Search Documents

By S. L. Bessinger

Introduction Extensive testing in the past ten years has shown that where a uniform natural gamma background is present in the strata bordering a seam, the thickness of the boundary coal left in place after mining can be determined by measuring the attenuation of that radiation (Nelson and Bessinger, 1989). Measurements made by the authors in underground mines in Pennsylvania, West Virginia, Ohio, Illinois and Kentucky and by others in Wyoming and New Mexico have shown the presence of such a gamma background (Nelson. 1989). Natural gamma coal-thickness sensors of several configurations have been tested in mines owned and operated by the Consolidation Coal Company (Consol) in Pennsylvania and West Virginia (Nelson and Bessinger, 1988). This paper describes the installation of a natural gamma coal-thickness sensor on an operating continuous miner. Previous tests had shown that the NGB-1000 coal-thickness sensor manufactured by American Mining Electronics, Inc., of Huntsville. AL, is an accurate, mine-worthy instrument. This large gamma detector consists of a sensing head and a control panel. The sensing head contains thallium-doped, sodium iodide scintillating crystal, which is coupled to a photomultiplier tube. The control panel contains the electronic components required for calibration, count conversion and display to the operator. Methods Conditions at a Consol mine in northern West Virginia require that 10 to 15 cm (4 to 6 in.) of coal be left at the roof boundary of continuous miner development sections. This roof coal is required because the shale of the immediate roof is friable and unstable. In the past, operators have used a dirt band that is usually visible near the top of the seam as a guide in maintaining the proper cutting horizon. However, this is not always reliable. Earlier observation showed that the actual thickness of the coal left on the roof varied widely; further, it was noted that occasional, accidental excursions into the immediate roof required supplementary roof control measures, such as installation of planks or center bolts. Thus, it was concluded that operators needed a better source of guidance for control of the cutting horizon, and a roof-coal thickness sensor was scheduled for installation. The NGB-1000 sensor was installed on a Joy 12CM10 continuous miner in June 1988. The sensing head was mounted on the cutter boom of the miner, and the control panel was mounted in the operator's cab. Power for the sensor was initially derived from an intrinsically safe battery power supply. Initial measurements with the sensor showed that the calibration was the same as that used in earlier tests at two other mines, indicating the uniformity of the natural gamma background above the Pittsburgh seam. Operating personnel were initially skeptical of the instrument's accuracy, and were hesitant to use its readings as a guide in maintaining a proper cutting horizon. Because gamma attenuation, the instrument's operating principle, is somewhat abstract, attempts to demonstrate the instrument's accuracy by explaining that principle were generally ineffective. It was found, however, that an operator could usually be convinced of the usefulness of the instrument by placing a large piece of coal of fairly uniform thickness over the instrument's sensing head and allowing the operator to see that the instrument reading increased by an amount very near his estimate of the thickness of the piece. The mine was provided with seven battery power supplies and a charging station. The charging station was kept in the lampman's office, and the mechanic on each shift was instructed that he was responsible for two battery power supplies each day: a freshly charged one to be taken in at the beginning of his shift and a depleted one to be brought out at the end. This system worked well for a few weeks, but eventually some battery power supplies were left in use so long that their batteries were discharged too deeply to allow recharging. In addition, transport and recharging of the batteries represented an additional task for the mechanics, who were already very busy. Consequently, a request was filed with MSHA to allow the sensor to be powered through intrinsic safety barriers by an electronic power supply connected to machine power. The permit was granted, and the sensor was connected to machine power. After the sensor was connected to machine power, the only operating problem experienced was occasional failure of cables. A supply of the required cables was made and delivered to the mine so damaged cables could be quickly replaced. Much of the cable damage could be eliminated by slight modifications to the miner during a rebuild, so that cables could be installed in more protected locations. After the sensor had been in operation for about two months, a survey was made to determine its effect on continuous miner operations. In previous research, coal thickness measurements made in 88 locations by the natural gamma method were compared to measurements made in the same locations by observing drill cuttings and by inspections of drill holes with a borescope. That research showed that the gamma method is at least as accurate as the other two methods (Nelson and Bessinger, 1989) and is also much easier to use. The object of the survey described here was not to assess the accuracy of the natural gamma measurements. but rather to determine the effectiveness of the sensor output as a guide for the operator in maintaining control of the cutting horizon. Thus a smaller, hand-held gamma detector

