Search Documents

By Patrick J. Doig

The Lewis Street CSO Tunnel is an important element in the efforts of the Metropolitan Government of Nashville and Davidson County (Metro) to improve the treatment of waste-water in the area. The tunnel is approximately 1,675m (5,500ft) long with a finished diameter of 2,600mm(102inches). 116m (380ft) of tunnel was constructed in soil with the balance being in lime-stone rock. Excavation was with a 3,700 mm (12ft) diameter Jarva hydraulic shield in soil and a Jarva Mark 12 TBM in rock. The permanent lining of the tunnel comprised concrete pipe with steel end-rings and a vinyl liner. This paper describes the construction of the project with particular emphasis on the excavation and lining of the tunnel.

Jan 1, 1997

By Kazuo Magata, Hirohiko Fujita, Masazumi Tashiro, Yoshiaki Sato, Yoshio Shinoda

The Shinkansen of the Japanese National Railways (JNR) presently in operation between Tokyo and Hakata, approximately 1,000 km, was constructed at three stages: between Tokyo and Shin-Osaka opening in 1964, Shin-Osaka and Okayama in 1972 and Okayama and Hakata in 1975. Works on the extension of 400 km from Okayama to Hakata were launched in March 1970. As construction of the undersea Shin-Kanmon Tunnel on the extension was the toughest task, requiring many, many months, the work was undertaken earlier than any other works on the extension. It was brought to its completion in June 1974 at the cost of about 22, 000 million yen. The Shin-Kanmon Tunnel is the third undersea tunnel constructed to connect the main island of Honshu and Kyushu across the Kanmon Straits. (Table 1)

Jan 1, 1976

Coal that meets customer specifications is often stored in silos prior to being loaded into railcars. However, it is often found that, after loading, the coal contained in a particular car does not meet customer specifications. This can occur because of the variability inherent in the coal and because of segregation, mixing and flow inside the silo. Some contracts now require the coal in each car to be within specification. Silo flow models are used to predict quality in such cases. However, developing an accurate silo flow model for each case is difficult and time consuming. This paper examines the viability of using an online analyzer in conjunction with a feedback circuit to optimize the quality of the coal being loaded into trains, so that each car meets the quality specifications.

Jan 1, 2002

By Andrew W. Jenike

The first significant studies of problems related to the handling and storage of bulk solids were reported at the end of the nineteenth century. Early work originated from the necessity to store large quantities of grain and was concerned mainly with pressures affecting the structural design of silos and bins. The Janssen formula (about 1898) and the work of Ketchum [1] form the highlights of that period. In more recent years, progress in mechanization, increasing plant capacities, and rising costs of labor have focused the attention of engineers on the problem of gravity flow of bulk solids. A great deal of work has been done with models, and flow patterns obtained in small scale bins have been described in several publications, for example [2, 3]. An attempt to develop a theory of flow of bulk solids was reported in 1954 [4, 5, 61 and presented to the in a paper [7] in the same year. AIME recommended the continuation of this work and, as a result, Engineering Foundation granted a sum of money to set up a Bulk Solids Flow Laboratory. Two and a half years ago the project gained the support of the University of Utah and a laboratory was set up on the campus of the University. This project is now in progress, it has received the support of the American Iron and Steel Institute and of Kaiser Engineers, Division of Henry J. Kaiser Company. The results obtained to date are summarized in this report.

Jan 1, 1959

By Stephen Semeniuk

Working with junior mining companies as a valuer, my experience with regulators is that simplicity works and the sales comparison method is the way to go. What I like about Mr. Ellis?s approach (as in his Table 7) is the integration of commodity prices with the timing of acquisitions and the implication of price changes in gold on the adjustment of individual project valuations. However, the sample gold-related appraisals in Ellis?s paper are pre-2008 transactions and readers should be made aware of the current market for such projects. Before moving on, to be noted is that the effective date of the Las Brisas appraisal (Ellis?s sample Appraisal 3) is Feb. 10, 2006; given that the subject value of Transaction 9, Choco 10 in Ellis?s Table 6 was listed as $353 million for a 95% interest in the con-cession, I am uncomfortable accepting that the acquisition was suddenly worth the adjusted value of $1,205 million (as given in Ellis?s Table 7). In some cases, illiquidity discounts can apply, and commodity-wise, in the one-month period between the acquisition in January 2006 and the adjustment to the Las Brisas conditions as of February 10, 2006, the indicated gold price change was only 41 cents/g ($12.60/oz); i.e., from $17.50/g to $17.91/g ($544.40/oz to $557/oz).

