Search Documents

By David A. Summers, Clark R. Barker

INTRODUCTION The use of high pressure water as a means of excavating valuable mineral from the earth dates back many hundreds of years, but is most familiar through its use in sluicing the gold bearing deposits of California and Alaska. Interestingly, that practice, which dates back from at least 1852, is now nearly defunct with only one known surviving hydraulicking operation.(l) In that particular development water under a relatively low, natural pressure head is carried to a nozzle and from the nozzle it is thrown a distance of perhaps 20 ft to wash the gold bearing material down into a channel from whence it's carried over some mineral collector, and the water is then recirculated. Development of this practice in coal mining began in Russia in 1915, and Dr. Muchnik established the criteria for hydraulic mining during the 1930's. The first water jet mine was established underground in 1939 and has been followed by several larger mines to the present day where there are at least 11 large mines producing about 10 million tons of coal per year in the Soviet Union.(2) Water jet mining has expanded from Russia through Japan, Germany, Poland, Czekoslovakia, and mainland China. The nearest location to the United States is currently at the Kaiser Mine in Sparwood, British Columbia, where a three-man crew has mined up to 3,400 tons of coal in a 6-hr shift. There are many advantages to this particular operation. It is one of the safest mining operations for coal in Canada and has won safety awards because of this. The process is relatively cheap since the cost of the equipment is much lower than that which would be required conventionally using either longwall or shortwall mining, and transportation is achieved by fluming the coal to a central station using a gravity feed and then pumping to the surface, (3) For this

Jan 1, 1976

By Jack E. Thompson

I have spent my entire life in the mining industry pursuing what I believed was an honorable profession that provided products that were critical for our social and economic well being. Now I am told that all of my efforts been for nothing and that I have been doing something morally wrong - mining. This view of the future is not one that the mining industry has to allow to unfold. A determining factor in how things will turn out is continued improvement of the industry's environmental performance. To some extent, the current state of affairs in the United States is a result of the common perception that greedy corporations (usually foreign) are somehow ripping off US citizens of their native birthright or natural treasures in the name of corporate profits. Implicit in this view is the belief that corporations will take shortcuts or violate the environment in the name of profits. I have 26 years of experience in working in the copper, uranium and gold industries. Profits during those years were meager and difficult to find (Fig. 1). In fact, when I began working fresh out of college, I chose copper, which was then selling at around $1/lb. By the time I left copper mining, it was selling for 45 cents/lb. I then moved to uranium, which was selling for $52/lb. By the time I left it was $16/lb. I finally picked gold, which was then at ($650/oz). There is a whole generation of engineers, geologists and professionals who have spent two decades downsizing, closing mines, improving costs and getting smarter about how the mining industry does what it does. The environment, health and safety are areas where there have been great improvement. There are five characteristics of corporate governance that are critical for a company to develop and an industry to embrace if environmental, health and safety excellence is to reach new heights in the labor pool.

Jan 1, 1997

By William J. Maloney

OVERVIEW Blind drilled shafts are becoming increasingly popular, particularly in the Appalachian coalfields, as a secondary and sometimes primary means of ventilation. The reasons for the rebirth of the blind shaft are mainly due to it's economics, timeliness, safety characteristics and inherent independence from underground operations. Historically blind drilling has been used to a limited degree in hard rock and tunneling ventilation. With the recent advances in cutters, bit design, equipment and lining systems, particularly in the Appalachian coalfields, blind drilled shafts are once again the shaft construction technique of choice to the educated ventilation specialist. [ ] HISTORY OF BLIND DRILLING Blind drilling has it's roots in numerous places, including the Nevada Test site, the coalfields of Appalachia and Germany along with the uranium mines of Arizona. Early technology was developed using a variety of equipment mainly of oilfield origin with oilfield drillers entering the industry on a project basis only to "pull in their horns" and return to the oil patch. Shafts completed by oilfield equipment range from the shallow 5' and 6' lined shafts on the Nevada test site to two (2) 10' lined, 730' deep shafts in Alberta for heavy oil development. Several of these shafts were completed to extraordinary depths with the record being a 90" diameter, 6,150' deep shaft being completed in the Aleutian Islands of Alaska in 1969. EQUIPMENT Oilfield equipment is still being used on the Nevada test site but elsewhere specialized blind hole equipment has been developed to enhance the efficiency of particular applications. Where steel liners are required the A-leg derrick with a simple hoist and rotary system is used. The largest user of this type equipment in the world is the former USSR where blind drilling for mine ventilation is the norm. On applications where trip time and cutter changeout are a priority, top drive hydraulic rigs have been developed which are highly automated, efficient and mobile. These rigs are particularly well suited for tunneling applications where shafts are shallow and sites are usually tight.