Jan 1, 1992

By C. Zhou, B. Whisner, J. Carr

Proximity Detection Systems (PDSs) are used in the mining industry for protecting mine workers from striking, pinning, and crushing injuries when they work in close proximity to heavy machines such as continuous mining machines (CMMs). Currently all Mine Safety and Health Administration (MSHA) approved PDSs are magnetic field based systems which can be influenced by the presence of wire mesh that is commonly used for supporting roof and ribs in underground coal m ines. In this paper, researchers at the National Institute for Occupational Safety and Health (NIOSH) characterize the influence of the mesh on the performance of magnetic PDSs by measuring the magnetic field difference around a CMM caused by the presence of the mesh. The results show that the magnetic fields are generally enhanced by the mesh which causes the PDS detection zones to be increased correspondingly. It was discovered that the fields around the joints of two mesh sections have the greatest enhancement and thus deserve more attention. In addition, it is found that the presence of mesh can also cause a variation in the generator current. The influence of mesh is characterized by the change in the generator current with respect to the distance between the generator and the mesh. It was found that the generator current change caused by the mesh can be significant (on the order of ten) when the mesh is extremely close to the generator (e.g, less than 1 cm) and is negligible when mesh is relatively far (greater than 0.15 m). The findings in this paper can be used to develop guidelines and best practices to mitigate the influence of mesh on PDSs. INTRODUCTION The Mine Safety and Health Administration (MSHA) requires operators of underground coal mines to equip place-changing continuous mining machines (CMMs) with proximity detection systems (PDSs) to protect mine workers from striking, pinning and crushing injuries when they work around these heavy machines. Although a variety of technologies can be implemented for proximity detection, the magnetic-field-based PDS that was originally developed at the National Institute for Occupational Safety and Health (NIOSH) has shown great effectiveness in challenging mining environments and currently all MSHA-approved PDSs are magnetic-field-based systems. As shown in Figure 1, a magnetic PDS typically includes two major components----the magnetic field generator and the Miner Wearable Component (MWC). Magnetic fields are generated by injecting a high electric current into a ferrite-rod antenna sealed in the generator. The magnetic field strength detected by an MWC varies with the distance between the MWC and the generator. In a typical PDS, multiple generators are mounted on different locations of the machine. The relative location/zone of an MWC is determined based on the field strengths from different generators picked by the MWC. Ideally, for a PDS to work properly in the underground, the magnetic fields generated by the different generators should be stable and not vary with the environment, as the system would interpret any variation of the magnetic field as a result of the distance change between the machine and the miner wearing the MWC. In reality, however, this is not always the case since magnetic fields can be altered by a number of environmental factors such as the presence of steel wire mesh that has been widely used in underground coal mines for supporting roof and ribs In this paper, the influence of mesh on the PDS performance is investigated and the magnetic field change caused by the mesh is measured.

Jan 1, 2019

By Thomas F. Stinson

Energy-producing states see severance taxes as attractive sources of increased revenues for otherwise tight budgets. Consumers in energy-poor states, however, protest that current rates are excessive and have moved to obtain a reduction. The US Supreme Court heard two cases questioning such taxes during its 1981 term, and Congress, in each of its last two sessions, has seriously considered measures placing a ceiling on severance tax rates. Although discussions usually focus on coal severance taxes levied by Montana and Wyoming, ramifications of changes in national policy are much larger, potentially affecting mineral taxes in all states. Severance taxes yield substantial revenues in some states, as illustrated in the accompanying table. In fiscal 1980, Texas collected more than $1.5 billion from such taxes, while Louisiana, Alaska, and Oklahoma collected $525 million, $507 million, and $436 million, respectively. Oil and natural gas production were the major items taxed. While the table shows only the 10 states with the largest severance tax collections, a total of 17 states had severance tax receipts exceeding $10 million in 1980. The enormous increases in severance tax revenue between 1970 and 1980 can be seen from the table by comparing columns A and B. For the 10 states shown, revenues increased from $650 million to $3.8 billion during that period, due to a combination of higher prices, increased production, and new or increased taxes. In most states, increases in prices and production were more evident than higher tax rates. Although the revenue increase is impressive, it understates the extent of changes occurring during the past decade. Since tax collections are shown for fiscal 1980, the full impact of the decontrol of domestic oil prices is not evident. Also, taxes on natural gas reflect controlled prices. When full de-control of natural gas occurs, significantly higher revenues can be expected in gas-producing states, even if tax rates, production, and world prices remain constant. These increases in severance tax revenues, coupled with further increases expected to accompany natural gas decontrol, have produced fears that a substantial transfer of income is taking place from residents of energy-poor states to those living in energy-rich areas. Others worry that increased severance tax revenues will be used to substitute for a substantial portion of state taxes that would have otherwise been collected from firms and individuals. The resulting improvements in tax climate, it is thought, may encourage firms and workers to migrate to energy-producing states. While these issues are often portrayed as pitting energy have-nots against the haves, such is not entirely the case. Much of the original impetus for limits on coal taxes came from Texas residents, the state collecting the most severance tax revenue. One way of gaining perspective on these concerns is by examining severance taxes per capita and as a percent of state tax collections (see columns C and D in the table). When this is done, Alaska, where 1980 taxes on oil and gas production totaled more than $1300 per capita (and 35% of all state tax collections), stands out as a special case. There, the state was able to eliminate some individual taxes, place revenues in a permanent trust fund, and consider offering a rebate of some previous income

