Search Documents

By V. L. Franzen, Z. J. Hladysz, C. A. Kliche

The Wharf Resources mine, located in the Bald Mountain Mining District approximately 6.4 km (4miles) west of Lead, South Dakota, has operated a surface gold and silver mine and heap leaching processing facility since 1983. Wharf Resources intends to mine and process gold and silver ore from the Wharf Expansion area which is located on the eastern flank of the currently permitted Foley Ridge Mine. The Trojan Pit for the Wharf Expansion area was initially designed with an overall highwall slope angle of 45o. During mine permit presubmission meetings with personnel from the SD Department of Environment and Natural Resources (SD DENR), the question arose as to whether a detailed slope stability analysis of the proposed Trojan Pit highwalls was completed to justify the 45o slope. Wharf’s response was that the highwall design was based, in part, upon studies completed in1987 on the Annie Creek and Foley Ridge Mines; and, in part, upon subsequent slope stability analyses conducted by Wharf mine personnel through 1996. It was suggested by the SD DENR that the stability study be updated to reflect structural geological conditions in the Wharf Expansion area.

Jan 1, 2000

By Z. J. Hladysz

A Deep Underground Science and Engineering Laboratory (DUSEL) is being planned at the site of the former Homestake Gold Mine in Lead, South Dakota, under the sponsorship of the National Science Foundation (NSF) in cooperation with the Department of Energy (DOE). This national facility will host a variety of multi-disciplinary science and engineering experiments including physics experiments that require shielding from cosmogenic radiation. Current plans include construction of large rooms (up to 55 m in width) at depths of 1.48 km (4850 ft) and 2.25 km (7400 ft) below the surface. Preparation of the preliminary design required the development of a geotechnical characterization program including: preliminary drilling and coring, core logging, drill hole mapping with a televiewer, drift mapping of the geology and rock structure, in-situ stress measurements, and laboratory testing of the mechanical properties of the rocks and discontinuities. Overall rock quality is very good to excellent. Site investigations were followed by geotechnical assessments for the construction of caverns and laboratory modules. The results are favorable and reaffirm selection of the Homestake site for establishment of a Deep Underground Engineering and Science Laboratory.

Jan 1, 2011

By Christopher J. Bise

INTRODUCTION The transportation of men, supplies, and mined material from an underground operation is the connecting link between the mine plant and the surface plant. Unless the mine is accessed by a drift or adit, some form of hoisting system is necessary for slopes or shafts. This chapter will deal with the selection of wire ropes and hoists, two of the most important consider¬ations when designing a hoisting system for an under¬ground mine. WIRE ROPES General A wire rope is designed to transmit forces longitudi¬nally along its axis. Wire rope is used in a variety of mining applications because of its flexibility, high ten¬sile strength, and dependability. Shaft hoisting ropes and principal slope haulage ropes are usually custom-¬built; however, proper rope selection for slushers, car spotters, etc. should not be overlooked. Wire ropes for shafts and slopes, since they represent the life line for the mines, should be of the very highest quality improved plow steel. This quality is necessary to deal with the conditions of loading, winding, vibration, abrasion, and corrosion. Tables I and 2 display the specifications for the typical wire ropes used for mine haulage applications. The 6 x 19-class haulage rope is used for most hoisting where abrasion is not critical. On the other hand, where abrasion is critical, such as a slope application, 6 X 7-class haulage ropes are preferred. For other mining applications, manufactur¬ers' handbooks should be consulted. Selection The selection of a wire rope for a mining situation consists of simply applying appropriate safety factors to a calculated maximum rope pull and comparing the result to the listed breaking strength of the rope under consideration. Table 3 can be used for determin¬ing the minimum factors of safety for wire ropes. To determine the maximum rope pull, the following quantities must be known: the rope weight in pounds (x), the conveyance weight in pounds (y), and the weight in pounds of the load in the conveyance (z). These values are used to calculate the load due to gravity, the load due to conveyance friction, and the load due to rope friction. When these loads are added together, as shown in Eq. 1, the maximum (static) rope pull (RPS) can be derived:

