Search Documents

By E. G. Hoover

In the mid-I 970s the rallying cry sent out by the aggregate trade associations to aggregate operators was to come to Washington and help design national legislation mandating reclamation of pits and quarries. This collective effort paid off in that aggregate operators were able to assist in the design of "livable" legislation; however, the coal mining industry took some very hard hits. A principal argument used by the aggregate industry was that relatively small parcels of land are impacted, the operations are located in or near urban areas to serve in the development of that immediate area, and are of many years duration; whereas, coal strip mines disturb many acres, are of short duration, and whose products may have world or nationwide utilization. Historically, developments in reclamation are tied closely to the regulatory systems that have been created to control environmental effects of mining. Since reclamation generally results in a cost incurred after the stone, sand and gravel has been mined and does not add to the inherent value of the mineral, there was little incentive in the past for mine operators to reclaim the land. In 1977, the Surface Mining Control and Reclamation Act (SMCRA) became the law for coal mine operators. The law states that, among other provisions, reclamation must "restore the land affected to a condition capable of supporting the uses which it was capable of supporting prior to any mining, or higher or better uses". It is of interest to note that years before the initiation of legislation leading to SMCRA twenty-eight states already had reclamation regulations that covered virtually all minerals. The scope of performance standards found in the state reclamation regulations included slope stabilization, grading, revegetation, neutralization of toxic materials, visual screening, waste disposal, control of drainage, and other sources of pollution and erosion. Environmental legislation and the consequent regulations came about because the public perceived that private industry did not properly value environmental quality and as a result the government became the policeman.

Jan 1, 1998

By Faruk Oksuz, Dave Schiemann, Miguel Sanchez, Patrick Jensen

"The McCook Main Tunnel connects Chicago’s Tunnel and Reservoir Plan (TARP) Mainstream Tunnel to the McCook Reservoir. The tunnel system consists of a 10 m (33 ft) finished diameter and 490-m (1,600-ft) long hard-rock tunnel constructed from a 27.5-m (90-ft) diameter and 92 m (300 ft) deep main gate shaft. The gate shaft houses six high-head 4.4 x 9 m (14.5 x 29.5 ft) wheel gates installed in the bifurcated and steel-lined section of the tunnel. The tunnel also includes portal and energy dissipation structures as it daylights into the reservoir. Construction of the McCook Main Tunnel in live flow conditions was a challenging task for the McCook Main Tunnel Project participants, the project owner U.S. Army Corps of Engineers (USACE), local sponsor Metropolitan Water Reclamation District (MWRD) of Greater Chicago, designer Black & Veatch and contractor Kiewit Infrastructure Co. (Kiewit). Once completed in two stages in 2017 and 2029, the McCook Reservoir will hold 38 billion L (10 billion gal) of combined sewer overflows (CSO) and flood waters from the city of Chicago and 36 surrounding communities in Cook County, IL The construction of the tunnel system was divided into two contracts. The first contract for the gate and construction access shaft was completed in August 2011. The second contract included tunnel excavation and concrete and steel lining that was completed in September 2014; installation of gates and hydraulic cylinders that was completed in June 2017; and the last major construction activity was the removal of a temporary concrete plug (bulkhead) and lining that tunnel section to bring the overall tunnel and gates system online before Dec. 31, 2017.This article focuses on the installation, testing and commissioning of the high head wheel gates. Live tunnel connection details to TARP Mainstream Tunnel were addressed in a previous paper submitted at the World Tunneling Conference in 2016."

Mar 1, 2019

By William Gleason

At 6,898 ft below surface, the historic No. 9 shaft at Resolution Copper near Superior, AZ is now the second deepest single lift mine shaft in the United States and connects to the deepest single lift mine shaft in the U.S., Resolution Copper’s No. 10 Shaft (6,989 feet). The shafts serve as ventilation and access for future underground development of what could one day become one of the most significant copper mines in the United States. It is from the base of No. 9 and No. 10 shafts that hundreds of employees of Resolution Copper, a joint venture of Rio Tinto and BHP, hope will soon be given the go ahead to begin driving lateral tunnels to reach a copper deposit that is estimated to contain 28 Mt or 40 billion pounds of copper. Copper was recently added to the U.S. Geological Survey’s (UGGS) critical minerals list, in large part because of increasing demand. A study by S&P Global Energy & Market Intelligence “Copper in the age of AI: Challenges of electrification” released on Jan. 8, 2025, “identifies a transformative trajectory for copper demand, projecting a surge from 28 Mt (31 million st) in 2025 to 42 Mt (46.3 million st) by 2040 – a 50 percent increase that underscores the metal's pivotal role in multiple technological and economic domains.” The surge in demand is driven in large part by the global energy transition, electrification of vehicles, growth of artificial intelligence and data centers, and most recently robotics. Meanwhile, geopolitical tensions have increased the focus on the need for the United States to secure more of its own mineral supply chain. S&P Global’s report is one of many warnings that while copper demand has accelerated rapidly, future supply is being held back. Resolution Copper stands out as one example of a known mineral deposit remaining locked in the United States’ complex and lengthy permitting slog.

