Search Documents

By W. M. Schafer, C. F. Luckay, D. A. King

Monitoring devices have been installed at several mine sites to assess the potential for the development of acid rock drainage (ARD) in waste rock, spent ore and tailings material. In addition, instrumentation has been designed for monitoring changes in water quality in pit lakes. These devices monitor temperature, oxygen, water movement and water chemistry in the waste rock pile. This information can be used to evaluate the current and future ARD risks and the effectiveness of caps and covers. The information can also be used in the design of other reclamation strategies that limit ARD development. The instrumentation includes nested thermistors and oxygen sensing ports, neutron access tubes, heat dissipation units (HDUs) and lysimeters. Many of the monitoring devices can be linked to a data logger and telemetry systems, enabling monitoring data to be downloaded from the office.

Jan 1, 1999

A series of laboratory based push and pull tests were carried out to investigate how surface profile influence the load transfer mechanism of bolt/resin interface. Tests were carried out in both 75 mm and 150 mm long steel sleeves. Three types of bolts were examined, they were bolts most commonly used for strata reinforcements in underground coal mines in Australia. The bolts had near equal core diameter but of different profile configurations. The change in the length of the encapsulation sleeve was examined in light of the small number of profiles encapsulated effectively in short 75 mm long sleeves. The results showed that peak loads and displacements were directly related to the height and the spacing of the bolt surface profiles. Profile spacing appears to have greater influence on load transfer capacity than the profile height.

Jan 1, 2006

By Chris Groccia, Damodara R. Chinnasane

Vale is in the process of resuming mining in the lower 810 ore body (810 OB) below 4130L at Copper Cliff Mine – South Side. Production in the lower 810 OB had continued until it was temporarily ceased in 2017 to allow for the execution of activities associated with Copper Cliff Mine Phase 1 project. While mining the stopes in both the lower and mid part of the 810 OB, a seismic response was experienced that resulted in rockbursts and challenging mining conditions. The majority of the rockbursts experienced in the past were associated with stopes mined in a bottom-up mining sequence under a diminishing pillar situation between 3350L and 3540L. The current mining plan is comprised of both top-down and bottom-up mining fronts using a center-out chevron sequence of long hole open stopes to manage induced stresses. Numerical modeling assessments have been carried out to forecast the response of the rock mass due to the planned mining. Seismicity and stress induced damage surrounding excavations are anticipated, and areas requiring extra attention have been identified. A tactical approach is being used to prepare the area for production, including replacement of ground support elements that are damaged or have insufficient residual capacity, and installation of dynamic support in areas anticipated to experience bulking and/or dynamic loading that would exceed the current support system’s capacity. A series of monitoring programs are being put in place to confirm current conditions, and to monitor the response of the rock mass to proactively implement ground control tactics should the need arise. This paper provides a summary of the approach used to forecast, monitor, and manage the behavior of the 810 OB rock mass response to continued mining at depth.

Apr 26, 2022

By Robert A. Bauer

Introduction A longwall mining demonstration currently in progress in the Herrin (No.6) Coal Member near Benton, Illinois, involves the extraction of three adjacent panels by the longwall method. The first panel was completed in May, 1977. The Illinois State Geological Survey is involved in this project for two reasons: (1) to detail the geology of the roof and relate the geologic features to the behavior of the roof during mining operations, and (2) to study the nature and occurrence of coal balls (carbonate petrifactions of peat) encountered during this demonstration. General Geology of Area The stratigraphic sequence of beds immediately above the No. 6 Coal in this area, ranging from oldest to youngest, is: gray shale (Energy Shale Member), black carbonaceous shale (Anna Shale Member), and argillaceous limestone (Brereton Limestone Member) (figure 1). In some areas of the mine, where one of these units may rest directly on the coal, one or more of the members is absent from the stratigraphic sequence. The nature of roof for the area is shown in figure 2. It is greatly exaggerated in the vertical direction. The Walshville Channel, 11.3 km west of this mine, was a river at least in part deposited at the same time as the coal. The gray shale wedge on top of the coal, which thins away from the channel, is thought to represent an overbank deposit of mud from the channel. The next layer deposited on top of the gray shale, and on the coal not covered by gray shale, is the black carbonaceous shale, believed to represent a mud deposited in a brackish environment. The area where the roof lithologies change rapidly from one shale to

