Search Documents

By Anthony Peach, Lok Home

Introduction Raise boring is the most accepted form of mechanized hard rock boring in the mining industry. It appeared logical to take this mechanization one step further by introducing computers. Atlas Copco Jarva has produced a series of raise boring models that use an integrated computer. The company decided to use electronics and computerization, not for marketing purposes, but to make its equipment more cost-effective. Basis of Cost-Effective Design From the manufacturer's standpoint, it is possible for the equipment owner to reduce the cost of putting in raises by: • Replacing existing components with less expensive components that produce the same results; • Replacing existing components with more expensive components that make the equipment more productive; • Mechanizing equipment to reduce associated labor costs; and • Combining the above. Analysis of a standard raise boring machine (RBM) system showed that little could be done with less expensive components. It appeared, however, that the RBM could be more productive by transmitting more horsepower through the expensive drill string, while being precisely controlled by computers. An RBM system includes a basic machine, drill pipe, accessories, reamer, and cutters. The approximate percentage cost of various components on a standard system capable of boring 300 m (985 ft) long and 3-m-diam (10-ft-diam) aises in medium to hard rock is shown in Table 1. Also shown is the increased cost above standard of the Jarva computerized machine, and the productivity of both. Increased Productivity Penetration is important during the reaming cycle for more productive raise boring. This is possible by increasing the cutter load with constant rpm or increasing the rpm with constant cutter load. To increase thrust and maintain rpm requires increased capacity in the cylinders, drive train, main thrust bearings, drill string, electrical motors, and power units. To increase rpm and maintain cutter load requires only increased capacity in the electrical motors and power units. This is possible because the torque requirement remains constant for a constant thrust load. Only the horsepower increases, proportional to rpm. Since cutter costs are a big factor in raise boring, changes in machine performance must be analyzed to assess the effect on cutter performance. With a standard or typical carbide cutter, as used on raise boring machines, the effects of increased thrust or rpm are shown in Table 2. The assumption is made that the base data is the current rpm and thrust range where the cutters are now operated. It is also assumed one variable is held constant while the other increases. The result of this comparison, approximately, is that a 50% penetration increase can be achieved with little or no increase in cutter cost if rpm is increased 50% and cutter load is maintained constant. A similar 50% penetration increase can be achieved with a 45% increase in cutter cost, if the cutter load is increased by 20% and maintained constant. From an equipment standpoint, it is significantly less expensive to increase rpm 50% than it is to in-

Jan 7, 1984

By Beth Robinson

Central Mexico's mining districts, opened centuries ago during the Spanish conquest, still form the backbone of metal mining in the country today. Beginning at Chihuahua City, the Second Mexican Mining Rail Excursion traveled southeast from camp to camp through this major mining area to Taxco. Improved exploration, exploitation, and beneficiation methods have permitted continuous mining of many old deposits, and led to the discovery of new ones. Minerals not sought by early miners-lead, zinc, copper, and fluorite-now contribute substantially to mining activity in central Mexico. Of Mexico's five physiographic provinces, the rail excursion passed through two: the Mesa Central, and the Sierra Madre Occidental. The Mesa Central province is a wide tableland with basin and range topography, containing important base metal deposits. Mining in this region is primarily of limestone replacement ore bodies. Massive deposits form horizontal mantos or vertical chimneys. In northern Zacatecas, the Santa Eulalia and Naica mines demonstrated this character. The Sierra Madre Occidental lies west of Mesa Central in northern states, then widens to almost the entire width of the country from outside Mexico City to the southern border. The area consists of volcanic beds, several kilometers thick. These intermediate volcanics are primarily andesitic, of Tertiary age. Resting on older strata of adjoining physiographic divisions, the volcanic beds are overlain by a thick series of acidic flows and tuffs. Economic mineralization in the Sierra Madre Occidental is vein-type, primarily gold and silver. Mines at Fresnillo, Guanajuato, Pachuca, and Taxco contribute to the claim that this region is the center for precious metals in Mexico. A third type of mineralization, contact metamorphic deposits, is commercial at Santa Eulalia. First Stop, Santa Eulalia Mine tours began with the Santa Eulalia unit, located 25 km east of Chihuahua City. Mining in the region dates back to the early 1700s. The oxidation zone was worked until 1790, but mining declined until Asarco arrived in the early 1900s, building a selective flotation plant for treating primary sulfides. Asarco still owns 34% of Industrial Minera Mexico, S.A. (IMMSA), operator of the Santa Eulalia mine. Santa Eulalia currently has a milling capacity of 850 t/d. The San Antonio and Buena Tierra mines provide feedstock. Head grades at San Antonio, the mine participants toured, average 80-120 g/t of silver, 1.5-4.5% lead, 4-16% zinc, and 0.1-2.5% copper. Tin and vanadium were also recovered between 1930 and 1940. Estimated proven and probable reserves total about 7.6 Mt, although 1.8 Mt of reserves are located in areas of high water pressure and volume, which makes extraction difficult. Water is a significant production problem at the San Antonio mine. In one area, an AX drill hole encountered 2.6 m3/min (700 gal/min) at a pressure of 2.5 kPa. Precautions are taken to cope with the problem: protective drilling in advance of blasting is performed;