Jan 1, 1993

By Donald A. Dahlstrom, Wai-Ping Kam

The mineral industry and individual processing plants are large consumers of energy. While energy conservation has received some attention in the present Federal Administration National Energy Strategy proposal it is obvious that the mineral industry should also continue to emphasize energy consumption reduction for important economic savings alone. As indicated by other studies, comminution is the largest single consumer of energy in the mineral processing plant (1.3% of total electrical energy consumption in the U.S.A.).1 Fine grinding is the largest portion of this amazing statistic. While substantial energy savings have been demonstrated by new machine developments and improved control methods, undoubtedly there are additional areas in comminution where substantial progress can be made. Some time ago, the U.S. Department of Energy published a report on "Comminution and Energy Consumption" by a committee composed of experts in the field of comminution from industry and academia. They identified the following potential for energy savings by specific areas? Classification device design 9-13% Comminution device design 3-16% Control 9% Grinding additive 3-6% Materials 3% It is apparent that the classification device had the first or second highest savings potential. Obviously, serious research consideration must be given to this technology area. A series of three papers have previously been written on the subject of two stage classification research work for ball mill operation by the authors. Accordingly, a brief review will be made. Previous Research Results on Two Stage Classification The hydrocyclone was selected as the type of classification equipment for this study as it represents by far the majority of the devices used in ball milling. While four different hydrocyclone circuits have been proposed by others,3 only two were considered in this work as illustrated in Figure 1. Flowsheet A is truly counter-current in nature in that the product from the ball milling circuit is taken from the first stage overflow

Jan 1, 1992

By T. K. Bundtzen, C. B. Green

Exploration expenditures in Alaska last year amounted to $8.9 million. This was comparable to 1985's $9.1 million. Development expenditures dropped 29%, $24.3 million in 1986 vs. $34.1 million in 1985. The exploration industry is restructuring and stabilizing after the loss of major mineral firms during the last few years. These included Anaconda Minerals, Asarco, Hecla Mining, Enserch Exploration, Phillips Minerals Division, Exxon Minerals, Noranda Inc., General Crude, Mohawk Oil & Gas, Inspiration Development, Teton Exploration, and St. Joe Minerals Division. Some of these companies were mineral subsidiaries of oil companies and were either dissolved or redirected to programs outside of Alaska. However, recent entry exploration firms include Echo Bay Mines Ltd., Long Lac Minerals, and Exvenco. They are busy evaluating prospects and mineral developments in the southeastern panhandle. In the 1970s, about $254 million was spent on Alaska mineral exploration. Of this, about 5% ($12 million) was for nonmetallics and coal, about 26% was directed at precious metals ($66 million) mainly gold, and 69% ($175.3 million) for the base metals zinc, copper, molybdenum, tin, tungsten, and nickel. Since the early 1980s, trends have reversed. Of the nearly $196.3 million spent from 1981-1986, 48% has been for precious metals ($94.3 million) and 40% on nonmetallics and coal. In the last two years, nearly 70% of the Alaskan exploration dollar has been spent in search of precious metals. Three gold skarns were explored during the year - the Nixon Fork project in western Alaska (Battle Mountain Mining Co.), the Nebesna and Rambler lodes of the northern Wrangell Mountains (Nebesna Mining Partners), and the Zackley project near Paxson in southcentral Alaska (Nerco Minerals). Nearly 7.6 km (25,000 ft) of diamond and rotary drilling were conducted on these three properties. Aspen Exploration announced that significant gold mineralization was found under the Nome coastal plain in western Alaska. Meridian Minerals joint ventured with Resource Associates of Alaska, exploring precious metal

Jan 5, 1987

By G. L. Bloomsburg, E. G. Zahl

INTRODUCTION During the past decade, disposal of mine and mill waste material has become an increasingly important issue. Problems of structural stability and seepage effects on stability have been well addressed, and significant technological advances have been achieved [(1-4)]. The primary problem currently facing industry in the waste disposal area is environmental protection. The greatest environmental concern is over the amount of seepage or leachate entering the ground or surface water systems. Methods to determine the quantity of water seeping from a tailings pond have also been covered in the literature [(5-23)]. However, much further work is necessary to fully implement these techniques to evaluate tailings pond performance and accurately predict the various influences of disposal management on seepage from mill tailings. This study is an effort to develop those necessary techniques. The partially saturated method of analysis which is discussed here is applicable to most situations involving seepage from waste piles. In a conventional type of tailings pond, a slime layer is ordinarily built up under the ponded area. This material will consolidate slowly from capillary pressures and the weight of material deposited above it. In situations where this consolidation results in a slime layer of lower permeability than the native foundation soil, a partially saturated flow condition will usually exist in the native soil. This will result in a smaller quantity of water entering the ground-water system than would be predicted by saturated flow analysis. The finite-element program used in this study was originally developed by Neuman [(17)] and is called UNSAT2. The program will analyze problems of saturated or unsaturated, steady or nonsteady flow and can be used with a variety of boundary conditions such as constant flux, constant pressure, maximum flux, minimum pressure, and with infiltration, evaporation, and seepage surfaces. The maximum conditions are controlled by exterior factors such as atmospheric conditions; but the actual flow in the porous media is determined by properties of the porous media. In this test, the computer code was used

