Search Documents

By C. Patrick

Annually, the US coal industry generates and must dispose of over 200 million st (180 million t) of coal refuse, expanding a major environmental problem. The purpose of this research was to investigate the feasibility of utilizing coal refuse as an aggregate in concrete. This paper reports on findings of the initial phases of a project to determine the viability of replacing traditional concrete blocks with refuse blocks for use in ventilation stoppings in underground mines. Refuse, collected from three active preparation plants in eastern Kentucky, was used as the primary as aggregate in the preparation of concrete cylinder. Stress-strain analyses on the refuse cylinders yielded compressive strengths of from 59% to 77 % of the control-group strengths. Low variability within the groups was found while significant differences between the groups existed. On-going determinations of the effects of weathering on the refuse cylinders is being conducted and will be completed in early 1995. The research results are favorable for the future direction of the overall project objectives.

Jan 1, 1997

By J. Derwin King, Harrison R. Cooper

Applications of nuclear magnetic resonance (NMR) offer possibilities for on-line sensing of the concentrations of several elements in flowing sample streams. In addition to hydrogen, these elements, generally of low-order atomic number, include aluminum, phosphorus, fluorine, sodium, boron, and lithium contained in minerals having commercial importance. Many such elements have been difficult or impossible to successfully measure on-line using the more familiar X-ray fluorescence and neutron activation analysis techniques. The availability of practical on-stream analysis methods is essential to applying advanced controls to processes incorporating these elements. On-stream NMR instrumentation has been demonstrated in the past for several process applications including, as an example, coal flow and analysis; and the technology has recently been extended to the measurement of phosphorous BPL in Florida beneficiation plants. The technique involves simultaneous sensing of proton (hydrogen) and 31P intensities to provide data for continuous calculation of BPL in the phosphate through calibration to volume fractions of water and solids. Initial operating results are described using the PhospholyzerTM on-stream phosphorous analyzer designed for plant application.

Jan 1, 1990

By A. T. Weber, G. T. Adel

Earlier studies on the hydrodynamic interactions between fine particles and air bubbles have shown that fine particle flotation can be improved by using small air bubbles. In the present work, microbubbles ranging in size from 70 to 250 microns have been used in a flotation column for the processing of fine coal. The performance of the microbubble column has been studied as a function of wash water addition rate, aeration rate, feed rate and column length to diameter (L/D) ratio. The information collected from these tests has been used to analyze column behavior and to develop scale-up criteria. The results of this investigation suggest that mixing within the column may not be as significant as bubble size and residence time in determining column performance. Improved recovery can be obtained by decreasing bubble size which increases the flotation rate constant, and also by increasing L/D which increases residence time for a fixed column volume. The increase in residence time with L/D is due to a decrease in the volumetric flow rate of wash water with column diameter.

Jan 1, 1988

By Donald P. Richards, William M. Greenslade, Daniel E. Albers

INTRODUCTION The application of oil field technology to large diameter hole drilling is beginning to offer a cost effective alternative to conventional shaft sinking methods. The drilling of ventilation and small production shafts are, of course, not new. The major constraint to the drilling of large diameter production shafts has been the inability to drill holes large enough and straight enough to install and operate relatively high volume hoisting equipment. This paper discusses recent advancements in drilling technology as applied specifically to large diameter holes for use in the mining industry. The paper emphasizes the geotechnical and hydrologic considerations in assessing site conditions and their application to drilled shaft technology. The authors worked together on a recent feasibility study for a 6 m (20 ft.) diameter 975 m (3,200 ft.) drilled shaft in New Mexico. Their individual experience in drilling and geotechnical investigations related to shaft sinking is world wide. DRILLING TECHNOLOGY Large diameter hole drilling has been a natural evolvement of oil well rotary drilling techniques. Most problems that were encountered in the rotary drilling of large diameter holes have been