Feb 1, 2026

By Jürgen Kretschmann

Principally, mining natural resources is a finite business that reaches its limits once the deposits mined are depleted, the resources can no longer be mined in an economically profitable way or substitutes are pushing the mined products out of the market. An example of the latter is the increasing replacement of coal with natural gas and renewables in power generation in the United States [1]. According to the model of the product lifecycle, the global hard-coal mining industry has reached a stagnation phase [2]. The trend is obvious. Coal use peaked in 2013 [3], and the coal demand of China has been slowly decreasing since then [4]. Coal consumption in the United States saw a 16 percent decline from 726 Mt (800 million st) to 608 Mt (670 million st) between 2015 and 2019. In addition, according to the U.S. Energy Information Administration, it will not rise again [5]. The decline is attributed to complex market dynamics, from low gas prices because of the “shale gas revolution” [6] to federal environmental regulations like the Clean Power Plan. Moreover, important players like the United Nations and the European Union have already begun to describe pathways toward decarbonization. Increasing competition between coal-mining companies and the mining regions can be expected worldwide if companies want to keep their positions on the global and national coal markets. Companies will focus on the best deposits. European countries, like France, Spain or Germany, are only forerunners of this development — their centuries of coal production have passed. The concept of sustainable development (SD) is fundamentally based on a model of progress in which ecological, economic and social dimensions should be developed equally and positively. Questions arise, such as: How can SD be a corporate goal in a phase of decline? How can former mining regions sustainably progress to a better future? The steps Germany has taken to handle the coal decline in a sustainable way and the lessons learned from this process are described in this paper. 

By Brandon Barnes, Michael Haggerty

"Around Minneapolis and Saint Paul, Minnesota, the local geology includes the St. Peter Sandstone, which is easily minable and has facilitated construction of interceptor tunnels for storm water and sanitary tunnels since the 1800s. The elevation of the geologic units allowed gravity-driven flows from the downtown areas all the way to the Mississippi River. Through many years of service, some of these tunnels have experienced degradation and require maintenance. Additionally, increased stormwater surface runoff can result in internal pressurization of the tunnels, accelerating degradation. Because structural failure or collapse of any of these interceptor tunnels would create a significant repair challenge, the city of Minneapolis has been inspecting and designating tunnels in its system for periodic review and repair. One of these, the St. Mary’s/Hiawatha tunnel, was rehabilitated using a grouting program. A hydrologic model was also used to improve understanding of pressurization events during some storms, leading to construction of a near-surface pressure dissipation chamber to provide increased hydraulic capacity. BACKGROUND The St. Mary’s/Hiawatha tunnel in Minneapolis has three segments; the first two were constructed in 1942 and the third was added in 1987 (Figure 1). Segment 1 is approximately 4,700 feet in length and outlets to the Mississippi River. Segment 2 intersects Segment 1 approximately 3,500 feet upstream of the river outlet and continues for approximately 2,500 feet in a southeasterly direction. The third and newest segment is approximately 500 feet long. There are four different cross sections of tunnel along the entire system.Originally, tunnel construction often consisted of mining the St. Peter sandstone with a pressurized water lance and constructing wood lagging support (Payne, 1967). An underdrain was generally installed below the invert during construction; this resulted in localized dewatering and provided groundwater control during construction. Non-reinforced concrete liner sections were cast in place. Often void space existed between the tunnel liner and the native sandstone bedrock. These voids, particularly in the crown, prevent direct contact between the liner and the bedrock."

Jan 1, 2016

By J. Stowe

"While there has been continual improvement in the models for predicting deposition velocity and pipeline friction losses, the fundamental design philosophy for tailings pipelines has remained the same over the previous three or four decades: design the tailings pipeline to operate in turbulent flow without a deposit on the pipe invert for all expected process conditions. Recent improvements in the understanding of slurry pipeline flows allows for the design of pipelines operating with a deposit on the pipe invert, allowing the system to operate at moderate velocities for high flow rates, optimizing system energy requirements and maximizing pipeline wear life.Tailings pipelines are increasingly operated at higher solids concentrations when there is a greater likelihood the pipeline will operate in laminar flow due to the higher tailings slurry rheology. Historically, slurry pipelines have been operated in turbulent flow. We now know that laminar-flow pipeline operation is possible as there are several operational laminar-flow tailings pipelines. While our understanding of laminar-flow slurry pipelines is not complete, recent research provides guidance on how to approach the design of these pipelines.New sensor technology has led to the development of an instrument that provides reliable indication of bed-deposit height within a pipeline. This technology is particularly helpful in operating pipelines with a deposit and has application in better understanding the operation of laminar-flow pipelines. Failure of tailings pipelines can result in consequent damage to surrounding structures and unacceptable spillage into the environment. Modern pipeline leak detection technology allows operators to better manage this risk by ensuring safe and reliable operation of tailings pipelines.This article provides an overview of the each of the above advances in the design and operation of tailings pipelines.Operating tailings pipelines with a depositTailings pipelines, and slurry pipelines in general, are typically designed to operate without a deposit on the pipeline invert. Meaning, the minimum operating velocity exceeds the turbulent deposition velocity. This approach has been adopted due to concerns regarding potential blockage of a pipeline operating with a deposit."