Jan 1, 1980

By Kenneth F. Wyman

The following report details the successful construction of Contract 2A of the Three Rivers Water Quality Management Program, Intrenchment Creek Combined Sewer Overflow Conveyance System, in DeKalb County for the City of Atlanta, Georgia. The contract required construction of approximately 2878 m (9443 ft) of tunnel bored to an initial diameter of 7.95 m (26 ft 1 in), with provisions to concrete line those portions designated by the engineer to a finished internal diameter of 6.91 m (22 ft 8 in). Flanking the tunnel are two shafts. The upstream shaft was excavated to a nominal diameter of 4.87 m (16 ft) to accommodate a finished internal diameter of 3.66 m (12 ft). This shaft required a transition boot fully concrete lined to final dimensions of 6.91 m (22 ft 8 in) wide, 13.72 m (45 ft) long, and varying in height from 6.91 m (22 ft 8 in) to 12.80 m (42 ft). Associated work necessary to complete the contractual obligations included installation of 22.86 m (75 ft) of cut-and-cover box culvert, 484 m (1589 ft) of open-cut sewer installation in sizes ranging from 0.30 m (12 in) to 1.68 m (5 ft 6 in), one river crossing, 137.46 m (451 ft) of monolithic concrete trapezoidal channel, and installation of 19125 cu m (25000 cu yd) of select fill material compacted and graded to finished contours. The downstream shaft was excavated to a minimum diameter of 12.04 m (39 ft 6 in) and concrete lined to a finished internal diameter of 10.67 m (35 ft). Requirements here included installation of a complete pumping station with all mechanical, electrical, and structural elements necessary for dewatering the tunnel through the controlled use of four 250 hp submersible pumps discharging into the facilities of the Intrenchment Creek Water Pollution Plant. The objective of this project was to collect combined storm runoff and sanitary flows currently coursing through Intrenchment Creek

Jan 1, 1985

By Wolfgang Pietsch

Roller presses were first invented in the middle of the 19th century, for the economical size enlargement of coal fines as fuels. Coal briquettes became quickly accepted for industrial and domestic use giving rise to a large and sucessful industry, particularly in Europe, Japan, and North America. When, towards the middle of the 20th century, coal was more and more replaced by other energy sources, such as electricity, gas, and oil, roller press manufacturers searched for alternate applications of this equipment. In addition to contemporary coal briquetting, in fields such as smokeless fuel and form-coke, it was found that redesigned and modernized roller presses, which are now capable of exerting high forces, are versatile machines for many tasks in mineral processing. Today they are used for: - the "classic" pressure agglomeration and - the "new" high pressure comminution. In pressure agglomeration, the characteristics of fine minerals are improved by forming briquettes or granulated products from compacts. During size enlargement with roller presses briquettes are directly obtained while granular materials are produced by crushing and sizing of compacted sheets. The processes are carried-out essentially dry and often do not require binders other than those inherently contained in the feed and "activated" by the high forces and/or elevated feed temperatures (e.g. hot briquetting). Therefore, no foreign materials (impurities) are added. Another advantage of the technology is, that wide particle size distributions are acceptable or desirable as feed materials, including millimeter or even centimeter sized particles. Plastic particles deform and brittle materials are crushed during pressure agglomeration. A relatively new application of roller presses in mineral processing is the utilization of the crushing effect when brittle materials pass the nip area between the rollers. It was found that this crushing mechanism is very efficient thus saving energy, particularly in grinding circuits handling large capacities. The paper introduces the fundamentals of the process and describes the design as well as applications of modern roller presses in mineral processing.

Jan 1, 1995

By Andrew Burton, Damian Schofield, Jeremy Noond

This paper will introduce and discuss a range of techniques that utilise new developments in Computer Graphics (CG) and Virtual Reality (VR) for the investigation of incidents and accidents in mining environments. The future of mining safety may not be totally led by the demands of the mine operators, but sometimes by the academics, commercial software developers and legal pioneers who generate new ideas and products and set admissibility precedents which may change the way certain traditional investigative operations are performed. In any accident investigation the outcome from the investigating team is often a complex affair and the results of the investigation are often reported in large, convoluted documents. Computer-generated forensic reconstructions allow investigators to present accident scenarios in an accessible and easily understood, visual manner. Surveys in the US have also shown that people have increased recall of computer-generated images over many other forms of evidence. The AIMS Research Unit in the UK have been pioneering the use of Computer Graphics (CG) and Virtual Reality (VR) technology for both industrial and road traffic accident reconstruction. This paper and accompanying presentation will contain examples of forensic reconstructions developed by the authors that explain some of the methodologies used to ensure admissibility of this type of digital evidence. The paper will contain a number of case studies based on UK and International industrial accidents. The paper will focus on how AIMS Research is extending the capabilities of the accident reconstructions created to take advantage of the latest developments in VR technology. As digital technology makes its impact within professional and commercial fields, computer generated forensic reconstructions will form important admissible evidence in the courtrooms of the future. The technology will also make a great impact in the way we train our workforces, with highly visual three-dimensional (3D) interactive training tools becoming the norm. Acceptance by the public, courts and workforce is an important issue, and implementation strategies must be considered carefully.

Jan 1, 2002

By S. Henley

There is much in common between the requirements of open-pit mining and quarrying operations. Both involve the extraction of large volumes of material from surface excavations. The principal differences are of degree: open-pit mining of materials such as coal or gold generally involves the extraction of only small volumes of 'mineral' and large volumes of waste-they are operations with very high stripping ratios, and are made viable only because of the high unit value of the extracted mineral. In quarrying operations, the unit value of the mineral - sand, aggregate, limestone, or clay - is much lower, but stripping ration Are also lower. Thus the same techniques of geological modelling, reserve estimation, and pit planning are applicable, as is shown in two examples from the British quarrying industry. In each case, a primary requirement is the definition of production volume or tonnage. Sometimes, this need may be addressed simply by the use of a survey data processing package. However, in other cases, such as the two examples addressed in this paper, of sand and clay quarries, detailed assessment of the variation of mineral grades is a vital part of the exercise, and simple volumetric modelling cannot in itself be sufficient. In these cases, a block model approach using simple logical and numerical post-processing is also required to obtain required parameters for commercial classification of the products to be extracted. Pit designs themselves may be optimised by use of algorithms such as Lerchs-Grossmann, but the value of mineral produced can be dependent on factors other than its grade in any one part of a single pit, and the 'optimised' pit itself must be considered only a good sub-optimal. Given the right degree of healthy skepticism, and a software package with sufficient flexibility to be adapted readily to the rather different requirements of the quarrying industry, there is no reason why the quarrying industry should not benefit from the many years of investment in mining software technology.