Jan 1, 1981

By James J. Scott

Introduction Friction Rock Stabilizers, trade name Split Sets, are presently under research and development by Ingersoll-Rand Company and Dr. James J. Scott, inventor. Conceived in 1953, the system is a patented process undergoing extensive field and laboratory testing. The author has published papers on the Split Set System earlier (References 4, 5, 6) The Split Set System holds promise to be a revolutionary development in the field of ground control. The system produces an interior reinforcement to a rock mass which: 1. Is simple in its concept. 2. Adjusts to the degree of restraint needed to match rock properties. 3. Provides a yieldable support and, later, a more rigid support as it is needed. 4. Pre-loads the rock in compression to increase stability. 5. Is a full-contact, fully tensioned device to resist rock loads. 6. Minimizes the stress concentration effects inherent in many interior support devices. 7. Improves safety for the miner. 8. Is cheaper than a grouted system. 9. Offers the rock mechanics engineer an opportunity to design in a fashion not before possible.

Jan 1, 1977

By Jianping Sheng, Francis Otuonye

The potential for methane and coal dust explosions in underground coal mining operations has increased in recent years with the introduction of fast coal-cutting machines. Dust explosions usually follow accidental ignition of a methane pocket. The dynamics of the explosion may be strong enough to pick up and disperse coal dust deposited on mine surfaces and ignite the mixture. A self-sustaining dust explosion can then develop and propagate at large distances. Ignition of dusts can result in a fire, and this may also lead to a dust explosion if the burning dust becomes airborne. Entrainment of dust and the resulting dust concentration in the gas stream are some factors which determine the features of the subsequent explosion and flame propagation. A model of coal dust transport in the gas stream due to the initial explosion is presented. In this model, equations for the conservation of mass, momentum and energy are coupled with the convective-diffusive model of dust transport. The system of equations is solved numerically to obtain dust concentration, convective velocity and gas pressure profiles.

Jan 1, 1989

By R. L. Grayson, S. Yuan

A stochastic model for evaluating the impact of the reliability and maintainability of shovels and trucks on the operational effectiveness of shovel-truck mining systems is presented. In the model, the Markov modeling technique is used to analyze the operating status of a shovel-truck mining system. Then, simulation is used to study the productivity of a shovel-truck system in a particular state. Finally, the relationship between the effectiveness of a shovel-truck system in terms of productivity and the reliability and maintainability of equipment is established. This relationship may be very useful to mine managers in making decisions in surface mining (e.g., regarding production process control, equipment replacement, and maintenance planning). A quantitative study is given to demonstrate how the reliability and maintainability of equipment affect the system effectiveness and how to pinpoint the parameter that has the most significant effect on the system effectiveness. The quantitative study indicated that in order to improve the system effectiveness significantly, the reliability and maintainability of the equipment need to be improved simultaneously.

Jan 1, 1995

By P. J. Brown, R. W. Nice

The Thalanga Copper-Lead-Zinc Concentrator in Northern Queensland was commissioned in early 1990. The design of a flotation process for the sequential production of separate copper, lead, and zinc concentrates has always been a most formidable mineral processing challenge. In 1988-1989 during the process design phase, sized fractions of various samples were subjected to quantitative and qualitative mineral analyses. These analytical techniques are collectively known as modal analysis. Modal analysis aided in the selection of key process treatment parameters for the initial laboratory testwork on the Thalanga ore. The work also guided the flowsheet development and quantified the mineralogically imposed limitations on the separation process. This paper describes in general terms how these modal techniques were used to guide the program of laboratory flotation testwork which constituted the flowsheet design phase of this project. During these design studies, the primary grind and regrind requirements were deduced and the basic flowsheet configuration selected. Recent operating plant performance data are to illustrate the value of modal methods in addressing complex metallurgical separation problems.

Jan 1, 1995

By A. Shtiza

This literature review discusses the role of the Albanian institutions, the natural resources industry, potential investors and stakeholders in order to provide a set of indicators that can help to monitor amelioration within sustainable development principles. A map with the potential prospects of the natural resources will be a first step in identifying the further potential for exploitation. Mineral resource policies and governance, sustainable processing and supply chain as well as environmental management information system are some of the crucial tools identified, that will help to set up the indicators and quantify the achievements in environmental management in Albania. Moreover, the integration of practices that will support institutional capacity building; follow-up practices; the mainstreaming of global environment into planning; and the compliance monitoring process will additionally improve the environmental situation in Albania. Aligning business strategy with environmental policy, socio-economic analysis, environmental auditing are decisive tools in order to provide the Albanian authorities with a clear overview of the economic costs and the social benefits for sustainable development.