Jun 1, 2019

By Calvin R. Davis

The bucket elevator is probably the oldest known form of conveyor. Its history can be traced back to the days of Babylon where wicker baskets lined with a natural pitch and fastened to ropes operating over wooden sheaves turned by slaves, were used for the elevating of water into irrigation ditches. It is not unnatural for the bucket elevator to be the first in history, for even today engineers and designers recognize that well designed, correctly applied bucket elevators offer unequaled advantages over other bulk material elevating methods. The bucket elevator's vertical design saves valuable floor space. It provides flexibility of machinery layout with lowest initial capital expenditure, which is its principal advantage. While the advantages of the bucket elevator have long been recognized, there has been a tendency to lean away from its use because of high maintenance without reliability. CHAIN Belt Company found that the bucket elevator, if correctly applied, can be built to be as dependable and reliable as any other piece of machinery in today's modern processing plants. It is not difficult to understand why the bucket elevator is looked upon sometimes as a necessary evil in the material handling system. Very little has been published or written about the specific use or application of bucket elevators other than in manufacturers catalogs. Most of today's elevator application was set forth at the turn of the century by Hetzel (1). There have been many improvements made in the manufacturing techniques of elevator components, improvements in material selections, all which can be used to improve today's bucket elevator. To best understand the improvements which have taken place recently in the design and application of bucket elevators, an understanding of basic elevator principles is desirable. In general, it can be said that bucket elevators are classified into two basic types : (1) centrifugal discharge and (2) continuous. Elevators in use today are either of the centrifugal discharge type or the continuous type, or a combination of both in special applications.

Jan 1, 1958

By Thomas Jancic

Two of the open-pit, copper-molybdenum mining operations of Duval Corporation are located in the foothills of the Sierrita Mountains approximately 30 miles southwest of Tucson, Arizona. In March 1959, mining from a moderate sized porphyry deposit known as the "Esperanza orebody" was begun at a rate of 10,000 tons of ore per day. Some five years later, a sizeable group of mineral claims west of Esperanza became available to Duval. Earlier exploration and development drilling in this area by others indicated an orebody of greater size but lower tenor than that of Esperanza. A drilling program conducted by Duval not only verified the results of the prior drilling but in addition, revealed a continuation of the mineralization to the south and east. Thus was developed the Sierrita orebody. Open pit design delineated 414 million tons of ore containing an average copper content of 0.35 percent and a molybdenum content of 0.036 percent. In April 1966, the office of Emergency Planning authorized General Services Administration to undertake a program under the Defense Production Act to en¬courage additional domestic production of copper in the interest of national defense. Duval's Sierrita Project was brought to GSA's attention in May 1966 on November 28, 1967, an agreement providing for the development of the Sierrita Property was consummated with GSA. In March 1970, the first copper-molybdenum concentrates were produced in the 72,000 tons-per-day concentrator. Pre-production stripping exceeded the scheduled 105 million tons despite the comparatively short lead time available to equip the mine, build the mine plant facilities, and staff the technical, supervisory, and labor forces. Shortly before the first concentrates were produced, plans were being formulated for a program to increase processing capacity by approximately 15 percent, which entailed increasing overall mining capacity by approximately 50,000 tons per day. This program is scheduled for completion early in 1971.

Jan 1, 1971

By William Gleason

The Society for Mining Metallurgy and Exploration (SME) has a long and proud history of being the world?s leading resource for the dissemination for technical information regarding the fields of mining and mineral extraction and processing. That reputation was met, and maybe even exceeded, with the programming for the Society?s 2014 Annual Meeting in Salt Lake City, UT Feb. 23-26. The meeting drew more than 6,700 attendees to the three-day conference that featured more than 90 technical sessions with 670 presentations. These sessions covered the breadth of the mining and minerals industry, but it was the so-called ?softer issues? that were discussed in the keynote session that kicked off the meeting. The keynote session, ?Community Engagement: Building Partnerships for Mining,? brought together some of the leading voices from the mining industry, as well as some of the top voices from nongovernmental organizations (NGOs) that work in the mining sector. The common ground between the panelists was their dedication to working to ensure a social, economic and environmental balance in the development of mines. ?We wanted to bring these NGOs in to begin a dialogue to see how we can work together,? said SME President Jessica Kogel. ?This is a space that SME has not typically operated in, but one in which SME can bring a technical, scientific voice to the discussion. SME wants to play a leadership role in creating partnerships between the technical, social and economic areas that are crucial to the success of any mining project.? In today?s environment, finding mineral deposits and extracting the minerals in an economically viable manner is just one piece of an increasingly complex puzzle. Earning and maintaining a social license to operate requires careful consideration of local and global impacts. The industry often comes under intense scrutiny when a new project is proposed and, therefore, it must strive to meet the highest ethical and environmental standards. Success requires cooperation and collaboration between the industry, community and NGOs.

