Search Documents

By T. L. Brekke, T. R. Howard

Stability of an underground opening can be defined in several ways. To geologists and engineers that are used to working in geological environments where the major parts of the works after careful scaling can be left unsupported during the construction period as well as during operation, any rock mass behavior that requires reinforcement, support or lining may be regarded as a stability problem. To colleagues excavating underground openings in geological environments that require continuous use of reinforcement or support and lining "stability problems" are often associated only with those parts of the work where "standard" construction procedure and method of reinforcement or support and lining is inadequate, and special measures therefore needed. In either case, a major objective is to assess the stability problems correctly -as far as possible at the planning stage -- and choose methods for excavation and reinforcement or support that will bring the opening safely and as economical as possible through the problem areas. INTRODUCTION It is not uncommon that stability problems associated with faults or seams have been described as "unexpected." This term has unfortunately been used to indicate that no one knew that the fault or seam existed prior to excavation. A careful review of documented cases where serious stability problems have occurred revealed that the existence of these zones most often was known, but that their behavior was incorrectly assessed prior to or during construction. Miscalculations have been made in terms of the type and magnitude of loads that developed, and in particular in terms of the time-dependant behavior.

Jan 1, 1997

By R. L. Brown

The Buchans mining district is located roughly at the center of the island of Newfoundland and contains some 18 separate mineral deposits. The first of these deposits was discovered in 1905, the latest discovery having been made in 1979. To the present (1983), some 16 Mt (17.7 million st) grading 1.33% Cu, 7.5% Pb, 14.5% Zn, 115 g/ t (3.7 oz per ton) Ag, and 1.4 g/t (0.04 oz per ton) Au have been mined. Mining operations are now largely terminated, but a few hundred thousand tons of economically marginal reserves may be mined in a salvage operation. The Geological Association of Canada Special Paper No. 22, "The Buchans Orebodies, 50 years of Mining and Exploration," contains papers which describe the history, geology, and the application of evolving geological concepts in exploration. Papers by Neary, Swanson, and Thurlow and Swanson in that volume are topical to the present discussion. Successful exploration techniques at Buchans included physical prospecting, utilization of the state-of-the-art geophysical techniques, saturation diamond drilling which was made possible by the high gross value of the existing ore, and, since 1955, diamond drilling directed by fairly well understood geological parameters. The record of discovery started in 1905 when the Buchans River deposit was found by Matty Mitchell, a prospector employed by the Anglo- Newfoundland Development Co., a British company which owned mineral rights over a very large area in the Red Indian Lake-Exploits River drainage system.

Jan 1, 1991

By Steven G. Vick, Herbert H. Einstein

1. INTRODUCTION The Tunnel Cost Model (TCM) is a computer based model whose objective is to quantify the risks of hard rock tunneling in terms of cost and time to completion. The main feature of the TCM is the simulation of the tunnel construction. The simulation makes it possible to incorporate in the time and cost computations the effect of uncertainties in geologic conditions and in productivity rates and costs. The cost and time computed with the TCM will be in form of distributions that allow a quantitative risk assessment. The TCM will be useful as an estimating tool permitting the estimator to rigorously relate uncertainties of individual factors to the end result. The TCM will also make it possible to evaluate technological innovations and to identify problem areas in existing technologies. The TCM consists of three interacting submodels: the geologic submodel, the construction operations submodel and the tunnel simulator. The goal of this paper is to describe the geologic submodel, whereas the construction operations submodel and the tunnel simulator will be described in the following paper by Moavenzadeh et al. First it will be shown how interactions between the geologic submodel and other parts of the TCM will impose certain requirements on the geologic submodel. These requirements, which relate primarily to the description of geologic conditions by a set of problem-oriented parameters and the quantification of uncertainty associated with geologic conditions, will then be discussed. This is followed by the description of the special structuring techniques -- decision tree and segmentation -- that are necessary to handle the great number of

Jan 1, 1974

By P. J. Macbeth, R. F. Overmyer, K. K. Nielson

INTRODUCTION Over the past several years, Ford, Bacon & Davis Utah Inc. (FB&DU) has been involved in research, development, and engineering activities concerning uranium mill tailings; specifically of interest in this paper are efforts in radon gas exhalation and surface flux attenuation measurements, environmental influences on radon fluxes, and basic research into radon gas behavior. Our projects have included measurements of effectiveness of specific cover material in attenuating radon surface fluxes from mill tailings, characterization of the parameters in cover materials and tailings that influence radon exhalation, long-term tailings stabilization planning, determination of the effects of moisture on radon emanation and diffusion from ores, and determinations of baseline radon fluxes. Our efforts have been sponsored by U.S. Department of Energy, the U.S. Nuclear Regulatory Commission, Tennessee Valley Authority, the commercial uranium industry, and we are presently engaged in efforts for the U.S. Bureau of Mines. Much of the material presented in this paper is taken from our published reports on radon flux attenuation and tailings stabilization (Macbeth et al., 1978; Nielson et al., 1980; Rogers et_ al., 1980; Thamer et al al., 1980). CHARACTERIZATION OF RADON GAS EXHALATION One dimensional diffusion theory based on Fick's laws is the basis for the modeling of radon gas migration through large quantities of porous tailings and cover materials applied over the large areas of tailings piles. Fick's first law relates the gaseous concentration gradients to the flux over the entire surface and defines the effective diffusion coefficient De as: [ ]

Jan 1, 1980

By Stephen G. Gemell

Gold mining has undergone a massive revival in Australia within the past decade. With very few exceptions, these operations are involved with the development of deposits which have been previously and partially worked by underground methods. In most cases, current operations have involved the open cut mining of near-surface remnants or low-grade hanging wall and footwall mineralisation. A growing number of mines are, however, progressing to the development of underground workings either as extensions of existing open cuts or as "stand alone" projects. These operations vary in scale from the Kalgoorlie operations of North Kalgurli Mines Limited and Kalgoorlie Mining Associates to the small scale "gouging" operations of individuals and partnerships. The individual production rates rarely exceed 200 000 tonnes per year, primarily because of the magnitude of reserves or the style of access available for rehabilitation. The narrow-vein mines were initially re-opened using the traditional methods, in particular shrinkage stoping and cut-and-fill stoping. As a result of experience gained in various ground conditions, certain variants have become popular. This paper investigates the fate of the traditional methods in Australian practice, and reviews some of the recently applied variants. This involves not only a perusal of current practices, but also an assessment of the influence of recent technological development on the economics of narrow-vein mining. Some consideration is also given to the effects of previously employed stoping techniques on efforts to access remnant blocks in the re-development of old mines.