Jan 1, 2012

By L. B. Hales

Image analysis for feed belts and flotation has been used for over 20 years. It has been shown to aid in the modelling and optimization of Sag Mill circuits, and any improvements in the image analysis result in improvements in the model for control. Using a laser to measure the height-profile of rocks on the conveyor has been shown to increase the accuracy of the size classification. We have developed a system using two cameras in a stereoscopic configuration to provide height-profile measurement without the added expense and safety concerns of using a laser. Additionally, we have developed a novel technique for calibration of the system, using artificial intelligence techniques to optimize the model fit by adjusting the image analysis tuning parameters to values resulting in the best classification.

Feb 27, 2013

At the 25th Peruvian Mining Convention, the start-up of Antamina was called ?the mining event of the year.? Antamina, one of the largestcopper-zinc mines in the world, began operations in May 2001.Augusto Baertl is Executive Chairman of Compañía Minera Antamina, the operating company. He said in a convention address that Antamina would be in full production in 2002. ?I would like to stress that Antamina is, in every respect, a highly stringent operation, as it intends to be the Peruvianmine of the future,? Baertl said. ?Antamina has set the target of being, and remaining throughout time, a model mine as to technology, environmental practices and social responsibility.? [ ] In the areas of technology and operations, Baertl noted that ?we have incorporated the best engineering design available and state-of-the art technology for mining, grinding and transportation processes, among others.? In the environmental area, he said that ?we have carried out careful environ-mental impact studies and have incorporated modern technologies and methods to control and minimize any environmental impact.? In the social field, Baertl noted that ?our relationship with neighboring communities is being developed under the premises of the social responsibility philosophy.? These include popular consultation processes, environmental committees and conciliation discussion committees. The purpose, he said, is to encourage communities located within the area of influence of the project to find and lead by themselves their path toward sustainable development, beyond the life of the operation itself.?

Jan 1, 2001

By Simon Hille, Rein Raudsepp

Since 1991, the Porgera Joint Venture has processed refractory sulphide flotation concentrate by pressure oxidation with subse­quent gold recovery from the washed residue, by a conventional leach/carbon-in-pulp (CIP) circuit. The capacity of the plant has been progressively increased in five stages of development. In December 1995, a third oxygen plant was commissioned, raising the total oxygen production to 750 t/d and thus allowing for an increase in the oxidation capacity of the four autoclaves. The daily sulphur oxidation rate in 1995 was 192 t/d with 99.5% oxidation, as compared to 293 t/d in 1996 with 99.0% oxidation. This paper details the performance of the pressure oxidation circuit through 1995 and 1996, and compares measured plant parameters with the original Sherritt (now Dynatec) process design criteria.

Jan 1, 1998

By H. G. Linge

The Australian gold industry currently contributes some $4bpa to the national economy [l]. Some 40% of the total gold is produced in the region centred on Kalgoorlie known as the Eastern Goldfields of Western Australia. This region is the largest single centre of production with an output of some 100 tpa of gold [2]. In the Eastern Goldfields, refractory arseno­pyritic gold ore is an increasingly significant source of gold, feeding several operations utilizing bio-oxidation as the pre­carbon in pulp/leach (CIP/L) treatment process [1]. This paper desribes an alternative pre-CIP/L treatment option for use in the Eastern Goldfields based on the chlorination of arsenopyrite by chlor-alkali technology [3] using the salt resources available from saline water present in abundance in the region.