By Chee S. Theng

As the 2018 president of the Society for Mining, Metallurgy & Exploration Inc., I am pleased to present the 2018 issue of the Transactions of the Society for Mining, Metallurgy & Exploration Inc., Vol. 344. A significant portion of the contribution that we make as a professional society is the publication of professional and technical papers that accelerate the advancement of scientific knowledge and enable the transfer of technology. Communication within the mining community is the key to a successful society. This technology exchange continues a tradition that dates back to the 1871 meeting of 22 mining engineers in Wilkes-Barre, PA, that resulted in the founding of the American Institute of Mining, Metallurgical and Petroleum Engineers (AIME). Those individuals envisioned that these transaction volumes “would form a most valuable and greatly needed addition to our professional literature.” This volume fulfills that pledge. The 2018 Transactions consists of a total of 59 technical papers, encompassing all 25 papers published in 2018 in the Technical Papers Section of Mining Engineering (Vol. 70) and all 26 papers published in 2018 in Minerals & Metallurgical Processing (Vol. 35). Additionally, this volume contains 8 papers that are being published for the first time in this issue. The papers presented in this volume were written by some of the most distinguished professionals in the industry worldwide. All of the technical papers were peer-reviewed. The process of review and publication requires much hard work by authors, reviewers and our Publications staff. As the 2018 president of SME and on behalf of all our members, I would like to extend our gratitude to all whose volunteer efforts contributed to the publication of this volume. The new year brings an exciting change. The publication of Transactions will cease with this volume. Instead, our Minerals & Metallurgical Processing journal has the new name of Mining, Metallurgy & Exploration (MME), and Transactions as well as the Technical Papers Section of Mining Engineering are incorporated into MME. The journal is published in partnership with Springer Nature, and all SME members have free electronic access to the journal.

Jan 1, 2018

By L. Patts, J. Hummer

The use of diesel-powered equipment in underground coal mines has increased substantially during the last ten years in an effort to enhance mine safety and productivity. Pennsylvania and West Virginia are two of a number of states with regulations governing the use of such equipment. These states both developed and promulgated regulations before permitting diesel equipment in their underground coal mines because of concern for miners’ safety and health, especially with regard to the contamination of mine ventilation air with diesel exhaust emissions. The major components of diesel exhaust emissions are combustion gases and diesel particulate matter. The gaseous emissions consist of carbon monoxide, carbon dioxide, oxides of nitrogen, sulfur oxides and unburned hydrocarbons. The diesel particulate matter (DPM) is comprised of solid carbon particles, liquid and solid hydrocarbons, sulfates and moisture. The Federal Mine Safety and Health Administration (MSHA) also promulgated regulations in an effort to control diesel emissions in underground coal mines. MSHA has adopted threshold limit values (TLVs) for all gaseous components of diesel exhaust, which were established by the American Conference of Governmental Industrial Hygienists (ACGIH). MSHA (30 CFR Part 72 Subpart D) has established a tailpipe DPM emissions limit of 2.5 g/hr for diesel engines used in permissible equipment, heavy-duty non-permissible equipment, generators and compressors used in underground coal mines. A tailpipe DPM limit of 5.0 g/hr has been established for light-duty outby diesel-powered equipment. The rationale for the tailpipe emissions limit was that an ambient measurement of DPM in a coal mine was not feasible because there is no established sampling method able to distinguish between coal mine dust and DPM. The stringent tailpipe emissions limit mandates the use of exhaust aftertreatment devices for most diesel engines used in underground coal mines today. One method by which tailpipe DPM can be reduced to MSHA limits involves using an exhaust cooling device in conjunction with a high-temperature, disposable diesel particulate filter.