Jan 1, 1989

By Nikhil C. Trivedi, Robert W. Hagemeyer

Despite the apparently unflattering term filler, this group of industrial materials has become an essential component of many industrial products with varying degrees of sophistication. Mineral fillers are, by definition, inert materials included in a composition for some useful purpose. Included in this broad category are asbestos, barite, bentonite, natural calcium carbonates (limestone), clays, diatomite, feldspar, micas, silica, talc, and other industrial minerals. Also included in this category are synthetic mineral- derived materials such as aluminum hydrate, precipitated calcium carbonate, and pyrogenic and precipitated silicas and silicates. Mineral fillers are included in compounds to accomplish a variety of final results. Inclusion of fillers modifies physical characteristics such as hardness, brittleness, impact strength, compressive strength, surface texture, fire resistance, softening point, and electrical conductivity. Depending upon the performance characteristics of the particular filler used and the quantity of the usage (i.e., percentage added), these materials can enhance the physical and optical properties, price-performance, and appearance of the finished products. These enhancements in properties of the finished compounds are the result of properties of the fillers including chemical activity, purity, hardness, particle size, particle shape, particle size distribution, surface structure, color, density, and refractive index. This chapter will review the general usage of fillers, the rationale for their use, trends, and economic factors influencing those trends. Major using industries will be examined in detail with extensive discussion of major fillers used in those industries. The reader is referred to the appropriate commodity chapter for specific information on deposits and processing for industrial minerals. All of these same filler materials have additional significant uses based on their chemical composition or other characteristics. Cross-references for these will be found in other use chapters and summarized in commodity chapters. The chart in Table 1, updated from the 5th edition of Industrial Minerals and Rocks, illustrates the major mineral fillers (both natural and synthetic) and their more important end uses.

Jan 1, 1994

By Bart Bartholomew, Randall J. Essex

INTRODUCTION In June of 2004, at the North American Tunneling Conference in Atlanta, an all-day workshop was conducted to review the application of Geotechnical Baseline Reports (GBRs) for underground construction. The moderator for the program was Bart Bartholomew, former President of Fruin Colnon Construction Company. The program involved commentary by a panel of engineers, owners, contractors, and legal representatives within the North American tunneling industry, as well as an extended audience discussion. The panelists were: Peter Douglass, President, Peter Douglass, Inc. Randall Essex, Executive Vice President, Hatch Mott MacDonald Joseph Gildner, Deputy Director for Technical Services, Sound Transit Randall Hafer, Esq., Kilpatrick Stockton Robert Fitzgerald Esq., Watt, Tieder, Hoffer, & Fitzgerald Kirk Samuelson, Senior Vice President, Kiewit Construction Group DEVELOPMENT OF PROGRAM FORMAT The focus of the program was to assess the state of the practice in the preparation of GBRs, and to discuss improvements that could and should be made with regard to their preparation, interpretation, and application. The approach used to achieve this focus in the broadest possible way was unique, in that it involved the panelists’ preparation of the workshop format and materials months before the presentation of the workshop. First, each of the six panelists was selected by the moderator based on their reputation and involvement in their respective fields of expertise, taking care to maintain balance and contrast within the collective pool of talent assembled. Following selection and agreement to serve on the panel, each panelist was asked to independently submit to the moderator a list of the six most pressing issues involving GBRs that they each frequently encountered in their individual professional experience. Each was asked to rank their issues in descending order of perceived importance. This process resulting in a pool of thirty-six potential or “candidate” issues for use in the workshop program. Contrary to the moderator’s expectations, there was surprisingly little duplication among the thirty-six issues submitted.

