Search Documents

By V. T. McLemore

Rare earth elements (REE) are becoming more important in our society. REE deposits are found throughout NM. Some REE past production (1950s), as bastnaesite, came from the Gallinas Mountains district, Lincoln County, NM. Several companies and the U.S. Bureau of Mines (USBM) have conducted exploration programs to identify REE potential. Four types of deposits are found in the district: epithermal REE-F veins, Cu-REE-F veins, REE-F breccia pipe and iron skarn deposits; all are associated with Tertiary peraluminous, alkaline to alkalic-calcic volcanic rocks. District zonation is defined by base metals (REE-F-Cu veins) that form center of the district, surrounded by REE-F veins. The magmatic-hydrothermal breccia pipe deposits form a belt partially surrounding the veins. Iron skarns formed at the top and edge of the trachyte intrusion and are likely the earliest stage of mineralization. In 1991-1992, USBM calculated an inferred resource of 0.487 million metric tons with a grade of 2.95% total REE. With the projected increase in demand of REE, areas such as the Gallinas Mountains district in New Mexico are being re-examined for additional REE potential.

Jan 1, 2011

By A. S. Ericson, J. H. Corrigan, E. J. Jahnsen

Calcine is transported from the Reduction Plant at 850°C in insulated hopper cars and charged into three rectangular electric melting furnaces each equipped with three - 18.5 MVA transformers. The electrical energy is applied through six in line prebaked carbon electrodes, and slag and metal are tapped at opposite ends of the furnaces on an intermittent basis. The slag, 5000 tonnes per day, is disposed of by a pot train directly to the dump. The ferronickel, 250 tonnes per day, is tapped into 40 tonne capacity ladles in which it is refined in two ASEA-SKF ladle furnace stations. Casting is done over lip at 1520°C in a pig casting machine with stepless speed control at up to 55 tonnes per hour. The ingots are stacked into self palletizing bundles weighing about 1500 kilograms and are strapped and tagged and transported to the seaport, from which the final shipment is made to the world market. The paper describes constructional details and gives information of both normal operation and start-up and shut-down procedures. Consumption figures for refractory, electrodes, electric energy and refining additions are given and metal chemistry is given before and after refining.

Jan 1, 1979

By T. J. Cox

The Red River is located within the Sangre De Cristo Mountain Range in northern New Mexico. An approximate 12-mile segment of the river from the town of Red River to the village of Questa (Questa) includes several hydrothermal alteration zones. Alteration ?scars? formed as a result of rapid chemical weathering and physical erosion of pyrite-rich hydrothermally altered rocks. Storm water runoff from the scar drainages contributes metal-laden, acidic water to the river and creates a visible plume of discolored water in the river. Acidic runoff reduces the river pH from 7 to the mid 3s for at least 2 hours during large storms and the low pH water continues downstream. Runoff from scar drainages increases some metal concentrations in the river from below chronic ecological criteria to as much as two orders of magnitude greater than acute ecological criteria, and results in acutely toxic conditions for macro-invertebrates. A general improvement in the river?s water quality occurs downstream due to dilution from tributary inflow from non-mineralized watersheds, the natural buffering capacity of the river, and storm water controls at the Chevron Mining Inc. Questa mine.

Jan 1, 2011

By L. R. Nelson

Cyprus Pima is a medium-sized open-pit copper mine located 35 km (22 miles) south of Tucson, AZ. The ore body was discovered using geophysical prospecting methods in 1953 and was originally worked as a small underground mine followed by small open-pit operations. As mining equipment grew larger and the economic ore grade dropped, the operation grew in size, through four expansions, to the present 50 500 tpd (56 500 stpd) milling rate. The remaining stripping ratio is about 2.5 to 1. Mining equipment includes 11 electric shovels ranging in size from 6 to 15 m3 (8 to 20 cu yd) and 42 diesel-electric haulage trucks ranging in size from 89 to 223 t (100 to 250 st). Mine planning is performed at Cyprus Pima to serve several functions. The most important is to plan ahead, one year at a time, to predict the ore grade and stripping requirements on a month-by-month schedule. This yearly plan is necessary for budget preparation and is revised once each quarter to incorporate variations in actual production experienced during the preceding quarter.

Jan 1, 1979

By Graham Swan, Richard K. Brummer

The paper begins by describing an underhand cut-and-fill mining concept for a 50m thick, generally tabular though irregularly shaped orebody dipping at 30 degrees and occurring at a depth of between 2300 and 2700m in the Sudbury Basin. From this, the broad design requirements of a fill system are stated. Two and three-dimensional numerical models are then described which were built to evaluate the theoretical benefits of different types of fill reinforcement. Included in this evaluation are the effects of span, fill strength, fill tightness, as well as static and dynamic loading types. Results, supported by large-scale physical models, are presented to show the significance of reinforcement on stable, undermined fill performance. Finally the paper describes work which has been done to evaluate the suitability of so-called silicated cemented backfill. This system is, in principal, attractive for deep mining applications since transportation is in the "safe" hydraulic regime, while fill water run-off, segregation and shrinkage effects are potentially eliminated in the stopes. The results from various surface and underground trial pours are reported which substantiate the proposed use of this type of backfill at depth.