Jan 4, 1982

By H. E. Epstein, B. K. Parekh, W. M. Goldberger

Comminution is the single most expensive operation in mineral processing. It consumes about 50% of the energy required for mineral extraction (Agar, 1976). Current comminution technology is both energy-intensive and inefficient. A novel noncontact comminution process concept was developed in this study, whereby selective lib¬eration of minerals from an ore could be potentially achieved. The process involves application of electric and ultrasonic energy to liberate minerals from gangue particles. Introduction The mineral industry is a large user of energy in the US. Energy usage is increasing as the grade of ores processed decreases. It is es¬timated that comminution of ores uses about 32 000 kWh (115 trillion kJ), or 2% of the electric power produced in the US (NMAB-365, 1981). Among other minerals, ce¬ment, iron, and copper processing plants are the largest users of en¬ergy in comminution. Very little of this energy used in conventional grinding (about 1%) is used to gen¬erate new surface. The remainder is wasted (Table 1). Thus, there are substantial energy-saving and economic incentives to improve the efficiency of crushing and grinding techniques for mineral recovery. With an energy efficiency of only 1%, it would seem possible to devise methods to significantly improve comminution technology. This requires that breakage force be applied only where needed, not indiscriminately as in a conven¬tional ball mill (NMAB-365, 1981). Can apparatus and methods be de¬ veloped for large-scale commer¬cial use that allow energy to be fo¬cused at intergranular bounda¬ries? If this can be done, mono¬mineral grains would remain in¬tact and the grinding action would be selective and substantially more efficient. The novel comminution process concept described in this paper uses a combination of electric and ultrasonic energy. This energy breaks the ore and selectively lib¬erates minerals. The process has also been termed a two-stage or electroacoustical comminution process (Goldberger, Epstein, and Parekh, 1982). The mineral grain boundary is usually the weakest area in an ore. By applying electri¬cal energy to the ore, the rock frac¬tures mostly at grain boundaries. At the same time, the electric shock creates secondary hairline fractures in the ore. Additional application of ultrasonic energy to this ore provides further break¬age. The concept was proven on a molybdenum porphyry ore but needs additional study. Technical Background There have been substantial im¬provements in milling machinery and grinding operations, but rela¬tively few attempts have been made to develop alternatives to conventional impact milling. Sev¬eral methods, however, have been investigated that relate to this study. In the early 1970s there was considerable interest in a size re¬duction method known as the Snyder Process (Cavanaugh, 1972). It involved charging coarse ore into a pressure chamber, pressur¬izing with a gas, and activating a quick-opening (15 msec ) dis¬charge valve that connected the chamber to a discharge duct. This allowed solids to fluidize and ac¬celerate, subjecting the material to a variety of impulse phenomena that caused the desired size reduction. Other nonimpact means of achieving breakage and selective size reduction have been de¬scribed in technical and patent literature. Kanellopoulos and Ball (1975) considered using heat to induce thermal stress in quartz¬ite. This would cause cracking and, thus, increase grinding efficiency. The use of electrical energy to induce thermal stress was studied by the General Elec¬tric Co., in cooperation with the Montana School of Mines, under a research grant from the Anaconda

Jan 9, 1984

By S. P. Chong, Peter V. Avotins

The iron and steel industry continues to operate at depressed production levels due to the low level of demand for steel and foundry products. Crude steel production in the Western world dropped by 13.7% from 459.3 Gt (506 billion st) in 1981 to 396.4 Gt (437 billion st). The reduction was particularly severe in North America where the industry suffered a loss of 37.3% from 123.6 to 77.5 Gt (136 to 85 billion st). This reduced level of production severely affected iron ore and agglomerates output. Substantial curtailment was made in both sintering and pelletizing plants to meet reduced demand. The pressure on these plant operators shifted from quantity to quality. With energy cost becoming an ever increasing part of production costs, conservation was a major area of emphasis. Iron Making Sinter has continued to be the favored burden for blast furnaces overseas. As hot metal production declined and excess sintering capacity developed, many of the overseas operators that have been using pellets found it advantageous on hot metal production cost to increase the ratio of sinter at the expense of pellets. This was the case despite the depressed price level of pellets in the world market. In North America where pellets have been the predominant burden material-mainly because it is necessary to pelletize the fine grain iron ores available domestically-there was also increased interest in sinter usage. Bethlehem Steel Corporation's 13.6-m (44.5-ft) furnace at Sparrows Point experimented with a burden with more than 70% of sinter during the second half of the year and indicated some favorable results as compared to its previous 50% super flux sinter and 50% acid pellet burden. The blast furnace operators continued to press for improved burden quality. In addition to the emphasis on the importance of burden chemistry and quality, uniformity, much emphasis was placed on improving reducibilitiy and high temperature metallurgical qualities. These burden properties were recognized to hold further promise in reducing fuels rates. Sintering With reduced consumption caused by the cutback in hot metal production, many sinter plants sat idle while others operated at greatly reduced rates. The deemphasis on production in many plants allowed them to experiment with various means to reduce operating costs. The most notable action was the introduction of low cost South American pellet feed fines into the sinter ore mix. These feed fines, which are finer than 150 µm (100 mesh) ore, were previously thought to be too fine for sintering. However, when the full production rate is not required the use of up to 40% in the ore mix was reported to be successful with the aid of burnt lime and adequate premixing and granulation of the sinter mix before sintering. The emphasis on quality and tighter cost control also has resulted in a further breakthrough in sintering technology. It was recognized that good feed preparation-including selection of compatible ores, good blending, good pseudo-particle formation, additive size control increased bed depth, and closed control of the sintering bed heat pattern-could allow the production of high quality sinters with much lower heat input and FeO level. Bed depth of more than 600 mm (23.6 in.) was practiced in a number of operations. Total heat input of better than 1.3 GJ/t (290,300 kcal per st) has been achieved. Kawasaki Steel's Chiba Works has also achieved a 5.3% SiO2 in the sinter with good quality. The low heat input approach allowed production