Jan 1, 1986

By D. Lawrence, H. Lawrence, G. Saevil

Plant operators in the mineral processing industry have been implementing expert systems for several years now, with the intent to increase production and reduce costs. Most systems have been installed on grinding circuits of some type and have proven that the technology is viable in that application. However, few applications on other processes have been attempted for various reasons, such as lack of reference sites, complexity of the process, lack of suitable measurements and lack of confidence in the technology. The successful application of an expert system on an Alumina Calcining kiln is the first such application in the West Indies Alumina Company (Windalco), and demonstrates how this technology can be successfully applied to other processes. The key objective of an expert system is to optimize the process. To achieve this the process must first be stabilized, followed by optimization of the operating parameters. The steps taken by this expert system to optimize the process are: • Check for abnormal conditions and deal with them using a prioritized set of special actions. • Use a selection of rule blocks to stabilize the process. • Once the process is stable, achieve additional benefits through further optimization of the process. The potential benefits that a user can expect to achieve through installing an expert system can be assessed on the basis that performance will improve from that of an "average operator" to that of the "best operator" performing at his optimum for 24 hours a day, every day. The quantifiable process benefits include: • Increased production • More consistent product quality • Reduced operating costs • Reduced standard deviation of key variables • Consistent plant operation The success of this project was measured in several ways: project implementation, realised economic benefits, and realised non-economic benefits. With a commitment to maintain the system over the long term, the longevity of the system is assured and will become an important part of the Alumina Calcining control strategy at Windalco. This paper discusses the various phases of implementing the ABB Expert Optimizer expert system, what the benefits were and the procedure that is in place to maintain the system to ensure continued long term success.

Jan 1, 2002

By S. Christiansen, G. R. Winslow, R. W. Kobler

Todays End of Life vehicles are shredded and their metal components recovered and recycled by standard methods. The remaining non-metallic fraction is shredder residue, and contains vast amounts of high value engineering plastics. None are today recovered. Discussed are the developmental approaches used in the first process to recover these valuable plastics. Examined are initial laboratory studies, pilot plant design and construction, product development, results, and flowchart explanations.

Jan 1, 2001

By Y. Nien Wang, Moe Amini, Heiner Sander, Max John

INTRODUCTION As the population increased along the coast route (California Route 1), and the people’s need to have guaranteed access increased, the landslides and related road closures began to have serious adverse economic impacts. Landslides were causing major long-term road closures about every 10 years on average. In 1983, ground movement at Devil’s Slide caused Highway 1 to be closed for an extended period of time which caused significant economic loss to the surrounding coastal communities. A number of options for bypassing the slide area were considered, and the Martini Creek inland bypass was selected for design. Subsequent litigation led to the creation of the Devil’s Slide Tunnel Study in 1996. The results of this study indicated that a tunnel alternative would be competitive with the inland bypass. The final decision was left to the citizens of San Mateo County, who approved the tunnel alternative in the November, 1996 election After completion of environmental studies and the processing of legal challenges, the final environmental document was finished in 2001. The preferred tunnel alternative was designated to proceed for final design and construction. PROJECT DESCRIPTION The Devil’s Slide Tunnels consists of a separated two-lane road, one lane in each direction, which passes through twin tunnels and over twin bridges and then connects with the existing non-separated, two-lane road at each end. The total length of the project is approximately 1900 meters consisting of four main project divisions, which are described below, going from south to north. 1.Operations and Maintenance Center (OMC) area, 2.Southern approach roadways to the South Portals (250 meters), including the South Rock Cut,

Jan 1, 2005

By K. V. Raj, C. A. Berry, A. T. Weakley, A. L. Miller, P. R. Griffiths, D. A. Parks

Diesel particulate matter (DPM) has been classified as a carcinogen to humans by the International Agency for Research on Cancer. As a result of its potential carcinogenic nature, DPM exposure is regulated by the Mine Safety and Health Administration. Currently, diesel emissions in the workplace are monitored by collecting the aerosol onto filters, which are then sent to a laboratory for thermal-optical analysis using the NIOSH method 5040. This process can take days or even weeks, and workers can potentially be exposed to excessive levels of DPM before the problem is identified. Moreover, the delay involved in getting the loaded filter to the lab inevitably means the loss of some of the more volatile organic carbon. To remedy this delay, researchers from the National Institute for Occupational Safety and Health are seeking to develop a field-portable, real-time method for measuring elemental and organic carbons in DPM aerosols. In the current study, the use of mid-infrared spectrometry was investigated. It is believed that mid-infrared spectroscopy is more suitable for use in a real-time field-portable device than thermo-optical analysis methods. This article presents a method for measuring organic carbon (OC) and elemental carbon (EC) in DPM for a broad range of OC/EC ratios. The method has been successfully applied to laboratory-generated and mine samples.

