Search Documents

By CLAIRE STREBINGER, ADITYA JUGANDA, JURGEN F. BRUNE, GREGORY E. BOGIN JR.

Methane gas explosions are a major risk in underground coal mining operations. The severity of such explosions can range from local area damage to massive loss of miners’ lives along with significant damage to mine infrastructure and ventilation controls that may lead to mine closure and loss of the entire operation. This study demonstrates the viability of integrating a computational fluid dynamics (CFD) combustion model into a longwall mine ventilation model to simulate methane gas explosions in the longwall face area. The resulting 3D methane gas explosion simulation can provide better understanding of the fundamental physics and the potential impact of an explosion in an underground longwall coal mine.

Aug 1, 2022

By BHAMIDIPATI S. SASTRY, SRIVATSAN J. SRIDHARAN, ANMAYA NAIK, ASIF AHMAD, ADITYA PANDEY

Wet kata cooling power (WKCP) measured using a kata thermometer is a well-known heat stress index in mining industries. Although over the years several researchers have proposed different heat indices and indicated the limitations of the kata thermometer, it is still being used in many areas, especially in the South African gold mining industry, mainly because of its simplicity and rapidity of assessment. This paper presents a comparative analysis of the newly developed empirical expression for WKCP, and some of the more prevalent empirical expressions. The analysis presented based on a regression technique aims to assess the disagreement between model predictions and actual measurements. It is found that the WKCP expresses bioclimatic interaction quite well under the specific parameter of interaction that explains the harsh thermal environment and air condition, such as metabolic activity, the person’s clothing, and the velocity of the air in which the person is working. The statistical analysis shows that the WKCP exhibits significant estimates to thermal stress under lower air velocities, light clothing, and higher metabolic activity rates.

By Dirk van Zvl

The design of cover systems for reclamation schemes in tailings requires estimation or determination of tailings materials properties such as compressibility, shear strength and consolidation characteristics. It is very difficult and expensive to obtain truly undisturbed tailings samples for laboratory testing. In situ testing methods have been developed for economically obtaining large amounts of information. Two of these methods are described, the piezocone and the flat plate dilatometer. Both of these methods provide a rapid means of detailed material identification in a nearly continuous fashion for the entire depth investigated. The equipment is described and typical data from a uranium tailings impoundment is presented. The results are compared and the advantages and disadvantages of these methods are discussed.

Jan 1, 1984

By R. Kramer, A. Habibi

"Diesel Particulate Matter (DPM) measurements were taken at Tronox’s Westvaco Trona mine in Wyoming. Both shift-average and real-time monitoring using Elf pumps and Airtec analyzers, were used. The mine’s underground transportation fleet consists of more than 250 diesel-powered vehicles. A vehicle monitoring log tracked fleet usage during the test; logged data consisted of vehicle type, direction of travel, and time. The log was used in analysis to determine the DPM spread rate, of normally operating equipment, in the different entries with respect to vehicle location. Airflow velocity measurements at the stations were taken during the survey. The survey results also identified vehicles with higher emission rates. An ECOM gas and a MAHA DPM analyzer, both located in the mine’s underground emission shop, were used to obtain various vehicle emission rates. The correlation of the workshop and field measurements was investigated with regard to the machine activity, fuel usage and atmospheric conditions. The results were used to identify and execute a ventilation project to reroute 45% of diesel shop air back to intake entries, by interlocking an automated door and a regulator. The result is reduced DPM downstream. INTRODUCTION DPM has been classified as a potential occupational carcinogen by the National Institute for Occupational Safety and Health (NIOSH).The Mine Safety and Health Administration (MSHA) rule governing DPM exposures in metal and nonmetal mines cites total carbon (TC), a summation of elemental carbon (EC) and organic carbon (OC) obtained by NIOSH Method 5040, as a surrogate for determining DPM exposures (Noll, 2006). MSHA personnel use the 1973 sampling criteria outlined by the American Conference of Government Industrial Hygienists (ACGIH) for collecting compliance-based respirable and inhalation samples in metal/nonmetal mines. Instrumentation developments are allowing improved real time monitoring of ventilation parameters. DPM is within the aerodynamic particle size range of the samplers used for respirable and inhalable dust measurements. If a sampler used by MSHA to collect inhalable or respirable dust samples in underground metal/nonmetal mines was used to collect DPM, both the DPM and mine ore dust would accumulate on the sample filter (Noll, 2006). To comply with the requirement and lower the DPM exposure, mines are implementing a variety of control technologies such as emission based maintenance programs where adjustments or repairs are performed on the vehicles (McGinn, 2000)."