Jan 5, 1983

By Shan Mafi

he Broken Aro coal mine is located at the Woodbury Wildlife Preserve 11 km (7 miles) west of Coshocton, OH on State Route 541. Underground min¬ing at the 16-hm2 (40-acre) site took place during the 1910s. During the past five years, surface mining has occurred along the western and northern perimeters of the underground region. The Ohio Department of Natural Resources (ODNR), R&F Coal and American Electric Power (AEP) are involved in a project to remine the abandoned underground complex. The program also includes installing a mine seal made of fixated flue gas desulfurization (FGD) material. Previous mining activity in this area has resulted in an acid mine drainage (AMD) problem on portions of the reserve. In particular, a prominent AMD source is present in the Simmons Run drainage. The project goal is to eliminate or reduce the AMD that is discharging into the watershed. It was initially hoped that the Simmons Run drainage area could be economically mined. Accordingly, this area was included in the mine permit. However, experience with other previously mined areas on this reserve showed that the old mine workings were more extensive than originally thought. Old mine workings present several problems. The most significant are reduced coal recovery, poor coal quality and AMD liability. All of these problems increase mining costs. And the more extensive the old workings, the more significant the increase in cost. Based on R&F's experience with old mine workings in this area, it was decided that economic recovery of the Simmons Run drainage reserve was not possible. As a result, R&F excluded the Simmons Run drainage area from its early mine plans. Some time after it was decided not to affect the Simmons Run drainage area, R&F and ODNR's Division of Mining and Reclamation discussed the possibility of removing this area from the permit and attempting to correct the AMD problem as an Abandoned Mine Lands (AML) project. Specifically, the discussion centered around mining through a portion of the old mine workings to expose the mine openings in the highwall. Once exposed, the mine openings would be sealed using FGD material from the nearby Conesville power plant operated by AEP. In addition, there was interest in reclaiming the old tipple and associated gob pile located adjacent to Coshocton County Road 17 on the opposite side of Simmons Run. R&F attempted to eliminate the AMD problem by sealing the mine openings with FGD material. Once the seals were installed, they were covered with overburden. Monitoring wells were installed to determine the effectiveness of the seal and the inundation progress in the old mine workings as well as monitoring the quality of ground water. The project was jointly funded by revenue from the sale of the coal recovered during the project and AML funds. The FGD seal is expected to cause well water levels to increase above preseal elevations. However, the additional head pressure due to increased water depths in the underground mine may cause seepage through the bottom of the mine or out through the perimeter. The in¬creased water depth in the underground mine is expected to cause lower oxygen concentrations in the underground mine water. Since acidity is produced by oxidation of iron pyrites, less oxygen should result in better quality water. Monitoring wells will be installed before seal installation so that pre- and postseal water levels and well water quality can be determined. Surface sampling locations will be identified. These will be monitored before and after seal placement.

Jan 1, 1998

By Stanislaw Siewierski

One of the major problems in the exploitation of deep copper ore deposits in the Legnicko-Glogowski Copper Field is ground control and, in particular, roof control of the headings. The depth of copper deposits ranges from 600 to 1200 m. The parameters of ore-bearing rocks and the surrounding rocks show considerable variance of strength properties along the mining thickness (Fig. 1). The roof of the openings exploitation headings consists of dolomite-calciferous rocks. The roof strata consist of layers, the thickness of which vary from several centimeters to 0.6 m (sometimes to 1.0 m). These strata differ in strength and are characterized by igneous and sedimentary discontinuities. On the basis of studies in structure, properties and geological mining conditions of the roof strata in Polish copper mines, the method of roof classification has been developed. (1) This method uses the stability index "L" of the roof, calculated from [ ] The value of "t" ranges from 0, l to 0,8. Based on the value of "L", four classes of the roof (Table 1) corresponding to different degrees of fall hazard have been developed. The mining of copper ore deposit is carried out by a single lift room-and-pillar mining system or a two-stage room-and-pillar system with roof caving. (3, 4). The single lift room-and-pillar mining system is most often used. It consists in working of the deposit of 2.5 to 4.5 m mining thickness, 150-350 m long mining line, consisting of parallel room faces 6 m wide with pillars 5.7 or 16 m wide. As the mining line advances, cross-cuts joining individual rooms are made, thus forming support pillars 3x5, 7x7, 5x16, and 7x16 m (Fig. 2). The two-stage system (Fig. 3) mines the deposit with rooms 6 m wide into blocks 25 x 35 x 25 x 45 m. During the second step these pillars are worked with rooms and cross-cuts into pillars about 3 x 4 to 4 x 5 m (retreat mining). The pillars are crushed just before the fall of the roof. The maximum opening of workings in the two-step system is about 10 m, i.e. one belt entry and one row of bearing pillars. In single lift room-and-pillar systems it is about 35 m., i.e. three belt entries and three rows of bearing pillars. The support of the headings consists of expansion bolts 1.6-1.8 m installed in a bolting pattern 1.1 x 1.5 m. In both systems the fall step is about 10 m, i.e. the width of a belt and a bearing pillar. The Indications of Rock Mass Pressure Individual Dog Heading Individual dog headings are set wide apart from each other in the unmined ore deposit area where there is no interaction of headings. The indication of rock mass pressure are, in such cases, limited to the deformations and damage of side walls. Radiometric studies of rock mass loosening showed that the maximum range of lifts in side-walls immediately after web was 2 m (4,5). In the course of time the cracked side rocks fall off, thus widening the heading. The morphology of side-walls is influenced by the location of the heading in relation to clump layer/tarry. This layer is characterized by a weak strength and "lubricating" properties. The location of the heading in