By R. A. Gee, G. B. Ashton, S. T. Warren, P. N. Groves

Northside Storage Tunnel provides 500 megalitres (Ml) (130 million gallons) of storage capacity to capture stormwater/sewage overflows into Sydney Harbour. The6.6 m diameter TBM driven tunnel traverses Middle Harbour 85 m (280 ft) below sea level and through a sandstone/shale rock mass, highly disturbed by stress relief, 20 m(65 ft) beneath the base of the sediment filled palaeochannel. Target limits for inflow, groundwater drawdown and settlement of the valley beaches were achieved by systematic forward grouting from the TBM. Support included rockbolts, sets and shotcrete to carry rock loads, control block instability and spalling and to provide durability and serviceability. This paper describes the tunnelling and grouting works and their effectiveness.

Jan 1, 2001

By M. A. Islam, H. Mischo, G. Barakos

Among the thirty-five declared critical raw materials (CRM) in the United States, there is no sustainable domestic production for the fourteen of them, while for some others domestic supply does not meet the national demand. Numerous potential critical raw material projects are in advanced exploration stages. However, the price uncertainties for many of these commodities put feasible future production into question and come into contrast with overly optimistic price forecasts published in all feasibility studies related to such exploration projects. Thus, in this work, a newly developed smart computational tool is used to evaluate the real perspectives of several CRM exploration projects implementing actual commodity prices, and to conduct reverse calculations in order to find the prices at which each project can be viable.

Mar 2, 2022

I was very interested in Professor Park's data on subsidence over longwall panels. His paragraph labeled "Conclusion," however, does not seem appropriate for the article. Nothing in the article gives any discussion of how knowledge of subsidence characteristics can be used in mine design to minimize damage. That thought may have been a reason for undertaking this study, but not a conclusion of it. From his article, I would conclude that subsidence movements last considerably longer at great depth. And the National Coal Board's subsidence prediction model represents this area reasonably accurately, though most literature claims their model predicts far greater disturbances than actually occur in most areas of the United States. Also, I would like to know, is the method used to determine angle of draw? The criterion used can make a significant difference in the value obtained. With 30 m (100 ft) spacing and a 122-m (400-ft) depth the angle between stations can be up to 14°.

Jan 1, 1989

By D. Leppert

Mr. Garrett brings up several interesting points with respect to the proposed API specification for "nontreated bentonite." However, although not explicitly stated, these specifications are being written based strictly on bentonites from the Wyoming/South Dakota area. Other sodium bentonites may be suitable for use as drill mud but will be unacceptable since the specifications are designed for Wyoming bentonites. Regardless of the API's intent that its specifications are intended only as guidelines, they are generally adhered to on an international basis and, for practical purposes, might as well be chiseled in stone. Estes (1986) notes that the quality of bentonite available from Wyoming producers has steadily declined since the early 1960's. The plastic viscosity: yield point (PV:YP) ratio was included in the current API 13A specification primarily to prevent excessive polymer treatment of lower quality bentonites to make drill mud. However, with development of polymers designed to control YP, this specification cannot ensure that only high-quality bentonites are used for drill mud. Nor will the new specifications for untreated bentonites. Other sodium bentonites are available. Bentonite produced in southeast Oregon demonstrates superior performance characteristics without addition of polymer or other chemicals. However, the exceptionally high purity of these deposits leads to a relatively high YP:PV ratio since the naturally high YP probably results from the higher purity and smaller particle size of this bentonite (Rath, 1986 and personal communication). These bentonites typically have a smectite component exceeding 90% (Rath, 1985), compared with 70% to 75% smectite for typical Wyoming bentonites, as determined by X¬ray diffraction and tests for colloid content. As evident from the accompanying table, the untreated Oregon bentonite has excellent rheological properties, though different from Wyoming bentonites due to the high purity. Additionally, this bentonite reacts well with polymers typically used in the oil industry, making it eminently suitable for use in a low-solids mud system. The extremely low grit content, less that 0.5% on a 75 mm (200-mesh) wet sieve, greatly exceeds the standards set for Wyoming bentonite. Optimum rheological properties are obtained at a higher moisture content than Wyoming bentonites. At 10% moisture, API 13A maximum, the clay is overdried, again reflecting the high smectite content. In summary, the specifications proposed by the API Task Group will ensure that only Wyoming producers can supply "nontreated" bentonite to the oilfield since specifications are

