Search Documents

By Richard E. Ray

Conventional concrete block plastered with a cemantitious coating is the most common material used in the construction of perma¬nent stoppings to direct airflow in underground mines in the U.S.A. All mines experience various degrees of strata convergence depending upon depth of overburden, geological conditions, and type of roof support employed. Strata convergence will cause cracks and joint openings in masonry stoppings, resulting in significant air leakage losses. Where strata convergence is severe, complete structural failure of the stopping can ultimately occur. Reconstruction of damaged or destroyed stoppings adds expensive overhead to mining operations, and even greater expenses are incurred from the additional fan horsepower required to overcome leakage losses. Ideally, a stopping should maintain high resistance to airflow while yielding to strata convergence. By properly incorporating "Max-Seal" polyisocyanurate rigid foam material within the masonry block structure, stopping service life can be increased several-fold in mines experiencing strata convergence problems such as floor heave, roof loading, and lateral rib movement.

Jan 1, 1984

By Angela K. Braden

Igneous rock exposures occupy only a minor portion of surface area (<18 mi2) in Arkansas, and are divided into two major groups: nepheline syenite (7 mi2) and syenite complexes (8 mi2), with various dikes and sills representing the remaining surface exposures. The syenite complexes have been the sites of major vanadium and minor titanium production during the past 50 years. Nepheline syenite exposures were important in the early production of locally used building stone; however, aggregate and roofing granules have now become the principal market for the production of nepheline syenite in Arkansas. Nepheline syenite intruded into a sequence of Paleozoic sedimentary rocks in Arkansas and is exposed in two areas: in Saline County near the town of Bauxite, and in Pulaski County at Granite Mountain, just southeast of Little Rock. Although the central Arkansas region had been investigated thoroughly for bauxite by the early 1950s, the nepheline syenite resources of the region have yet to be evaluated systematically by the state. Arkansas nepheline syenite was evaluated for its ceramic uses in 1952. Some recent industry interest has revolved around its potential use as a sand-blast abrasive. The largest exposed areas of nepheline syenite, located at Granite Mountain, currently are being mined by the Minnesota Mining & Manufacturing Company (3M) and McGeorge Contracting (Granite Mountain Quarry). 3M has been in operation since 1947 and mainly produces roofing granules. A fine powder produced by 3M during crushing that is marketed under the name Donnafill? recently has seen use as filler in self-compacting confined construction and as an additive (frit) in common brick. Since the early 1960s, Granite Mountain Quarries has produced a variety of aggregates, ranging from riprap to industrial sand, and recently constructed a computerized hot-mix-asphalt production facility. Approximately 4.5 million tons and 1.2 million tons of syenite were produced from Granite Mountain and 3M, respectively, during 1979. No production values are available after this date; however, combined production from both quarries is estimated to be at least 6 million tons annually.

Jan 1, 1999

By Ernest A. Draeger, James W. Collins

Water only cyclones, sometimes referred to as hydrocyclones, are one of the newest types of coal processing equipment. These devices have achieved wide acceptance as fine coal cleaners in the past decade. Many metallurgical coal plants employ water only cyclones to process 0.5 mm x 0 size coal. Some of these plants have as many as 40 to 50 305-mm-diam units with each unit receiving as much as 9 t/h of raw feed. The growth in the utilization of hydrocyclones is due partly to the energy shortage, partly to the general increase in over-all coal preparation, and also because of a need for a simplified fine coal (0.5 mm x 0 size) gravimetric separator. Large diameter water only cyclones are also available and in use to process feed sizes up to 32 mm in size. However, the size normally employed for cleaning 0.5 mm x 0 coal are 356 mm or 305-mm-diam for single-stage circuits. In two-stage circuits, the secondary units are normally the same diameter as the primary units or smaller, such as 203-mm-diam. By using the small diameter cyclones and treating a closely sized feed, 0.5 mm x 0 only, it has been found that the probable error or imperfection of the water only cyclones is comparable to that obtained on the same size fraction treated in a large 610-mm-diam heavy media cyclone washing 38 mm x 0. The water only cyclone can approach the efficiency of a heavy media cyclone when cleaning fine solids because it creates its own dense media by accumulating high specific gravity particles in the wide angle conical section of the cyclone. A cut-away cross sectional view of a water only cyclone is shown in Fig. 1. It is also true that when treating a wide range of sizes (38 mm x 0) in heavy media cyclones, the smaller size particles (0.5 mm x 0) separate in proportion to the split of the media through the cyclone rather than by particle density.