Jan 1, 1982

By Prescott Greene

AVAILABLE MACHINES Machines discussed in this section include only rubber tire mounted kerf cutting machines of a self¬propelled electrically powered design. Such machines handle bars up to 4.6 m (15 ft) in length, cutting kerfs of from 115 to 191 mm (4.5 to 7.5 in.). The basic design concept of all machines currently in production is very similar. The chassis features dual driving wheels on the cutter-bar end, fixed directly to the main frame. The steering wheels on the outby end of the frame are articulated in some manner to keep all four wheels on the floor over uneven bottom. Machine power for tramming, and all other functions except powering the cutting chain, is furnished from a pump motor that drives the specific pump or pumps required by a given machine. The cutter chain is driven through a mechanical drive train from a separate electric motor having no duty other than driving the chain. The general arrangement of a cutting machine is shown in Fig. 1; two types of machines, with their specifications are shown in Figs. 2 through 5. A hydraulically powered cable normally is included to eliminate the need for manual cable handling and make this a one-man machine. A bug duster, though optional, is needed for most applications. The bug duster is an hydraulically driven scroll conveyor located directly behind the cutter chain drive sprocket. Its function is to move the cuttings away from the sprocket to prevent them from packing up in this area and consuming a lot of machine power to further pulverize them. Available machines vary from models 610 mm (24 in.) high that can cut horizontally only from 203 mm (8 in.) below ground line to 229 mm (9 in.) above, to machines 1143 mm (45 in.) high that can cut in any plane from 178 mm (7 in.) below the ground line to 3.7 m (12 ft) above it. Most currently manufactured machines fall in the 17 200 to 20 400 kg (38,000 to 45,000 lb) weight range, but can be dis¬assembled for underground installation where weight and size are a problem. Maximum teardown results in all pieces having a weight of 5400 kg (12,000 lb) or less and a size allowing passage through a 1.2 x 2.1-m (4x7-ft) opening. Further reduction in either size or weight of the parts becomes a serious problem. Machines currently being manufactured are avail¬able for use with power supplies of 250 v dc; 500 v dc; 440, 550, or 950 v ac (60 Hz). Also available are machines for use on 415, 500, and 950 v 50 Hz. De¬signs to allow operation on other voltages of either 50 or 60 Hz can be made available without any serious problems. As of September 1977, a typical medium-seam ma¬chine without the extra options needed for unusual conditions, but fully equipped to operate, was selling for about $185,000. CAPABILITIES Materials That Can Be Cut The problem of deciding before a machine is put on the job whether it can work effectively is an old one that has never been completely solved and probably

Jan 1, 1982

By A. J. Lynch, M. J. Lees

Introduction The design of wet grinding circuits may vary considerably according to the duty which is to be performed. Grinding machines which are commonly used in these circuits are rod mills, ball mills, autoge¬nous mills, and pebble mills while size separation machines commonly used are vibrating and wedge-wire screens, hydrocyclones, and rake classifiers. In some circuits, such as those producing feed to cement kilns, all the ore entering the circuit is discharged in a single product stream. In others, such as those operating on magnetite-taconite ores, the feed entering the circuit leaves in two or more streams. Grinding circuits in flotation plants normally include sections in which either the concentrate or the tailings from the primary flotation circuit is reground and these additional sections should be regarded as an inte¬gral part of the grinding circuit. A typical circuit is shown in Fig. 18. Problems in achieving maximum efficiency may occur at three stages: 1) At the design stage when the optimum size reduction flow¬sheet must be selected with respect to the types, numbers, and sizes of processing units. 2) At the operating stage when the correct selection of values must be made for those variables which may be altered while the circuit is off-line but which are constant while the circuit is on-line, for instance the vortex finder diameter of the cyclones. 3) Under conditions of continuous operation when changes in the circuit feed or in the mechanical operation of the circuit may cause undesirable changes in the circuit product. The first two prob¬lems are concerned with optimization, that is, with making the best choice from many possibilities, and the last with control. Optimization Problems. The main purpose of a wet grinding circuit is to produce particles with a sizing distribution which will ensure optimum performance of the later chemical reaction or physical concentration circuits, because it is on the efficiency of these later circuits that the economics of the total mineral treatment process depend. The size distribution of the product from a grinding circuit may be affected by many variables, some concerned with the arrange¬ment and operation of the machines and some concerned with the ore characteristics, and it is important that these should be recognized in the design and operation of the circuit. For instance, in a simple ball mill-cyclone circuit the variables which affect the product size even for constant feed characteristics are shown in Fig. 19. In addition, the rate, size, hardness, and mineralogical composition of the feed will affect the performance of the circuit and the product size. When the circuit contains more than one mill, both the number of choices available and the complexity of the problem are increased consider¬ably. Consequently, one type of problem which is to be solved if an optimum product is to be obtained from an existing grinding circuit is that of circuit design, and this includes arrangement of processing units and selection of those operating conditions which cannot be altered when the circuit is operating, such as mill speed and cyclone inlet and outlet dimensions. The other major problem in optimization is encountered at the design stage when a choice must be made about the type, number, and size of processing units. For instance, for a typical high-capacity size reduction operation, should two circuits each containing one rod mill and two ball mills or three circuits each containing one rod mill and one ball mill be used? Alternatively, should ball mills only be used and if so, how many, what size, and what arrangement?