Jan 1, 1989

By Aditya Rana, A. K. Mishra, M. M. Singh, N. K. Bhagat

Many cases of derailments, train accidents and traffic interruptions due to the slope failure and rockfall have been reported in the past on Konkan Railway trackline because of unstable rock slopes. The authorities installed stability enhancement measures such as wire netting, rock bolting and shotcreting which were found insufficient. The failed geotechnical measures prompted authorities to excavate the unstable slopes. Rock blasting is generally not preferred for the excavation of slopes along the transportation route. Stabilisation and widening of slopes by blasting need closure of the route for a considerable time. Discontinuing traffic on Konkan Railway route was undesirable as it connects two important port cities Mumbai and Mangalore. The paper presents an innovative directional controlled blasting (DCB) technique for excavating three unstable slopes (i.e. cuttings) in hilly terrain without disturbing the traffic. New empirical formulae for small geometry blasting to estimate burden and throw have been developed. A unique sequence of firing and excavation with powder factor varying between 0.04 and 0.39 kg/m3 irrespective of the actual free face was used for rock blasting. The process controlled the throw of blasted material over the track and resulted in a smooth and stable wall. The slope angle has been changed from 80 to 82° to 45–47° and probability of wedge, planar and toppling failures was eliminated. About 100 such accident-prone slopes (52 km cumulative length, 7% of total route) situated at discrete locations along Konkan Railway route were stabilised using the technique. No incident of rockfall and slope failures along these slopes has been observed after the stabilisation.

By Roland W. Rammler

In recent years, the crude oil reserves of the world have increased at the same rate as the consumption. A Consideration of the global figures suggests that adequate supplies of petroleum will be available during the next decades. On the other hand, it in a fast of economic and political significance that the reserves in the industrialized countries increase much more slowly than in the developing countries. In Western Europe the reserves have even decreased. At the present time, about 70 % of the petroleum reserves of the world are in the Middle East and in Africa in regions in which political arises are prevalent or impending. For the industrialized countries, the discrepancies between the consumption and reserves in various regions of the world are a strong urge to investigate whether oil can be recovered from other sources. The situation will probably not be changed to a large extent by the discovery of oil in the north of Alaska. The main starting materials for the production of synthetic crude oil are coal, oil shale and tar sand. In North America, where the consumption of petroleum increases more rapidly than the reserves, there are enormous deposits of each of the three materials. This fact is another incentive toward the utilization of these unconventional oil reserves, which provide a reliable basis for a supple of energy for a long time to come.

Jan 1, 1970

By M. Albrecht

I have been following the discussions on coal degradation started by the article "Degradation process in coal slurry pipe-lines," by M.G. Ayat and B.C. Scott. I agree with Mr. Dasher's comments in January that the title of the article was perhaps misleading as the information appeared to pertain more to processing the coal than to transportation. Specifically, the authors' conclude that the cyclone had an important impact on the degradation. Dr. Ferri's comments on degradation in other physical processes was very correct, handling of coal in a turbulent manner has an impact on the size distribution of the coal. This is one reason that when I design a coal system (mine to rail car) I try to minimize the total number of transfer and processing steps consistent with achieving the desired product specifications. Another area, mentioned in passing in the article, the impact of natural causes and the mining step, is of particular interest to me. A mine in West Virginia had a variation of 50% in the -6.35 mm (-0.25 in.) raw coal depending upon the direction of mining. Since it was a single unit mine, this significantly impacted the final product. Two articles on mining's impact on size distribution are: • Stefanko, R., Chopra, 1K., and Ramani, R.V., 1974, "Mining influence on size consistency and washability characteristics of coal," SME Fall Meeting, September; and • Albrecht, M., and Olsen, D., 1980, "Mining methods impact on coal preparation plant design," 1st International Mine Planning and Development Symposium, September. Both articles presented information on variation of size distribution and cleaning plant performance on a coal depending on the mining method used. Both articles considered a single coal seam at one mining operation. Stefanko's article considered continuous and conventional mining of coal in Pennsylvania. Albrecht's article considered surface, underground continuous, and underground hydraulic mining of a coal in British Columbia. Both concluded that mining methods do impact coal characteristics. I agree with Mr. Ayat's comments in reply to Dr. Ferri's discussion, "... degradation is a multi-faceted phenomenon involving many natural and man-made factors." As efforts are being made to produce a higher quality (lower sulfur) coal, this topic becomes even more important