Jan 1, 1989

By E. T. Sugar

English China Clays, the world's largest producer of China Clay, has its main production capacity in the South-West of England, where a complex of pits, refining plants, dryers and ports covers an area of approximately 100 square kilometres. The possibility of a computerised information network was first considered in 1980. The system was required to provide information at the central level and also at local plant level to improve co-ordination and control. Immediate access by any authorised user, and flexibility of interrogation were important aims. A small micro-based prototype system was implemented in 1981, and later that year development of the mainframe system commenced. This latter system will provide at least one terminal in every works location and will allow inter-communication of laboratory test data as well as detailed stock levels and production data. An integrated system for order processing will allow stock levels to be monitored in relation to anticipated requirements. The system has been developed by the Data Processing Department using the IDMS database package running on an ICL ME29 mainframe. It was decided to use microcomputers as terminals, which although more complicated because of protocol emulation allows stand-alone applications to be run on the same equipment. Those applications concerning Production Planning are outlined in the paper. Communication on the network is by synchronous transmission over dedicated lines. All data is stored on the central database with terminals accessing it in a star configuration. The system is currently partially implemented with 30 available screens at 18 separate worksites.

Jan 1, 1986

By Ashis Bhattacherjee, Subrata Chatterjee, Michael T. Dewey, Christopher J. Bise

In order to continue the advancements made during the past two decades in the reduction of the severity of accidents and injuries in underground coal mining, closer attention will have to be paid to the increasing number of accidents resulting in disabling injuries and lost time. With the increased emphasis on safety training reflected in the Federal Mine Safety and Health Amendments Act of 1977 (Public Law 96-1641, and on MSHA's current focus on the application of Job Safety Analysis, it appears that the acquisition, evaluation, and application of accident and incident data will take on an even greater importance. To manage this large amount of information will require a significant commitment of time and attention on the part of mine training departments. A USBM-sponsored research project is currently being completed at Penn State which focuser on the development of a model training program for mining. The program is based on five distinct steps which represent the coupling of a needs assessment with the program implementation. The five steps are: 1) database analysis, 2) workplace observations, 3) identification of trainable problem areas, 4) a library of training resources, and 6) the implementation of the program. In each of these areas, the microcomputer has proven to be a valuable tool for collecting, analyzing, and presenting accident and incident information. This paper will detail the manner in which microcomputers have been fully integrated into the model training program. Examples of applications at existing mines will also be discussed.

Jan 1, 1992

By Michael H. Leon, John A. Organiscak

Controlling worker dust exposure on longwall mining systems is difficult because the working face area serves as an immediate return during the mining cycle and the amount of airborne dust generated is directly related to production. Since improvements in longwall mining technology have significantly boosted production levels, additional technology is needed to control the airborne respirable dust generated at present and future production levels. One concept to reduce longwall worker's dust exposure is to maintain two splits of air at the face -- a clean intake split in the workers walkway, and a return (dusty) split over the face conveyor. The U. S. Bureau of Mines has recently investigated a concept to overcome the visibility handicap of face partitions by utilizing a permeable polyester mesh. The mesh material was anticipated to provide adequate air-splitting capabilities as long as the pressure differential between the face and worker walkway was minimal. Initial testing of this concept at the Bureau's Lake Lynn Laboratory showed that notable reductions could be achieved with a 1/8 in (3.18 mm) and 1/16 in (1.59 mm) mesh opening size. Dust reductions at 100 ft (30.5 m) and 200 ft (61.0 m) downstream of source were 58 and 36 pct, respectively, for the 1/8 in mesh and 79 and 55 pct, respectively for the 1/16 in mesh. Longwall application of the 1/8 in mesh showed similar results to the Lake Lynn Laboratory tests. A flame retardant mesh was used underground with portable lighting mounted on the shearing machine for face side lighting.

Jan 1, 1993

By G. Vik, P. Chryssanthakis, S. C. Bandis, L. Haruik, N. Barton, M. Christianson, A. Makurat

The large jointed chalk reservoir situated at 3 km depth in the North sea's Ekofisk field is undergoing major compaction after nearly 15 year of oil and gas production. Approximately 150 km 3 of the overlying sediments, mostly shales, are involved in the subsidence. A maximum central subsidence of nearly 3 meters, and a maximum present rate of 45 cm per year has set in motion numerous studies of the phenomenon. Non-linear finite element (FEM) and non- linear distict element (DEM) analyses of the compaction and large scale subsidence were performed. Consistent differences between the continuum and discontinuum analyses were noted. In the latter, slip on hypothetical bedding planes and sub- vertical or vertical faults was allowed, which possibly gives a more realistic simulation of the real processes of subsidence in such a large body of rock. Laboratory studies of the reservoir joints included roughness measurement, JRC and JCS characterization, direct shear tests while saturated in heated Ekofisk oil, and coupled closure-shear-flow tests with heated oil followed by heated sea water. Discontinuum modelling using Cundall's UDEC was performed on representative jointed assemblies (two sets of steeply dipping conjugate joints) to investigate the effect of a major reduction of pore pressure within the deformable matrix and along each joint. It was found that the large shrinkage deformation of the matrix allowed joint shearing to occur despite the constraint of uniaxial strain. Relative mass bulking due to small but widely distributed joint shear possibly explains the observed maintenance of excellent productivity despite large vertical strains in the reservoir.