Jan 1, 2005

By W. M. Ma, Daniel W. H. Su, K. Centofanti, Yi Luo, W. L. Zhong, Syd S. Peng

10.1 I~RODUC1'ION In order to understand the effects of surface subsidence due to underground mining on the ground water hydrology, a brief introduction to the rate, direction, and general pattern of ground water movement in aquifers is necessary. Ground water movement in an aquifer is controlled by aquifer lithology, structure, permeability, water levels, topographic set¬ting, and pumping patterns (Sgambat et al., 1980). Fig. 10.1 shows an idealized flow pattern of ground water in a hilly terrain (Coe and Stowe, 1984). The hill is made up of a series of interbedded permeable aquifers (mostly sandstone) and confining units (mostly shale). Since sandstone is porous and permeable, ground water moves through it downward and laterally until it reaches the interbeddings of the confining unit immediately below. The ground water then moves laterally along the interbeddings, be¬cause the confining unit is less permeable, and comes out as springs on the surface at the intersection of the aquifer and the confining unit. If there is a ground water table in each aquifer, it is a perched water table (e.g., right side of Fig 10.1). On the other hand, if the ground water recharge is larger than can be drained out, the interbedded permeable aquifers and confining units will be filled with water and a ground water table will exist only at the uppermost permeable aquifer. This is the semi-perched water table (e.g., left side of Fig. 10.1). There are three ground water flow systems: shallow, interme¬diate, and deep. Shallow flow systems occur near the land surface and the surface drainage system. The flow depth ranges from a few to several hundreds of feet with a resident time of a few weeks to a few years after entry, depending on the permeability of the rock strata. In a shallow flow system, the drainage coincides with sur¬face run-off water divides. Intermediate flow systems occur in minor hills some distance away from surface drainage. The travel distance ranges from several hundreds to several thousands of feet, the travel time from several months to tens of years. These systems are less dependent on seasonal recharge or discharge. In deep flow systems, the ground water travels from thousands of feet to miles, and transfers between surface basins. The travel time ranges from several tens to several hundreds of years. The systems generally receive recharge over a large area on major mountains and dis¬charge into major stream systems. 10.2 CASE STUDIES There are two ways of monitoring water wells for studying the effects of dewatering due to underground mining, i.e., water level and piezometric level. The water level is the water elevation in a water well that has penetrated two or more aquifers. Thus it indi¬cates the combined flow of all the aquifers that the water well intersects during the time of measurement. The piezometric level is the level to which water rises in a piezometer cased to a specific aquifer, and coincides with the pressure level of water in that aquifer. Therefore piezometric level reflects the water condition in that particular aquifer to which it is confined, while the water level represents the total yield of a water well without regard to the source of water. For instance, if a water well intersects two aqui¬fers, and if the lower aquifer is affected by undermining and goes dry while the upper aquifer does not, the water level in the well will drop, but may never go dry. Under this condition, the data obtained by monitoring the water level do not indicate the true behavior of the individual aquifers, especially if they are located at widely separated heights. 10.2.1 WATER LEVEL EFFECTS The effects of underground mining on ground water flow have been the subject of many investigations (Booth, 1984; Coe and Stowe, 1984; Owili-Eger, 1983; Rauch et al., 1984). However, the problems are very complicated, as have been exemplified by the conflicting conclusions reached by various investigators in var¬ious case studies. The most dramatic examples were described by Coe and Stowe (1984). In the first case (Fig. 10.2), the coal seam was 5 ft thick with cover from 400 to 800 ft deep. The majority of water supplies came from a sandstone aquifer in most ridge tops. When the face of the Panel No. 3 passed under it, dug well WW-1, which was approximately 670 ft above the coal, went dry, while the water level in Borehole B- 1, which was located at the center of Panel No. 4 with the bottom reaching the coal seam, also dropped about 160 ft. In Panel No. 5, the developed spring DS-2, which originated from the surface of the sandstone/shale contact and was approximately 750 ft above the coal seam, stopped when the face passed under it. The water level in the dug well W-2, which was dug into the shale about 700 ft above the coal seam dropped about 22 ft, but the well did not go dry. Therefore, nearly every spring or well located above or near the active panels was affected by longwall mining. In the second mine (Fig. 10.3), the seam was 5 ft thick with cover from 200 to 400 ft thick. Dug well DW-2, the bottom of which was 35 ft deep and approximately 330 ft above the coal seam in a perched sandstone aquifer, went dry right after the longwall passed under it. Drilled well W-3, in the sandstone aquifer, about 220 ft above the coal seam, experienced a 75-ft drop in water level when the face was under it, but showed some re¬covery after the face had passed under it. Ponds P- I and P-2 were developed in shale bedrock and were spring fed. They were not affected by longwall mining. Pond P-3 was developed in the sand¬stone aquifer, and its water table showed some decline when the face passed under it. Spring ST-1, which originated from Pond P-1 and was fed from several tributary valleys, was affected by longwall mining, probably because it passed across the panel edges where tension cracks drained off the water. Although the overbur¬den in case 2 was about half of that in case 1, the majority of water resources were not affected by longwall mining. Coe and Stowe (1984) attributed this discrepancy to: (1) a higher percentage of clays, shales, and claystones, resulting in a lesser degree of inter¬connected fracturing, and (2) a less rugged topography resulting in a less localized ground water flow system. Therefore, in order to assess the effects of underground mining, the premining ground water flow patterns, topographical, lithological, and meterological conditions must be known. Booth (1984) also monitored the ground water effects of a longwall mine (Fig. 10.4) in a seam 5 ft thick and 300 to 800 ft deep. There were three major aquifers: Morgantown sandstone approximately 30 ft thick and 630 ft above the coal; Saltsburg sandstone of up to 50 ft in thickness and 520 ft above the coal; and