Jan 1, 1989

By Ali Ekrem Aritan

Exposure to hand-arm vibration (HAV) among the labor force in the mining industry can result in permanent vibration diseases such as behavioral disorders, visual impairment, osteoporosis, pain (mostly in the hands, wrists, and shoulders), circulatory system disorders, and malnutrition. In this study, the vibration exposure of excavator operators working regularly in 25 different natural stone quarries was measured. In addition, the relationship between vibration exposure and rock properties was investigated. Gloved and ungloved vibration measurements were performed and revealed that antivibration gloves reduce excavator operators’ vibration exposure by 7.10–25.95%. Samples from each quarry were characterized with rock mechanics tests. The correlations between the hand-arm vibration measurements and the natural stone physical–mechanical properties (uniaxial compressive strength, Shore hardness, Knoop hardness, apparent density and total porosity) were determined to be over 70%. One finding of the study was that the health risk in excavators cannot be reduced sufficiently by the sole use of antivibration gloves. Furthermore, the excavation of any rock with a Knoop hardness above 121 is associated with an 81% risk of HAV. To increase awareness of the danger of vibration exposure for natural stone miners, training programs should be provided, and technical and operational changes should be implemented.

By Katzer R. Klimpel, J. Sewell

Dr. Roussey Roussev The use of chemical additives on grinding is of significant importance considering the high energy consumption of grinding processes. My research indicates that the dispersant approach explains the effects, in this particular case of wet grinding. Further, the dispersant approach combined with torque measurements give the possibility of clarifying the mechanisms involved when using grinding aids. I find the conclusions derived from the data obtained to be correct and useful for grinding. In general, I agree with the explanations. However, I would like to discuss several additional points that I consider to be important, and in the same time to mention some of my own results from investigations similar to those presented in the study under discussion. The "bed volume concept" and the change of slurry viscosity explain adequately the data plotted on fig. 3, in conjunction with Figs. 1 and 2. However, the significant increase of the average torque in the case of 83% solid with XFS-4272 introduces the necessity of establishing the optimum of percent solid when dispersant is used. For example, the optimum percent of solid for different materials varies. One of the reasons is the material's mass density. On the other hand, it is necessary to determine the concentration of the chemical used. Because of this, it would be interesting to know how the cited concentration was selected. The supportive discussion and verification by Dr. Roussev, with results similar to that of the paper, is appreciated. I will try to answer the additional questions he has raised. To begin with, the mill was fitted with six lifters of approximately one-quarter inch height. There has been extensive lab and plant level work to understand downstream influences of using dispersants like XFS-4272*. In sulfide ore processing, which is the area in which most industrial scale testing has been performed with this approach, neutral to positive influences have been observed. For example, positive effects (e.g., increased recovery) have been noticed in flotation operations involving ores that have a tendency to produce excessive slimes upon grinding. (1) Also, the use of a dispersant has been shown to demonstrate a positive influence on classification by improving the sharpness of separation and preventing a decrease in d50 value that usually accompanies increasing flow rates to classifiers.(2) The biggest potential downstream problem is in thickening, which at the dosages involved, has not been a problem in plant scale usage. The commercial price of dispersants like XFS-4272 is quite variable depending on source, concentration, etc, but a typical cost of XFS-4272 to achieve a 10% increase in throughput in industrial mills has been between 20 and 35- US per ton of feed ore (1981).