Jan 2, 1982

By Gordon M. Pugh, David G. Rasmussen

INTRODUCTION This method is a variation of cut-and-fill mining where either the wall rock or the vein is too unconsolidated to permit safe mining by conventional cut-and-fill methods. Basic development consists of driving a 2.4 x 2.7-m (8 x 9-ft) haulage heading laterally in the footwall side of the vein. Crosscuts are driven over to the vein at 91-m (300-ft) intervals. Then the vein, at each inter¬section, is mined out to a distance of about 9 m (30 ft ) above the track level. After the installation of an ore chute, scrams or intermediate drifts are driven in both directions along the vein. Mining then starts imme¬diately below the level bounding the upper limit of the stope. A cut varying between 3 and 4.2 m (10 and 14 ft) in depth and mined for a distance of 45.7 m (150 ft )along the strike is taken from the orepass in each direction (Fig. 1). In this mined-out void, the floor of the cut is equipped with 203 x 203-mm (8 x 8-in.) caps hitched into the wall with steel saddle hitches installed on 1.5-m (5-ft) centers. Double wood stringers, 152.4 x 152.4 mm (6 x 6 in.), are then installed on 1.2-m (4-ft) centers longitudinally down the length of the stope. Reinforc¬ing wire mesh is also placed, overlying each mat of timber. Directly above the stringers, stulls are installed from hanging wall to footwall to hold the timber in place during the sand-filling operation. Then a cement¬sand mixture in a ratio of about 1:10 weight is poured to a depth of about 2.4 m (8 ft). The entire cycle is then repeated down to the scram drift. Another variation of timbering is illustrated in Fig. 2. There is a vein width of approximately 5.5 m (18 ft) with the same unconsolidated ground conditions. The primary difference between handling this situation and the previously described undercut-and-fill method is that standard timbered sets are installed in each excavated stoping void rather than stulls. Once again the basic method is to work down the ore block from an upper timbered drift to a lower timbered drift. Cuts are taken from a timbered raise with a chute on the stope side. Each piece of ground excavated is essentially two sets high, 5.5 m (18 ft), by two sets wide, 5.5 m (18 ft), by the length of the cut along the strike of the vein. The timbered sets are 2.4 x 2.4 x 2.4 m (8 x 8 x 8 ft). The net result is, therefore, two sets of timber on a top floor separated by doubled-up 76-mm (3-in.) lagging from

