Search Documents

By Aaron Noble, Mahmud Esad Uluer

Respirable coal mine dust (RCMD) is one of the biggest occupational health hazards for underground coal miners. Dusty mining environments can cause long-term health problems, including pneumoconiosis and progressive massive fibrosis. The Mine Safety and Health Administration (MSHA) has recently revised regulations promoting enhanced dust mitigation technologies, which have sparked renewed interest in the development of dust mitigation technologies. The flooded bed dust scrubber (FBS) is one of the most widely used technologies; however, it is limited by technical challenges, the most notable being the potential to clog. Recent studies have shown that applying vibration to filter mesh can improve the overall efficiency of the scrubber and that the system can be readily integrated to existing continuous mining equipment using an energy harvesting approach. In this follow-up study, the impact of mesh design and surface modification on system efficiency was examined using different vibrating liquid-coated stainless-steel mesh panels in a laboratory-scale FBS. Based on the two-way interaction data from a multi-factor experimental design, the results show that the performance of the system can be optimized by using hydrophilic 20- or 30-layer filters and by excitation frequencies between 67 and 134 Hz. This laboratory study suggests that a 20-layer mesh screen with hydrophilic surface applications and optimized vibration parameters can perform similar to that of a 30-layer static mesh, which is typically used in industrial units.

May 23, 2024

By Fouad Faraj

For every blast pattern, zones of unique material types need to be classified before mining. Most material types can be summarized into different kinds of ore and waste. Blocks generated from blasthole assays are too small to be selectively mined, so areas with a single material classification meeting the mine’s selective mining unit must be defined. Current industry standard practices are to manually draw ore/waste dig limits, but this process is subjective and results in quantities of dilution and ore loss that can be improved upon to enhance the profitability of mining operations. In this study, two weeks of production data from a homogeneous copper (Cu) porphyry and heterogeneous manto-type Cu deposit were used to assess the variability in the hand-drawn dig limits of 20 geologists, mining engineers and ore control specialists, which were compared with the optimal ore/waste delineation. The profit for 20 distinct hand-drawn dig limits for the homogeneous mine varied by 3.7 percent, from $10.5 million to $10.9 million, averaging at $10.8 million. The percentage was nearly double for the more heterogeneous mine at 5.9 percent, from $17.9 million to $19.0 million, averaging at $18.6 million. Using the optimal ore waste delineation, the profit increased to $11.0 million (1.9 percent increase) and $19.3 million (7.0 percent increase) for the homogeneous and heterogeneous deposit, respectively. The natural variability, diggability requirement and selectivity are identified as the main drivers of ore loss and dilution. Recommendations are provided for reducing the subjectivity in manual hand-drawn dig limits by integrating dig limit optimization algorithms as a tool to assist practitioners.

Oct 1, 2024

By Venkata Aneesh

This paper examines the desired blast fragmentation results associated with mining fleet performance at Sidney Quarry of Pike Industries, A CRH Company by reducing cycle times and hauling less oversize material generated from the blast to the crusher to increase the overall plant throughput. We are constrained with blast patterns due to the poorly sorted and fractured seams in the quarry, which is angled at 35° NE and dipping at 80° and runs parallel to the Interstate-95 highway on the east of the quarry boundary about 600 ft, making it challenging to alter the blast patterns for optimal yield. We evaluated multiple relationships between blast patterns in conjunction with loader diggability. Results analyzed include the digging hours, fleet cycle times, and the fragment size with the optimized blast design through 3GSM software to arrive at the optimal yield to maximize the crusher throughput. Our primary objective is to focus on safety with efficient cycle times and clean floors & clean face generation for better operational efficiencies. Secondly, to optimize the crusher yield which is an integral part of quarry operation. Further, this paper provides the utilization of 3GSM blasting techniques in quarry applications with computer vision fragmentation analysis and VizaLogix, a fleet management software to analyze the cycle times sampling.

Feb 1, 2024

By Michael J. Lehnen

Slurry diaphragm walls are commonly used as both temporary excavation support walls, and permanent structural walls, for circular shafts and long rectangular structures (such as underground subway stations); however, they are not commonly used for more compact rectangular or square shafts. In these instances, a second wall is typically cast inside the slurry walls to form the permanent structure. This paper discusses the approach used on the Silicon Valley Rapid Transit Project in California to analyze these compact rectangular types of structures for static and seismic loading, and to determine whether or not slurry walls can be confidently used as both the temporary and permanent walls for two tunnel ventilation shafts.