Jan 8, 1980

By James I. Mathis

Should an arbitrary reduction factor be applied to laboratory compressive strengths when designing pillars? The answer is, as is the main contention of Peng&apos;s article, probably not. Many factors affect the strength of the material remaining in the pillar. On the other hand, outside influences will influence the strength testing results from the lab. This is not the first article, nor the last, to discuss the discrepancy between the two strengths. As was discussed in the article, actual pillar strength is affected by several factors. The two mentioned were: • The scale effect of discontinuities. How large must the pillar be so that the increase in discontinuity count with size will not decrease the strength. • Non-uniform strengths and lithologic units within the pillar. The scale effect of discontinuities is important. What size block must be tested so that the rock mass strength is actually measured? For a highly fractured rock mass, or coal with a high cleat density, this sample may be quite small. Conversely, if an unaltered, moderately jointed, quartz monzonite was examined, the sample block would likely be very large. This is the subject of ongo¬ing research. More to the point, if the tested sample is sufficiently large to model the rock mass strength, then no reductions should be made in the lab strength based on this factor alone. Non-uniform strengths and variations in lithologic units will also affect the pillar strength. I am not an expert in coal mines, having gained my experience in hard rock metal mining. These problems, though, are commonplace. However, strength sampling for pillar strength determination involves sampling material from within the lithologic unit that will form the pillar, not from pieces of material found on the floor. In addition, this sampling should cover the entire range of strengths of the material in the pillar-hard units (such as the partings described by Peng), as well as soft units. Testing results should then be included in the pillar design. Contrary to statements in Peng&apos;s article, at least one rock mass rating system (Laubscher, 1990) allows for the compositing of strong and weak units into a design rock mass strength that can be used for pillar design.

Jan 1, 1993

By Paulo Roberto Pereira

This paper is motivated by the belief that increasing drilling and blasting costs will not necessarily bring about better digging or crushing productivity. As a matter of fact it can be counter productive as the ensuing discussion will show. In the two case studies presented herein when powder factor increased, productivity at a rope shovel and at a primary crusher decreased. Experience has shown that equipment (shovel and primary crusher) productivity increases as the powder factor increases and concurrently operating costs decrease. This is illustrated by Figure 1where the graph shows (assuming drilling costs constant) that for increases in powder factor initially operating costs might fall till a certain point and then they start to go up again. By the same token we need to understand what is the behavior of the operation’s productivity. It seems intuitive productivity goes up for increases in powder factor but when an operation reaches the point of minimum operating cost one could say that productivity reached its maximum. For continuing increases in powder factor can productivity still go up or does it go down? This paper presents two examples where the productivities of a surface coal mine and of a quarry are reduced for increases in powder factor. This indicates that these two operations could be operating to the right of their minimum operating costs and maximum productivity and therefore wasting precious drilling and blasting dollars and resources. Moreover, their productivity is following the red dotted line in Figure 1 and the question becomes can they follow the blue dotted line for increased drilling and blasting costs? The industry owes to itself to determine this minimum operating cost point and what can be done in case that the productivity goes down afterwards despite an increase in drilling and blasting costs. In other words, utilize your drilling and blasting resources correctly. In the two examples that follow single explosive loading strategies make powder factor a valid means of comparing the results of productivity as a function of powder factor. Also, external factors such as equipment operator influence are eliminated due to the long time span considered in the analysis