Jan 1, 2001

By C. G. Janes, N. Finkelstein, L. M. Jr. Johnson

In May, 1966, the General Services Administration (GSA) announced a program to encourage additional domestic production of copper in the interest of national security. Upon learning of the copper production expansion program, Duval Corporation entered into negotiations with GSA for development of the Sierrita copper-molybdenum property under the program. Agreements between the GSA and Duval Sierrita Corporation, a wholly owned subsidiary of Duval Corporation, were concluded in 1967, with the Sierrita Concentrator beginning operation in 1970 at a designed capacity of 72,000 STPD. Subsequent additions and modifications have expanded capacity to 90,000 STPD. This property, located approximately 20 miles south of Tucson, Arizona, represents an investment including working capital of about $200 million. These funds were provided from an $83 million loan from GSA, repayable in copper valued at 38 cents per pound, $48.75 million of bank loans subject to U. S. Government V- loan guarantees, and Company capital contributions. Current general operating statistics for the concentrator are listed below: Ore Grade 0.32% Cu., 0.030% Mo. Daily Tons Milled 90,000 STPD Annual Copper Production 94,600 Tons Annual Molybdenum Production 15,000,000 Lbs. Annual Silver Production 1,135,000 Ounces

Jan 1, 1976

By Harry R. Asche, Manfred K. Lechner

The Cross City Tunnel comprises 2km of a new underground traffic route in Sydney, Australia. The route is very complex, involving some six separate tunnels and three underground Y-junctions. For almost 200m the six tunnels run parallel at different level sunder William Street, Sydney. Almost all of the route runs adjacent to the City Business District of Sydney and adjacent to or below many major buildings and services. The planning and design of this project is described. The geometric arrangement is achieved with a strong dependence on 3D road design packages. Road alignment constraints include land acquisition and proximity to existing tunnels and basements as well as maintaining separation from the other tunnels in the scheme. Geotechnical and hydrogeological studies are described. Findings discussed include the high horizontal stress field in the Sydney area and investigation of incised palaeochannels on the route. Methods of design for the tunnels and Y-junctions are described, as well as methods of settlement prediction for the buildings and services. The latter includes the settlement assessment for more than 200 buildings, many in excess of 20 storeys, as well as services including all of the city railway lines in Sydney.

Jan 1, 2003

By Frits Agterberg

Statistical exploration uses statistical methods to identify targets for more detailed investigation by estimating the odds of occurrence of mineral deposits. The study area which contains the possible targets may be as large as 1 000 000 km2 or as small as 100 km2. Results are presented in terms of a probability index for the existence of a deposit or, more precisely, in terms of expected dollar value for a unit area, or even in terms of number, size, and grade of deposits remaining to be discovered. Typically, selected geological, geophysical, or geochemical information is systematically quantified and statistically analyzed by using the computer in order to distinguish between geological environments on the basis of the probability that they contain undiscovered deposits of a specific type. All possible targets are compared with one another by using information on areas known to contain deposits. The information on the known areas is either a set of control data consisting of values for the same parameters as are quantified for the entire study area, or it embodies a specific model for the occurrence of a given deposit type. Examples of both procedures will be discussed in this chapter.

Jan 1, 1979

By Peijian Zhang, Yansheng Liu, Yuusaku Tominaga

The directions for ventilation control are often given in linguistic styles such as "if the airflow rate measured is small, a high value of rotation on a local fan should be chosen." In order to control the underground climate using a computer instead of a human being, both the reliability of data values measured underground and the application of human recognition of data values are required. The efficiency of data transmission is dependent on a method of checking a signal which is changed by mixing noises resulting from cases of electrical and mechanical damage to cables. In the study, fuzzy reasoning is adopted to choose a checking method for underground conditions from a normally operating state to an emergency. Fuzzy reasoning is applied to control airflow rate under the linguistic control rules given. It is shown that an effective series of linguistic control rules derived by fuzzy-sets theory is available in ventilation control when used in conjunction with an air velocity sensor, a computer and a local fan with thyristor control. Moreover, a system to make an optimum series of linguistic control rules for ventilation control is introduced.

Jan 1, 1987

By J. F. T. Agapito, L. J. Gilbride, K. Hollberg

Room-and-pillar mining at the Big Island Mine uses narrow, yield (i.e., load transferring) pillars to achieve high resource recovery and productivity. Two flat-lying 3- to 3fi-meter (10- to 11fi-ft) seams are mined. The interburden between the seams is about 10 meters (33 ft) and the cover depth is 250 to 330 meters (820 to 1,080 ft).Most of the mining has been single-seam, but two-seam mining will begin in the near future. Yield pillars minimize stress transfer between the seams. However, it is important that good long-term stability be maintained to prevent subsidence over a large portion of the mine beneath the Green River channel. Three stress issues impacting stability are discussed in this paper: (1) higher-than-gravity vertical pre-mining stresses, (2) time-dependent stress transfer or arching, and (3) stresses induced by strata gas. Although the stress environment and behavior is not fully understood, steps have been taken in mine design and operations to minimize impacts to stability. Stress determinations have been very important to verify analytical predictions used in mine design and in long-term stability assessment.