Jan 1, 1985

By H. O. Seigel, John C. Robbins

Luminex is a new method of prospecting for mineral deposits based on time-resolved mineral luminescence created by an ultra-violet light source. Developed by Scintrex Ltd., Luminex detects and resolves a group of key minerals - either ore minerals themselves or, more often, accessory or pathfinder minerals for certain types of economic ore deposits. These minerals are commonly found on the earth's surface, even in areas of considerable weathering. The method extends the range of mineral deposits that are remotely detectable from the air. Tungsten, tin, molybdenum, gold, and bedded lead-zinc deposits are included. Therefore, Luminex is a natural supplement to the three classical methods of airborne geophysics. The luminescence of minerals has been known and used qualitatively in mineral exploration for many years. But there are more than 500 minerals known to be at least sometimes luminescent. Luminescence of most is unpredictable and the colors they emit may vary from locale to locale. It is, perhaps, this apparent complexity of the field that has discouraged its proper scientific scale until now. There are two basic types of luminescent minerals - intrinsic and impurity activated. In the first type, luminescence is an inherent property of the mineral in its purest form. In the latter, luminescence is due to the introduction of foreign trace elements, often in very modest amounts (ppm), into the crystal lattice. These trace elements are known as activators. There are very few intrinsic luminescent minerals commonly found in nature. Chief among these are the calcium tungstatemolybdate family, more commonly known as the scheelite-powellite family, and the uranyl minerals such as autunite and saleeite. The vast majority of other known fluorescent minerals such as fluorite, hydrozincite, and many calcites, are impurity activated - that is, they will not fluoresce in purest form. In addition to the many minerals likely to luminesce at the earth's surface under ultraviolet excitation, any prospector who has ventured out at night with a mercury lamp will know that much organic matter luminesces - for example lichens and even scorpions. Just as the eye finds difficulty in resolving the luminescence of minerals from that of organic materials, it also has its limitations at sorting out minerals from one another by their luminescent colors. Figure 1 shows, in part, the photoluminescent emission spectra of scheelite, hydrozincite, and autunite. It is clear that there is a considerable similarity in spectrum between scheelite and hydrozincite and a great deal of overlap. In fact, a small amount of molybdenum in the scheelite lattice can almost bring these two spectra into coincidence. On the other hand, the autunite emission spectrum is clearly resolved from the other two. Basis of the Method The right-hand side of Fig. 1 shows the time waveforms of decay of the photoluminescence of the same three minerals. It is apparent that the lifetimes of photoluminescence of scheelite and hydrozincite are radically different and that these two minerals, therefore, may be readily resolved through their emission lifetime characteristics. It is in the realm of time-resolved measurements (lifetime characteristics) that Scintrex has made its major advance in the Luminex method. With the exception of some work by Exxon confined to uranyl minerals, to the best of our knowledge, no systematic scientific investigation has been carried out in the field of time-resolved mineral luminescence studies other than the work of Scintrex. Scintrex's findings are that all organic materials and most commonly activated luminescent minerals have lifetimes shorter than one microsecond. In addition, only a relatively small number of minerals - among them those called key minerals, or certain ore and pathfinder minerals - have lifetimes greater than one micro-second. Scintrex is able to characterize these minerals primarily by their emission lifetimes and secondarily by their emission spectral characteristics. By a combination of these factors a mineral index is arrived at. From that, photoluminescent minerals can be resolved from one another with a high degree of probability. At least two spectral channels and two time channels - of which one can be common - are required to apply this mineral index. Ground System A portable hand-held Luminex analyzer based on a modulated mercury lamp has been used to date in Canada, the US, and Australia. The current production model of this device is the LG-2. It has two spectral channels and two time channels for each spectral channel. Figure 2 shows a ground Luminex traverse over the Texas-Arizona zinc prospect in Arizona. The instrument was set so the channel read was hydrozincite-specific insofar as possible. The mineralization in this prospect is known to be hydrozincite and other zinc secondary minerals in limestone. Figure 3 shows a ground Luminex traverse over the AAA uranium prospect in Nevada. The instrument was set to optimize the uranyl response. For comparative purposes, broadband scintillation counter readings were made on the same stations (also shown in Fig. 3). It is apparent that both the Luminex and the scintillation counter results reflect a near-surface distribution of uranyl minerals. It is interesting that no visible uranyl secondary minerals

Jan 7, 1983

By Stephen H. Stow

Economically important heavy minerals have been studied in the sediments of offshore Alabama and Mississippi. Sandy samples have been collected from a 200 square mile area from Dauphin to Horn Islands. The minerals concentrate in sediments under 10-35 feet of water and may reach 2.4% by weight. The distribution of total heavies is related to the hydrodynamics of offshore Alabama-Mississippi; the greatest concentrations are in the Gulf where the longshore current is diverted from its westerly flow. Preliminary observations indicate that the distribution of individual minerals can be correlated with wave energy, particle size, specific gravity, and morphology of the mineral grains. The coarser, lighter minerals--kyanite, sillimanite and staurolite--are concentrated in relatively low energy areas in the Mississippi Sound and at the end of Dauphin Island in the Gulf; maximum concentration for each is 34.5%, 6.0% and 43.2%, respectively, of the heavy minerals. The smaller, more denseminerals--ilmenite, rutile, leucoxene, zircon and monazite--are concentrated in high energy areas in the Gulf; maximum concentration for each, respectively, is 42.0%, 5.9%, 9.652, 10.7% and 1.3% of the heavy minerals. On the basis of a minimum concentration of 1% heavy minerals, two areas have been identified and the total amounts of different minerals have been calculated to a depth of 25 feet of sediment. The data are preliminary and in no way indicate recoverable reserves, but they do show that on the order of 20 million tons of heavies exist. These deposits should be termed "indicated resources".