Jan 1, 1982

By Milton H. Ward

The percentage of exploration dollars flowing out of the industrialized countries continues at an all-time high, and this shift in risk money is justified (Samuels, 1990; Bosson, 1977). Clearly, the odds of discovery are greatly enhanced if exploration is pursued in an untrampled and geologically more prospective environment. Unfortunately, such major unexplored areas of the developed world are shrinking rapidly, not just because the lands have already been tested, but primarily because they have been withdrawn from exploration. Experience, however, has shown that foreign investment is not without risks. These include problems that result from working in isolated areas, a lack of infrastructure, untrained workers and an absence of a solid geological data base. While the likelihood of once-feared expropriation is now low, mining enterprises still must take precautions to gain the support of their constituencies, including a variety of governments (local, provincial and central), workers, environmentalists, cultural organizations and local landowners. Is foreign exploration worth the risk? In most cases, Yes! But maintaining tenure and long-term success in a less developed country is only likely with good planning and the use of appropriate safeguards. These include measures such as buying country-risk insurance, building multinational relationships, forming joint investments, developing a broad customer base and seeking local investors in the company (Cobbe, 1979). The primary theme of this lecture is: How a company handles its constituency is critical to long-term tenure in a foreign country. Ideally, a multinational mining company would be so effective in dealing with the local people and managing its relationship with the host government that it would become a preferred employer, preferred over its competitors and over local companies. Historical overview Our earliest ancestors lived in Africa three to four million years ago. The Paleolithic or Old Stone Age, about 500,000 years ago, marked the beginning of mining in its earliest form (Gregory, 1980; Wolf, 1984). Various types of rocks and stones were used for tools and weapons, with flint being the preferred resource for implements. Initially, these materials were collected as stones (eoliths) lying on the surface. Then they came from excavations of flint in limestone beds that were exposed in river banks or naturally occurring excavations. Later, more formal mining developed. No doubt tribes of the Old Stone Age experienced conflict over rights to eoliths, food and land. The question of who owns the land and has rights to its contents and what is fair value for extraction is still the subject of intense debate and, occasionally, open conflict. As time passed, the search for useful minerals required migration from one area to another. Later, voyages from Europe to the New World and travels to other remote regions were funded and supported by absentee investors, kings and such (Rogers, 1976). The primary objective of such funding was to obtain gold, silver, food stuffs and other commodities that could be collected from the new countries. This is still the objective of foreign investment.

Jan 1, 1994

By Ying Lu, Jeffrey C. Johnson, Chen-Luh Lin, Jan D. Miller, Sindhoora Puvvada

Energy dissipation and fragmentation of rock is of interest for mine-to-mill operations in order to understand breakage and to minimize energy consumption during blasting at the mine site, and comminution at the processing plant. In this regard, high velocity impact breakage of long granite cores, called bars, has been studied with instrumented strain gages to follow the energy dissipation gradient along the bar length resulting from the strain waves generated by impact. As a result of high velocity impact, three zones have been identified (fragmentation, fracture, and elastic) and these three zones have been characterized in 3D using X-ray tomography. The fragmentation zones of the granite bars were studied in detail to describe the particle size distribution and the particle shape characteristics. Finally, the experimental energy dissipation for the fragmentation zone was found to be in close agreement with the expected energy calculated from the Bond work equation, if the anisotropic granite particles are defined by length rather than by sieve size.

By D. Akers

Many of the trace elements found in coal are associated with mineral matter, making it possible to remove them by physical coal cleaning. As part of work funded by the Electric Power Research Institute, both conventional and advanced coal cleaning processes were found to provide large reductions in the concentration of many trace elements that, if released into the atmosphere, are considered to be potentially toxic or environmentally harmful. Advanced physical cleaning technologies appear to provide greater reductions than conventional technologies. Chemical cleaning processes may also remove many trace elements, possibly including organically-bound elements such as beryllium. Care must be taken in the disposal of coal cleaning plant refuse because oxidation and leaching of this material can create highly acidic leachate and many trace elements are mobile in an acid environment. Laboratory leaching procedures are potentially useful in determining the degree of risk of water contamination by trace elements should an acid environment form.