Jan 1, 2016

By K. Pietruszka

The article presents the concept of the application of the Finite Element Method (FEM) and ABAQUS software in the global monitoring of changes in the rock mass and on the surface of the area, as a result of backfilling the workings. Waste materials applied for stabilizing old mining workings can have a strong influence on the rock mass and surface. According to the regulations, this process should be carefully monitored, especially in terms of the safety of surface structures and rock mass stability. The article presents the concept of an analytic and graphic presentation of the results of the measurements of old workings, applying the Finite Element Method and ABAQUS software in model studies. The main purpose of such interpretation of the geodetic observations results is the application of methods providing wide possibilities to present the geometry of workings, their changes and the influence of the rock mass and surface.

Jan 1, 2008

By G. Brofas

Mt Giona situated in the floristic hot-spot of southern-central Greece has an especially rich flora that counts more than 1000 native vascular plant taxa (species and subspecies) and an important plant endemism that is estimated to be about 10% of the native flora. The danger of population reduction of rare and endemic plant species and the opportunity to use rare native species in rehabilitation projects are two different aspects of rehabilitation planning in Mt Giona. In this study, an inventory of rare and endemic species of the area, their classification into IUCN threatened categories and an estimation of their habitats vulnerability are provided. The results emphasize the necessity to develop a monitoring program to analyze population viability of certain threatened plant species. The creation of artificial micro-reserves on calcareous spoils derived from bauxite mining for the conservation of water-stress tolerant rare and endemic plants is also proposed. An inventory of the species that have colonized the mining spoils was also undertaken. Twelve of them are endemics. Seven native species, because of their biological and ecological features, were selected for rehabilitation purposes of disturbed areas by mining activities. Seed germination, aspects of their reproductive biology and seedling emergence after sowing in pots under field conditions were studied. The seed germination study in the laboratory led to the identification of the optimum germination conditions and the creation of germination protocol for each species. Seedling emergence depends on the sowing season and the mulching. The use of the above species is recommended for rehabilitation purposes. The creation of artificial micro-reserves on calcareous spoils derived from bauxite mining for the conservation of water-stress tolerant rare and endemic plants is also proposed.

Jan 1, 2007

By Juan J. Monsalve, AMAN SONI, Nino Ripepi, Richard Bishop

The design and strength of pillars are important parameters when implementing the room-and-pillar mining method in a limestone mine. The process becomes complex with the presence of karst voids, which are frequent phenomena in carbonate rock formations. This research continues a previous study aimed at studying the effect of karst voids on the strength of a particular limestone pillar. Using calculated pillar strength and estimated redistributed stresses, it was assessed that the pillar can counter more stress than currently imparted on it. Numerical modeling studies combining in situ stress determination and excavation sequencing were used to estimate the existing stresses on the pillar. Different possibilities of modification to existing pillar design were simulated using distinct element method (DEM) modeling to determine a better design.

Jun 1, 2023

By J. W. Hawkins, K. B. C. Brady, K. Miller, J. Cuddeback

Remining of abandoned coal mines in Pennsylvania requires the implementation of pollution abatement and mining techniques called Best Management Practices (BMPs). Water-quality data from over 100 remining sites with more than 230 abandoned discharges were analyzed with respect to the types of BMPs employed to abate the pollution loadings of acidity, iron, manganese, aluminum and sulfate. Discharges exhibiting a significant decrease in acidity were most highly associated with sites where large volumes of alkaline materials were encountered (66.7%) or added (63.7%). The best results for iron loading were achieved with large-quantity alkaline addition (54.6%) and water handling systems (47.8%). Water handling systems (47.4%), daylighting (40.7%), and revegetation (40.2%) were associated with significantly lower manganese loadings. The decreases in acidity and sulfate loads associated with increasing the amount of alkaline material in the backfill indicates that the production of acid mine drainage can be retarded by adding large quantities of alkaline materials.

Jan 1, 2002

By G. Delagrammatikas, M. Karmis, J. Mastoris

The evaluation of raw materials in terms of quality profile, mineralogical character and mechanical properties is of great importance to the cement industry. The variability of their chemistry and structure is among the decisive design parameters in the choice of any mining, handling and preblending systems. Furthermore, clinker and cement production require sound estimates of the above parameters, to help produce some appropriate and realistic raw mix configurations and achieve minimum standard deviation of the major components. This paper addresses this subject from the perspective of a cement producer and presents the principles of a methodology aimed at optimizing mine planning and process design. Finally, results from case studies on actual sedimentary deposits currently in operation are discussed.