Jan 1, 1995

By M. I. M. Darwish

In this paper, an effort was made to get more in-sight about the parameters that can affect air sparging technique optimization. Numerical simulations were used in predicting the effects of different parameters utilizing Shell?s in house MoRes simulator. The case of using air sparging to remediate source zone is considered in this work. Different air injection scenarios using continuous and pulsed air injection techniques, with different frequencies and durations, were compared. The amount of MTBE mass removed from the saturated zone and arrived to the ground surface, through the vadose zone, was the main criterion while comparing different air injection scenarios. The simulations results showed that pulsed air injection is better than continuous air injection in removing the MTBE and that the longer the OFF time is the better the MTBE removal.

Jan 1, 2008

By Patricia T. Foley

An analysis of the demand for copper shows a widely varying pattern of end use. For example, copper tube is the most popular material for hot water supply in the US and northern Europe, but galvanized steel is used in Japan and plastics are used in developing countries. In addition to such peculiarities of end use, the demand for copper varies among countries depending on the stage of industrialization and the extent that the copper processing industries are developed. Brazil, with its abundant supplies of bauxite and hydroelectric power, uses aluminun in place of copper wherever possible. South Korea, with its export oriented economy and its advanced custom smelting and fabricating industries, favors copper. Understanding the details of demand in different countries enhances statistical derived forecasts and illustrates potential new markets.

Jan 1, 1986

By M. Sheppard, P. Wand, G. A. Cooper, M. Lesage

The vibrations generated by a tricone drill bit are caused by the successive impacts of the bit teeth on the rock, and peaks in the vibration spectrum can be associated with impacts coming from particular rows of teeth on one or other of the bit cones. Wear of the bit teeth causes a shift of these peaks to higher frequencies at constant bit rotary speed, whereas changes in rock type generally produce changes in peak height. Bit bearing failure or poor hole-bottom cleaning both cause loss of definition in the spectrum, the latter often associated with spurious high-amplitude signals at low frequency. The vibration signals may also be analysed in the time domain, where, for example, cone locking can be identified by characteristic features in the signal of torsional acceleration.

Jan 1, 1987

By Greg P. Timms, John W. Bennett

Monitoring on Whites waste rock dump at Rum Jungle has provided a unique opportunity to assess the effectiveness of a cover in the medium term. Temperature and oxygen concentration profiles have been measured continuously, from some years before the cover was put in place in 1983 until the present. Lysimeters have been used to measure water infiltration rates. Heat and oxygen transport processes in the dump have been modelled and compared with field data, enabling oxidation rates to be quantified both before and after the cover was put in place. It has been found that the cover reduced the overall oxidation rate to between one third and one half of the uncovered rate. There is evidence that both the overall oxidation rate and water infiltration rate have increased in recent years.

Jan 1, 2000

By R. D. Kelsey

The theory, definition and practical application of cutoff grades have evolved over a long period. This evolution is reflected in the continuing flow of papers on this and other related matters though the rate has varied as new ideas and theories have become understood and applied in practice. Papers by Lane(l) in 1964 and Taylor(-2)- in 1972 provided landmarks in the understanding and general communication of cutoff grade theory and its application. The reasons for the continuing interest in cutoff grades are obvious. Too high a cutoff can reduce the mineral recovered and possibly the life of a deposit. Too low a cutoff would reduce the average grade (and hence profit) below acceptable levels. This paper provides a brief overview of existing cutoff grade theory and some particular aspects of its application.

Jan 1, 1979

By P. Somasundaran, Brij M. Moudgil

All the major interfacial technologies encountered in mineral processing involve adsorption of surfactants and/or polymers. With the need for processing low grade complex ores it is imperative that conventional techniques such as flotation and flocculation be extended to meet the challenge of treatment of fines. Addition of surfactants or polymers is indeed not limited to the solid-solid separations but extends to particle size reduction in the form of grinding aids and dewatering operations as well. Although progress has been made in recent years to understand the science involved in various interfacial processes, more challenges and opportunities exist today than ever before in processing of the low grade finely disseminated ores. A brief review of the recent advances and the challenges in mineral processing, especially, those related to the interfacial technologies is presented.