Jan 1, 1992

By Yuanhong Qi, Xun Fu Wang, Tao Fu, Kunkun Cui, Yingyi Zhang, Jie Wang, Junmao Qie

With the sharp decrease of sulfide nickel resources, the nickel laterite is becoming more attractive as nickel oxide, nickel matte, and nickel-iron. This study investigated the mineral phase structure, chemical analysis, thermal properties, and element distribution characteristics of the rotten rock layer deposited in the Southeast Sulawesi Ophiolite Belt. The results show that the nickel laterite deposited in Southeast Sulawesi Island, Indonesia, belongs to the typical high-nickel and low-iron garnierite-type laterite. The concentrations of nickel and iron of the nickel laterite are 1.99 wt% and 17.55 wt%, respectively. The serpentine, olivine, clay, chlorite, hematite, and magnetite are the major minerals, and the pyroxene, actinolite, limonite, and chromite are the minor minerals in the nickel laterite in Southeast Sulawesi, Indonesia. Serpentine and olivine are the main nickel minerals with an average nickel concentration of 3.65 wt% and 1.73 wt%, respectively. The Fe and Ni have homogeneity and symbiosis in the serpentine and olivine, and their concentrations are often positively correlated.

By Gregg W. Davidson, J. Andrew McGlenn, Frank Huber

The Second Narrows Water Supply Tunnel will ensure system reliability in the event of a major earthquake and increase the Greater Vancouver Water District’s capacity to meet the long-term needs of a growing population. The tunnel will be 1,100 m long and 6.5 m in diameter (3,610 LF × 21.3 ft), constructed under Burrard Inlet between North Vancouver and Burnaby in British Columbia. It will be excavated through mixed ground conditions under high groundwater pressure, using a slurry TBM, between a 72 m (236 ft) deep shaft in soil and a 110 m (361 ft) deep shaft in rock. The completed tunnel will accommodate three large-diameter water mains that will be installed as part of the tunnel contract. This paper presents the project from design and contractor procurement, into the current construction stage describing some of the unique challenges encountered during the project development to date.

Jun 13, 2021

By K. Lang

The use of high-efficiency electrical submersible pumps (ESPs) for large scale, open pit mine dewatering operations provides a good example of how technology, products and services from the oil and gas industry can be adapted to the mining industry. In this case, the mine is Goldcorp?s Peñasquito in the Zacatecas state of Mexico, at the Peñasco and Chile Colorado open pit deposits. The technology, products and services are from Schlumberger artificial lift (AL) and Schlumberger industrial water services (IWS). Overview of high-efficiency ESPs This section provides a brief description of the basic components, specifications and operating capacity ranges for the ESPs compared with traditional or conventional dewatering well pumps. This information helps to establish how ESPs provide certain functional and economic advantages over conventional pumps in a mine dewatering application. A schematic of a high-efficiency ESP in an oil and gas (O&G) application is shown in Fig. 1.

Sep 1, 2013

By H. A. DeMirjian

Oil production rate and ultimate primary recovery from a heavy or viscous oil reservoir is usually limited to a very small fraction of the original oil in place. Typically, normal production rate is in the range of up to 10 barrels per day and expected ultimate cumulative production is up to 10% of in place values. Heavy oil reserves are not all alike. The physical properties of the rock, the liquid hydrocarbons, and depths of the deposits are so different that each reservoir poses a unique enhanced oil recovery problem. In some reservoirs thermal recovery by internal heat generation or external heat injection has been successfully exploited. In other reservoirs, mining the oil bearing formation for oil recovery by surface processing has been practiced. This paper will present an overview of the heavy oil recovery state of the art and discuss the critical factors leading to the decision for selection of a conventional hydrocarbon recovery or mining and extraction processes.

Jan 1, 1978

By Dongjie Zhang, Fengyu Ren, Xudong Li, Yanjun Zhou, Yang Liu, Rongxing He, Jianli Cao

Based on the limiting-equilibrium analysis of roof processive caving in hanging wall caving method and the critical medium column theory, a new model of subsidence prediction caused by sublevel caving mining method was proposed in this study, considering the drawing influence and the dynamic process of filling granular media. Meanwhile, the distribution rules for lateral pressure with different orebody dip were studied under drawing ore, and subsequently complemented the model. This model indicated that the surface subsidence scope decreased as the unit weight of crack rock and the orebody dip increased. In addition, the height of critical medium column showed a decreasing trend as cohesion of rock mass, the internal friction angle and the unit weight of rock mass. Also, the method of predicting the scope of surface subsidence in the Dabeishan Iron Mine was applied. The results showed that the relative errors are less than 9% and the prediction method could be used in practical application.