By V. Miller

C. Hertzler The difference of means of milling characteristics by rock and ore type is tested in a statistical manner in the paper. The null hypothesis being tested is that the sample means of two different populations are equal. It is assumed that the null hypothesis is true when performing the test. Because of this, acceptance of this hypothesis leads to the conclusion that the sample means of the two different populations are equal (or there is no significant difference between the sample means), not that the samples come from the same population, as the author asserts. Rejection of the null hypothesis leads to the conclusion that the sample means of the two different populations are not equal. A P value for this test is reported in Table 2 and is incorrectly identified as the probability that the two samples came from different populations. Actually, what was recorded was 100(1 - p) where p is the usual p-value. The usual p-value measures, on a scale of zero to one, the extent to which the data agree with the null hypothesis. It is the probability of observing a value of the test statistic (Z score) that is at least as contradictory to the null hypothesis as the one computed from the sample data (McClave and Dietrich II, 1982). The author makes no mention of the fact that were these tests to be conducted together, the chances of determining that the null hypothesis is not true when it is really true are increased considerably (Snedecor and Cochran, 1980). This is a multiple comparisons problem and should be dealt with accordingly. The usual methods involve adjusting the level of the individual tests. Table 2 reports an incorrect 100(1 - p) value in the comparison of concentrate grades for other rock types with .30 to .69 % Cu vs other rock types with .70 + % Cu; 86 % should be 98.6 %. Although the article can be criticized for poor data presentation and discussion of that data, the point the author makes regarding the use of these statistics in the ore reserve estimation process is well taken. It does not appear that inaccuracies in the statistical interpretations have hindered that usefulness. References McClave, J.T., and Dietrich, II, F.H., 1982, "Statistics," Dellen Publishing Co., San Francisco and Santa Clara, CA, 766 p. Snedecor, G.W., and Cochran, W.G., 1980, "Statistical Methods," The Iowa State University Press, Ames, IA, 561 p. Reply by V. Miller After reading Ms. Hertzler's comments, it appears that the differences noted were basically semantics. If the paper is ever presented at a math symposium, some changes will be needed. When deciding the best way to present the data to mining engineers and geologists, I decided that presenting the probability that the two sample groupings came from different populations (reverse to the Null hypothesis) was easier and would require less verbage to explain. Hence, the 100(1 - p) difference which was noted. Ideally, I would have preferred to give the recovery and concentrate grades, then comment which ones had significant differences. Unfortunately, Kennecott Corp. did not grant permission to publish the ore body's actual recoveries and concentrate grades. The conclusion is that there was, as expected, a relationship between the ore's geologic properties and the metallurgical properties, and by determining this relationship, the overall mineral model was greatly improved.

Jan 8, 1984

By R. J. Pindred

In his paper, Davis presents an overview of risk. He also introduces the Capital Asset Processing Model (CAPM) as a foundation for selecting the appropriate discount rate for a mining project. While applying portfolio theory is more defensible than the ad hoc adjustment of discount rates, the CAPM is not a panacea.

Jan 1, 1995

By Yasushi Arai

"Among Tokyo Metro’s approximately 200km of subway lines, the Tozai Line that connects Chiba Prefecture and mid-Tokyo experiences congestion of up to 199% at worst and relief of this has become urgent. Therefore, as it is imperative to increase the number of trains operating in the exceptionally congested area from mid-Tokyo going east, a large-scale renovation work is planned between Iidabashi Station and Kudanshita Station that will facilitate turn-back via 3 tracks. While ensuring the safe and stable operation responsible for about 1.35 million passengers daily, this highly difficult work of inner wall demolition and reinforcement of the side walls and floor slabs will only be implemented for 3 hours during late night. This paper discusses large-scale plans to improve turn-back facilities, and the methods of construction therein as an example of operational improvement of a subway network. 1) INTRODUCTION The Tokyo Metro Tozai Line (“Tozai Line”) opened over the entire 30.8 km distance from Nakano to Nishi-funabashi on March 29, 1969. It has the longest operating length of the nine Tokyo Metro lines, and was the first subway line to extend past the borders of the Tokyo Metropolis. Through train services with two other railway companies are available from the Tozai Line. Tozai Line trains join the Sobu Line of the East Japan Railway Company (“JR East”) and the Toyo Rapid Railway Line of Toyo Rapid Railway (“TR”) from Nishi-funabashi Station, and the JR Chuo Line from Nakano Station. The line is structurally distinctive in that 51% of it was built using the open-cut method, 43% of it is elevated and the remaining 6% was built when we used the shield method for the first time 1)2)3)."