Jan 1, 2011

By Bruno Bussière, Michael Aubertin, Robert P. Chapuis

Covers with capillary barrier effects (CCBE) have been used in recent years as gas barriers for the isolation of wastes, including reactive mine tailings. Capillary barrier effects help to maintain a high degree of saturation in the moisture retaining layer, which then reduces gas flux. Various factors affect the degree of saturation of the moisture retaining layer in a CCBE, such as the material water retention characteristics and layer thickness. Slope geometry can also influence the hydrogeological behaviour of a CCBE, but this factor has frequently been ignored in the past. In this paper, the authors show some results of a numerical study that illustrates the influence of slope on the behavior of capillary barriers made of different types of material. The numerical model calculations are based on an actual case of a CCBE constructed in northern Quebec. This investigation shows that the water content profile is greatly affected by the position along the slope. Thus, it is necessary to evaluate the influence of the geometry to properly establish the performance of a cover system.

Jan 1, 2000

Bigger is indeed better in today's surface mining operations. That is especially true regarding haul trucks. Building larger, "supersize" trucks, however, means designing more powerful engines and drive systems that are also more efficient and environmentally friendly. And miners are demanding that these trucks have longer service lives with minimum maintenance. So truck makers are teaming with engine manufacturers and mining customers to design these larger trucks that will ultimately lead to reduced mining costs. About 180 of those truck makers, engine designers and miners gathered in Tucson, AZ in September to discuss the state of haul trucks in today's mining environment. Haulage 2000 was sponsored by World Mining Equipment and attracted attendees from around the world. Manufacturers described the latest in haul truck advancements. These included the design of more powerful engines, improvements to mechanical and ac and dc drive systems and suggestions on how to reduce maintenance spending. Technology improvements in tires for larger struck was discussed as was the cost efficiency of new, lighter-weight bed liners. The following is a summary of a handful of the presentations.

Jan 1, 1997

By O. H. Tuovinen, T. M. Bhatti

Microbiological leaching has been used as an alternative approach to conventional hydrometallurgical methods of uranium extraction. In the microbiological leaching process, iron-oxidizing bacteria oxidize pyritic phases to ferric iron and sulfuric acid, and uranium is solubilized from the ore due to sulfuric acid attack. If uranium in the ore material is in the reduced, tetravalent form (UIV), a red ox reaction is involved whereby uranium is oxidized to the hexavalent form (UvI) upon dissolution. In acid-leaching systems, the primary oxidant is ferric iron, which is reduced to ferrous iron by its chemical reaction with UIV. The ferrous iron thus formed is reoxidized to ferric iron by iron-oxidizing bacteria such as Thiobacillus ferrooxidans and Leptospirillum ferrooxidans. Nutritional requirements and responses to environmental extremes of acidophilic iron-oxidizing bacteria are appraised. The S-entity in Fe-sulfides is oxidized to sulfate by bacteria similar to Thiobacillus ferrooxidans and Thiobacillus thiooxidans. Pyrite and marcasite oxidation is a sulfuric acid forming reaction. Heap, dump and in situ leach techniques are feasible as bacterial leaching systems.

Jan 1, 2000

By Frank R. (Original by) Barnako

Coal mining historically has been a hazardous occupation but, in recent years, tremendous progress has been made in reducing accidental coal mine deaths and injuries. The purpose of this chapter is to discuss the basic principles of accident prevention as they are related to coal mining. Accident prevention fundamentals are no different for coal mining than for any other type of work. The fundamentals apply to all industries. Construction workers may be struck by falling tools and materials, and miners may be struck by falling slate and coal. Sailors may be trapped by shipboard fires, and miners may be trapped by mine fires. Railroad brakemen may lose hands and fingers positioning couplers, and miners may lose hands and fingers positioning couplers. Many other examples could be cited, but the point is that accidents that happen in coal mines are basically similar to accidents that happen in other industries. Thus, the basic principles for preventing accidents apply in coal mining as they do in any other type of work.