Jan 1, 1975

By Charles E. Michener

This paper deals with the occurrence of basic and ultrabasic rocks and their relationship in space and time to major structures of the earth. In order to introduce the paper properly, I must go back a little and try to put the subject in perspective. In the brief time that geology has been a scientific occupation, ore deposits have been grouped and classified in various ways depending on the theories that happened to be popular at the time. Some of the early scientists said that ore came from fire, other schools argued that ore originated from water. Then came the lateral secretionists and in later years the hydrothermalists led by the Lindgren school and the latter has largely been accepted as the modern concept of ore deposits. It now seems apparent that the hydrothermal school is being seriously challenged by other schools of thought. It also seems that we have reached the point where we should be willing to admit that we do not really know in most cases how the ore got to its present position. However, for practical purposes, we can classify ore deposits as to the environment in which they do occur. This is not difficult and gives the field geologist and the mining engineer something to work with and to believe in, and it gives them a basis for carrying out their field work. On the screen, Figure 1, there is a classification of ore deposits based on the environment. Under each classification is listed the more prominent metals which are characteristic of that

Jan 1, 1971

By R. L. Russell

Production at Freeport Indonesia's Ertsberg open pit copper/gold mine started in 1972 at a rate of 7500 t/d. Mill throughput remained at that rate for a number of years until the discovery of the Ertsberg East (GBT) orebody. This discovery prompted three successive expansion stages from 1981 to 1988 that boosted production to 20,000 t/d. The discovery of the huge Grasberg porphyry copper deposit in 1988 launched a new era of much larger expansions. The first of these involved installation of a fourth primary mill in 1989 to bring production up to 32,000 t/d and was immediately followed by an expansion of the crushing and screening plant and the addition of a new south concentrator to bring production to 57,000 t/d in 1991. The addition of a primary ball mill and the changeout of the original Denver flotation cells in 1993 has served to optimize current production at a level of 66,000 t/d. A major expansion is now in progress. This includes construction of another new concentrator to house a SAG mill circuit and large Wemco flotation cells in an area created by the removal of 6,000,000t of glacial material. This current expansion, with a planned completion in 1995, will take production to 115,000 t/d. This paper describes the evolution of the Freeport Indonesia (FI) concentrator to-date and will then go into an in-depth discussion of the 66,000 and 115,000 t/d expansions.

Jan 1, 1994

By Dale E. Hirschfeld

The clays in Eastern Washington occur in a variety of forms and are extracted for uses in Face Brick, paper coatings, and aggregates. Not in large volumes in comparison to other areas, not even from impressive large mines. However, mans utilization of these clays has progressed from historical clay tablets to the present technically oriented manufactured products of today. White Face Brick, perhaps the whitest produced anywhere is the unique product produced by INTERPACE CORPORATION's Mica Plant from these unusual clays. It is this basic characteristic feature of the clay's in the Mica area that differentiate them from the other clay's in this belt. ORIGIN The significant properties of clay's used in Face Brick are plasticity, fired color, fired strength, dry and fired shrinkage, the PCE or Pyrometeric Cone Equivalent, and extrudability. Testing clay's for these properties is standard laboratory procedure. No two clays are alike, and seldom can one clay be substituted for another. Mica White Clays respond favorable to all these properties, but more especially, the Mica Clays fire to a brilliant white color, from almost the natural state. The geologic history of Eastern Washington is largely conjectural because of the absence of rocks representing segments of geologic time. The oldest rocks in this area are the argillaceous and arenaceous sedimentary rocks which have been slightly metamorphosed. These rocks have been correlated with the Belt Series of the Pre-Cambrian age, although some may be older. These rocks were subsequently intruded by granadiorites and related rocks that are considered to

Jan 1, 1971

By John W. Leonard

The typical tunnel boring machine in use on today's tunnel project uses 15'2-inch diameter cutters at a nominal load of 45 kips per cutter. The cutterhead rotates at a speed of 120 over D revolutions per minute where D is the cutterhead diameter in feet. The typical machine operates about 50 percent of the time. Delivery of a new machine takes 12 to 15 months. The TBM is a specialized tool and not applicable to all jobs. There is a range of job conditions that limit the economic use of a TBM. The machine should provide a thrust per cutter at least twice the compressive strength of rock in psi and up to three times the rock strength is required if in "granitic rocks." The rock strength in psi must be at least three times the cover above the tunnel in feet or the machine may stick. For example, 2,500 feet of cover requires at least 7,500 psi rock to avoid problems. When the RQD's over a significant distance of the project are less than 50, the TBM becomes support-bound. When a large percentage of the time is spent waiting while the ground is supported, the TBM cannot perform well (See Figure 1). This problem increased inversely with tunnel diameter. We are finding that increasing the RPM's does not significantly increase progress. The increased RPM results in a substantial decrease in cutter penetration. The explanation for this decrease appears to be vibration, cutterhead drag, or lack of stiffness in the cutterhead (See Figure 2).

Jan 1, 1981

By R. Bruce Sheibach

The Picher Mining District, located principally in north-eastern Oklahoma, was one of the world's largest lead-zinc mining areas during its 55 year life. The field covers an area of approximately 72 square miles (186 km.-); an estimated 1.6 x [103 yds3 of material (1.22 x 103m3)] worth in excess of one billion dollars, has been mined. Mining activities were typified by surface exploratory drilling identifying ore distribution and extension of underground workings to the lead and zinc deposits outlined. Exploration holes were either left unplugged or plugged at the surface with a section of a telephone pole. Low grade ore and waste rock were discarded in mined out portions of drifts. These waste piles containing pyrite and marquisette were left underground and oxidized during the many years of active mining. Upon cessation of mining activities in the mid-1960's, the drifts and shafts of the abandoned workings began to flood as the cone of depression filled in, leading to the dissolution of the oxidized sulfides and the formation of large volumes of acid mine water in the mined out openings. The resulting poor quality water, with high concentrations of cadmium, iron, lead and zinc, began discharging at the surface in 1979. Contamination of the underlying aquifer supplying local residents was first detected on a localized scale in 1980. The present surface water and ground water contamination have lead to the area being classified as one of the top ten hazardous waste sites in the U.S. by the EPA under the superfund program.