Jan 1, 1989

By Y. Q. Zhang, Y. Luo, S. S. Peng

Burrier pillars in underground coal mines could eventually be subjected to a water head due to the build-up of mine water in the old workings. The water head could not only act ns a force to destabilize the pillar, but it could also cause seepage flow through the pillar and its surrounding strata. Excessive seepage flow could induce piping failure that, ill turn, could accelerate the mechanical failure process of the barrier pillars. In this paper, a finite element simulation approach was employed in the evaluation of the barrier pillars. Both the stress distribution and the seepage flow pattern in and around a barrier pillar have been simulated numerically. The effects of ground stress on rock permeability to water seepage has been taken into consideration in these simulations,

Jan 1, 2002

By Joyce A. Ober

Strontium occurs commonly in nature, averaging 0.034% of all igneous rock; however, only two minerals, celestite and strontianite, contain strontium in sufficient quantities to make its recovery practical, and these minerals are found in sedimentary rocks. Of the two, only celestite has been found to occur in deposits of sufficient size to make development of mining facilities currently attractive. Celestite, the most common strontium mineral, consists primarily of strontium sulfate (SrSO,). Strontianite, the second most common mineral, consists primarily of strontium carbonate (Sr CO3). Strontianite would be the more useful of the two common minerals because strontium is used most commonly in the carbonate form, but few deposits have been discovered that are suitable for development. The physical properties of strontium ores are listed in [Table 1].

Jan 1, 1994

Since gold was first discovered in Colorado in the late 1850s' mining has been a major part of the state's economic history, according to Stanley Dempsey, chairman and chief executive officer of Denver- based Royal Gold Inc. While the mining industry has seen some lean times throughout the past century, it has always bounced back. Today, dozens of major gold companies are headquartered in the Denver area. The state's coal mines produced record amounts during 1996. And even some of Colorado's uranium mines are resuming production. Dempsey joined other speakers in addressing the state of Colorado's mining industry during the Colorado Mining Association's (CMA) National Western Mining Conference. Some 800 people attended the CMA meeting, held Feb. 2-5 in Denver. The meeting was the association's 100th since it was incorporated in 1897.

Jan 1, 1997

By R. D. Deister

The Buick concentrator represents state-of-the-art technology in automated digital process control operation utilizing a centralized computer. The process control strategies implemented at Buick are no longer new to the industry, but the successful application of these developments is still rather unique in North America. Productivity improvements, determined to be a direct result of the process control developments, are the primary topics of this paper. Emphasis is placed on metallurgical benefits including both lead and zinc recoveries; lead concentrate grade; and reductions realized in reagent consumptions, operating costs, and personnel. A detailed description of the concentrator, along with a history of the process control development and a more in-depth discussion of the control strategies implemented at Buick can be found in the references. (The Buick flowsheet is depicted in Fig. 1).

Jan 1, 1987

By C. W. Hunt

I wish to register strong disagreement with the choices of drilling sites chosen by the Continental Scientific Drilling Committee, while endorsing the stated objectives. Of special significance is the lack of any site involving the metals most needed today in the US, while 9 to 13 km of drilling are allocated to gold and silver districts and 11 to 17 km to base metal (mainly copper) districts. Why is nothing proposed for platinum group or chromite? Is this because the committee did not know of such a site? If so, I offer such a site in California (see Fig. 1). The mineralization shown in Table 1 occurs in a large peridotite body in western Tehama County, CA. Petrography has demonstrated unequivocal evidence of migrated PGE deposited in peridotite and chromite of hypabyssal nature. Active diapirism (due probably to serpentine buoyancy) above a reactivated mantle to surface conduit marks the position of the conduit. Young explosion breccia cemented loosely by volcanic glass and tuff demonstrates the significance of the conduit as the prime source of the various emissions. Deep drilling could result in major metals discoveries as well as shedding light on the grand questions of platinum group mineralization. What role water has played in this occurrence is not yet certain; but chlorine and asphaltite have been detected in and adjacent to native PGM, suggesting a major role for water. The explosion breccia suggests that this excellent site could overlie entrapped geothermal steam.

Jan 1, 1988