Jan 1, 1981

By A. Hoath, V. Paul, F. Haslam McKenzie

This paper considers mining ventures occurring in rural communities in Galicia, Spain and Western Australia, Australia. It compares and contrasts the communities where mining is taking precedence over other industries, examining the potential land use conflicts and the future of both the communities and the mines currently operating there. The Galician case study, Trevinca, is located 200 km inland and was once a primary producing area, notable for its scenic alpine landscapes, which have since been developed for small scale tourism purposes. The Australian case study, Boddington is located 100 km inland in what has been a highly productive farming area. Mining was a marginal industry in the case study areas but due to the comparative devaluing of agriculture and tourism and the increased value of mining outputs, mining has increased in scale and economic importance. This paper will consider the environmental, social and economic impacts that have occurred in both the case study localities. Where there have been land use conflicts, strategies for minimising the adverse outcomes will be considered.

Jan 1, 2011

By R. C. Milici

The primary factors that determine the marketability of coal from various supply centers in the U.S. are coal quality and supply; i.e. low sulfur, moderate- to high- Btu coals have large market areas when compared to less expensive but poorer quality coals. Price is the major factor in the competitive marketing of similar coal products. Good quality, (moderate- to high- Btu, low sulfur) coals from the Powder River and central Appalachian basins are marketed over large areas of the country, and central Appalachian coal is widely distributed in foreign markets, primarily as coking coal. In contrast, poorer quality bituminous coal (low calorific value and/or high sulfur) from the Illinois Basin, northern Appalachian Basin, and lignite from the Gulf Coast is marketed in or near the States in which it was mined even though the price at the mines may be lower than mine prices for central Appalachian coal. Widespread distribution of sub-bituminous Powder River Basin coal is enhanced by its exceptionally low mining costs, which offsets transportation costs to distant markets.

Jan 1, 2001

Power cable costs are only a small part of total mining costs. So many mine operators consider power cable failure and resultant downtime as part of the cost of doing business. But, viewed in terms of lost production, these costs can be quite significant. Now one company, Cablec, seeks to cut cable costs by upgrading the polymer compounding process used to make cable insulating and semiconducting materials. Cablec is the leading manufacturer of electrical power cables in North America. And with about a third of the market, Cablec is the largest supplier of power cable to the mining industry in the United States. To improve its products, Cable has entered the polymer compounding business. In July, it began producing insulator and semiconductor polymer compounds at its plant in Indianapolis, IN. "This new facility provides a quantum leap over conventional compounding methods," said Harry C. Schell, Cablec's president and chief executive officer. "The Cablec polymers plant is producing a dramatically higher standard of polymer compounds that provide significantly higher levels of performance and improved life cycle costs for power cable." Cablec faces tough foreign competition in the wire and cable business. Competing on price alone is difficult, particularly when foreign producers are state subsidized. So Cablec feels the best way to compete is to establish new quality production standards. The company's new polymers plant is one way to do this. By increasing purity control and uniformity in polymer compounding, Cablec says its power cables will last longer and fail less often. A typical medium voltage cable consists of a conductor, conductor shield, insulation, insulation shield, metal shield, and jacket. The conductor shield and the insulation shield are conducting polymers. Contaminants and imperfections can occur within the insulation, at the conductor shield/insulation interface, or at the insulation shield/ insulation interface. Over time, these contaminants and imperfections can decrease the electrical strength of the cable or cause premature cable failure. The effort to minimize the number and size of any possible contaminants begins with pure polymer compounds mixed in a clean facility. However, most power cable manufacturers manually handle raw materials, use ethylene/propylene (EP) in bulk bales, and mix polymercompounds in open Banbury mixers. The quality and uniformity of polymer compounds is also impacted by temperature variations in the mixing process. This results in wide gradations of product consistency from batch to batch and ultimately contributes to power cable failure. Cablec says the improved polymer compounds from its state-of-the-art plant will be the purest and most consistent insulating and semiconducting materials available. The plant itself RCA spent $18 million to build Cablec's Indianapolis plant. RCA used the facility to mix specialty polymer compounds used to make video disks. RCA had two considerations in mind for the plant, cleanliness and uniformity of the compounds. However, when the video disk market failed to materialize, RCA sold the 46.5 dam 2 (50,000 sq ft) plant to Cablec for $3.1 million. Cablec invested an additional $3 million for modifications and increased production capabilities. Today's replacement cost for such a facility is estimated at $30 million. Cablec says the plant will set a new standard for performance and be economically difficult to duplicate anywhere. One of the essential elements of the plant's clean process environment is the air intake system. It filters contaminants greater than 2 um, less than one-fiftieth the current industry standard. All material handling and conveying areas in the facility are air-locked. This keeps out contaminants such as smoke, dust, and pollen. Banks of pneumatic pumps move polymer components through the system and continually filter the air. The plant also has a backup air intake system. No process downtime due to pump failure here. From the time raw material enters the plant, it is stored, transported, and processed in filtered air by an airtight stainless steel system. The stainless steel resists rust and corrosion. This further eliminates the danger of contamination from paint or rust particles in the conveyance network. A computer system allows a single operator in a central control room to monitor every aspect of the compounding process from air quality to line speed. The computer