Jan 1, 1986

By J. Loredo

Wastes related to abandoned mine sites can constitute important potential pollution sources, depending on their mineralogical and geochemical characteristics and volume. Mine waste disposal sites contain a diverse variety of wastes including overburden material and waste rocks, the ore which cannot be economically removed and wastes from the smelting processes when they are accomplished at the mine site. These materials are usually heterogeneous in size, mineralogy and metal concentrations. Asturias, in northern Spain, has an extensive mining history and, in consequence, there are abundant unreclaimed and derelict mine sites with abandoned mines and spoil heaps of different age, morphology, content and dimensions. In these spoil heaps, waste materials are subjected to the intense action of a humid environment, so the instability of sulphides and sulpharsenides results in the production of acid and metal-rich leachates, which are incorporated to surface water or infiltrated through the land reaching groundwater bodies. The mineralogical and geochemical characteristics of the stored materials are key data to evaluate if they represent an environmental risk. Mineralogy and geochemistry of wastes and the particular specific environmental conditions of each site affect the rate of weathering and therefore the metal release. The characterisation of mine wastes is a necessary step in order to establish suitable assessment strategies with the aim of reducing the leaching, transport and widespread of ecotoxic elements from mining wastes to the environment (surface water, sediments, soils and air). As a consequence of the weathering of As-rich mineral phases, high arsenic contents are commonly detected in effluents from mine voids and spoil heap leachates.

Jan 1, 2006

By Gregg A. Swayre, Roger N. Clark, Stephen J. Sutley, Kathleen S. Smith

Imaging spectroscopy is a relatively new remote sensing tool that provides a rapid method to screen entire mining districts for potential sources of surface acid drainage. An imaging spectrometer known as the Airborne Visible/InfraRed Imaging Spectrometer (AVIRIS) measures light reflected from the surface in 224 spectral channels from 0.4 - 2.5 µm. Spectral data from this instrument were used to evaluate mine waste at the California Gulch Superfluid Site near Leadville, Colorado. Here, the process of pyrite oxidation at the surface produces acidic water that is gradually neutralized as it drains away from mine waste, depositing a central jarosite zone surrounded by a jarosite + goethite zone, in turn surrounded by a goethite zone with a discontinuous hematite rim zone. Leaching tests show that pH is most acidic in the jarosite and jarosite + goethite zones and is near-neutral in the goethite zone. Measurements indicate that metals leach from minerals and amorphous materials in the jarosite + goethite and jarosite zones at concentrations 10 - 50 times higher than from goethite zone minerals. Goethite zones that fully encircle mine waste may indicate some attenuation of leachate metals and thus reduced metal loading to streams. The potential for impact by acidic drainage is highest where streams intersect the jarosite and jarosite + goethite zones. In these areas, metal-rich acidic dace runoff may flow directly into streams. The U.S. Environmental Protection Agency estimates (U.S. EPA, 1998) that mineral maps made from AVIRIS data at Leadville have accelerated remediation efforts by two years and saved over $2 million in cleanup costs.

Jan 1, 2000

By C. D. Mann

INTRODUCTION The sublevel stoping mining method is usually applied to a relatively steeply dipping, competent ore body, surrounded by competent wall rock. Ore is produced by drilling and blasting longholes, which can range from 50 mm (2 in.) to 200 mm (7% in.) diam, with lengths up to 90 m (300 ft). Longholes can be inclined in any direction, but the ring or pattern usually forms a plane, and the holes are blasted as a unit. Recently developed mobile drilling and loading machinery, as well as new explosives products, blasting techniques, and cemented sand and rock fill have made sublevel stoping a highly efficient and versatile mining method. When designing a sublevel stoping production sys- tem, it should be kept in mind that production rates from conventional sublevel stopes vary widely through- out the life of the stope. Early production is at a low rate, coming only from the drawpoints near the slot, but increases as new drawpoints are reached by the stope face. As the stope nears completion, again, fewer drawpoints are productive. Enough drawpoints must be available at any time to provide required production. Drawpoint availability should be compared to equipment availability; plan for more drawpoints than are needed at any one time. Accurate, realistic scheduling is essential to smooth production rates. Also, initial recovery of ore in a stope/pillar block is normally from 35% to 50% in sublevel stoping. Planning of pillar recovery, representing the majority of ore tonnage in a production block, must be done during early mine planning. Since much of the development already done for primary stoping (access for drilling, drawpoints, and haulageways), can be used for pillar recovery, early production from pillars is highly desirable. The following description of components of the system is an attempt to highlight some of the most important features and requirements of mechanized sublevel stoping methods. Similar comments would apply to the use of older equipment (column-and-arm drill setups, slushers, etc.) in similar methods. As in any good mining system, maximum economic recovery of the resource in the ground is the primary consideration. STOPE DESIGN CHARACTERISTICS Length and Width The following are some of the factors which affect sublevel open stope length and width dimensions: ore body geometry, principal stress directions, competence of stope back, optimum drill pattern, and drilling drift layout. In new mines initial stope layout design may occur before the ore body is actually intersected by mine workings. Stope dimensioning is a critical decision, and assistance from as many knowledgeable people as possible at this stage is essential. Operators with past experience in similar ore bodies, rock mechanics experts, and others with mine design experience should participate at this stage of stope planning. Height The following are some of the factors which must be considered in determining stope height: competence of stope pillar and stope/fill walls; slenderness ratio of adjacent pillars; ore body dip; ore body thickness; hole depth capability of the drilling machine; fragmentation characteristics of the ore; and level intervals in existing mines. In competent ground, drill-hole length and accuracy are the most important determinants of stoping height. Frequently entire drilling sublevels can be eliminated because of the depth capability of sophisticated drilling equipment, resulting in significant development cost savings. Drawpoint Location and Design Some of the most important considerations of a good drawpoint system are optimum spacing of draw- points, within the constraints of stope dimensions, for uniform drawdown and maximum recovery; excavations designed for stability for the life of the ore block to be drawn-primary stope ore as well as subsequent pillar ore; floor or roadway design including type of surface, reinforcing, grade for water runoff; orientation with respect to the main haulageway, for optimum loader maneuverability and ground stability at the inter- section; and length, to allow articulated front-end loaders to work in a straight configuration. Careful drawpoint design and construction are keys to successful production. Extra care in development, such as smooth wall blasting, rockbolts or grouted rebar, wire mesh, and shotcrete usually will ensure long draw- point life. Human exposure during production loading is of longer duration than during development or production drilling, and consequently preparation of draw- points is easily justified, particularly when pillar ore can be drawn through the same drawpoints. Secondary blasting of boulders can weaken drawpoints, also justifying good ground control techniques. A smooth draw- point floor of poured, reinforced concrete, on a grade of +3% or +4% toward the ore pile facilitates water flow out of the drawpoint, and ease of loader bucket penetration into the muck pile. Slot Raising, Slotting A slot or other space for rock expansion is necessary in conventional sublevel stoping where vertical rings or rows of holes are blasted. The slot can be started at a slot raise driven by conventional raising methods, raise boring, drop raising (predrilling and blasting a raise from the top, using small diameter-less than 200-mm (7%-in.)-holes for relief), or crater blasting (similar to drop raising, but without relief holes). The slot usually extends from the extraction level to the back of the stope. It is normally expanded to full stope width by