Jan 1, 1982

By Per H. Fahlstrom

The story of the Aitik mine begins in the early thirties. At that time blocks of low grade chalcopyrite impregnations were found in Swedish Lapland not far from the present mine, some 40 miles north of the arctic circle in the vicinity of the iron ore field at Gällivare. The ore prospect was viewed upon several times. By means of geophysical studies and an extensive diamond drilling programme during the end of the fifties and the beginning of the sixties a huge low grade ore body was discovered under the muskeg overburden. In 1965 55 million tons of ore with 0.5 % Cu was known to a depth of 160 ft. In 1970 the ore reserves had increased to 165 million tons with 0.40 g, Cu at a depth of 400 ft. Decision to develop the mine and to start production at an annual production of 2,2 million tons was made in 1965. A mine and concentrating plant, the A section, went on stream in 1968. In 1970 decision was made to expand the production with 3,3 million tons pr year. A second section of the plant, the B section, went on stream during the end of 1972 and the beginning of 1973 The production in the initial plant has been increased to 3,1 million tons pr year and during 1974 the combined A and B sections are expected to treat' about 7,2 million tons of ore. The two sections will treat 10,000 and 13,000 tons per day.

Jan 1, 1974

By Wern-ping Chen

To mitigate and control the combined sewer over-flows from 17 outfalls in Detroit, MI, three outfalls in Dearborn Heights, MI and eight outfalls in Redford Township MI, the Detroit Water and Sewerage Department (DWSD) completed the preliminary design of a storage tunnel in 2005. In 2006, a final design revised the alignments and the inside diameter (ID) of the tunnel. The revised tunnel system includes an 11.28-km (7-mile) 9.14-m (30-ft) ID tunnel, a 24.4-m (80-ft) ID pump station, two work shafts about 15.2-m (50-ft) ID each and 14 drop shafts with various IDs. A small portion of combined sanitary and storm sewers serve the majority of the Rouge Valley water-shed. This includes Detroit, MI and most of the western suburbs. The Northwest Interceptor (NWI), that extends between Eight Mile Road and Ford Road and roughly parallel to the Rouge River, intercepts sanitary sewage and some wet weather flows from trunk sewers in the tributary areas for transport to the wastewater treatment plant (WWTP) for treatment. During extreme storm events, when the capacity of the NWI is exceeded, the excess combined sewer and overflow (CSO) over-flows into the Rouge River through 17 outfalls to local rivers. The purpose of the Upper Rouge Tunnel system (URT) is to capture and significantly reduce the uncontrolled CSO from these 17 outfalls in Detroit, three outfalls in Dearborn Heights and eight outfalls in Redford Township. When implemented, the

Jan 1, 2007

By Greg R. Wheeler

Few members of the general public have a clear understanding of mineral resources. Most people do not know how minerals are mined or why they must be extracted from many diverse locations. Many people acquire knowledge of mineral development from mass media sources with incomplete details or obvious anti-mining bias. The California Mineral Education Foundation was formed in 1991 to provide educational opportunities for the public and industry. There have been major changes in earth science teaching requirements for kindergarten through 12th grade (K-12) curricula since the passage of California Senate Bill 813 in 1983. Model graduation standards, curriculum standards and the state science framework mandate substantial coverage of geoscience topics. The California State Commission on Teacher Credentialing has completed changes in multiple subject and single subject science credentials which will require more geoscience preparation for all teachers. The need for pre-service and in-service education in geoscience is at an all time high. Teachers must have continuing education to maintain their credentials and many are now seeking information in geoscience. The California Mineral Education Foundation designed and conducted the California Mineral Education Conferences held in August 1991 and 1992. The conferences involved lectures and field trips on mining geology, environmental problems and political concerns. Master teachers were employed to share how they get across mineral resource concepts in the classroom. Ninety-six percent of the participants stated that they had changed to a more positive perception of mining after taking the three day course.

Jan 1, 1995

By Maria S. Adusmilli, Bhaskara A. Rao, Jorge G. C. Barros, Augusto F. Mendonca

Lateritic gold has been the object of study only for a very few years, though nuggets have been mentioned in earlier works even as early as 1984 by Hartt in Brazil. In Mato Grosso State, lateritisation is intense, as is common in all tropical forest areas of the world. Exploration has revealed the presence of recoverable "nugget gold" of variable sizes (30 - 200 gms) but frequently of good size (0 - 40 gms), especially near Cuiaba and Alta Floresta regions. In both of them the host system is a lateritised breccia indicative of a fault or shear zone breccia, though in different lithological domains. The Cuiaba occurrences are phyllitic and show a profile as follows, from top to bottom: 1) Compact ferralite crust. 2) Oolitic to pisolitic compact crust (+ some gold). 3) Mottled concretionary laterite crust. 4) Lateritised "eluvial material" (gold nuggets). 5) Mottled patchy to banded laterite. 6) Banded lateritised phyllite with lenticular to banded goethite. 7) Altered red goethitic phyllite, with quartz veins (+ fine gold). 8) Unaltered grey phyllite with quartz veins (Protore). The Alta Floresta-Juruena River occurrences are volcano-sedimentary and show a profile as follows: 1) Deep brown siltitic, argillaceous and arenaceous material with organic matter (+ gold). 2) Modular and concretionary laterite, compact and indurated, with arsenophyrite in quartz fragments (gold nuggets). 3) Band with silty-clayey matrix and arenaceous in nature. 4) Bedrock meta-arcosian arenite. 5) Volcano-sedimentary with rhyodacites and andesitic basalts, with intercalations of arkosic and greywacke nature. Breccias and quartz veins, and granites associated in different portions (Protore).

Jan 1, 1988