Jan 1, 2016

By Joseph L. Petrillo

In July 1997, Kvaerner Environmental signed a unique contract with Echo Bay Alaska called the Transfer Risk and Accelerate Closure (TRAC). The contract called for Kvaerner to assume the responsibilities and obligations associated with closeout of the Alaska-Juneau (A-J) Mine. Kvaerner is an international engineering and construction company with global interdisciplinary experience in the mining industry and environmental remediation. Echo Bay’s requirements called for Kvaerner to: •Provide a fixed price for closure with no change orders. •Negotiate, prepare and implement a final closeout plan as outlined by Echo Bay. •Complete a closure program that exceeded current regulatory requirements. •Improve, expand and maintain a proactive public and community relations program. •Hire Echo Bay employees where possible. •Provide adequate performance guarantees and judicial relief of environmental claims.

Jan 1, 1999

By P. Rambalee

A multiple coal fired boiler house provides steam for utility usage in various production plants. Maintaining stable header pressure and boiler availability is of critical importance for downstream consumers. Advanced Process Control comprising of a G2 based expert system and Model Predictive Control was implemented to improve the boiler house performance. The results yielded improvements in the main header pressure stability, reduction in boiler saturation and significant saving in coal consumption. All information used for this document is from a published whitepaper written and led by Prevlen Rambalee (Anglo Platinum) and Gustaf Gous (BluESP) titled, ?Control and Stabilization of a Multiple Boiler Plant: An APC Approach?.

Jan 1, 2012

By Helmut Hass, Michael S. Shultz

For many tunneling, deep shaft and deep excavation projects ground freezing is one of the best if not the only technique available to create a watertight and load bearing temporary support system in soft ground conditions. When appropriate attention is given to the details of the ground freezing system design, ground freezing is a very safe method and is economically viable with competing techniques and combinations of techniques. Recent innovative uses of the technique in Europe are highlighted in this paper and compared with current uses in North America.

Jan 1, 2005

By Charles W. Axten

Since the mid-1970s, samples of airborne and waterborne fibrous particulates have been collected in the area of the Northshore Taconite Ore Processing Facility by the Minnesota Department of Health (MDH), the Minnesota Pollution Control Agency (PCA), and the University of Minnesota. Indirect sample preparation has consistently been used although other aspects of the sampling methods and sites have varied and analytical procedures were altered over time as more accurate and precise microscopy methods were developed (i.e., phase contrast optical microscopy, transmission electron microscopy, transmission electron microscopy with energy dispersive spectroscopy). In the mid-1970s, levels of airborne fibrous particulate in the Silver Bay area averaged from 0.00030 to 0.03 f/ml. This level was significantly greater than levels of similar particulates in the St. Paul, MN area, although two of the Silver Bay sampling sites, considered individually, did not indicate levels of fibrous particulate markedly different than that seen in St. Paul. More recent sampling data (i.e., 1990?2001) indicate mean concentration of airborne fibrous particulates (amphibole-like fibrous particulates) of 0.0020 f/ml with a range of values from 0.0001 to 0.0140 f/ml. Such levels are not significantly different from those seen in other non-urban environments in the US and Europe. Concentrations of fibrous particulates in water samples were higher in the mid-1970 when iron ore tailings were being deposited in Lake Superior, but since the tailings have been deposited on land waterborne levels of fibrous particulate in the Beaver River have remained relatively constant averaging in the range of 7.5 MFL. This level is only slightly in excess of the current EPA drinking water standard for fibrous particulates. Review and consideration of this data is important in determining the potential health risks associated with airborne and waterborne fibrous particulates in the areas of the Northshore Taconite Ore Processing Facility. © 2007 Elsevier Inc. All rights reserved. Keywords: Taconite; Asbestos; Asbestiform fibers; Fibrous particulates; Cleavage fragments; Phase contrast optical microscopy; Transmission electron microscopy

Jan 1, 2007

By Raymond W. Henn, Kent A. Pease, Glen J. Rorison

The paper focuses on construction of a 2.55-km (8,365-ft) long, 2.4-m (8-ft)diameter storm drain tunnel in Evansville, Indiana. The tunnel was driven through saturated soft ground varying from clay to fine sand. The paper presents: an overview of design and design rational including specific EPB machine requirements; the contractor’s proposed and accepted alternative construction methods and TBM design; and construction issues and performance. Some of the key points discussed are the use of the TBM in different operational modes for alternative ground conditions, the effectiveness of dewatering systems, production rates, and issues such as surface settlements and gas.