Jan 1, 2005

By P. W. Hynes

Tg Soda Ash has operated a shortwall mining system in the Green River, WY trona district since August 1982. The system has proven to be highly productive. In an effort to reduce the amount of relatively expensive development mining and improve mine planning flexibility, a method to mine the return air tailgate during the shortwall retreat was tested beginning in April 1987. As of June 1988, four shortwall panels had been completed using the advancing tailgate, producing more than 739 kt (815,000 st). This paper discusses the effects of the advancing tailgate on shortwall production, development mining requirements, costs, strata mechanics, and ventilation. Shortwall mining is a hybrid extraction method combining the self-advancing hydraulic roof supports from longwall mining and continuous mining machines (Fig. 1). The technique has been only marginally successful at the majority of the nearly 20 installations worldwide. At present, the face at Tg Soda Ash Inc. is the only shortwall operating in the United States and the only noncoal shortwall in existence. Despite the method&apos;s record of limited success, the staff at Tg Soda Ash determined that the conditions in its trona mine were well suited for shortwall mining. The commitment to install a shortwall was made in late 1981 and the first panel commenced in August 1982. Between that time and June 1988, about 3.33 Mt (3.67 million st) of trona have been mined with the system from 15 panels. Annual average productivities have ranged from 818 t/shift (902 st per shift) in 1982 to 1.4 kt/t shift (1591 st per shift) in 1987. Overall, the system has produced an average of 1.3 kt/ shift (1450 st per shift). In April 1987, a method of mining the return air tailgate during shortwall retreat was tested (Fig. 2). The objective was to determine if a return airway could be established and maintained by mining a series of rooms and pillars about 7.6 m (25 ft) past the face support line. The method would allow a barrier pillar to be left between shortwall panels without requiring the mining of a separate return air tailgate.

Jan 1, 1990

By Scott Horton

In no Confederation of Independent States (CIS) country does the mining sector play quite so commanding a role as in the mountainous Central Asian republic of Kyrgyzstan. Its president, Askar Akayev, says he would like to develop his country into "a Central Asian Switzerland." However, in Switzerland, the gold is largely under the street along Zurich&apos;s renowned Bahnhofstrasse. In Kyrgyzstan, though, the gold is still in the mountains. Accordingly, Kyrgyzstan&apos;s recent adoption of a comprehensive new mining law has attracted widespread attention. Akayev recently completed a tour of the United States. His visit drew large crowds from the business community at events staged in New York and Washington, DC. The success can be attributed as much to the attractiveness of Kyrgyzstan&apos;s min¬ing sector as to the personal charms of the nation&apos;s president. Led by a half-billion-dollar investment by Canada&apos;s uranium giant Cameco, the mining sector is leading Kyrgyzstan&apos;s economic revival. And Bishkek is beginning to show some of the same signs of a "boom town" that already mark its Kazak neighbor, Almaty. Mercedes and BMWs already outnumber the Volgas on Bishkek&apos;s major traffic arteries. After nearly two years of debates involving government advisors and a final round of deliberation in Parliament, Kyrgyzstan finally adopted its second mining law. This followed quickly in the wake of measures enacted in neighboring Kazakstan and proposed in Russia. Kyrgyzstan&apos;s new law replaces the 1992 law "On Mineral Resources." It was one of the first enactments of an independent Kyrgyzstan. The 1992 law made a major contribution to the introduction of free-market economics in the country by ending the state monopoly over mineral exploration and development. It also laid the groundwork for an independent mining industry. According to Kyrgyz government reports, Kyrgyzstan has about 270 commercially viable deposits of almost 40 types of mineral resources. These include oil, gas, coal, precious-, nonferrous-, ferrous-, rare- and basemetals. However, the nation&apos;s key draw is gold. Since enactment of the first law, the government has issued more than 100 licenses for geological prospecting for and development of established deposits of gold.

Jan 1, 1998

By H. Beecher (Original by) Charmbury

Water is a most remarkable substance, essential for life of all kinds. As well as needing water to survive, man has always used it for agriculture, transportation, recreation, and many other things. When our country was young and inhabited by few people, the streams, rivers, and lakes were able to provide all the clean water needed by man and take away all the wastes created. However, with our growing population and an ever-increasing demand for goods and services, the public, industry, and government at all levels have become acutely aware of the need to manage the nation&apos;s water resources more efficiently. Abundant energy from many sources has helped this nation to become the greatest industrial nation in the world. Coal has contributed a major portion of this energy, generating electricity, running railroads, and maintaining national security during wartime. The result has been the highest standard of living in the world and a time of widespread economic prosperity. The use of water in coal mining is somewhat different from its use in most industries. With the exception of water used in cleaning plants, for underground dust control, and for fire protection, most of the water en- countered in coal mining operations serves no useful purpose. In other words, it is an undesirable element and must be removed, otherwise it will interfere with operations, cause potential water quality problems, and may even stop operations by flooding. In the past, removing water from working areas of most mines was usually a fairly simple matter. Pumps with piping were installed at sumps or low spots in the mine and the water was pumped to the surface or to drainage control facilities constructed for the operation. Ditches were often used to collect and drain the water by gravity to the outside or to main sumps for pump discharge. In either case, the water was allowed to flow into the nearest stream or river. The concept of "water is water&apos; was generally accepted without too much concern for what was in the water since low-cost products and services, rather than clean water, were the public demand.