Jan 12, 1988

By W. M. Kidd

INTRODUCTION Uranium mine inspection in Canada forms one element of the enforcement of the Atomic Energy Control Act; it is under this Act that all Canadian uranium mines and mills are licensed to operate. Inspection duties are carried out by a small core staff of federal government inspectors (working for the Atomic Energy Control Board (AECB)) largely supplemented by provincial mine inspectors working on behalf of the AECB. Unlike most resource extraction in Canada, uranium mining is under federal jurisdiction and consequently it was the AECB who decided in 1975 that changes in the Canadian uranium mining industry, particularly its expansion and the expanding role of the mine inspector in the limiting of exposures, warranted the offering of a special radiation protection training course. The Uranium Mine Inspector Training Course (UMITC) was first conducted in 1976 at the Elliot Lake Centre in Elliot Lake, Ontario. Subscription for the course was not limited to mine inspectors to enable union stewards, management personnel and provincial/federal labour inspectors to attend. This paper will present an outline of the course content, the format of its presentation and non-curriculum aspects of running a course of this type in uranium-producing community. The core lecturers for UMITC are drawn from the Radiation Protection and Uranium Mine Divisions of the AECB. In addition, guest lecturers are invited from universities and medical research centres together with industry professionals and government researchers. In all some twenty-four plus presentations are made over the first five days of lectures. The program topic areas, hazards, controls, measurements, record-keeping and health effects are preceded by an intensive half-day session on radiation fundamentals. TOPICS Hazards [Dust] A review of the dynamics of airborne particles including the effects of particle size, gravity and wake-turbulence on the behaviour of dust clouds. Associated topics are migrational aspects of dust particles and specific dust-generating mine operations. [Radiation] Canadian uranium mines are increasingly diverse in nature ranging from large scale low-grade underground operations in Elliot Lake to smaller high-grade open pits in Saskatchewan. Papers are presented on assessments of internal and external exposure, the metabolic pathways of ingested or inhaled radiation and the specifics of mine and mill hazards. Radiation hazards are further broken down into gamma surveys of uranium mines, radon daughter concentrations and problem areas. Controls The relationship between mining methods and the operating environment is critically important to ensuring safe working conditions. This refers to both the selection of machinery/devices, etc., and to engineering controls which are instituted to remedy problems created by new technology. UMITC examines a number of possible mining techniques, their criteria for selection and impact on the working environment. Control measures, ventilation practices and design, the need for continuous water misting and special open-pit precautions are presented. These lectures frequently conclude with suggestions for better operating guidelines for mine ventilation systems and the need for greater co-operation between the ventilation department and the underground crews. Measurements Uranium mining regulations stress the need for a high standard of exposure monitoring, statistical planning and record-keeping. [Statistics] Although many course participants are well versed in statistics, certain fundamentals are repeated and include, the concepts of mean, variance, standard deviation and standard deviation of the mean. Confidence levels, decision-making based on sample statistics and statistical records are also discussed. [Dust Measurement] Dust measurement is particularly critical in the mines where the high silica content of the ore body, such as those at Elliot Lake, results in the continuous generation of dust. Sampling practices, filtration, impaction, thermal impaction and electrostatic precipitation are explained together with the methods of counting samples to determine free silica. Konimetric and gravimetric techniques for dust sampling are compared and contrasted. [Radiation Measurements] Both collective and personal dosimetry systems are used in the Canadian uranium mining industry and lectures are presented on each. Techniques and possible sources of error are discussed for a variety of radon and radon daughter measurement methods - Lucas method, Tsivoglou and modified Tsivoglou, Kusnetz, Rolle. Instant working level meters and personal alpha dosimeters are explained in terms of calibration, maintenance, readout and estimation of accuracy. A lecture outlining dose estimation by means of bio-assay, whole-body counting and the use of TLD's concludes the topic. Record-Keeping An overview of the problems of changing limits,