Feb 24, 2022

By Wilfred Walker

Much is known of the geography of the Alpine orogeny because it has now ended and all geosynclines are in their terminal, cordilleran form. The principle of sea floor spreading, continental drift, and mantle cells has gained general acceptance, but the number and position of the cells, even during the Alpine orogeny, is controversial. The oceanographers have demonstrated the uprises and in this paper it is suggested that downflows are marked by island arcs in the oceans and geosynclines (now cordillera) in the continents, for a total of about a dozen cells. Major mineral deposits associated-with the Alpine downflows are porphyry copper, molybdenum, nickel, chrome, lead-zinc-silver, gold, mercury, tungsten, and tin. Amore precise environment is known for some of these metals, for example, nickel, chrome, and mercury in flysch (which flanks mantle downturns), Ten major orogenies have taken place from 3500 m.y. to the present, Their re¬construction and metallogenesis is the subject of a continuing study.

Jan 1, 1971

By Frank A. Jerabek

Problems of mine backfilling and fill material deposited underground, the characteristics and relationship between the deposited fill material and overlying ground, and the practical applications and limitations of hydraulic backfilling as ground support are discussed. A great variety of materials ranging from coal washery refuse to concentrator tailings is used as hydraulic fill. Some materials will solidify and cement; others will resemble quicksand, Hydraulic fill as ground support is more efficient in inclined mine openings than in horizontal mine openings, where it cannot be placed tightly to the back. This and other deficiencies of hydraulic backfilling led to the development of pneumatic stowing. Research work in hydraulic backfilling at the Pennsylvania State University is also discussed. This research work includes the investigation of segregation in the discharged fill slurry, the quantity of solids escaping in the drain liquid, the relationship of escaping solids to slurry concentration and discharge rate, and the compressibility of fine fill material.

Jan 1, 1965

By M. Misra

The dielectric properties and flotability of different ranks of Argonne Premium Coal samples are presented. The flotability of different ranks of coal are correlated with the dielectric properties and intrinsic moisture (or bound water) content. Measured dielectric properties of as-received coals and other constituents are incorporated into a mixture equation to calculate the dielectric properties of bound water present in the different ranks of coal. The nature of bound water present in low-rank hydrophilic coals is significantly different from that present in high-rank hydrophobic coals. The water molecules present in low-rank lignite have an oriented dipole-dipole interaction and are tightly bound to the surface. For high-rank coals, the water molecules are not bound to the surface and have a randomly distributed clathrate ice-like structure. Controlled thermal treatment can modify the structural nature of bound water present in low-rank hydrophilic coals and increase their flotability.

Jan 1, 1990

By R. K. Sinha, B. S. Choudhary, Desh Deepak, A. K. Mishra, Hemant Agrawal, Shankar Kumar

There are several methods (empirical, statistical, and machine learning tools) to calculate blast-induced ground vibration. Still, due to complications in the blasting procedure, under varying blasting loads and strata conditions, it is not easy to predict and simulate blast vibration precisely. Therefore, a study was conducted to simulate the field blast data in Ansys software using explicit dynamics. For this study, monitoring of ground vibration for 20 single hole blasts was carried out. The density of emulsion explosives was in the range of 0.9 to 1.15 g/cc. In the laboratory, rock properties were determined from the rock sample collected from the mine site before blasting. The in-hole velocity of detonation (VoD) and the density of the emulsion explosive were also determined. These parameters were used for numerical analysis to know the ground vibrations at specified points. The results of ground vibration predicted by the model are validated using field data.