Jan 1, 1982

By John A. Breslin

Control of radiation hazards in mines is only one of many goals of the Bureau of Mines. Radiation research is only a small part of the Bureau's mine health and safety research program. In this paper I will describe the mission and programs of the entire Bureau of Mines, with emphasis on the mine health and safety program of which our radiation research is a part. The radiation program and its results will be described in detail by other speakers during this symposium. The Bureau of Mines was established in 1910 and is one of a number of agencies within the Department of Interior. Our mission is given by the Organic Act of the Bureau of Mines, last revised in 1913, which still accurately describes our work today. The amended Organic Act (Public Law 62-386) gives the Bureau authority "... to conduct inquiries and scientific and technologic investigations concerning mining, and the preparation, treatment, and utilization of mineral substances with a view to improving health conditions, and increasing safety, efficiency, economic development, and conserving resources through the prevention of waste in the mining, quarrying, metallurgical, and other mineral industries; to inquire into the economic conditions affecting these industries..." Since 1913 at least 52 public laws bearing on Bureau responsibilities have come into force. However, our basic role is still unchanged, i.e. improving health conditions, and increasing safety and efficiency in the mineral industries. The two principal activities of the Bureau are Minerals Information and Analysis and Minerals Research. The Minerals Information and Analysis programs provide the data base and the analytical capability to support the development of effective national mineral policies. Data on the availability, production, and utilization of minerals are collected, interpreted, and analyzed for some 100 commodities. Resources of the most important commodities are evaluated to support policymaking that influences utilization of the Nation's existing and potential mineral supplies. The President's budget for the Mineral Information and Analysis programs in fiscal year 1982 is $34 million. The largest activity of the Bureau is Minerals Research, which is divided into three major programs: Mineral Resources Technology, Minerals Environmental Technology, and Minerals Health and Safety Technology. The principal goal of the Mineral Resources Technology program is to help provide technology to maintain an adequate supply of minerals for the United States. The budget requested by the President for this program in fiscal year 1982 is $41 million. The goal of the Minerals Environmental Technology Program is to create mining and mineral processing operations that are more compatible with the environment. The budget for this program in fiscal year 1982 is $12 million. The largest program of the Bureau is Minerals Health and Safety Technology, which has the goal of providing the technology to protect the health and safety of mine workers. The budget for health and safety research for fiscal year 1982 is $55 million. Our radiation research is part of the health and safety research program. The Bureau of Mines has done research to improve health and safety conditions in mines since it was established in 1910. The research expanded greatly following the passage of the Federal Coal Mine Health and Safety Act of 1969 (Public Law 91-173) and the Federal Mine Safety and Health Amendments Act of 1977 (Public Law 95-164). These acts provided for increased health and safety regulatory activities, but they also significantly increased the funding available for mine health and safety research by the Bureau of Mines. Funding for the Bureau's health and safety research grew from $12 million in 1970 to $60 million in 1981. The funding in 1982 will be somewhat lower than that for 1981. However, the health and safety program funding is still approximately 40 percent of the total budget of the Bureau of Mines. Of the health and safety budget, 22 percent is spent on research to control health hazards in mines, including radiation hazards, which has a budget in 1982 of approximately $1.1 million. Other mine health hazards which the Bureau is doing research to control include respirable mine dusts which cause black lung and silicosis; excessive noise; toxic gases from explosives and diesel emissions; and excessive heat in deep hot mines. The other 78 percent of the budget is spent on safety research to prevent death and injury to miners from such causes as roof falls, fires, explosions, and accidents involving mining equipment. Over the past decade the majority of the Bureau's health and safety research has been done through outside contracts with private industry and universities. Our policy has been to do some research inhouse to maintain the expertise of Bureau personnel. Contractors are used to do research for which the Bureau does not have the necessary personnel available. The percentage of the program being done by contract has been gradually declining for the past few years, and in 1982 the program will be divided evenly between inhouse and contract research. The inhouse research of the Bureau is done at the 10 research centers located throughout the country. Our radiation research is done at three research centers, Denver, Spokane and Pittsburgh, and by contractors whose work is monitored by project officers at these centers. There are three Federal agencies involved in mine health and safety. These are the Bureau of Mines, the Mine Safety and Health Administration (MSHA), and the National Institute for Occupational Safety and