Jan 1, 1992

By T. Klemetti, W. H. Su, M. A. Van Dyke

Entry stability in coal mines is dependent on geologic conditions and engineering controls. Most engineering controls in ground control are predictable and standardized for typical geologic conditions. However, geologic anomalies may exist that are difficult to detect with traditional core hole drilling. Borescopes offer a cost-efficient way to gather more geologic data between core holes. Additional data obtained from borescope results provide a clearer picture to enhance detection of hazardous conditions due to geologic anomalies. The equipment, methods, and analysis of borescope results provide geomechanical engineers with a clear understanding of strata behavior and the best information to implement roof control plans and supplemental support to enhance miner safety and health. INTRODUCTION Borescope technology has changed very little since its inception. However, the idea to use borescopes to examine roof strata started with the U.S. Bureau of Mines in 1979 with the production of a fiber-optic borescope (FitzSimmons, et al., 1979). The first documented use of a borescope in the coal mining industry began during the 1980s in Australia by researcher John Shepherd. Shepherd’s idea was to use a borescope to collect a series of data points from the roof lithology and compose a geologic cross section. The cross section was then used to identify key features that suggested the beginnings of roof failure. The features Shepherd identified were bedding plane separations in the roof and low angle, extension, and tensile failures. Shepherd also suggested that the borescope findings could be used for geologic mapping for lithological variation, fracture distribution, and determining if supplemental roof support was needed (Shepherd, et al., 1986). In the United States the first publication about borescope usage for coal mine stability assessment was by Su and associates in 1999, who specifically related the combination of using borescope, geophysical, and corehole data to produce geologic hazard maps (Su et al., 1999). This work directly linked the usage of a borescope with the design of supplemental roof support. The use of borescopes in mining was adopted industry wide by the 2000s. Operator case studies were being published using borescopes to aid in supplemental support recommendations and hazard mapping. An Australian study published in 2007 based the optimization of secondary support after each longwall pass on the results of borescope data. The study stated that the borescope was an invaluable tool for understanding roof behavior (Black, et al., 2007). In 2009, a publication by the National Institute for Occupational Safety and Health (NIOSH) took the concept of borescoping one step further. The work centered around creating a roof quality index (RQI) for limestone mines based on borescope data. The RQI attempted to assign a ranking to establish the nature of the roof and its stability (Ellenberger 2009). In theory, this would have been a very useful tool, but the RQI system has not been widely adopted in the industry.

Jan 1, 2019

By Yuexin Han, Mu. Yufan, Yanjun Li, Peng Gao, Yongsheng Sun

"The objective of this study was to evaluate the effect of reduction temperature, reduction time and binary basicity on the size of metallic iron particles in coal-based reduction products of an oolitic iron ore. The particle size distribution behavior (i.e., cumulative passing percentage and mean size of metallic iron particles) during reduction was investigated in detail. Results showed that the particle size distribution of metallic iron particles was strongly influenced by reduction temperature, reduction time and binary basicity. The cumulative passing percentage and mean size significantly increased with reduction temperature and time in the entire range of the experiments. All curves of cumulative passing percentage versus particle size under different conditions demonstrated a similar trend (continuous increase). The size distribution parameters and mean size slightly increased with increasing binary basicity and significantly decreased when the binary basicity exceeded 1.0. The size of metallic iron particles could be controlled by adjusting the reduction conditions during coal-based reduction.IntroductionThe increasing demand for iron ore coupled with diminishing high-grade iron ore reserves has resulted in the urgent need for innovative technologies in order to use refractory iron ores. Oolitic iron ore is a typical refractory iron ore with tremendous abundance globally. Based on published literature, oolitic iron ore reserves are approximately 140 million tons in Europe, 10 billion tons in China and 66 million tons in Pakistan (Kazmi and Abbas, 2001; Wu et al., 2011; Yu and Qi, 2011; Sun et al., 2013a). Therefore, the efficient exploration and use of oolitic iron ore resources can play a significant role in easing the mineral resource crisis in the iron and steel industry. However, oolitic iron ore cannot be effectively upgraded by traditional beneficiation methods due to its mineralogical characteristics (e.g., low grade of iron, poor liberation of iron minerals and high phosphorus content) (Li et al., 2011b; Sun et al., 2013b).Researchers recently proposed coal-based reduction followed by magnetic separation to recover iron from refractory iron ores (especially oolitic iron ore) and a certain degree of breakthrough was achieved in both theory and practice. In this technology, iron minerals in the ore are directly reduced by coal to metallic iron, which grows into particles of different sizes. After comminution and liberation, metallic iron is concentrated by magnetic separation (Srivastava and Kawatra, 2009; Sun et al., 2013a; Li et al., 2011b; Sun et al., 2013b; Li et al., 2011c; Gao et al., 2013). Sun et al. and Gao et al. used this technology to examine the recovery of iron from oolitic and Bayan Obo iron ores, respectively (Sun et al., 2013a; Li et al., 2011b; Li et al., 2011c). Metallic iron powder with more than 90% iron content was obtained as the final product, which could be used directly in steel production."

Jan 1, 2015

By Carrie Smith

The Society for Mining, Metallurgy & Exploration’s annual conference and expo, MINEXCHANGE 2026, will take place Feb. 22–25, 2026, at the Salt Palace Convention Center in Salt Lake City, UT. The event will foster a hub for innovation, technical exchange and policy discussion for the global mining industry. Over four days, attendees will take part in short courses, technical sessions, field trips and networking events that highlight the advancement of the mining industry. The conference’s keynote session, titled “Regaining America’s Mineral Dominance,” will start at 8:30 a.m. on Feb. 23 in the Grand Ballroom E–J. The speaker will address the sweeping policy actions now shaping the nation’s mineral future, following a series of executive orders issued by the Trump administration designed to bolster domestic mineral production and energy security. These directives, including Immediate Measures to Increase Domestic Mineral Production (EO 14241) and Establishing the National Energy Dominance Council (EO 14213), have set in motion a coordinated effort across the Departments of Interior, Energy, Defense and Commerce to enhance the United States’ position as a global leader in critical minerals. The invited speakers include Utah Governor Spencer J. Cox and Nate Foster, managing director of Rio Tinto Kennecott, who will examine how policy and industry are converging to meet surging demand for minerals essential to modern technology. Governor Cox is expected to highlight Utah’s long-standing role in American mining, from the early development of Kennecott Copper to its current position as a producer of 40 of the nation’s 50 identified critical minerals. Foster, meanwhile, will offer insights into Rio Tinto’s extensive operations in Utah, including the Kennecott Copper Mine — one of only two operating copper smelters in the United States — and the company’s ongoing efforts to build more resilient, sustainable supply chains. Rio Tinto’s work in critical mineral production, from copper and tellurium in Utah to new operations in Arizona, has made it a fundamental figure in the U.S. mineral economy. Projects such as the Resolution Copper development and the revival of Gunnison Copper using Rio Tinto’s innovative Nuton technology illustrate how private-sector leadership is driving sustainability in domestic mining. These advancements come at a critical moment for the industry, as copper prices remain near historic highs. The keynote session will emphasize that meeting future mineral demand will require a concerted effort between government, industry and technology partners to secure responsible, domestic production. Immediately following the keynote, the Robert E. Murray Innovation Award Lecture will start at 10 a.m. as part of the same session. Lucy England, managing director at FLSmidth, will present on “Sustainable Copper Mining Flowsheets and the MissionZero Mine.” England, who has spent more than 25 years in mineral processing and innovation, will discuss how FLSmidth’s MissionZero initiative aims to develop the world’s most efficient