By S. A. Anzalone

The Helvetia copper deposit is a large undeveloped Laramide porphyry copper system located in the Santa Rita Mountains, Pima County, Arizona. This porphyry copper system consists of four areas of copper mineralization: Rosemont, Peach-Elgin, Broadtop Butte, and Copper World. Asarco refers to the four areas collectively as the "Helvetia Deposit". Mineralization and alteration are primarily contact pyrometasomatic, and zoning of hydrothermal alteration and sulfide mineral assemblages are similar to those observed at the Twin Buttes and Mission copper mines located approximately 32 km west of Helvetia. Asarco acquired the Helvetia Deposit in 1988 and has continued the exploration and development effort since then. A considerable amount of excellent geological work has been completed in the area but little information has been published on developments since the mid-1950's. The geology of the deposit as developed by numerous geologists over the past 75 years and the large, bulk tonnage low grade copper deposits outlined in recent years will be briefly reviewed in this paper.

Jan 1, 1992

By T. J. McKeon

Gravity separators such as spirals are commonly used in multistage cleaning and scavenging circuits to improve the quality and recovery of concentrates produced in the industrial minerals industry. Unfortunately, field surveys suggest that many industrial operations are poorly configured in terms of equipment layout. This shortcoming can often be attributed to a failure by engineers to make use of fundamental process engineering tools for circuit design. One of the most important of these is linear circuit analysis. This powerful tool makes it possible to mathematically compare the relative efficiency of circuit configurations in advance of experimental testing. This article provides a basic review of the linear circuit analysis concept and discusses some of the key insights it provides for the layout of multistage circuits. An industrial case study is provided to show the tremendous impact that this process engineering tool can have on the design of multistage spiral circuits in a heavy mineral wet plant.

Feb 1, 2012

By C. W. Newcom

The mining industry continues to be under expanded scrutiny in the health and safety arena, both from federal regulators and the media. While this paper will briefly discuss how enforcement activity, both with citations issued and the size of penalties proposed, the primary focus will be practical suggestions to deal with some key, high-risk areas for a mine operator which could have substantial impact, both in terms of liability and mine operations. It goes without saying that all mine operators need to continue compliance programs they have in place with careful ongoing evaluation of those plans for areas of improvement. The focus here will not be compliance as such, but rather steps to take and procedures to have in place to try to minimize risks in the face of the potential for more significant liability. Thus, our focus will be procedures to respond to unwarrantable failure citations, immediately reportable accidents, and to deal with potential pattern of violation issues.1

Jan 1, 2011

By David G. Chedgy

The Meadow River No. 1 Preparation Plant, owned by Sewell Coal Company, a subsidiary of the Pittston Company, was commissioned in the spring of 1974. The plant is designed to process 400 TPH of 5" x 0 raw coal. The 5" x 114'l fraction is processed in a Heavy Medium Vessel with the 114 x 28M reporting to Deister Tables for cleaning. The 28M x 0 fraction is cleaned in flotation cells, with the froth going to clean coal vacuum filters and the tailings to a static thickener where the underflow is reclaimed on Refuse Filters prior to disposal. The noise dosage a worker receives is determined by the ratio of the length of time the worker spends in a particular noise environment divided by the noise exposure in that particular environment. If the worker is exposed to several different sound levels, his total dosage would be the sum of each of the individual dosages. The equation for determining the dosage is: [ ]

Jan 1, 1976

By Noriyuki Fujii

It is no need to say that exploitation of industrial minerals has a close relation to development of the industries related. In the first stage, a small scale manufactures were initiated in areas producing some main raw material minerals. China and cement manufactures, for example, were established depending on the local occurrence of raw materials such as kaolin and limestone without exception. That is, the industrial development is greatly influenced by the local production of the raw materials in the stage. With the development of industrial technology, various kinds of raw material minerals are explored to meet the demands of industries in the second stage. New materials become indispensable, and low-grade raw material minerals, which were left as useless, are developed as useful materials. In the stage, the development of raw material minerals is accelerated by that of industrial technology related. However, industries mainly rely on domestic production of the min raw material minerals.

Jan 1, 1981