Jan 1, 2011

By S. A. McGhee

Introduction ASARCO's Ray Operations include an open-pit copper mine in the Mineral Creek Mining District of Pinel County. The district is located in east central Arizona, 132 km (82 miles) southeast of Phoenix, AZ, and 126 km (78 miles) north of Tucson, AZ. The mine lies 8 km (5 miles) north of the Gila River in Mineral Creek Valley, between the Tortilla Mountains to the west and the Dripping Springs Range to the east. The rich copper deposits of the Mineral Creek mining district were first noted by a US Army Officer in 1847. The Ray Copper Company was the first major operation in the area. The company was named after the Ray mining claim, which was one of the earliest recorded claims. After decades of sporadic and unsuccessful mining ventures, the Ray Consolidated Mining Company was formed in 1910. The company introduced one of the first successful block caving operations in the world. In 1933, the Kennecott Copper Corporation acquired the Ray Consolidated Mining Company and continued operation of the mine under the same name until 1943, when the property was renamed the Ray Mines Division of Kennecott. Underground mining continued until 1955, when the mine was converted to an open pit operation. In November 1986, ASARCO Inc. purchased the Ray Mines Division and related facilities from Kennecott. The purchase also included the Hayden concentrator and the Ray Smelter, located approximately 32 km (20 miles) from the Ray Mine. This paper summarizes the 54,400 tpd (60,000 stpd) in-pit crusher and overland-conveying system and the 24,200 tpd (30.000 stpd) copper SAG concentrator and tailings disposal system constructed at ASARCO's Ray Complex - Ray Operations. General description of facilities The Ray concentrator includes a sulfide SAG concentrator, a "relocatable" in-pit primary-crushing plant and overland-conveyor system, a concentrator tailings-disposal system and plant ancillary facilities, The major elements of the project include: • A relocatable Fuller-Traylor in-pit 1524-mm (60-in) x 2261-mm (89-in) primary gyratory crusher at the 442 m (1450 ft) mine elevation. The crushing plant has a nominal capacity of 54,400 tpd (60,000 stpd) of sulfide ore. • A 1524-mm (60-in) wide x 1253-m (4110-ft) long overland belt conveyor, which runs from the in-pit crushing facility to a transfer station serving both the Ray Concentrator and the existing Hayden concentrator railroad load-out facility. • A 1524-mm (60-in) wide x 152-m (500-ft) long stackerbelt conveyor, which delivers a nominal 27,200 tpd (30,000 stpd) of ore from the transfer station to a 23,600 t (26,000 st) live-capacity coarse-ore stockpile serving the Ray Concentrator. • A nominal 27,200-tpd (30,000-stpd) concentrator, including semiautogenous grinding, flotation, copper concentrate filtration and associated plant ancillary facilities. • A tailings disposal system. Flotation tailings are pumped from the Ray Concentrator to a 122-m (400-ft) diam. thickener, located 4.8 km (3 miles) southeast of the Ray Concentrator site. The thickener overflow is pumped to two 76.2-m (250-ft.) diam. concrete process-water reservoirs. The thickener underflow, at 45% solids, is pumped to a new tailings disposal site located at Elder Gulch. • An HDPE-lined temporary-containment area to collect material from Ray Concentrator plant upsets and local storm-water run-off from a 100-year, 24-hour rain event. •A reclaim-water system from the Elder Gulch tailing pond area to the Ray Concentrator. • A 610-mm (24-in.) diam. x 31.9-km (19.2 mile) long fresh-water pipeline from the Hayden fresh-water-well field system to the Ray Concentrator. The overall process design criteria for the new Ray Concentrator is based on a nominal throughput of 27,200 tpd (30,000 stpd) of ore at 90% plant availability. However, based on the maximum performance capacity of the installed grinding equipment, it may be possible to achieve a sustained operating level in excess of 36,300 tpd (40,000 stpd) when processing soft ores. The balance of this paper will cover the major process systems including:

Jan 1, 1995

By R. R. Klimpel

The process of flotation is an extremely important solids separation technique employed in a wide variety of industrial process applications. Froth flotation is practiced in the coal industry to recover fines produced during the mining and cleaning of coal. A recent review article by Aplan (1) covers the processing variables encountered in the flotation of coal and the variety of chemicals and operating conditions which affect recovery. Numerous engineering and scientific studies have been performed with the goal of providing semifundamental laws of flotation behavior for improved screening of flotation chemicals, better equipment scale-up factors, etc. Often the results of such work are expressed in the form of mathematical models (e.g. 2, 3, 4, 5, 6) which are potentially useful for evaluating (simulating) on paper such alternatives as possibles process operating or configuration changes, the effects of ore and reagent changes, etc. It appears to be commonly accepted that a complete scientific/engineering characterization of flotation is immensely complicated and not sufficiently developed at the present to accurately predict (or understand) many important industrial facets of flotation. Thus, one is often reduced to detailed experimental characterization in both the laboratory and plant in order to fully evaluate flotation changes or alternatives. It is the purpose of this paper to describe a method of batch laboratory data characterization that is useful in evaluating flotation chemical reagents including froth flotation of coal. The approach consists of running a series of time-recovery curves in a batch float cell followed by the computer curve fitting of this data to a series of mathematical models based on semi-physical reasoning. The unknowns or parameters of these models are then optimally chosen so as to best fit the experimental data. It has been found in both coal and mineral systems that changes in reagent type, concentration, system pH, grind, etc. cause very consistent and logical changes to