Jan 1, 1981

By N. R. Hasenmueller, V. Rajaram, R. K. Leininger, D. D. Carr

The content of the paper by V. Rajaram does not fulfill the expectations of the title. But Rajaram submitted the article in October 1983, and he could not have foreseen the numerous developments that would occur before his paper was published more than two years later. Nevertheless, Rajaram failed to mention the interest in oil shale development in southern Indiana beginning in late 1979 and continuing through the present as a result of special financial encouragement of three oil shale projects in May and August 1984 by the Indiana Energy Development Board and the Indiana Corp. for Science and Technology. A session at the 1985 Eastern Oil Shale Symposium in Lexington, KY, Nov. 18-20, 1985, gave the current status of oil shale developments in the eastern United States. Speakers at this session reported on the three Indiana projects. First, Gary D. Aho, Cliffs Engineering Inc., spoke on a feasibility study by Cliffs Engineering and Allis Chalmers for a site-specific pilot plant using the Allis Chalmers process. The plant site is in Clark County, IN, on property of the Midwest Energy Resources Co. The project is funded by $240,908 each from the Indiana Energy Development Board/Corp, for Science and Technology (EDB/CST) and the US Department of Energy (DOE) and $120,454 from the corporate sponsors (total $602,270). Completion is scheduled for mid-1986. Next, Edwin M. Piper, Stone and Webster Engineering Corp., discussed the American Syn-Crude/Indiana Oil Shale Project. This effort followed the completion of two smaller projects funded by the Indiana EDB/ CST: "Testing of Indiana Oil Shale in a Petrosix Pilot Plant" (total funding by EDB/CST at $50,000) and "Assessment of the Petrosix Process for an Indiana Shale Oil Plant" (total funding by EDB/CST at $100,000). The status at the time of the report at the Oil Shale Symposium was that a request for an extension of time for securing nonfederal support had been submitted to the US Synfuels Corp. The proposal included building an 11-m (36-ft) diam retort in south-eastern Indiana to process the New Albany Shale and to produce 366 m3 (2300 bbl) of shale oil per day by the PETROSIX process. The Indiana EDB/CST had contracted with Stone and Webster at $401,100 from EDB/CST and $245,835 from Stone and Webster for activities to advance the project in the negotiations with Synfuels Corp. At the time of the report, this project was the only eastern oil shale proposal that was still on the agenda of the Synfuels Corp. As a result of Congressional action in late December 1985, federal support from the Synfuels Corp. is no longer possible. Finally, Victor H. Carr, Eastern Shale Research Corp., described his firm's project, which is jointly supported by DOE ($227,749) and the Indiana EDB/ CST ($73,850) and is entitled "Feasibility Study to Determine Suitability of an In-Situ Process to Recover Hydrocarbons from Eastern Shale." An area in Scott County, IN, had been chosen, but not a specific 9 x 15-m (30 x 50-ft) site. One burn of a small in situ retort is contemplated as part of the project. Besides these three projects, several reports on shale research were presented. Joseph Damukaitis, American Syn-Crude Corp., reported that a pilot plant using the hydrogenation-extraction (H-E) process (described at the 1984 Eastern Oil Shale Symposium) was 94% built and would go through shakedown with oil shale but would then shift mechanical devices to process coal mine waste. Current status of research on the HYTORT process was then presented by Raymond C. Rex, Jr. Oil shale beneficiation research at the University of Alabama/Minerals Research Institute was reported by R. Bruce Tippin. Scott D. Carter discussed continued research on fluidized-bed retorting of shale at the Kentucky Center for Energy Research Laboratory. Carl E. Roosmagi of DOE, Morgantown, reported on the oil shale research at the Morgantown Energy Technology Center (METC) laboratory. Henry J. Gomberg, Ann Arbor Nuclear Inc., discussed "Radiation Combined with Donor Solvents for Extraction and Up-Grading of Kerogen." Aurora M. Rubel and coauthor Eileen Davis presented results of research at the Kentucky Center for Energy Research Laboratory under the title "The Effect of Shale Particle Size on the Products from the Bench Scale Fixed Bed Steam Pyrolysis of Kentucky Sunbury Shale." Lastly, Maria Rockwell, Technical University of Nova Scotia, presented "Processing and Up-Grading of Low Grade Nova Scotia Oil Shale for Potential Use." A review of shale oil prospects by Gerald Parkinson in Chemical Engineering for Feb. 3, 1986, covers both western and eastern projects and includes a report that the US DOE is funding a few relatively small projects; most of the fiscal 1986 budget of $12 million for shale oil is for fundamental research. Projects include a $3.2 million three-year contract with Hycrude Corp. (Chicago) for development of the HYTORT process and a $1.2 million three-year contract with the University of Alabama's Mineral Resources Institute on beneficiation of eastern oil shale by froth flotation. The report incorrectly states that current projects include a total investment of $466 million in a pair of 18-month technical and economic feasibility studies for proposed projects in southern Indiana. The correct figure is $468,657 [$240,908 for the Cliffs Engineering/