Feb 1, 2026

By Peter J. Szabo

Many mining engineers tend to think of the economic analysis of mining ventures and projects on an f.o.b. mine basis. This is especially true of mines that are operated in an established domestic mining district. Here, transportation costs are many times smaller in comparison to overall delivered prices. One has only to consider the development economics of taconite mines in Minnesota with production destined for lower lake ports to see the truism of this statement. In the international arena, however, with consumers such as Japan and Europe located thousands of miles from source countries such as Brazil and Australia, the situation is different because mineral transportation is often a critical factor in determining project viability. This article is being presented to provide a basic understanding of the factors that govern ocean transportation of the three largest bulk mineral commodities shipped around the world: iron ore, coal, and phosphate. The major dry bulk commodity trades as a percentage of volume shipped are iron ore, 45%; grain, 25%; coal, 20%; phosphate rock, 5%; and bauxite and aluminum, 5%. Most of these commodities are carried by bulk carriers rather than tankers. These are vessels that have cargo, usually in solid form, loaded directly into the hold of a vessel by shore-side materials handling facilities or, in the case of a geared bulk carrier by the vessel's cranes and derricks. Gearless bulk carriers are used in most cases for iron ore and coal. Geared bulk vessels are mainly used for minor dry bulk trades such as ore concentrates (copper, lead, zinc, etc.), fertilizers (phosphate, potash, etc.), cement, petroleum, and coke. There has been, however, a trend toward using more self-unloading ships in both iron ore and coal ocean transport. And large vessels, such as the Universe Kure of Japan, have been designed with a cargo capability of 157 kt (155,000 dwt (deadweight tons)). Trade patterns of major bulk commodities are influenced by the Panama and Suez canals. Both of these canals have draft limitations that prohibit large, deep-draft, ocean-going vessels from using them for shorter trade routes used by Panamax and Suex vessels. The shipping industry has developed two widely used vessel classes; the Panamax and Suex vessels. The former is the maximum size vessel that can pass through the Panama Canal, usually 51-61 kt (50,000 - 60,000 dwt), depending on the season and draft of the vessel. The Panama Canal is usually 0.6-0.9 m (2-3 ft) deeper in the winter than in the summer. Thus, less cargo can be carried by the same size ship in the summer through the canal than in the winter. The Suex vessel is in the 71-81 kt (70,000-80,000 dwt) class. This larger vessel is able to transit the Suez since Egypt deepened the canal following the Seven Days War. Recently, the Suez Canal has been deepened to accommodate vessels with drafts as deep as 152 kt (150,000 dwt).

Jan 10, 1982

By I. Jashnani, J. R. Lawter, D. B. Lindsay

INTRODUCTION It is a generally recognized obligation of owners and operators of underground mines in the United States to protect the health of miners against the potential carcinogenic effect of airborne alphaemitting radionuclides, in particular the shortlived radioactive daughter-products of 222Rn. In meeting this obligation, a number of strategies are available, and it is largely up to the operator to decide what combination of methods he will use. Because the officially accepted theory of the mechanism by which radon and its short-lived progeny cause cancer of the respiratory system, the objective in controlling this health hazard is to limit as far as possible the inhalation of the three daughter products, 218Po, 214Pb, and 214Bi. (214Po, the fourth nuclide in the chain, is so short-lived that its alpha-decay occurs almost instantaneously after the beta-decay of its parent, 214Bi.) The reasoning in this theory leads to the conclusion that the alphadecay of radon itself causes essentially negligible physiological damage, and that the amount of daughter product activity attributable to decay of radon within the respiratory system is also very small. As every ventilation engineer in this business knows, however, focusing remedial actions exclusively on the daughter products themselves is choosing the hard way, and will probably never lead to effective control of this health hazard in underground mining activities. The reason for this troublesome fact can be seen in Figure 1. Let us say that we have air containing 222Rn and its short-lived daughters in near-equilibrium, a not-uncommon condition in the air of a poorly ventilated underground mine, and that we wish to purify it by removing only the toxic daughter products. If we have been very thorough in our purification efforts, we might expect to achieve a 99% reduction of the Working Level (WL) measurement. Figure 2 allows us to examine closely the early regrowth of WL's in this freshly cleaned air. Within the first five minutes, for instance, the WL's are back to 10% of their full equilibrium value, and ten minutes later the level has more than doubled and is on its way to an almost complete defeat of the clean-up effort by the end of the next hour. It is quite clear from this simple illustration that no matter how effective an air-cleaning system may be if it is directed only at the selective removal of the toxic trio, 218Po, 214Pb and 214Bi, its beneficial effect will be quite temporary. A truly effective attack on the problem must always include methods aimed at the control of the unruly parent, radon. Then, even if its progeny have an inalienable "right to life", their brief lives will not be spent in the miners' lungs. The object of the present paper is to show how state-of-the-art environmental air