Jan 1, 1981

By Daniel H. Stevenson

Safety and health are fundamental values at Barrick Goldstrike. An effective safety and health program protects employees, controls costs and increases productivity. Barrick Goldstrike believes that all occupational injuries and illnesses can be prevented and that safety must be the responsibility of every employee on the property. Safety and health must be thoroughly integrated with the company&apos;s efforts to maximize production at the lowest reasonable cost. The goals of safety and production are not mutually exclusive. They must work together to achieve safe production. Barrick Goldstrike began to mine the Betze deposit in 1987. From 1987 to 1992, Barrick employed a traditional safety system using safety specialists on each crew. These specialists were responsible for ensuring that the work areas were safe and that employees were properly protected and trained in safe work procedures. As the work force increased, it became apparent that this system was not the most effective method of ensuring safe production. In 1992, Barrick Goldstrike implemented a loss control program. It was modeled after the International Loss Control Institutes&apos;s (ILCI) International Mine Safety Rating System. This program was based on the philosophy that safety is a management responsibility. It can be managed in the same manner that production and cost issues are managed. Under the loss control system, safety needs are identified and evaluated. Programs with performance standards are developed and implemented and the activities and results are regularly monitored. Between 1992 and 1996, Barrick Goldstrike worked at developing and improving its safety management systems. These efforts had a positive return. The incident rates began to decline as these improved systems were implemented. Studies were undertaken in early 1996 to evaluate the effectiveness of the safety and loss control programs in reducing accidents. The studies showed a strong correlation between the implementation of the loss control programs and the resulting reduction in all accidents. Studies in the process division revealed that Barrick had experienced reductions in personal injury accidents from the projected number that could have been expected had no changes been instituted. These reductions ranged from 39% in 1993 to 59% in 1995. These reductions from the projected rates held true for all types of accidents; personal injury, property damage and Mine Safety and Health Administration (MSHA) reportable.

Jan 1, 1997

By Deborah Shields

Aggregate is an essential input to every economy, so governments need to ensure a sustainable supply of these resources through planning. There is also a need to shift from a linear economy to a more circular one, in which wastes are recycled rather than landfilled, so as to increase eco-efficiency. The purpose of the Sustainable Aggregates Planning in South East Europe (SNAP-SEE, SEE/D/0167/2.4/X) project is to develop a Toolbox for Aggregates Planning to assist governments and stakeholders in national, regional, primary and secondary, aggregates planning in southeast European countries. The Toolbox comprises documents on stakeholder consultation, data and analysis methodologies, a vision of best practices in aggregates planning and how to build an aggregates plan. The Toolbox will also support ongoing efforts to enhance minerals policy in the European Union (EU) as called for by the European Innovation Partnership on Raw Materials. Industrialized and developing nations see long-term and continued economic growth as essential to the well-being

I reached New York at the start of my second South American adventure on Jan. 9, 1916. In the Anaconda office I found that we were not to take the steamer for two weeks which gave me time to study reports on Potrerillos and Corocoro. Reno Sales, whom I had met in Butte only casually, was to go with us to South America. Though he was only a little older than I, he was already an unquestioned leader of our profession, and we became and remained good friends. William Braden was in New York and would return to Santiago with us. Tom Hamilton would also be returning from a vacation. Leighton Stewart, a young engineer who was to work for Braden, was going on the steamer with us, taking along his wife. And of course Dr. Ricketts would go along. He had just become engaged to John Greenway&apos;s half sister, Kate Greenway, and in order not to be away from her longer than was necessary, he did not reach New York until a day before we sailed. This made eight of us who would be in the party. We were to go to Corocoro first, as Braden had taken an option on the Chilean company there. Development was already under way. As reports came in by mail we tried to get as good an idea of the property as we could before the actual examination. Mr. Thayer "put us up" at India House, one of the best lunch clubs in New York, and Reno and I ate our lunches there almost every day. Thayer, Braden, and Cornelius Kelley, who was to succeed Mr. Ryan as president of Anaconda, joined us when they could. At the lunches they told us about the under- ground war in Butte a few years earlier. When I wrote my chapter on the Butte wars in Romantic Copper more than 15 years later I could not help being biased a bit by my friends, all of whom were on the Anaconda side. But their opponents in the Clark and Heinze camp were just as biased in their comments on my book.