Jan 1, 2002

By T. Bajpayee, J. Ellenberger

Microseismic monitoring and evaluation is one aspect of the National Institute for Occupational Safety and Health (NIOSH) research program. Roof falls are often preceded by a period of elevated microseismic activity, but not all periods of elevated activity result in a roof fall, nor do all roof falls occur after some amount of elevated activity. The objective of this study is to review periods of elevated microseismic activity and determine whether fracture activity rate can be used to anticipate the initiation of roof falls. The study was carried out at an underground limestone mine where major roof falls are associated with excessive horizontal stress. The progression of roof falls was detected by the microseismic signature produced by the rock falling from the mine roof onto the mine floor, which is termed a roof fall impact event. A total of nine elevated fracture activity periods that resulted in seven major roof falls were examined. It was observed that elevated fracture activity preceded the initial roof fall impact event in three out of four major roof falls. The initial impact event was not identified for the remaining three roof falls. Fracture event rates were analyzed and a roof fall alarm trigger of five fracture events in a ten minute time period was established for this test case. The fall alarm trigger was tested against six of the elevated activity periods. Four roof falls occurred in the six periods of elevated activity, and two would have triggered the alarm before the roof fall occurred, while two false alarms were generated. The results show that limited success would have been achieved by the microseismic system as a roof fall alarm trigger. However, the trigger would have been successful at warning of the onset of elevated activity, allowing mine employees to respond appropriately. The study highlighted some issues with implementing such a system in an operating mine, including the need for real time identification of fracture related microseismic signals among mining induced signals, and accurate location and identification of fracture clustering.

Jan 1, 2007

By Tracy E. Chantson, Brian R. Green, Kenneth G. Ashurst

Work that has culminated in the manufacture and testing of a old-selective resin on a pilot-plant scale is dcscribed. Following a brief discussion about the nature of commercially available resins which identifies them as poor candidates for a gold extraction application, the improved properties of the new type of resin are illustrated using results from comparative loading tests. Further results from continuous countercurrent extractions using synthetic leach liquors and elution work using thiourea as the eluant demonstrate the superiority of the new resin over commercial resins and hence, its potential for use in a resin-in-pulp process for gold.

Jan 1, 1989

By Mo Wanqiang

Equivalent-pressure ventilation is a method of balancing the air pressure between a productive face and its gob to extinguish fires and prevent the infiltration of toxic gases, so that the production of the face can be maintained. The method was successfully applied in Coal Mine No. 1 of Hebi Coal Mining Administration in north-central China. In this article, a practical application of the equivalent-pressure method to prevent carbon monoxide from entering an active longwall face adjacent to a fire breeding area is described, and four steps to achieve equivalent-pressure are discussed. The reliability of using this method and measures to maintain the equivalent-pressure are analyzed. It was observed that this method could maintain high production level while no sacrificing safety at the longwall face.

Jan 1, 1984

By Shailesh K. Patel, Shaaban Ben-Poorat

In order to ascertain the environmental fate of flotation reagents (fatty acids, fuel oils, and amines) associated with phosphate rock processing with confidence, it was necessary to first establish laboratory methodologies to identify and quantify flotation reagents. This approach was necessitated by the fact that the reagents used in the flotation process are either reclaimed or by-products of other industries and is dictated by their cost. Initially, several blind performance evaluation samples were prepared by spiking water samples with known amounts of either single reagents or reagent mixes and then analyzed. Reagent recovery for the blind performance evaluation samples was within acceptable limits for similar compounds established by the US Environmental Protection Agency. Averification process involving the use of standards and the refinement of analytical methods was utilized to develop standard operat- ing procedures (SOPS) and method detection limits (MDLs) specific to the identification and quantification of the flotation reagents used in the phosphate industry. These procedures and MDLs were critical to support the project's primary goal of assessing the fate of selected flotation reagents in the environment.

Jan 1, 1999

By Mark J. Logsdon, Barbara Basse

Mississippi Valley Type Pb-Zn deposits are widespread in the midcontinent U.S. and have been mined from the 1800's to present. Some tens of thousands of acres of mined land in the Tri-State District have been designated as Superfund sites as a result of surficial mine wastes and ground waters with elevated levels of metals. EPA considers the surficial mine wastes to be hazardous and a major source of acid mine drainage fAMD) that degrades water resources and threatens human health and the environment. To mitigate potential risks at one site near Galena, Kansas, a group of mining companies who had been identified by EPA as Potentially Responsible Parties IPRPs) proposed subgrade disposal of the mining wastes in shafts and subsidence features. However, this proposal was challenged by the Agency on grounds related to AMD and the potential for degradation of ground water quality. The PRP team developed a program of materials characterization, laboratory-scale leaching, and finally large-scale, pilot testing in the field. Static and dynamic leaching tests at both laboratory scale fusing artificial rainwater under both variably and fully saturated conditions) and field scale (using pH 4.5 ground water) showed that the surficial wastes do not produce acidic leachate and are not a long-term source of metals. Laboratory chemical and mineralogical tests show that the mine wastes contain substantial carbonate, but very limited iron sulfides, consistent with the leach test results. EPA "characterization" tests fEP Toxicity and TCLP) compare very poorly with tests simulating the expected leaching conditions. While these tests would classify the surficia1 wastes as "hazardous, they do not characterize the behavior of the high-volume, low-concentration, coarse-grained materials with respect to environments and disposal options of interest. To be meaningful, characterization of mining wastes must be performed in a manner that simulates the environmental conditions that are actually of interest with respect to a specific decision, such as subgrade disposal in the saturated zone.