Jan 1, 1979

By William F. White

It is a pleasure to have the opportunity of being here today to discuss the application of horizontal filters in the metallurgical industries. The use of horizontal type filters has been limited in metallurgical plants. However, in the recent past there have been new designs of this type equipment which greatly broaden their field of application. Through their use in many applications, important economies can be achieved over more conventional methods. The first of the modern continuous horizontal filters was initially developed by Oliver United Filters as their scroll type horizontal filter. This was an outgrowth of the old Oliver Sand Table that was limited to very coarse, free filtering pulps containing no appreciable amount of fine particles. The sand table was rather limited in application. The later continuous scroll type horizontal filter provided for a reverse air blow after discharge which reslurried the heel remaining and permitted the filtration of pulps containing finer particles. In the manufacture of phosphoric acid by the ?wet? process, the filtration of gypsum from the strong acid presented an extremely difficult filtration problem due to blinding of the filter media caused by crystallization of the soluble salts contained in the acid. A filter which allowed for continuous cloth washing was required, and this led to the development of the continuous pan type, and travelling belt type horizontal filters which provided for this need. Among the filters developed were the Prayon by Engineering and Industrial Corporation of Luxembomg for use in their phosphoric acid plants. They are one of the largest manufacturers of phosphoric acid in Europe. The Dorr-Oliver Traveling Pan Filter was also developed by Mario Giorgini, Manager of Dorr-Oliver?s Italian subsidiary, for use with the Dorr Company?s phosphoric acid process. Basically, there are four existing types of horizontal filters in commercial use at this time: The scroll discharge non-pan type, the continuous belt type (Lurgi), rotary pan type, and the traveling belt type. The construction and principle of operation of these various filters will be discussed.

Jan 1, 1958

By J. Guzman

Introduction The Carlin Trend is North America's premier gold producing district. It is located in northeastern Nevada's Elko and Eureka Counties along a northwest trending belt about 65 km (40 miles) long and 8 km (5 miles) wide (Thorstad, 1989; Jones, 1989). This trend is the worldwide reference site for epithermal, sedimentary rock-hosted microscopic gold deposits. At least 19 deposits have been discovered to date, varying in size from 933 kg to 1.08 kt (30,000 to 35 million contained oz) of gold (Fig. 1). Newmont Gold Co. and its parent, Newmont Mining Corp., jointly constitute the largest mineral right holders in the district. They own or control more than 1000 km' (386 sq miles) in and around the Carlin Trend and own all or part of I6out of the 19 mines and prospects identified to date. Since the initiation of Newmont's exploration activities in the Carlin Trend in 1961, 2.24 kt (72 million oz) of cumulative gold resources have been identified. Cumulative production from all mines since the start-up of Newmont's Carlin mine in 1965 to the end of 1989 was about 202 t (6.5 million oz) (Jones, 1989). The incentive of sustained high gold prices and innovation in processing technology resulted in a significant acceleration of gold output over the last few years. Newmont Gold alone produced more than 43.5 t (1.4 million oz) in 1989. That is equal to 22% of the cumulative 1965 to 1988 output, and an almost 200% increase over its 1986 output. The same incentives produced even more spectacular exploration results. In each of the last five years, net additions to reserves and resources outpaced current production by substantial margins. These facts demonstrate the spectacular past prospectiveness of the Carlin Trend and the success of focused, multi-disciplinary exploration methods that made it possible to more than offset the recent accelerated depletion of gold resources. However, is this situation sustainable? How long can the mining companies along the Carlin Trend keep on finding resources faster than they deplete them? These are some of the questions that motivated this study. The authors have not quantified the future potential for gold exploration in the Carlin Trend nor established a deposit discovery path. But strong indications were discovered that the [ ] Carlin Trend remains a relatively immature exploration district and that the potential for significant new discoveries is high. Methodology and data The approach chosen to address the above questions was simple. The authors compiled deposit size data, measured in contained ounces of gold resources, for all known deposits along the Carlin Trend (Table 1). The resource information was obtained by adding cumulative historical production (adjusted for mining losses and metallurgical recovery) to 1989 year-end published resource inventories. In a mature exploration area, where most deposits have been discovered, this distribution would be expected to approximate lognormality and would plot along a straight line on a lognormal probability scale. This result was found in previous work by Allais (1957) and recently confirmed by Cox and Singer (USGS, 1986) in regard to various types of mineral deposits in several regions of the world. It was also found to hold true for oil and gas pool size distributions (Arps and Roberts, 1958; Kaufman, 1962; McCrossan, 1969). [ ] The data used were compiled by Newmont Exploration geologists. The purpose of the study is to make inferences about the underlying geologic processes in the district and the maturity of the exploration effort. Therefore, deposits were not classified according to ownership but according to geologic occurrence as known from current information. Newmont's Post and Barrick's Goldstrike and Betze deposits, for example, are shown as a single occurrence to reflect the actual geologic setting. The cumulative frequency distribution of deposit sizes was plotted on lognormal probability paper (Fig. 2). The abscissa shows the cumulative fraction of deposits at or below a certain deposit size and the ordinate shows the deposit size in thousands of ounces of contained gold resources.