Jan 1, 1987

By V. Rajaram

R.K. Leininger, N.R. Hasenmueller, and D.D. Carr The content of the paper by V. Rajaram does not fulfill the expectations of the title. But Rajaram submitted the article in October 1983, and he could not have foreseen the numerous developments that would occur before his paper was published more than two years later. Nevertheless, Rajaram failed to mention the interest in oil shale development in southern Indiana beginning in late 1979 and continuing through the present as a result of special financial encouragement of three oil shale projects in May and August 1984 by the Indiana Energy Development Board and the Indiana Corp. for Science and Technology. A session at the 1985 Eastern Oil Shale Symposium in Lexington, KY, Nov. 18-20, 1985, gave the current status of oil shale developments in the eastern United States. Speakers at this session reported on the three Indiana projects. First, Gary D. Aho, Cliffs Engineering Inc., spoke on a feasibility study by Cliffs Engineering and Allis Chalmers for a site-specific pilot plant using the Allis Chalmers process. The plant site is in Clark County, IN, on property of the Midwest Energy Resources Co. The project is funded by $240,908 each from the Indiana Energy Development Board/Corp. for Science and Technology (EDB/CST) and the US Department of Energy (DOE) and $120,454 from the corporate sponsors (total $602,270). Completion is scheduled for mid-1986. Next, Edwin M. Piper, Stone and Webster Engineering Corp., discussed the American Syn-Crude/Indiana Oil Shale Project. This effort followed the completion of two smaller projects funded by the Indiana EDB/ CST: "Testing of Indiana Oil Shale in a Petrosix Pilot Plant" (total funding by EDB/CST at $50,000) and "Assessment of the Petrosix Process for an Indiana Shale Oil Plant" (total funding by EDB/CST at $100,000). The status at the time of the report at the Oil Shale Symposium was that a request for an extension of time for securing nonfederal support had been submitted to the US Synfuels Corp. The proposal included building an 11-m (36-ft) diam retort in southeastern Indiana to process the New Albany Shale and to produce 366 m3 (2300 bbl) of shale oil per day by the PETROSIX process. The Indiana EDB/CST had contracted with Stone and Webster at $401,100 from EDB/CST and $245,835 from Stone and Webster for activities to advance the project in the negotiations with Synfuels Corp. At the time of the report, this project was the only eastern oil shale proposal that was still on the agenda of the Synfuels Corp. As a result of Congressional action in late December 1985, federal support from the Synfuels Corp. is no longer possible. Finally, Victor H. Carr, Eastern Shale Research Corp., described his firm's project, which is jointly supported by DOE ($227,749) and the Indiana EDB/ CST ($73,850) and is entitled "Feasibility Study to Determine Suitability of an In-Situ Process to Recover Hydrocarbons from Eastern Shale." An area in Scott County, IN, had been chosen, but not a specific 9 x 15-m (30 x 50-ft) site. One burn of a small in situ retort is contemplated as part of the project. Besides these three projects, several reports on shale research were presented. Joseph Damukaitis, American Syn-Crude Corp., reported that a pilot plant using the hydrogenation-extraction (H-E) process (described at the 1984 Eastern Oil Shale Symposium) was 94% built and would go through shakedown with oil shale but would then shift mechanical devices to process coal mine waste. Current status of research on the HYTORT process was then presented by Raymond C. Rex, Jr. Oil shale beneficiation research at the University of Alabama/Minerals Research Institute was reported by R. Bruce Tippin. Scott D. Carter discussed continued research on fluidized-bed retort¬ing of shale at the Kentucky Center for Energy Research Laboratory. Carl E. Roosmagi of DOE, Morgantown, reported on the oil shale research at the Morgantown Energy Technology Center (METC) laboratory. Henry J. Gomberg, Ann Arbor Nuclear Inc., discussed "Radiation Combined with Donor Solvents for Extraction and Up-Grading of Kerogen." Aurora M. Rubel and coauthor Eileen Davis presented results of research at the Kentucky Center for Energy Research Laboratory under the title "The Effect of Shale Particle Size on the Products from the Bench Scale Fixed Bed Steam Pyrolysis of Kentucky Sunbury Shale." Lastly, Maria Rockwell, Technical University of Nova Scotia, presented "Processing and Up-Grading of Low Grade Nova Scotia Oil Shale for Potential Use." A review of shale oil prospects by Gerald Parkinson in Chemical Engineering for Feb. 3, 1986, covers both western and eastern projects and includes a report that the US DOE is funding a few relatively small projects; most of the fiscal 1986 budget of $12 million for shale oil is for fundamental research. Projects include a $3.2 million three-year contract with Hycrude Corp. (Chicago) for development of the HYTORT process and a $1.2 million three-year contract with the University of Alabama's Mineral Resources Institute on beneficiation of eastern oil shale by froth flotation. The report incorrectly states that current projects include a total investment of $466 million in a pair of 18-month technical and economic feasibility studies for proposed projects in southern Indiana. The correct figure is $468,657 [$240,908 for the Cliffs Engineering/