Jan 1, 1976

By James E. Gingrich

The new Track Etch* technique for uranium exploration has been utilized in several survey programs conducted during the last few years. The results from these programs have been very encouraging, and new uranium ore bodies have been discovered by using this new technique. The Track Etch method is being used in several exploration programs in various locations around the world. The Track Etch exploration technique utilizes small pieces of special radiation-sensitive plastic film to detect the presence of radon gas which is released by uranium ore bodies. Because of the selectivity and sensitivity of the technique, ore bodies not normally detected with other surface or airborne monitoring methods are found. Since no large equipment or special training of personnel is needed, the Track Etch technique is easily used in field operations. The basis for the Track Etch method, its application in field exploration programs, and the results obtained to date in locating uranium ore bodies is discussed.

Jan 1, 1974

By R. Asmatulu

According to Darcy&apos;s law, the rate of filtration should increase with increasing pressure drop across a filter cake. In centrifugal filtration, the driving pressure is created by the centrifugal forces applied in the free water on the surface of a filter cake. However, the pressure drop can become negative when the free water surface disappears, which makes it difficult to achieve low cake moistures. In hyperbaric centrifugal filtration, this problem is overcome using air pressure to restore the pressure differential. In the present work, various mineral and coal fines have been subjected to hyperbaric centrifugal filtration tests. The laboratory tests show that the moistures of various mineral fines, such as copper and zinc concentrates, phosphate, talc, kaolin clay, and precipitated calcium carbonate, can be reduced substantially below that achieved by conventional centrifuges. Similar promising results have also been obtained with various coal fines in laboratory and pilot-scale test programs and in full-scale plant demonstrations.

Jan 1, 2012

By C. C. Huang

Rare earth compounds, such as samarium-cobalt compounds and neodymium-icon compounds, are being used more often for the manufacture of permanent magnets, because these materials permit the production of permanent magnets with higher magnetic energy potential than the conventional ferrite magnets. Especially, the recent rapid developments in the field of electronics and electro-technology have demanded an increased production of rare earth magnets. Unlike ferrite, which is typically produced by a wet process, rare earths can be ground and classified either in a wet or dry process. In the past, batch ball mills, through-pass ball mills in circuit with air classifiers, and conventional jet mills were primarily employed for the dry processing. These methods, however, have suffered from the problems, for example, wear and contamination, low product quality In particle size distribution, difficult to adopt inert-gas operation, and high specific energy consumption. In this report, dry processing of rare earth powders will be presented, especially ultrafine grinding with fluidized bed jet mill.

Jan 1, 1993

By Ralph L. Merklin

One of the most commonly employed set of calculations in mill design and research is the material balance, known in wet beneficiation plants, as an Ore and Water Balance. For mill designers, the balance is one of the principal requirements in determining the proper size of launders, pipelines, process equipment, etc. In process development, one of the major goals is the establishment of an optimum balance. The usual procedure for calculating a material balance involves a manual technique utilizing reference tables, pre -obtained data, and a slide rule or desk calculator. With these, the engineer must perform a series of calculations which are repetitious in nature and time consuming. Figure I is the flowsheet of the grinding and flotation circuits for a copper concentrator. The initial ore and water balance was calculated manually and required approximately 24 manhours. Later, a number of changes were made in the balance, each of which required an average of 8 manhours.

