water using 1 kg/t sodium hexametaphosphate as a dispersant and separated in a Sala high gradient magnetic separator, Laboratory Model 10-15- 20B, using a 100-mesh expanded metal matrix and 300 m/h flow rate.

Jan 1, 1990

By C. P. Lazzara, R. W. Pro, A. C. Smith

The U.S. Bureau of Mines conducted a study to evaluate the effectiveness of automatic water sprinkler systems in the extinguishment of incipient conveyor belt fires under ventilated conditions. Large-scale experiments were conducted using a double strand conveyor belt configuration. Standard response, pendent-type sprinklers, with activation temperatures of 100°C, were installed above and between the two strands of belting, in accordance with Federal standards for sprinkler system installations in belt drive areas. Experiments at airflows of 1.1 and 4.6 m/s showed that the sprinklers activated later, the peak heat release rate was larger, and more betting was consumed at the higher airflow. In experiments with 74°C, fast response, directional sprinklers, the sprinklers activated at the same heat release rate for both high and low airflows, but the peak heat release rate and amount of bett consumed was slightly higher at the lower airflow. Experiments were also conducted with 100 °C, standard pendent sprinklers installed above the top belt, in accordance with the National Fire Protection Association (NFPA) Standard 123 for sprinkler system installations in conveyor belt drive areas in underground coal mines. In these experiments, the heat release rate and amount of betting consumed was larger at the higher airflow.

Jan 1, 1995

By Richard E. Ray, George N. Aul, Fred Garcia, William P. Diamond

Increasing longwall panel dimensions, particularly face width in gassy coalbeds, may result in unexpected increases in methane emissions. To investigate this problem, continuous longwall face emission monitoring studies were conducted at two adjacent mines operating in the Pocahontas No. 3 Coalbed, where longwall faces were to be extended from 229 to 305 m (750 to 1,000 ft). It was predicted by regression analysis of methane emissions data from 229 m (750 ft) wide longwall faces that extending faces to 305 m (1,000 ft) would increase methane emission rates by only 7 percent (0.6 m3/min (20 cfm)), to 8.6 m3/min (304 cfm) at the VP-1 Mine. In contrast, it was predicted that extending faces at the VP-3 Mine could increase methane emissions by as much as 13 percent (1.8 m3/min (65 cfm)) to 16.1 m3/min (567 cfm). The geologic and mine design factors in¬fluencing the variation in face emissions between the two mines will be discussed.

Jan 1, 1997