Jan 10, 1986

By Wallace Jarman

Introduction As with many gravity concentration processes, pneumatic concen¬tration traces its origin in antiquity. The use of winnowing to separate chaff from grain has long been known, and such procedures were undoubtedly practiced in ancient civilizations for the concentration of ores and the separation of slag from metal whenever specific gravity, size, and shape differences were favorable. Taggart142 has reported on the use of dry rockers and dry panning techniques for use with gold ores in arid regions such as Western Australia. The present day air table was developed in the last century for this purpose. Devices and Processes Classification. All classifiers make a separation on the basis of size, shape, and specific gravity. In addition to specific gravity and size, particle shape factor is often particularly important to pneumatic processes, and advantage is taken of the fact that both flat and fibrous particles settle at velocities substantially lower than that of their equiv¬alent spheres. Another factor of importance in this process is the bulk density of the material since substances such as exfoliated ver¬miculite or partially opened fibrils of asbestos have bulk densities significantly lower than those of the pure in situ mineral. Winnowing takes advantage of all of these physical factors to affect a separation starting with a closely sized feed, and vermiculite has been separated from rock by this process.142 When air classifiers are used to size minerals, the separation will often not be perfect because heavy particles will respond similarly to somewhat coarser light particles while flat, elongated, and low bulk density particles will act as would particles finer than the cut size. An example of a classification process that also results in concentration is the zig-zag classifier"' used to separate paper from glass, metal bottles, and cans during the recycle of municipal solid waste. Application of this process to minerals showing the proper specific gravity, size, and shape differ¬ences is obvious. An important device of this type is an air-aspirated screen used to remove asbestos from its associated rock during the dry processing of that mineral.144 The raw ore is crushed and screened and the asbes¬tos removed by aspiration from the surface of the screen by virtue of its shape and low bulk density. Hindered Settling. Based on the discussion in the section on "Hindered Settling Concentration and Jigging," the use of air devices could be anticipated in desert areas or where moisture may be deleteri¬ous to the product to be separated. Such processes have three major defects: (1) dust may be difficult to contain, (2) fines are difficult to process, and (3) the process is inherently less efficient than are wet processes as may be seen from Eqs. 3 and 4 in the section on "Hindered Settling Concentration and Jigging p. 4-47." Taggart142 has reported on the use of both dry panning and a dry rocker for gold separation in and regions. The dry panning makes use of winnowing, defection on the basis of specific gravity and shape during fall, and hindered settling. Prescreened placer material is poured from one pan to another as air blows across the falling stream. The process is repeated many times with hand picking to produce a rough concentrate. Magnetic minerals are then removed, and the residue, one grain deep in the pan, is air blown. In dry rocking the gravel is sized on a steeply inclined screen with the undersize fed to a riffle box with a porous bottom which is blown from underneath."' This device was the forerunner of the present-day air table. Air Tables and Jigs.145. 146 At least nine types of these devices have been developed, all but two of them for coal. While the devices used for coal may be characterized as pneumatic jigs, pneumatic tables, and pneumatic landers,145 only pneumatic jigs survive today. The same is true for ores.'" In these devices presized particles are fed to the separator which consists of an inclined vibrating conveyor with a porous surface through which air is carefully introduced to form a fluid bed. The lighter particles are lifted by the air out of uphill conveyance and float downhill, while the heavier particles in contact with the surface are conveyed uphill by the vibrator. Typically both transverse and longitudinal slopes are used. A plan view of a Triple S air table and the type of separation made is shown in Fig. 44.147 Because of its external appearance, the device has been called an air table, although it functions essentially as a jig. However, some of the asymetrical acceleration conveying function of a standard shak¬ing table is also performed by the eccentric vibrator incorporated into this device. Low pressure air is admitted below the vibrating table surface consisting of cloth (e.g., canvas), porous plastic, woven wire, or punched metal supported on a wire mesh or grid. As with a shaking table, the device produces a concentrate, middlings, and tailings. The middlings are recycled or are subsequently treated on another concentrating device. As with many wet separations, presizing by screening is necessary. The oft-repeated admonition of Professor Richards, "Separation without classification is damnation," is cer¬tainly true here. In this way a small heavy particle which might weigh the same as a large light particle and thus report to the same place on the air table has already been removed in the sizing step. Air tables are almost universally encased with a canopy to remove dust by aspiration. Some concentration may also be achieved in this step when favorable specific gravity, size, and shape differences are present. Applications Ore Separations. Air tables were originally developed for ore separations, and they find application in and regions or where water is deleterious or inconvenient to use or remove (e.g., small tonnage materials already dried). They have been used for asbestos, bauxite, calcite, cassiterite, columbite-tentalite, diatomaceous earth, fluorite, gilsonite, graphite, kyanite, manganese minerals, mica, managite, perlite, pyrite, pyrrhotite, vermiculite, and uraninite ores. More recently, air tables have found favor in separating a wide variety of secondary materials such as abrasive grains, bone char, catalysts, fiberglass, scrap glass, scrap wire from its insulation, prills from slag, dross and coke from metal or from each other, metal from crushed crucibles, lead from plastic in old batteries, and cubic particles from flat ones. The devices also finds considerable application in the preparation of food¬stuffs. As stated before close sizing before separation is desirable, and if the specific gravity difference is slight, very tight

Jan 1, 1985

By T. R. Ellis

"In August 2013, the Appraisal Practices Board of the U.S. Appraisal Foundation issued its “APB Valuation Advisory #4 - Identifying Comparable Properties,” which contains analysis and examples that may suggest a broader meaning of the term “comparable properties” than is current convention in real property value appraisal in the United States and internationally. The advisory is directed at the appraisal of real property of all kinds, including interests in mineral properties, as indicated by the inclusion of two mineral property appraisal papers in the appendix that lists suggestions for further reading.This paper firstly reviews as background the historical meaning of a comparable property, with its perceived constraints, against real-world examples of transacted mineral properties that are adjusted to subject properties to provide market value indications. The advisory’s findings are then examined and evaluated as to whether they may influence and benefit the work of mineral property appraisers, particularly in situations where their sales comparison analyses may be challenged. The conclusion is that the combination of constraints that the advisory’s findings specify for use of the term “comparable” will for mineral properties be met infrequently or rarely. As a result, mineral property appraisers are advised to avoid using the terms comparable or “comp” when referring to transactions of mineral properties that they analyze to derive data for appraising the value of their subject mineral properties. IntroductionA mineral property appraiser rarely finds a sale of a mineral property that meets the literal meaning of the term “comparable sale,” by being directly comparable to the subject property of the appraisal in all factors of significance in the determination of the value of the property interest being appraised. Real estate appraisers have long used a more liberal interpretation of the meaning of comparable sale and its commonly used abbreviation, “comp.” Real estate appraisers compare sales to their subject property on the basis of price per hectare or acre of land and price per square meter or square foot of building floor area. Adjustments totaling to within the range of +30 to -30 percent from the sale property to the subject, before factoring in the property area, have generally been viewed as appropriate for the sale to be considered a comparable sale."