Jan 1, 1991

By Grant R. Brown

The objective of this paper is to describe a study sponsored by the U.S. Department of Energy during which a model was developed to optimize haulback mining procedures in single and multiple seam contour mines, The study objective was to achieve financial- based productivity increases approaching twenty percent. This paper reviews the results of the first year's Phase I activities, which include four main tasks: formulate a methodology that can be used to select equipment and mining procedures that result in optimal performance in a particular haulback mining situation; conduct field studies of representative single and multiple seam mines to obtain quantitative background information for development of the formulated methodology: develop the methodology into a useful design tool for mine operators; and prepare plans for field tests to evaluate the effectiveness of the developed tool.

Jan 1, 1981

By C. Roldan, C. Garcia, J. D. Miller, C. L. Lin

The ultimate recovery in a heap leaching operation is related to the degree of exposure of the valuable minerals in comminuted particles. Recently, high-resolution cone beam x-ray microtomography (XMT) has been used to determine this parameter. XMT technology consists of examining the extent of mineral exposure for each size fraction of ore in 3D, then, by algebraic calculations, the ultimate recovery can be estimated for different particle size distributions (PSD). To confirm the usefulness of the XMT technology for mineral exposure analysis, column tests were performed to determine ultimate recovery using three PSDs for two composites obtained from the copper heap leaching operation at Zaldivar-Chile.

Jan 1, 2003

By S. Helgen, C. Byrns, A. Davis

The 4000 acre historic Robinson Mining District outside Ely, Nevada hosts a continuum of oxidelsulfide waste rock dumps of different ages. In an effort to develop a paradigm to explain past, existing, and future conditions at the site profiles of oxygen, pH, temperature, and specific conductivity were collected from various waste rock dumps using a hand-driven soil gas probe and a down-hole sampling device. The resulting data are useful in interpreting the fate and manner of pyrite oxidation within the dumps and in identifying waste rock dumps that may require remedial measures compared to those that require only minimal action prior to closure.

Jan 1, 2000

By Yoginder P. Chugh, K. V. K. Prasad, R. Missavage

This paper presents results of field monitoring and finite element studies to analyze and improve a room-and-pillar retreat mining system. Fie1 d instrumentation was utilized to monitor pi11ar load changes, roof to floor convergence and differential roof strata movement as retreat mining progressed and to determine in-situ horizontal stresses. A two-dimensional finite element model depicting strata behavior at this mine was developed and used to analyze existing and alternate improved mining geometries. The results showed excellent correlation between fie1 d observed and model predicted behavior. Some of the recommended changes in mining geometry based on the study were incorporated in the mining system.

Jan 1, 1986

By Siegfried Zell

Preface Pipe heading is a customary and proven technology for the underground installation of all types of piping. In over 90 % of all cases, straight pipe sections are used between shaft constructions since, e.g. this follows roadways or it is necessary from the operational aspect due to pipe control methods, e.g. to use a remote control pipe sensor or comparable control devices within sight from shaft to shaft. Frequently, a straight pipeline is impossible, and is replaced by a more or less spatial alignment due to surface conditions, structures in the ground or foundations. This situation applied for the construction of the Nebensammler Neuland (intercepting sewer) in Hamburg-Neuland for sections IV and V. The following paper is not intended as a description of the complete project. It deals mainly with the special features of this pipe heading, with what I believe to be its somewhat unusual route. The task The building authority design issued by the Main Department for Urban Sewerage of the Free and Hanseatic City of Hamburg consisted of the construction of the collector by a pipe heading using NW 1300 pipes in 2 heading sections. One short straight and one long

Jan 1, 1989

By E. Tarshizi

Research was conducted to develop a simulation and animation model for an aggregate (sand and gravel) mine operation. This model can assist the mine engineers to investigate and consider the various options of haulage systems which are critical for the mine operation productivity. Discrete-event system simulation studies can be used for the typical haulage issues that mining engineers are often faced with: using truck fleet haulage, conveyor belts, or a combination of both. The simulation has identified some strengths and weaknesses in the current loading and hauling fleet of the mine, and has resulted in some suggestions for improving the system. The simulation includes animation of the operation. Animation is needed to enhance the benefit of any mine simulation model. By combining the visual power of animation with a mine simulation, a complete picture of the mine system is obtained and displayed. The mine is modeled and animated using GPSS/H® and PROOF Professional®, both of which have shown great applicability in discrete mining simulation projects.

Feb 23, 2014