Jan 1, 1992

By R. H. Moore, B. D. Breitenstein

INTRODUCTION The United States Uranium Registry (USUR) tissue program was funded in 1978 by the United States Department of Energy (DOE) through its Human Health and Assessments Division, and registrant enrollment began in 1980. It is operated by Hanford Environmental Health Foundation (HERF), Richland, Washington, with support provided by Pacific Northwest Laboratory (PNL).** The USUR tissue program is the first systematic effort to contact and gain assistance of workers occupationally exposed to uranium and to seek and study uranium deposition in human tissue. This paper describes the program objectives, populations selected for study, procedures for enrolling workers in the program, types of tissue to be studied, and analytical procedures to be used. PROGRAM OBJECTIVES The objectives of the USUR tissue program are to: 1) Determine the distribution and concentration of uranium, if any, in the tissues of occupationally exposed workers. 2) Compare bioassay measurements of exposed individuals with the results of analyses of tissues obtained at autopsy. 3) Seek evidence of histopathologic changes related to any uranium deposition that may be present. 4) Conduct analyses of whole bodies, when available, to obtain more precise data on the uranium burdens, if any, in the body and organs, and especially the distribution in parts of the body, such as the skeleton, that are not usually accessible for sampling. 5) Develop data that will assist in evaluating a) the accuracy of current in-vivo measurement techniques, b) the propriety of existing regulations, and c) the adequacy of current protection programs. SELECTION OF POPULATIONS FOR STUDY Selection of the populations for the USUR tissue program was based on studies of the United States Uranium Registry described elsewhere (0c81). Potential populations for study were quite varied because of occupational exposure to different chemical forms of uranium, different levels and eras of exposure, varying ability to identify populations exposed in the past, and the general interest and cooperativeness of the populations. Nevertheless, certain identifiable populations emerged that were both willing to participate in the study and likely to provide useful information. Among the targeted populations are individuals who were exposed to uranium prior to the existence of modern exposure standards. These individuals are presently being enrolled by the USUR. The reliability of concentration and distribution data and the demonstration of effects are more likely in such individuals than in those who have received less exposure. However, the targeted groups also include individuals who Have been exposed to permissible levels of uranium, and reference employees in uranium plants who have not worked with uranium. The lesser exposures are of immediate interest because of the rarity of heavy exposures under current standards. The sampling of potentially exposed individuals with negative in-vivo measurement results may serve to check the adequacy of in-vivo measurements in the detection of deposition. [ENROLLMENT PROCEDURE] The enrollment of participants follows three patterns. 1) Presently employed workers are enrolled by the cooperative efforts of USUR staff with the medical, industrial relations, and/or health physics personnel of the uranium facility. Volunteers may be enrolled by medical personnel at the time of their physical examination or by health physics personnel at the time of a bioassay or lung counting procedure. Follow-up after initial contacts with currently employed uranium workers is carried out by on-site personnel, but subsequent follow-up is the responsibility of the Registry. 2) Retired workers are contacted by mail, with a covering letter from their former employer supporting the principles of the study but leaving participation in the program on an entirely voluntary basis. 3) An alternate method of enrollment is to obtain a USUR autopsy consent after death from the next of kin. As part of enrollment in the program, permission is requested for access to the individual's medical and exposure data, and a short occupational history is filled out. The autopsy permission agreement signed by the individual is for an initial period of 5 years; the USUR ordinarily seeks renewal of the agreement upon its expiration. While this agreement provides

Jan 1, 1981

By J. R. Knudson

A major contribution to the art of blasting was made at the Cleveland- Cliffs Iron Company?s Hawkins Mine in Cashwauk, Minnesota during April of 1956. It was here that the first experiments with fertilizer grade ammonium nitrate were conducted-experiments which led to the development of the ammonium nitrate and fuel oil method of blasting which has been eagerly adopted by open pit and quarry operators throughout the United States. While this new blasting agent was a more or less natural outgrowth of the Akremite Process devised by Maumee Colleries of Terre Haute, Indiana; no one, to our knowledge, had used this particular combination of ingredients prior to this time. Certainly this was a "break-through" as far as the Lake Superior District was concerned. Akremite consists of a mechanical mixture of grained ammonium nitrate and a solid carbonaceous material packed in a plastic bag. At the time of its introduction to the Mesaba Range, Akremite sold for 10.5 cents a pound as compared to the 18 cent powder previously used in both wet and dry large hole blasting. The discovery of this agent was indeed a remarkable achievement, one that afforded a substantial reduction in blasting costs. However, Akremite proved to be only an intermediate step in the evolution of our present low cost explosives. Cleveland-Cliffs utilized prilled ammonium nitrate and fuel oil and then eliminated the mixing and packaging plant entirely by combining the two raw materials in the field at the drill hole collar or in the hole itself. Thus we have approached the ultimate in simplicity, for the blaster and his helper now manufacture their own explosives not only as they are needed but where they are needed, and at a cost of under 4 cents a pound. This two-man crew may charge and explode as much as 8 tons of ammonium nitrate in an eight-hour shift and in so doing break some 65,000 tons of ore.