May 1, 2016

By Michael Vitale, Lee W. Abramson, Daniel McMaster, Andrew J. Thompson

"Performing risk analyses on tunnel projects has become common place and on many projects it is required from an owner or regulatory perspective. After the project is planned, designed and constructed, the data concerning identified risks, assumptions, costs, probabilities and mitigations is generally long forgotten and buried in some file somewhere. A study was performed comparing predicted risks versus actual events on four recently constructed rock tunnel projects in New York, Ohio, Georgia and California. Probabilities and costs for selectively common risks on tunnel projects have been studied and re-evaluated. Conclusions are presented that can guide future projects and the veracity of the tunnel risk analyses performed. INTRODUCTION Tunneling is a risky business. More than ever, attention is being paid to the risks associated with tunneled facilities and implications on project or program cost and schedule. Questions about why tunneling projects notoriously exceed budget numbers abound. Evaluations in retrospect and going forward have focused on the wide breadth of inherent risks associated with tunneling. More and more, these risks are being identified, studied and managed to a higher degree. As more and more scrutiny pervades the industry, little value is being obtained and leveraged on future projects. The industry seems to be headed in a direction of making the same mistakes over and over. The notion of risk evaluation has been around for decades and received wide notoriety with the U.S. Space Program and ambitious projects in the energy industry such as hydropower and nuclear power in the 1960s and 1970s (Stewart and Melcher, 1997). This led to the evolution of tunnel risk analyses with more rigorous identification of the unique risks in tunneling projects impacting cost and schedule. As tunneling risks became more readily identified, more attention has been paid to the frequency and impact of the occurrences unique to tunneling (ITIG, 2012). Currently, few tunnel projects are being planned, designed or constructed without a formal risk register that identifies the risks, mitigates the risks and quantifies the probable impacts of risks that cannot be mitigated. In hind sight on many recent projects, events that brought projects to “its knees” were not addressed in risk assessments or were not dealt with to adequately mitigate the risk of these events."

Jan 1, 2016

By Steve Kral

"Liebherr, as most anyone involved with the global mining industry knows, is one of the world’s largest makers of mining and construction heavy equipment. The familyowned company has been around since the 1940s and, according to Stefan Heissler, by the end of next year, will employ about 44,500 people worldwide. Heissler is a member of the board of directors of Liebherr International AG.It all started for the Switzerland-based company when Hans Liebherr first recognized a need for heavy equipment in the construction industry, Heissler said. His first product, introduced in 1949, was the TK10, a mobile crane that, at the time, was a groundbreaking innovation to the heavy construction industry. From there, the company began its growth into a world-leading heavy equipment manufacturer that always relied on innovation.In October, Liebherr gathered a group of mining and construction magazine editors in Leoben, Austria to take a look at the company’s latest addition to the global mining and construction markets. On the mining side, Liebherr provided a demonstration of its T-236 100-t (110-st) haul truck and the PR- 766 50-st (55-st) crawler tractor. The one-day demonstration took place at the Erzberg iron mine near Leoben, where both machines are being proven.The Erzberg Mine, operated by VA Ersberg, has been in operation for about 1,300 years and is said to be Europe’s largest surface mine. It employs about 230 people and mines about 12 Mt/a (13,200 million stpy) of ore, producing about 3 Mt/a (3.3 million stpy) of fine-grained iron ore.T-236 rigid-frame truckThe new T-236 rigid-frame dump truck, with a diesel electric drive system, is Liebherr’s entry into the 100-t (110-st) class and is the first in this class with a four-corner, oilimmersed braking system. The haul truck was first introduced during the 2016 MinExpo in Las Vegas, NV. The unit has since successfully completed its testing phase and is currently in its first field operation trials at the Erzberg iron mine in Austria."

Jan 12, 2017

By J. Reyher, R. Bratton, G. Luttrell, B. Li

"Flotation is regarded as the best available method of upgrading minerals and coal fines. However, its efficiency deteriorates rapidly with decreasing particle size. Further, ultrafine concentrates are difficult to be dewatered economically, forcing companies to discard part of the ultrafine materials to impoundments. To overcome these problems, a new method of separating and simultaneously dewatering ultrafine particles has been developed. Following extensive laboratory-scale test work, the process, known as hydrophobic-hydrophilic separation (HHS), has been tested successfully in continuous operations at proof-of-concept (POC)- and pilot-scale tests. The results show that the HHS process is capable of producing high quality clean coal with high recoveries and low moistures. INTRODUCTION Coal preparation plants are designed with up to four parallel processing circuits for treating coarse (> 12 mm), intermediate (12x1 mm) small (1x0.15 mm), and fine (<0.15 mm) particles. The plus 0.15 mm fractions can be effectively cleaned efficiently with gravity separation methods (Wills, 2006). At present, the only commercially viable option for cleaning the finest fraction is froth flotation (Yoon et al., 1999). In flotation, air is dispersed in the form of small air bubbles in a tank in which coal fines are suspended. The small air bubbles selectively collect the hydrophobic coal particles and float to the surface, forming a froth phase which overflows into a launder. As is well known, ultrafine coal particles of less than 30-50 µm are difficult to be collected by the air bubbles, resulting in low recoveries. Furthermore, fine particle flotation suffers from low carrying capacities and poor selectivity due to entrainment problems. (Bethell et al., 2005; Luttrell et al., 2014). In addition, the froth products containing ultrafine coal are difficult to dewater. Mechanical dewatering in general becomes inefficient with decreasing particle size due to small cake porosity and high surface area, resulting in high moistures (Hucko et al., 1988). The cost often becomes prohibitive with particles of smaller than ~45 µm (Bethell et al., 2005). Moreover, the high-moisture products are difficult to handle and incur high shipping costs and lower thermal efficiencies (Honaker et al., 2013)"

Jan 1, 2016