Jan 1, 1981

By L. J. Buter, D. J. Collins

Introduction FMC's Paradise Peak gold mine was discovered by staff geologists in July 1983. Located south of Gabbs, in western Nevada, the deposit contains about 11 Mt (12 million st) of ore grading at 3.6 g/t (0.105 oz per st) of gold and 129 g/t (3.75 oz per st) silver. It is estimated that the ore contains 34 t (1.1 million oz) of recoverable gold and 933 t (30 million oz) of recoverable silver. The 3.6 kt/d (4000 stpd) mill began operation April 14, 1986, just 18 months after Davy McKee completed a feasibility study and construction, and two-and-a-months ahead of schedule. It also came in about 10% under budget at a cost of about $100 million. Crushing Run-of-mine ore is delivered from the mine in 45-t (50-st) haul trucks to a 272-kt (300,000-st) capacity open air stockpile. Ore is reclaimed using 5 m3 (7 cu yd) front-end loaders that feed a 91-t (100-st) hopper equipped with a 610- x 610-mm (24- x 24-in.) grizzly. A 1.4- x 11-m (54-in. x 35-ft) apron feeder delivers ore from the hopper by way of a vibrating grizzly screen with 127 mm (5 in.) openings to a 1- x 1.3-m (43- x 51-in.) Rexnord jaw crusher. Crushed material is conveyed to a 1.8- x 4-m (6- x 14-ft) Link Belt vibrating screen equipped with a 50-mm (2-in.) manganese grizzly bar deck. Screen oversize is fed to a 1.7/0.6-m (5.5 ft) Rexnord standard cone crusher. Product from this crusher joins the -50 mm (-2 in.) screen undersize and is conveyed to a 136-t (150-st) surge bin. Three hydraulically driven belt feeders deliver ore from the ore bin to three 2 x 6 m (7 x 20 ft) Link Belt single-deck tertiary screens fitted with 6 x 25 mm (0.25 x 1 in.) slotted polyethylene screens. Screen undersize - -6 mm (-0.25 in.) rock - is conveyed to a 3.6-kt (4000-st) ore storage bin. Screen oversize is delivered by way of a conveyor to a 91-t (100-st) surge bin. From this bin, two belt feeders feed ore to two 1.7 m (66 in.) Rexnord Gyradisc crushers, which are in closed circuit with the tertiary screens. Design features include magnetic protection for tramp iron removal and sloping floors and pump sumps for ease of clean up. Dust scrubbers keep the working environment clean and in compliance with state dust emission regulations. Grinding Two 1 x 4.5 m (3.5 x 15 ft) belt feeders deliver ore from the fine ore bin to a conveyor belt that feeds it to the 5 x 7 m (16 x 22 ft) Allis-Chalmers ball mill. The conveyor belt is equipped with a Merrick weightometer. This controls feed rate to the ball mill by speed control on the hydraulic motors driving the feeders. The 2.6 MW (3500 hp) powered mill grinds 3.6 kt/a (4000 stpd) to an average grind of 85% -75 µm (-200 mesh). The mill is in closed circuit with four 660 mm (26 in.) Krebs cyclones. Three of these are normally in operation while one is a standby. Warman pumps feed the cyclones through a cyclone distribution manifold. The cyclone underflow returns to the ball mill, which has a 300% average circulating load. Mill discharge pH is 11, and that is obtained through pebble lime addition to the feed belt. Cyclone overflow is sampled using a Heath & Sherwood two-stage sampler. It then flows to a 27-m-diam (90-ft-diam) Eimco thickener. Thickener overflow is returned to the grinding circuit, while underflow at 50% solids is pumped to the leaching circuit. Grinding-circuit design features include a steeply sloped floor for ease of clean up, an open area over the pumps for maintenance accessibility, and a ball hopper with a self discharge bottom to speed ball addition. Other features include a mill liner handler and an air clutch that connects the mill motor to the mill.