Jan 12, 1982

By R. D. Hagni

Introduction The ore deposits of the Viburnum Trend in the Southeast Missouri Lead District constitute the world's largest lead producing district. Six or seven mines currently are in production in the Viburnum Trend. The principal minerals are few in number, simple in composition, and form simple superposition and replacement textures. The economically valuable minerals in the typical lead-zinc ores of the Viburnum Trend are the sulfides, galena, sphalerite, chalcopyrite, and siegenite. The most abundant gangue minerals are dolomite, marcasite, pyrite, calcite, quartz, and dickite. Four concentrates, lead, zinc, copper, and cobalt are produced from the ores, and they contain an interesting suite of trace elements, of which silver and cadmium are recovered at the smelter and refinery.1 Emphasis is given here to the variations in directions of ore fluid flow based upon interpretations of the positions of orebodies due to the ore fluids being impeded by Precambrian basement relief and upon patterns of ore mineral/metal zoning. The Precambrian basement relief and Lamotte Formation pinchout has exerted an important control upon the specific locations of orebodies in the Southeast Missouri Lead District. The locations of some orebodies along one side of Precambrian knobs or ridges strongly suggests that they are positioned on the side from which the ore fluids flowed. Other orebodies are located in positions that suggest that they formed where the ore fluids passed around or between Precambrian knobs. Patterns of mineral and/or metal zoning have been used in many mineral districts to interpret the directions of ore fluid flow. The mineral/metal zoning pattern correlates closely with that of the mineral paragenesis. The earliest deposited minerals tend to be deposited nearest to the source, the later deposited minerals next closest to the source, and the latest deposited minerals furthest from the source. In the Southeast Missouri Lead District, it is interpreted here that the early-deposited copper-rich ores are closest to the source of the ore fluids, the subsequently-deposited zinc-rich ores are next closest to the source, and iron-rich ores are furthest from the source.

Jan 1, 2006

By Karen Bolm, Floyd Gray, Ailiang Gu, Kerry Caruthers, Carlos Velez, Laurie Wirt, Douglas M. Hirschberg

Understanding sources of dissolved metals and transport characteristics of acid drainage is needed to assist land-use strategies in mineralized regions, particularly in the semi-arid southwestern United States. Water- quality samples were collected from mined and un-mined parts of the Patagonia and southern Santa Rita Mountains of southern Arizona from streams, springs, seeps, adits, alluvial wells, and bedrock wells. Water quality during base-flow conditions was compared with that *of runoff samples from infrequent winter and summer storms. The largest fraction of annual discharge in these ephemeral streams consists of storm runoff, although springs provide a steady source of low discharge base flow to numerous intermittent perennial reaches. Several abandoned mines in the northern Patagonia Mountains contribute acid and heavy metals to streams. During base-flow conditions in mineralized areas, natural springs and intermittent stream reaches produce acidity but the volume is typically low and acidity is often diluted or neutralized down gradient. Overland runoff contains low concentrations of dissolved metals and moderate acidity, however, stream waters were strongly acidified and metal-laden from contact with abundant pyrite-bearing stream sediments derived from erosion of waste-rock material in and along the sides of the stream channel.