Jan 1, 1977

By William Gleason

The world has seen unprecedented economic changes in recent years, starting with the stock market collapse of 2008 and the great recession that followed. With these changes, the mining industry, like others, has been forced to find ways to adapt to the shifting and sometimes volatile conditions. It has been a bumpy ride that has not been easy. Prices for most commodities have been in a decline in the past several quarters ? albeit still well above the average prices of 10 years ago ? as the costs of production have been on a steady incline for the past 10 years. Adding to the concern was the report in April that China, which had grown at an average pace of 10 percent/year, for the past decade, slowed to less than 8 percent gross domestic product (GDP) growth this year, catching many off guard. Even gold, once the safe haven for investors during rocky times, stumbled in April of this year, losing 7 percent of its value in two days. So what?s an investor to do ? and how can companies still attract financing? For the first time in 10 years, SME, in conjunction with the New York Local Section of SME, attempted to clear the waters of the mining finance sector with a conference focused on ?Current Trends in Mining Finance.? Held at City University of New York, Graduate Center, April 29-30, the two-day conference attracted 148 attendees and was intended for senior executives and mining industry specialists, covering a range of important topics and trends through 17 panels with about 50 speakers. The presentations came from representatives from some of the most influential companies in the mining and financial sectors, including Citi, Nomura, Societe Generale, Caterpillar, Newmont Mining Corp., Ernst & Young, Export Development Canada (EDC), KPMG, HSBC, Tocqueville Asset Management, BNP Paribas, Revett Minerals, Royal Gold, Environ and ERM.

Jul 1, 2013

By Jordan Hoover, Erika Moonin, Chuck George

"In response to a severe regional drought and in preparation for the further decline of water levels in Southern Nevada’s Lake Mead, the Southern Nevada Water Authority (SNWA) built a new intake system to ensure water supply to Las Vegas and its surrounding communities. In 2015, design began on the Low Lake Level Pumping Station (L3PS) that will move the water from this lower intake, ensuring operability of the water delivery system despite these declining lake levels. The L3PS Project includes a 159-meter-deep shaft, a large underground chamber, and 34-each 152-meter-deep, 2.4-meter-diameter drilled well shafts to be constructed in highly faulted and fractured ground. The Construction Manager at Risk (CMAR) delivery method was chosen to facilitate early contractor involvement in the design process to address the significant challenges and risks anticipated on this US$650 million Project. This paper describes the CMAR selection process; the CMAR involvement during design and benefits resulting from that involvement; and the unique collaborative effort among the owner, engineer, program manager and CMAR used to evaluate and select the best design approach, preferred underground construction methods, and coordinated geotechnical baseline report. PROJECT BACKGROUND AND NEED Seven of the United States’ western states rely heavily on the Colorado River and its tributaries for their water supply. The primary source of water for the Colorado River is winter snow that falls in the mountains ringing the Colorado River Basin. Flows in the Colorado River vary significantly from year to year, depending on the amount of snow and rain deposited in the basin. Beginning in the year 2000 and continuing to the present, snowfall has been well below documented historical averages and Colorado River flows have diminished."