Jan 1, 2001

By S. Roy

Soft laminated iron ore (SLO) having a higher hematite content and Martite goethite iron ore (MGO) having a higher goethite content were subjected to detailed characterization and beneficiation. The present research was designed to investigate if these abundant, low-grade ores can be enriched adequately using standard industry techniques. No significant enrichment of the ores using jigging operation on the coarse (-3,200 +595 mm) size fraction could be achieved. Good liberation was only attained in the 150 to 300 mm particle size range in both cases. Desliming enriches the ground ores significantly. The effect of the feed size on the separation efficiencies of the ground ores were studied using flowing-film concentration on a Wilfley table. Better enrichment is obtained in the case of 150-mm sized feed by tabling. The grade of SLO is improved from 56.14% to 66.51% Fe, while the Fe content of MGO is enriched from 55.16% to 65.83%. Substantial rejection of alumina and silica is also achieved. Due to the friable nature of MGO and the higher goethite content in it, the loss of Fe in the form of ultrafines is greater in this case compared to that of SLO.

Jan 1, 2009

By Michael V. Mergentime, Prakash M. Donde

The Nutley Quarry Trunk Sewer Project is a good example of a tunnel that went through difficult and complex ground. The 2 m (7ft.) diameter and 840 m (2,750 ft.)long tunnel passed through soft ground, mixed face, and hard sandstone. The soft ground and mixed face tunneling provided several challenges. During excavation of the tunnel, the Contractor encountered a number of unanticipated large boulders. In addition, the length of the mixed face portion of the tunnel increased by 100%. The Contractor tried various construction techniques to overcome the difficult ground conditions and complete the project. The tunneling progress was slower than expected. The Contractor claimed extra costs for differing site conditions. Through discussions and negotiations between the Contractor, Engineer, and Owner, all of the changed condition claims were settled before the construction of the project was completed. This paper addresses the difficult ground conditions, claims evaluation, and how they were resolved by cooperative efforts between the Contractor and the Owner/Engineer.

Jan 1, 2001

By Steven J. Schatzel, Kayode M. Ajayi, Zoheir Khademian

The integrity of unconventional shale gas well casings positioned in the abutment pillar of a longwall mine could be jeopardized by longwall-induced deformations. Under such scenarios, the surrounding fracture networks could provide pathways for gas flow into the mine creating safety concerns. To provide recommendations for developing guidelines that ensure a safe co-existence of longwall mining and unconventional shale gas production, this study evaluates the impact of parameters that could affect potential shale gas flow into the mine in the event of a casing breach using a discrete fracture network (DFN) model. These parameters are evaluated using a conceptualized DFN realization that is representative of the fractured zone in the overburden, and the range of parameter variations is within values validated with field measurements. The results show that a decrease in fracture aperture (potentially due to longwall-induced stress in the likely vicinity of the breach location) reduces the potential gas flow to the mine by a significantly higher proportion. A 50% decrease in the aperture of the fracture that directly transports the gas from the casing breach location reduces the gas flow to the mine by over 70%. Similarly, changes in the fracture water saturation level significantly affect the gas flow. In all cases, the potential gas flow to the mine is higher if the casing breach occurs at an increased gas well pressure. These findings provide critical information regarding the impact of each of the parameters associated with gas flow in the event of a shale gas casing breach near a longwall mine and could help towards the development of guidelines to ensure a safe coexistence of both industries.