Jan 1, 2000

By J. H. Tu

The technical paper correctly points out that the kriging variance is not a good measure of the uncertainty of the estimated (i.e., kriged) value of individual blocks. The au thors claim that their proposed jackknife method, which is a rekriging of each block by eliminating, in turn, one sample from the original sample set and then taking the average of the rekriged estimates, not only gives good block estimates, but the resulting jackknife kriging standard deviation is a useful indicator of the "true uncertainty associated with block estimates." However, they immediately abandon the idea of using the block-by-block standard deviations, reasoning that these standard deviations are not independent and that there is no easy way to utilize them. There may be another reason for not using them. The jackknife standard deviations for individual blocks given in their example are mostly in the range of 0.004 to 0.005 oz/st (0.14 to 0.17 g/t) with only one block having a high value of 0.012 oz/st (0.41 g/ t). These individual block standard deviations are as low as the jackknife standard deviation for the mean grade of the entire shape, i.e., 0.0041 oz/st (0.14 g/t). Do they represent the "true uncertainty" of the individual block estimates? Could the authors explain this? In a global shape consisting of a large number of blocks, any given sample will affect the kriged estimate of only those few blocks within its vicinity. This is the rationale for the authors' selective rekriging, making the jackknife algorithm more efficient. On second thought, why not do away with jackknifing altogether? Just cumulate and normalize, if necessary, the kriging weights of each sample used during the ordinary block kriging process, and then compute the global variance from these kriging weights and their respective sample grades? After all, isn't the global mean grade nothing but the weighted average of the samples used in the estimation? Reply by G.S. Adisoma and M.G. Hester The jackknife is one of the many tools in a practitioner's toolbox to solve estimation problems. The strengths of the technique lies in its simplicity, i.e., it uses the concept of mean and standard deviation and the fact that it can be easily combined with other tools, in this case kriging. Because the jackknife kriging (JK) estimate is also the mean of the pseudovalues, the JK standard deviation is attractive just as the standard deviation of the mean explains the variability of the data. The difference is that the pseudovalue calculation in jackknife kriging uses the ordinary kriging (OK) weighting scheme instead of simple arithmetic averaging. The data used to illustrate the jackknife technique in the paper consist of high values that are roughly three times the low values. The resulting JK estimate of the block grades show that the highest estimate is roughly twice the grade of the lowest estimate. The contrast between the low and the high estimate is more evident in the JK estimate than in the OK estimate, even though the mean grades of the blocks for the two estimates are very similar. Nonetheless, in this paper, we are concentrating more on the need for a more realistic measure of uncertainty, or precision, for the estimate. Unlike its OK counterpart, the JK standard deviation of the blocks clearly reflects the original data variation. The highest JK standard deviation of the blocks is three times its lowest value. This follows our intuition that, when the samples used to estimate a block is more variable, the resulting estimation variance (or standard deviation) should be higher than the case where the samples are more uniformly valued. However, block-by-block standard deviation or variance is of little practical value in reserve estimation and classification, as well as in mine planning. One is usually more interested in quantifying not the variance of the individual block estimate, but the uncertainties associated with a much larger dimension, such as the minable reserve. Thus, the thrust of the paper is to find a simple way to obtain a single estimation variance or standard deviation associated with the reserve grade estimate. The discussion by J.H. Tu did not mention how one would obtain the global variance from the OK weights and the sample grades. As a technique that offers a data valuebased measure of uncertainty for its estimate, the "leave-one-out" jackknife fills this need nicely through the block kriging shortcut approach described in the paper. Note: The first column and the last two columns of Table 3 in the paper should have contained a single number each, namely, an OK estimate of 0.0317, a JK estimate of 0.0333 and a JK standard deviation of 0.0041 oz/st, respectively, for the shape, as are obvious from the text. ?

Jan 1, 1998

By Rihab Guellala

In Tunisia, the Paleocene-Eocene series has an important socio-economic interest. It contains profitable oil and water accumulations. Moreover, it encompasses phosphate reserves. The present study uses seismic reflection prospection and borehole data for the reconstitution of the Paleocene-Eocene deposit structure in the Jerid area (southwestern Tunisia), a crucial step for the phosphate exploitation. Firstly, lithostratigraphic correlations incorporating water and petroleum wells were established according to different directions for a tentative approximation of the Paleocene- Eocene deposit geometry by following their lateral evolution. To give more details, seismic reflection profiles were interpreted in the second step. The Paleocene-Eocene formations were associated with their corresponding reflectors on the closest seismic profile using the relation of time and depth in petroleum wells. Analysis of lithostratigraphic correlations shows notable variations in the Paleocene-Eocene series thickness and depth. Seismic profile interpretation explains these variations by highlighting different buried tectonic features. The results confrontation reveals that the phosphatic deposit geometry in the Jerid area is mainly influenced by the (1) emergence of the Saharan platform and the Chott northern chain since the Late Cretaceous, (2) syn-sedimentary normal activity of E-W and NE-SW faults during the Paleocene-Eocene epoch, (3) reverse-reactivation of these faults, and (4) major Tortonian folding phase. This study can enormously enhance the Jerid area socio-economic development by presenting useful findings that may orientate the phosphate exploration.

Aug 15, 2021