Jan 1, 2016

By William C. York-Feirn, Jeffrey H. Kravitz, David Stalfort

"Mining is an inherently risky business. Over the years, major mine disasters have resulted in the deaths and injuries of thousands of miners in the United States. These disasters also resulted in innovations in approaches to mine design, operations and the training of miners and mine rescue teams. The U.S. Congress responded to these disasters with new laws designed to create mandatory safety and health standards as a means to eliminate fatal accidents; to reduce the frequency and severity of nonfatal accidents; to minimize health hazards and to promote improved safety and health conditions in the nation’s mines.Following a mine emergency preparedness and response holistic gap analysis in 2012, the U.S. Mine Safety and Health Administration (MSHA) identified the need for the development of risk and readiness assessment models for MSHA and the mining industry. MSHA’s objective was to evolve existing theoretical concepts for risk and readiness assessment into simplified tools that can be applied by the mining industry for use at operational levels. In 2012, MSHA hired ABS Group, a recognized industry leader in safety risk management and a wholly owned subsidiary of the American Bureau of Shipping, to develop self-assessment models to help meet this objective.In September 2012, MSHA chartered a project to supply the coal mining industry with a pro-active toolset for mine operators to:1. Self-assess the risks associated with underground coal mining operations in order to prevent major mine emergencies.2. Assess the preparedness of mine operators to respond to an emergency.3. Measure the readiness of mine rescue teams and responsible persons to execute emergency plans.MSHA’s objective was to evolve existing theoretical concepts for risk and readiness assessment into simplified tools that can be applied by the coal mining industry for use at operational levels."

Jan 10, 2018

By E. Maré

Some of the members will probably ask themselves what close relationship exists between hydro-metallurgy and a wet scrubber, but we are sure that as soon as deeper thought is given to the matter it will be realised how vital scrubbing, operations are in metallurgical plants. In ordinary metallurgical installations or pyro-metallurgical processes ore concentrates are first of all shifted from place to place and dust is created. In other cases the ores or concentrates are crushed or dried or roasted, and in each one of these operations dust and fumes, are created. All suspended particles and fumes originating from the abovementioned conditions not only, in many instances, provide health hazards which disrupt production and endanger the personnel in the plant, but also are the source of economic losses through extra maintenance and wear to moving machinery due to abrasion and corrosion. Further losses are incurred by the waste of fine, very often valuable, components. The Party who once said that in several metallurgical plants the bulk of the profits was discharged into the atmosphere by the stack wasn't stretching the truth. There is a place in Africa where a gold producing concern used to lose over 5 oz. of fine gold per day out of a total production of 3000 oz. per month. In another instance, copper concentrate going as high as 80% Cu was discharged into the atmosphere at the rate of 4 tons per day. Realising the value of removing and collecting solids and fumes created in metallurgical plants, a thorough study was made of the available plant and equipment offered on the market. Some units were found very efficient, but very expensive; some others also very efficient but with temperature and maintenance limitations. Some others were also efficient but prohibitive from the point of running costs.

Jan 1, 1963

By J. Mattern

Performance monitoring, operational practices and ongoing collection of geologic data in open pit slopes all provide valuable information for quantifying potential steepening of subsequent slopes. Mining at the Goldstrike open pit has been ongoing since the early 1980’s, with its share of slope instabilities. In areas where slopes have remained stable, consideration has been made for potential slope steepening of final walls. With the proper available equipment, steepening of bench face angles via pre-split blasting is not an uncommon method for steepening of inter-ramp slope angles. As an alternative at Goldstrike, the commonly used Modified Ritchie Criteria for empirical catch bench width has been adjusted resulting in quantified, rock specific formulas for bench width and rock fall berm placement. The result is an inter-ramp slope angle increase of 2 degrees on a 300m high slope, without the necessary purchases and procedural changes that would be required for pre-split drilling and blasting. The result has shown significant net benefits through reduction in mined waste tons and an increase in gold reserves. Location The Goldstrike open pit is located on the Carlin Trend gold belt in northeastern Nevada USA (Figure 1). The mine has produced over 43 million ounces (1.2M kg) of gold during the past 30 years. Engineering Geology Stratigraphy Figure 2 is a stratigraphic section of the rocks in the Goldstrike open pit. Quaternary alluvium and Miocene materials typically are poorly indurated stiff soils and are not present in all locations. Bedrock units consist of siltstones, mudstones, sandstones and cherts. From top down the major units exposed in the open pit are the Vinini Formation, the Rodeo Creek Unit, and the Popovich Formation. In general, rock mass strength increases with depth.