Jan 1, 1967

By RENE GOMEZ, RAUL CASTRO

Estimation tools and models are now available to estimate fragmentation, but some variables have yet to be studied to understand their effect on the fragmentation process. One such variable whose mechanisms have yet to be studied is the residence time, which in block caving directly depends on the distance that fragments travel from their original position in the broken ore to the drawpoint. In this study, granular material fragmentation was characterized during its flow to understand its characteristics and mechanisms. The results show that the breakage of fragment singularities occurred mainly within medium and smaller sizes, increasing fine material during flow. Thus, the main fragmentation mechanism in experiments was identified as abrasion between rock fragments where fine material continuously increases as distance increases in spite of the high rock strength and the piston flow movement used. The results presented here can be applied to incorporate fragmentation during flow of large travel distance of ore such as in block caving.

By C. Caceres

Fibre reinforced shotcrete in combination with other types of support systems is becoming the leading support method for underground excavations, especially those present in low quality rock masses. Sudden or rapid ground support failure can expose workers to safety hazards, damage to equipment and others resulting in production interruptions that will impact the cost of operation. Knowing the peak and post-peak strength characteristics of the support system over time are of major importance. Round Determinate Panel Testing of fiber reinforce shotcrete is the primary test used by the mining industry to determine strength characteristics; however, the tests are costly and significant manpower is required in a mine environment to build, store, handle and test the panels. For these reasons numerical modeling can result in an effective method to produce realistic results. This paper examines the strength characteristics Round Determinate Panel tests and its ultimate application in underground excavations, using Itasca?s three dimensional particle flow code (PFC3D).

Jan 1, 2010

By Harland E. Cofer

A computer-assisted resources and sedimentological study of the Andersonville, Georgia kaolin-bauxite district was begun in 1975 under a grant from the Office of Mineral Resources of the U.S. Geological Survey (Grant # 14-08-1110-G-173). A preliminary report on the kaolin and bauxite resources of the district has been placed on open file at the U.S.G.S. in Reston, Virginia; the Georgia-Geological Survey in Atlanta, Georgia; and Georgia Southwestern College in Americus, Georgia. In addition to a resources estimate, the objectives include the determination of the mineralogical variation, sedimentological parameters, and paleogeographic patterns of the deposition of the high alumina materials and their associated sediments. In the process of compiling data for the resources estimate, isopach maps were developed that provide information as to the shape, size, and distribution of the kaolin deposits and the kaolinitic sediments that contain them. These or similar maps developed for other districts can be useful exploration tools.

Jan 1, 1977

By Denise Crocce Romano Espinosa, JUNIOR AMILTON BARBOSA BOTELHO, Jorge Alberto Soares Tenorio

Bauxite ore is used to produce alumina in the Bayer process. For each tonne of alumina produced, around 1 to 1.5 t of bauxite residue is generated, with an estimated 4 Mt of the residue generated worldwide in 2015, four times more in 1985. The residue is currently stocked in tailings dams. A new step in the Bayer process has been used to recover sodium hydroxide, which is used as a leaching agent, and reduce its content in the residue. After digestion, the residue is separated from the Bayer liquor and passed through press filters. This bauxite residue is known as a source of scandium. Characterization of the residue is an important step to map opportunities worldwide. For this reason, the goal of the present study was to characterize the bauxite residue and evaluate the challenges for scandium recovery. The scandium content was found to be 43 g/t, which makes this bauxite residue attractive for extraction purposes.

By Thon T. Gin

The lithologic, mineralogic, and magnetic beneficiation characteristics of the iron formation at U. S. Steel&apos;s Atlantic City Ore Mine, Fremont County, Wyoming, have been determined. The iron formation averages about 30 percent Fe content, and varies from 125 feet to about 500 feet in thickness. It is composed of interbedded magnetite-rich quartzites, magnetite-quartz-amphibole schists, and amphibole-chlorite schists. Quartz, actinolite-tremolite, chlorite, and magnetite are the essential mineral constituents. These rocks are differentiated into four major ore types on the basis of their relative quartz and amphibole content. The iron content of the magnetic concentrate decreases and the silica content increases with decreasing grain size and increasing amphibole content in each ore type at the same fineness of grind. Criteria were developed to enable the mine operator to recognize the ore types and to blend them to produce a more uniform concentrator feed. This results in less variation in product quality and requires fewer changes in operating conditions-in the concentrator.

Jan 1, 1965