Jan 1, 1981

By Michael L. Cramer, Kunsoo Kim

INTRODUCTION The Columbia River Basalt beneath the Hanford Site is one of several rock types being considered by the U.S. Department of Energy for the first commercial high-level nuclear waste repository. The Basalt Waste Isolation Project (BWIP) has been carrying out a comprehensive investigation to assess the feasibility of constructing a repository in basalt and to develop technology required for repository engineering and site characterization. Development of a nuclear waste repository requires a number of design considerations not usually necessary in the planning of conventional underground structures. Principal among these is the thermally induced stress field resulting from waste emplacement. This thermal stress, super- imposed on the preexisting in situ- and excavation- induced stress fields, needs to be evaluated in the design process due to the sensitivity of waste emplacement density to this factor. The nature of this thermally induced stress field is dependent on several factors, including the temperature distribution around the repository openings, the thermal properties of the rock mass, and the deformability of the rock mass. Re1iable performance of the repository structure is largely determined by the ability to under- stand the above rock mass characteristics and predict the underground opening response to waste emplacement based on this understanding. To gain an understanding of this rock mass behavior in a repository condition, the BWIP has conducted a large-scale heated block test in basalt at the Near-Surf ace Test Facility (NSTF) on the Hanford Site. This paper presents the results from the elevated temperature phase of the block test in which the thermal, mechanical, and thermo- mechanical response of the closely jointed basalt rock mass was evaluated as a function of stress and loading orientation at varying temperatures up to 200 oC. SITE GEOLOGY The NSTF test areas, including the block test site, are located in the entablature zone of the Pomona basalt f low. The Pomona flow entablature is structurally typical of most flows in the Columbia River Basalt Group in that it is characterized by long, undulating, polygonal columns up to 2.4 m in length. Columns vary from 15 to 30 cm in diameter, averaging about 20 cm. Over their length, columns can vary in dip by 150 to 200. The column structures are dissected by subhorizontal cross joints that are generally discontinuous and seldom cross columnar joint boundaries. Spacing of the cross joints also averages about 20 cm. A representative joint pattern taken from mapping of the tunnel wall near the block test site is shown in figure 1. Application of the Rock Mass Rating System (Bieniawski, l979) to the block test site yielded an overall value of 62. The corresponding value from application of the Q-system (Barton et al., 1974) is 8.7 (Cramer and Kim,1985). The NSTF is approximately 50 m below the surf ace. However, this depth is sti1l above the water table and conditions are generally dry. Interstitial water exists as the result of percolation of meteoric water from the surface.

Jan 1, 1986

By Thomas D. Kaufmann

Introduction What drives the price of gold? Supply and demand, of course. But in ways far different from the forces that drive the prices of other major metals, such as steel, aluminum, and copper. Gold, in fact, is one of the few commodities where both buyers and sellers are happy when the price goes up. Current production, production costs, and variations in production have little influence on its price. Gold inventories are so tremendous that current production has small impact on the amounts available to the market at any time. Worldwide gold inventory and production The world's inventories seem to be between 78 and 98 kt (2.5 and 3 billion oz). Since biblical times, the gold miners of the world have produced about 98 kt (3 billion oz), mostly in this century. Only small amounts have been thrown away and most of it - more than 78 kt (2.5 billion oz) - remain in bullion, coins, or jewelry. About 40% is held by central banks and other governmental authorities, 30% by private individuals as bullion or coins, and about 30% as jewelry. Except for some of the jewelry and the few industrial applications, this inventory is constantly available in marketable form at a price. By comparison, gold production is indeed small. The US Bureau of Mines estimates that the world produced 1.5 kt (50 million oz) of gold in 1986. Consequently, production increased world inventories by only 2%. Variations in production have a negligible or very short-term effect on the supply and, consequently, on the markets for gold. Although South Africa mines about 40% to 50% of the world's annual production, continuing labor strife there does not seem to have ruffled gold prices. Determining gold's price Gold prices, however, do determine cutoff grades in the mines and, thus, do influence production. Nonetheless, changes in production have little impact on the inventory supply. Consequently, it has small influence on the price of gold on the market. With a fairly stable supply, price changes are driven by changes in its demand. Unlike other metals, very little of the demand for gold comes from industry. Dental, electronic, and other industrial uses for gold consume less than 46.6 t/a (1.5 million oz per year). It would be safe to assume that such uses are less than 124 t/a (4 million oz per year) for the entire world. Variations in the 124 t (4 million oz), compared to a supply of 78 kt (2.5 billion oz) of supply can have only a negligible effect. Production net of industrial uses adds perhaps 1% annually to world inventories. This could, in time, affect markets. The increase, however, is mostly absorbed by population growth - more people wanting to own gold - and by gold being put in more attractive forms, such as coins. As an ancient Lydian king discovered, minting bullion permits

Jan 9, 1987