Jan 1, 2019

By Jonas Svensson

The Grangcold Pellet Process - for which patents have been applied or already granted in a number of countries - uses a hydraulic adhesive such as Portland cement, slag cements, pozzolanic cements, etc., for the production of cold bonded pellets. The idea of using a hydraulic binder for the agglomeration of iron ore fines is not new. Portland cement was proposed as an adhesive for cold bonded iron ore briquettes in patents granted more than 50 years ago (1). In a report on the briquetting of iron ore fines, published in Stahl and Eisen 1959 (2), it is stated that briquettes bonded with Portland cement are used on a small scale at on ironwork in Germany. According to the report, the briquettes showed excellent strength in the blast furnace although their general use was made impossible because they required a long hardening time, during which they are sticky, soft and difficult to store and handle. The Grangcold Pellet "recess has overcome this particular disadvantage by mixing the balls with a suitable amount of the balling concentrate before storing them. The pellets are embedded in the concentrate during storing in such a way that they are isolated from each other and thus prevented from sticking together to form clusters. Thanks to the embedding concentrate, the pellets are subjected to a more or less uniform pressure from all sides which does not deform them. Thus the mixture can he stored in a stockpile or in a silo until the pellets have hardened sufficiently. The concentrate is separated from the pellets by means of screening. The concentrate is returned to the balling operation and the pellets are either shipped to the blast furnace or stored for final hardening.

Jan 1, 1969

By L. B. Hales

Expert control of grinding and flotation plants has been successfully used in the minerals industry since the 1970?s. The earliest of these systems were written in a hard-coded fashion in FORTRAN, BASIC or Pascal. Second generation systems were built using the first experimental expert system shells that were being developed in the artificial intelligence community. Later systems were deployed in expert system shells designed for real-time processing plants that also included the ability to model the process with neural network models and optimize setpoint selection through the use of genetic algorithms. Significant performance increases have been achieved using these systems, but in general, they suffer from the static nature of their rules and to a degree the process models also. Typical improvements quoted in the literature suggest throughput rate increases of 4 to 8 percent and recovery increases of 1 to 4 percentage points. In over 30 years of designing and installing expert systems we have never seen performance numbers less that these but have often seen numbers in excess of the high values. However, once the system has been installed and tuned up the performance usually does not improve much thereafter. Granted, the initial increases in throughput rate and recovery are significant but a question always lingers, that is, can the expert strategies be modified further to squeeze a little more improvement out of the system. The answer to this question is a resounding yes, however a complete understanding of what we do well as designers and operators of expert control systems is required as well as how we can improve upon our best practices is required to move us from the performance plateau we have been on for a number of years to a new higher level of performance.

Jan 1, 2009

By J. Brendan Mclaughlin, Casimir J. Koshinski, Michael V. Rose, Wolfgang Baum

Mercury contamination is a worldwide problem in the mining, smelting, and refining of gold, silver, and copper. In these areas, mercury may be found as a naturally-occurring material in ores and concentrates, and/or in secondary feedstocks such as leach residues, pyrometallurgical treatment residues, refinery by­products, electrowinning electrodes, autoclave discharge solids, and waste water and acid plant sludges. The United States Environmental Protection Agency (EPA) has designated mercury one of the most harmful heavy metal contaminant in the environment and has implemented regulations that prohibit land disposal of characteristically hazardous wastes containing greater than 0.20 mg/1 TCLP mercury without prior treatment, thus increasing the cost of managing these materials. The presence of mercury in mine, smelter, and refinery by­products and wastes severely decreases, and in some cases eliminates, the ability to recover residual metal values from the contaminated material. The lost revenue associated with this disposal, combined with the increased direct cost of waste treatment, and/or disposal and protecting workers and the environment, can adversely affect overall profitability. The safe, efficient, and economical removal of mercury from gold, silver, and copper mining by-products requires a treatment process that is capable of liberating the mercury from the wide variety of compounds and matrices in which it may be contained, reducing the mercury content in the matrix to desired levels, and recovering the mercury in pure saleable form, without producing any secondary solid, liquid, or gaseous wastes. This paper reviews results from commercial operations and pilot scale tests using a thermal process owned and operated by Mercury Recovery Services, Inc. (MRS) to remove and recover mercury from copper acid plant blowdown sludge, Merrill­Crowe precipitate from gold/silver mining operations, and Cottrell and salt slag dusts from a precious metals refinery.