Sep 28, 2022

By M. Ishaq, J. Rosami, J. Brune, E. Sidrow, C. Tsai, S. Slouka

Respirable rock dust poses serious long-term health effects to workers in mining and tunneling underground hard rock environments. When inhaled, respirable silica particles commonly found in quartz and other minerals will scar sensitive lung tissue and cause irreversible lung diseases. Characteristics such as concentration, type of mineral, particle size, and particle shape inhaled can harm workers to various extents. Therefore, this study characterizes rock dust particles less than 100µm in aerodynamic diameter that are released from cutting hard rock in the underground mining environment. In this study, laboratory full scale cutting tests on samples of potash rock were performed with radial picks to generate dust. Three stages of pick wear were tested: new, moderately worn, and severely worn. Comparisons between different stages of pick wear to dust concentration, size distribution, and particle shape characteristics are drawn from this study to start determining the scenarios when the released airborne dusts become potentially most hazardous for workers. Although further testing needs to be conducted to make viable conclusions, the moderately worn pick, or the pick with the most blunt tip, in these experiments are potentially the most dangerous. The blunt pick tip released the highest concentration of dust and generated particle shapes with the highest aspect ratio compared to the other two picks. The preliminary results of this study allow for the further development of optimum bit management and maintenance systems to control the exposure of respirable dust to mine workers.

Mar 2, 2022

By G. B. Johnston

I was very interested in Professor Park's data on subsidence over longwall panels. His paragraph labeled "Conclusion," however, does not seem appropriate for the article. Nothing in the article gives any discussion of how knowledge of subsidence characteristics can be used in mine design to minimize damage. That thought may have been a reason for undertaking this study, but not a conclusion of it. From his article, I would conclude that subsidence movements last considerably longer at great depth. And the National Coal Board's subsidence prediction model represents this area reasonably accurately, though most literature claims their model predicts far greater disturbances than actually occur in most areas of the United States. Also, I would like to know, is the method used to determine angle of draw? The criterion used can make a significant difference in the value obtained. With 30 m (100 ft) spacing and a 122-m (400-ft) depth the angle between stations can be up to 14°.

Jan 1, 1990

By Louis Schaarschmidt, Helmut Mischo, Ibrahim Alsalamin

In order to store high-level radioactive waste underground, the German repository concept considers clay, crystalline and salt formations as suitable host rock materials (National Citizens’ Oversight Committee, 2024). The current research projects of the Chair Underground Mining Methods at TUBAF (Technical University Bergakademie Freiberg) in nuclear waste repositories mainly focus on storage within salt formations. In this scenario, the high-level radioactive waste is supposed to be packed into specifically designed containers and then transported underground and emplaced in horizontal storage drifts. The residual temperature of the radioactive waste leads to the question if there are optimization possibilities for waste handling, the storage and the long-term emplacement of such high temperature level waste. A deeper understanding of the heat transmission from the container into the host rock might lead both towards possibly shorter surface interim storage times as well as size optimization possibilities of the repository itself. TUBAF has conducted research that successfully proved that an optimized container positioning yields more favorable thermal patterns and can be achieved with conventional mining equipment.

Feb 1, 2025

By M. J. Gula, S. S. Xue, E. P. Horwitz, J. T. Harvey

A study has been conducted to control iron in copper electrolyte streams using Eichrom Industries’s new Monophosphonic /sulphonic acid resin. The resin strongly and selectively extracts ferric ion over copper and cobalt from highly acidic copper electrolytes. The resin has a loading capacity of 27 g/L of iron and can be readily regenerated. In addition, the new resin can be easily synthesized using commercially available starting materials. This paper presents the experimental results for iron control in copper electrolyte streams using the new resin and discusses its potential applications to other hydro-metallurgical streams.

Jan 1, 2000

By K. Holmberg, D. Herriot

This paper by Mr Mclvor is yet another contribution to the eternal controversy surrounding the benefits, or otherwise, of high circulating loads in closed circuit grinding. Throughout the paper it is difficult to establish whether the author is referring to effects relating to the mill, classifier, or to the overall circuit. Table 1 is put forward as indicating the advantage of operating at high circulating loads. From the two (it would be interesting to see more) product sizing points provided in each case, the conclusions to be drawn are that cases one and two have very similar size analyses. The third case, however, indicates a much flatter curve, that is to say, higher fines production and a very wide spread of size ranges. If the objective of this circuit is to provide a closely sized product with minimum overground slimes to the downstream process, then it would appear to be the less "efficient" by far. No data is given for product pulp densities either. The term "efficiency" should never be used without a careful and clear definition. In this case, "efficiency" is used to express an apparent percentage reduction in operating work index (Bond) from the measured "standard" at 250% circulat¬ing load operation. The Bond calculation is itself based upon

Jan 1, 1989