Jan 12, 1986

By W. R. Dengler

INTRODUCTION Shaft sinking represents a relatively small proportion of the activities involved in mine development. Because of this limited utilization, shaft sinking has been one of the most difficult functions to mechanize. Although shaft machines (muckers) were introduced more than 30 years ago, the first machines were low-capacity units, and machines of this type did not gain wide acceptance by the mining industry until the late 1950s. However, the increasing depth of underground mines and the es¬calating costs of labor have increased the benefits obtain¬able from high-speed shaft sinking. The result has been a growing need for high-capacity shaft machines. Most of the machines available at the present time have been developed by modifying existing equipment to increase the payload capacity and performance. AVAILABLE SHAFT MACHINES In general, shaft machines may be classified accord¬ing to the types of digging mechanisms and the mecha¬nisms of operation. The available digging mechanisms include clamshells, cactus grabs, front-end buckets, and backhoes. The mechanisms of operation can be classified as either pneumatic or hydraulic. Selection Criteria For efficient operation, the primary consideration in selecting a shaft machine is its capacity. The minimum capacity of the machine should match the capacity of the hoisting system at the ultimate depth of the shaft. In many cases, two machines may be needed to obtain a sufficient mucking capacity. The shaft dimensions and configuration often dictate the type of machine that may be utilized; for example, an overshot loader does not work well in a circular shaft that has a diameter of less than 5.5 m (18 ft). Similarly, a single Cryderman mucker is not suitable for a large-diameter shaft, nor is it applicable where very high sinking buckets are to be used. Other factors for consideration include the degree of material fragmentation, the abrasiveness of the rock, and the amount of ground water that is inter¬sected. Machine Descriptions Riddell Mucker: The Riddell mucker, illustrated in Fig. 1, was first introduced in 1948. This is one of the most common shaft machines in the medium-capacity range. The Riddell mucker consists of a hoisting and traveling mechanism that operates a clamshell suspended on cables. The early machines operated with a 0.3 m3 (10 cu ft) clamshell and had an hourly capacity of approximately 27 t (30 st). This type of shaft machine has gained wide acceptance throughout North America. Essentially, the Riddell mucker consists of standard components, such as the pneumatic tugger hoists that operate the clamshell. The carriage is suspended on rails that also serve as the blasting set, located immediately below the shaft timbers. To effectively position the clam¬shell in the shaft, the operator controls the carriage travel by means of wheels that are driven by a pneu¬matic motor. The Riddell mucker most commonly is used in rec¬tangular timbered shafts. However, some units have been installed with circular rails, allowing them to work in circular concrete-lined shafts. A popular practice with many Riddell muckers is to increase the capacity through the use of larger clamshells, often ranging up to 0.76 m3 (1.0 cu yd), in conjunction with more powerful tugger hoists. In some large rectangular shafts, two Riddell units have been used side by side to achieve a sufficient capacity. Cryderman Mucker: The Cryderman mucker, illus¬trated in Fig. 2, is another common shaft machine in the low- to medium-capacity range. Developed in the early 1950s, it also has gained wide acceptance throughout North America. Equipped with a 0.3 m3 (10 cu ft) bucket, the Cryderman mucker has an hourly capacity of approximately 23 t (25 st). The Cryderman mucker is operated entirely by means of pneumatic cylinders and a pneumatic telescopic boom. The boom is suspended from a sectional frame¬work that is usually located at one end of the shaft. The framework or headframe can be suspended from an independent hoisting system located either on the sur¬face or in the shaft. In large shafts of either rectangular