Jan 1, 1997

By Mark W. Johns

The design or optimization of a carbon-in-pulp (CIP) plant requires the determination and setting of a number of parameters to ensure optimum economic performance. A number of these parameters are either fixed, a function of the pulp, interdepen­dent, affect other parameters or outputs, so only a limited number of degrees of freedom exist from a metallurgical point of view. The traditional CIP contactor employs a low carbon concen­tration, a low agitation intensity and a reasonably long pulp residence time. The pump cell contactor employs a high carbon concentration, a high agitation intensity and a reasonably short pulp residence time. The two philosophies are dipolar in nature and the question arises as to which configuration is the optimum configuration for a CIP plant. The carbon particle size is shown to have a small effect on the capital cost of a CIP plant. A decrease in the pulp residence time, an increase in the pulp density, an increase in the carbon residence time, an increase in the agitation intensity and an increase in the number of stages are shown to have a positive effect on the capital cost of a CIP plant. The pulp residence time, the pulp density and carbon particle size are shown to have a small effect on the operating cost of a CIP plant. An increase in the carbon residence time, a decrease in the agitation intensity and an increase in the number of stages are shown to have a positive effect on the operating cost of a CIP plant. The optimum CIP plant, therefore, employs a short pulp residence time, the traditional pulp density, a long carbon residence time, the traditional carbon particle size, the traditional agitation intensity, and the traditional number of stages. Neither the pump cell configuration nor the traditional CIP configurations match the optimum configuration.

Jan 1, 1995

By Gregg Wilkerson

The Blind Springs Hill pumice beds are located 5 miles southwest of Benton, California in the foothills between the Benton Mountain Range and Blind Springs Valley. The best exposures of the pumice are in an area 0.75 miles west of Blind Springs Hill. The pumice is Quaternary ejecta material which came from the rhyolitic volcanoes in the Glass Mountain-Volcanic Tablelands area of Mono County. The pumice beds occur in two distinct layers separated by an unconformity. The upper layer is 0 to 11 feet thick and consists of coarse subangular pumice fragments, some of which are over 1.75 inches in diameter. The lower bed is medium to coarse grained with subangular fragments up to 1.0 inch. The lower bed is 0 to 9 feet thick. Overburden at the Blind Springs Hill deposit varies from 0 to 15 feet. There are approximately 1 million cubic yards of material in the deposit that can be mined. The size distribution in the deposit is mostly fine with only 10.6% of the pumice fragments being over 0.5 inch in diameter, the minimum size needed for stone-wash or acid-wash applications. Suitability of pumice for the textile industry is quantified by standard 15-minute abrasion and absorption tests. In the Blind Springs Hill deposit, the plus 0.5 inch fraction has an abrasion loss of 33% which is too high for stone-wash application but it has an absorption capacity of 36% which makes it suitable for acid-wash applications in the textile industry. The abrasion and absorption properties of this deposit are within the range of those which have been measured for other pumice deposits within the United States.