Jan 1, 1959

By Joseph F. Shirley

Introduction Inorganic depressants are chemicals added to the froth flotation process to maintain or produce hydrophylic surfaces on one or more minerals so they will remain in the pulp rather than attach to the air bubbles. Whether a depressant will be effective in depressing a given mineral depends on how it is used and the environment in which it is used. Some depressants must be added and conditioned into the pulp before the collector is added. Other depressants can be added in the presence of previously added collectors and effectively depress the desired minerals. Often the concentration of depressant relative to the collector concentration is critical to making an economic separation. It should be noted that some depressants will only work when specific collectors have been used. Some reagents such as sulfuric acid and hydrogen peroxide essentially act as depressants by altering the previously added collectors so that they are no longer effective. Some depressants such as sodium ferrocyanide are only effective in a very limited pH range and an essentially collector free environment. Major Depressants CaO Milk of Lime is by far the most used depressant both in tonnage and dollar value. Although it is most commonly listed as a pH modifier, it is also an important depressant for pyrite in copper and copper molybdenite flotation plants. Although a simple pH adjustment will often depress pyrite, there are times when grinding with fresh milk of lime is required to obtain optimum depression. Lime is also a molybdenite and gold depressant. NaSH Sodium hydrosulfide is by far the most commonly used reagent to depress copper and iron sulfide minerals in by-product molybdenite flotation plants. NaSH also depresses gold, silver sulfides and silver chloride. ZnSO4 Zinc sulfate is commonly used to depress sphalerite in lead-zinc and copper-lead- zinc flotation plants. It has also been used to effectively depress talc in by-product molybdenite circuits at a pH of 6.5.

Jan 1, 1986

By E. Turner

This is the 3rd Paper in a series by this author, the first two being published at the two previous International Conferences. Since the Aachen Conference, Rio Tinto has carried out an extensive benchmarking exercise to see how we are positioned with respect to other leading companies (in our sector and other sectors of major economic importance). We need to be sure that Rio Tinto is at the forefront of best practises in Sustainable Development (SD) and is using the most effective tools and methods. This paper will present key findings from this work. Rio Tinto Minerals, working as representatives of IMA-Europe was a leading contributor to the European Commission DG Enterprise Voluntary Reporting Scheme for SD Indicators in the Non-Energy Extractive Industry. In Rio Tinto Minerals we have been using these SDIs in the management of our business and the paper will report on how they contribute to the management of our business and the paper will report on how they contribute to business value in: deepening customer relationships, eco-efficiency of operations, land use planning and permitting for new and expanding facilities, community relations, policy engagement with government authorities and strengthening the bond between the company and employees. We continue to support the Voluntary SDI Reporting Scheme, considering it to be important in the expanding EU and as a model for other regions globally. For example we have ore suppliers in developing countries and we use these SDIs in assisting them to better their performance, for we have an obligation to use our influence for continuous improvement. The paper will describe this work. Over the last 12 months our company has created a new Industrial Minerals unit called Rio Tinto Minerals which brings together all the borates, talc and salt operations, R&D, marketing, sales and customer care worldwide. The paper will present also the new Sustainability Policy of Rio Tinto Minerals.

Jan 1, 2007

By N. E. Norman

A great deal of effort has been put forth in recent years to arrive at accurate projections of the demands for tunnels in this decade. In reviewing the statistics presented by various study groups, it appears that during the decade from 1960-69, there were some 1,335 miles of rock and soft ground construction tunnels excavated throughout the world. These statistics indicate 645 miles of rock tunnel and 689 miles of soft ground tunnel were excavated during the last decade. This is expected to increase to 3,000 miles in the 1970's according to projections made by various authorities in the field of construction tunneling. I point out the above statistics to emphasize two main points: (1) The demands for tunneling in this decade alone are staggering. (2) There is a fairly even distribution in the amount of rock tunneling and soft ground tunneling being excavated. Unfortunately, available statistics do not answer many important questions about tunneling which are of great importance to the contractor and to boring machine designers. For example, how many of the projects completed in the past decade involved both soft ground and rock tunneling? How many projects involved tunneling in conditions where both rock and soft ground were contacted at the same face. While the answers to these questions remain unanswered, I am sure most of you can think of numerous examples of projects where mixed face conditions are prevalent. Many of you are probably familiar with the Austin Crosstown Interceptor which was bid last month in Austin, Texas. Here is a project involving 57,000 feet of tunnel where limestones and clay shales are expected to be traversed. Another project, the Tonner Tunnels No. 1 and No. 2, near Los Angeles, involve some 22,000 feet of tunnel where mixed soil and rock conditions are expected. A large majority of the projected tunnels for this decade are to

Jan 1, 1997