Jan 1, 1982

By Theodore M. Gurr, James J. Bartels

Phosphate produced fertilizers provide the phosphorous nutrients required by plant life to sustain significant growth, thus improving the production of food for the world's population. Phosphorous replenishment of soil currently can be obtained efficiently by no other means than by direct application of phosphate fertilizer to the soil. Phosphate products are also utilized in animal feeds, detergent, and various industrial processes. Thirty-three countries are presently mining phosphate rock for the production of fertilizers, and its process byproducts. The major phosphate rock producers are the United States, the former Soviet Union, Morocco, and China [(Table 1)]. Phosphate rock is generally defined as a rock material that contains phosphate minerals which are sufficient for commercial usage. Phosphate minerals are found in sedimentary igneous and metamorphic rocks. Economic resources of phosphates are primarily developed from sedimentary rock sources. The apatite mineral family comprises the majority of phosphate constituents from both sedimentary and igneous rocks. Igneous phosphate rocks are generally composed of fluroapatite whereas sedimentary rocks are generally composed of carbonate fluroapatite, or chlorapatite. Phosphate rock is mined by a multitude of processes, including surface and underground mining. The mined rock requires mechanical and chemical processing to liberate the phosphate for utilization as fertilizer. Approximately 85% of the world's phosphate production uses sulfuric acid, with the remaining processes utilizing nitric and phosphoric acids. Ammonia is also introduced in the manufacture of liquid fertilizer, ammonium phosphate and ammonium polyphosphate. GEOLOGY Mineralogy and Chemical Properties Phosphate most commonly is derived from the mineral apatite, which is chemically described as CA5(F,Cl,OH)(PO4)3. Apatite is also broken up into the composite apatite minerals which are fluroapatite Ca5F(PO4)3, chlorapatite Ca5Cl (PO4)3 and hydroxyl-apatite Ca5(OH)(PO4)3. Carbonate CO3 can substitute for PO, forming carbonate apatite, called francolite. The guano phosphate (bird excrement) mineralogy commonly occurs as brushite CaHP04.2H20, monetite CaHPO4, whitlockite Ca3(PO4), and dahlite Ca10(PO4)6(OH)2. Apatite minerals form from igneous sources where they are developed deep in the earth's crust; and the cooling processes are slow, producing long, hexagonal prismatic to tabular crystals. The termination of the crystal can be basal plans or pyramids. In some instances, the crystals are bipyramids. Faster cooling, or sedimentary derived apatites are more commonly cryptocrystalline. Collophane is a name given to cryptocrystalline apatite found in phosphate rock in fossil form. Apatite minerals are relatively soft and are used to describe the 5 hardness on the Mohs scale. Cleavage is poor and develops along the C(0001). The color of apatite minerals varies from colorless, to violet, and blue, but are predominantly green or brown; luster is vitreous to subresinous. Collophane's physical appearance is often opaline, dense, with colloform structure and sometimes concretionary, nodular or pulverulent. Phosphate Bearing Materials Origins Phosphate deposits of igneous and metamorphic origins have been well defined. Sedimentary origins have been defined, but with a greater degree of uncertainty. Research in the 1980s proved out some of these processes through studies of real time deposition in Chile, Peru, and Australia. Igneous intrusive alkali rock and associated contact metamorphic rocks, provide approximately 20% of the world's phosphate. Fluorine containing apatite minerals are the most common materials containing phosphorous. Fluorapatite occurs in most igneous rocks. Fluorapatite and fluorine hydroxylapatite, together with carbonate varieties of these, are important members of the group. Where an essentially pure chlorapatite, carbonate apatite, and hydroxylapatite are rare and restricted in occurrence, the fluorine containing types occur in most all igneous rocks as early formed accessory mineral, usually in microscopic crystals, and may occur as extremely large bodies as magmatic segregations from alkalic igneous rocks. Apatite is also found crystallized in pegmatitic faces of both acidic and basic types of igneous rocks. More specifically, apatite is associated with magnetite deposits, in hydrothermal veins, especially those formed at relatively high temperatures, and in veins of the Alpine type. Apatite is common in both regionally and contact metamorphosed rocks, especially in the crystalline limestones where it is associated with sphene, zircon, pyroxine amphibole, spinel vesuvianite, phlogopite, talc, chloride schists, and as a contact metamorphic mineral.

Jan 1, 1994