Jan 1, 1995

By William T. Folwell

INTRODUCTION - CURRENT RAISE BORING PRACTICES Raise boring is a comparatively new tool to the underground mining and construction industries. Underground raise boring, in this country, had its beginning in the early 1960's, in the iron mines of Michigan. These first raises were bored 40 in. and 48 in. in diameter with maximum lengths of approximately 200 ft. Since the late "sixties", the raise boring machine has been accepted by the mining industry as an important machine to increase excavation rates, provide adequate ventilation airways, improve safety, and reduce costs, to name a few of the benefits. The construction industry is now accepting raise boring techniques for hydro-electric power projects, water supply projects, tunnel projects, waste water projects, etc. Raise drills are now capable of boring raises to diameters as much as 12 ft, in the softer rock types. Raise lengths range from 200 ft to as long as 1700 ft. Bored raises, in general, are bored at dip angles ranging from 45º to 90º, depending on the requirement of the raise. The general practice is to drill the pilot hole down to an opening below and up ream the pilot hole to the required diameter. The pilot hole (9-7/8", 9", 11", or 12-1/4" diameter) is generally drilled with compressed air to remove the cuttings. In the event that ground water is encountered and removal of cuttings is impeded, a foaming agent is added to assist in lifting the cuttings. When excessive water is encountered, water is used as the circulation medium and the cuttings are removed by pumping. During the reaming cycle, the cuttings fall by gravity and are removed from the bottom of the raise by conventional methods.

Jan 1, 1997

By H. Lyn Bourne

The is the 14th consecutive year for this column and the 13th in which the royalty data have been tabulated. Some holes still exist in the list of royalties that readers hopefully will fill. Construction aggregates - either sand and gravel or crushed stone - are the most common mineral commodity. In spite of their pervasive use nationwide, royalty information for these commodities has been difficult to acquire from some states. Readers can help. Share information about these missing states and next year there will be fewer states without information. Dennis Bryan sent a copy of a report, "Regional Appraisal of Mineral Materials: Carson City District, BLM." The report was authored by real-estate appraisers. It contains more than 50 references to leases of various construction materials in Nevada and nearby states. It gives a thumbnail sketch of each lease and is a good reference. However, the authors erroneously imply that the royalty rate and the in-place value are the same. Several of this year's new entries come from the report. However, the royalties for landscaping materials vary from state to state and by rock type. Some boulders used for landscaping in Nevada have a royalty reported at $1.10/t ($1/st). At the other extreme is lava from Idaho. Used for the same purpose, it has a royalty range of $11 to $18.70/t ($10 to $17/st). Chuanming Tian of Beijing, China has shared some information about the changing mineral royalty policies in China. China first implemented an oil and gas royalty in 1984. In 1992, the government expanded that to include iron ore. In 1994, the royalty policy was extended to all mineral commodities. At the same time, the royalty rate for iron ore increased tenfold.

Jan 1, 1995

By A. C. Lyons, A. J. Reed

INTRODUCTION A trend which is obvious in the United Kingdom and is thought to be evident in other parts of the Western world is the disproportionate rise in the cost of tunnel mining labour compared with other tunnel cost increases. This disproportionate increase in labour costs has been accompanied by, and may be the result of, a shortage of skilled working labour. To combat this problem there has been a steady increase in the use of machines for excavation and for the erection of tunnel linings to keep the amount of skilled labour working below ground to a minimum. The typical tunnelling cycle, where the ground needs continuous support can be excavation, temporary support, temporary lining, grouting and permanent lining. It is obviously an advantage to combine as many of these operations as possible and carry out as much as possible by machine. Machines have been developed which will, either alone or used in combination with a shield, excavate and, when necessary, temporarily support the excavation. If a segmental lining is used, it can be so designed that it will form the permanent lining and reduce the cycle time and skilled labour requirement to a minimum. In cases in which the ground can be cut accurately to a smooth profile and will stand without support for a sufficient time, the lining can be expanded against the ground and the necessity of grouting eliminated. In cases in which ground will not stand without support, the usual method is to use a bolted lining and to grout behind it preferably as the shield is shoved forward. Whichever technique is used (this is largely determined by the ground) it is an advantage to make the segments as large

Jan 1, 1974

By Warren E. Fife

This paper will discuss the application of a continuous miner using a fixed drum milling type cutting head for the underground mining of hard rock and salt ores. Continuous mining machines of the ripper chain cutting head, oscillating milling cutting head and boring arm designs have been used in rock and salt applications with various degrees of success. The large boring arm miners have been successful in potash, trona and salt, but they have not been successful in mining rock materials like iron ore. The main method used in underground mining rock materials is the conventional drilling and blasting the ore from the solid. This is particularly true for the harder, more abrasive copper and iron bearing ores. The softer salt based ores of potash, trona and rock salt can use several underground mining methods depending on seam conditions. Several of these methods use underground coal mining equipment that has been extensively redesigned to adapt it for use in mining noncoal materials. Conventional mining methods employ the use of a universal cutting machine to undercut or topcut the ore body before face drilling and blasting takes place to produce a smooth parting of the ore. The boring arm continuous miner is widely used in underground mining of potash and trona ores. It produces a tunnel with a smooth semicircular contour which results in good rib and roof stability. The ripper chain continuous miner is also widely used in mining the salt based ores of potash, trona and rock salt. They are used more frequently in Europe than in the United States and Canada. Some reasons for using the mechanical mining machines as opposed to the conventional drilling and blasting techniques for mining hard rock ore bodies are the resulting improved rib and roof control, facilitates selective mining of the ore body, and requires less man-

Jan 1, 1974

By Rainer Kahrger, Guenter Ewald

The topic of this paper is to demonstrate the development of mobile crushing installations from throughput capacities of 200 tons per hour, to mobile and semi-mobile large- scale crushing installations with throughput capacities of 3,500 up to 10,000 tons per hour. Basis are approximately 140 mobile and semi-mobile crushing installations which have been built since 1956 or were on order in 1987. [FIGURE 1. Total Number of Mobile or Semi-mobile Crushing Plants] Sixteen of these approximate 140 mobile and semi-mobile crushing installations have a throughput higher than 3,500 metric tons per hour. Mobile crushers were developed more than 25 years ago in Europe for the quarry industry, which had special requirements - fairly low capacity, mostly softer and less abrasive material (limestone) and full mobility. So the majority of the units up to about 1980 were fully mobile, having a fairly small capacity and utilizing mainly hammermills, double roll and impact crushers. It was only when the mining industry and large quarries picked up the concept in the early 1980's that a drastic increase in capacity took place. Even though the first mobile crusher in a true mining application went into service in 1971, it took another 10 years before it proceeded in a larger scale. This trend was obviously supported by the drastic fuel price and energy cost increase in the mid 70's. Since the cost of conveying material is substantially cheaper than trucking it, the increase in energy cost, combined with increasing haulage distances provided a strong incentive. Figure 1 shows clearly the throughput distribution of all crushing installations and it also shows the sharp increase in the throughput capacities within the last few years.

Jan 1, 1989

By John L. Schroder

The design of an underground mining operation requires the integration of transportation, ventilation, ground control, and mining methods to form a system which provides the highest possible degree of safety for mine personnel; the lowest cost per ton of product; the most suitable quality of final product, considering its intended use; the maximum percent recovery of the reserve, consistent with cost and subsidence rights; and the minimum disturbance to the environment. The selection of mining method is generally the controlling factor in overall mine design. Some important considerations in the choice of mining method are : 1) Depth of cover over the coal seam. 2) Strength and thickness of rock strata in the overburden. 3) Characteristics of the coal seam, including thickness, nature and location of impurities or irregularities, dip (or pitch), nature and direction of cleavage, hardness, and structural strength of the coal. 4) Nature and strength of the immediate roof (top) over the coal seam. 5) Nature and strength of the floor (bottom) under the coal seam. 6) Presence and amount of explosive gas (methane). 7) Quantity of water likely to be encountered in the mining operation. 8) Any previous or concurrent mining in seams above or below the coal seam to be worked. 9) Any restrictions on recovery required for subsidence control. Topographical and geological reports and maps of the area are usually available from state and federal geological surveys, and contain excellent general information to guide more detailed investigations. Exploratory drilling, and the plotting and analysis of the information thus obtained, are essential steps in any development program, and aid in the correlation and evaluation of information gained by other means. Other good sources of information are operating coal mines that may be in the same seam in nearby properties. Such mines may indicate in advance much about roof control, drainage, ventilation, and other mining problems.

Jan 1, 1981