Jan 1, 2004

By Colonel Oattis E. Parks

The quantity of coal recovered by diamond coring techniques is not sufficient in many instances to make meaningful coking and/or ash fouling tests. Quantities in excess of that obtained by conventional coring techniques, usually in amounts exceeding 500 pounds, has been designated bulk sampling. During the past three years, AMAX Coal Company has utilized five methods of bulk sampling. It was our desire to obtain a bulk sample that was diagnostic of the seam by the most expedient and economical method. From the beginning all of our efforts have been directed to methods which would extract the required coal from slim boreholes which provide quick and inexpensive access to the coal seam, regardless of depth, terrain and accessability. In our efforts and investigation several large diameter cores have been taken from thick coal seams at relatively shallow depths in easily drilled rocks. On the other hand, for deeper thin seams multiple large diameter coring is more expensive and time consuming. It is somewhat less expensive when multiple cores are taken from a single slim borehole utilizing deflection coring, although considerable skill is necessary.

Jan 1, 1973

By Xinzhi (Thomas) Du

"A longwall mining method is a productive mining method of coal extraction that involves the complete removal of large, rectangular panels of coal. Since this method causes deformations through the overlying strata to the ground surface, the surface- and ground-water regime above the longwall panels may be adversely affected and drained into the lower strata. The purpose of this study is to determine the effects of longwall mining subsidence on surface- and ground-water systems.This study is a site-specific hydrogeologic analysis conducted before, during, and after panel retreat at a site located over two selected longwall panels in the Pittsburgh coal seam in Greene County of Pennsylvania. Mine subsidence causes fractures in the overlying strata and enlarges bedding plane separations, increasing the effective porosity and storativity of the overlying strata. Generally, the water in deeper aquifers located in the lower fractured zone drains into the mine void due to the vertical fractures. Moreover, the water level does not recover after longwall mining (but may recover when the mine is flooded). The upper aquifers over the thick aquitard layers may maintain the water level or drop slightly during longwall mining and recover very quickly. The reason is that the underlying aquiclude layer has less change in porosity and permeability after longwall mining (Carver, 1994).A groundwater flow model-MODFLOW was used to predict the water table contours for the periods of pre- and post-mining conditions. The hydraulic gradients of post-subsidence became larger outside the panels and smaller inside the panels than that of the pre-subsidence. The groundwater hydraulic heads above the longwall panel dropped a maximum 50 ft in the study panels. The shallows monitoring wells that were less than 50 ft deep from the surface were deeply affected by longwall mining subsidence. For the intermediate wells that were more than 85 ft deep from the surface, where strata movement acted as a unit during longwall mining subsidence, there were little impacts of longwall mining on the intermediate wells in the study area. For the deep wells that were located below the Waynesburg sandstone, the water was drained to the underlying strata or even into the mine gob."

Jan 1, 2019

By Y. Luo

"Investigating abandoned mine subsidence is often a difficult task because many factors, both mining- and nonmining-related, can affect the possibility and the formation process of surface subsidence events over abandoned underground room-and-pillar mines. Among them, mine water frequently plays an important role in causing such subsidence events. However, mine water could also serve the purpose of preventing subsidence. The dewatering of abandoned room-and-pillar mines has been identified as the main cause for a number of serious mine subsidence events in the past.In this work, the mechanism of mine water to prevent surface subsidence over abandoned room-and-pillar coal mines was studied. Two mathematical models are proposed to quantify the potential effects of mine water on the structural stability of mine pillars, roof and floor as well as the potential for causing surface subsidence. The models are validated with an actual case. IntroductionThe potential for room-and-pillar mining operations to induce surface subsidence is mainly dependent on the recovery ratio in the underground mines that directly relates to the stability of pillars. Normally, if the recovery ratio is less than 50 percent, the mine pillars are sufficient to support the overburden strata without their collapse in a sufficiently large contiguous area. Consequently, there will be no surface subsidence. However, if the recovery ratio is greater than 70 percent, the pillars are too small to support the overburden strata and can cause immediate surface subsidence. In 1993, a mathematical model and program was developed and proposed (Luo and Peng, 1993) to predict surface subsidence caused by high-extraction, roomand- pillar mining. When the recovery ratio is between 50 and 70 percent, the mine pillars could be loaded near their critical condition and, therefore, the surface subsidence is uncertain to develop. If the surface subsidence did not occur immediately, mine water starts to fill the underground openings. If thick, clay-type rock layers are presented in the mine roof, floor or pillars, they can be considerably weakened by mine water and cause surface subsidence. The techniques to investigate subsidence events over inactive room-and-pillar coal mines caused by the weakening effects of raising mine water to the claystone immediate roof and floor were presented in Luo (2009, 2011)."

Jan 6, 2018

By T. R. Ley

"INTRODUCTION Brutally honest mining executives will tell you that “safety is job #1 but.. dollars are also extremely important”. When economic times are tough, as they are now in mining, it can feel like you need to choose between safety and cost control. Leading edge companies know that it is excellence at both that provides the best performance. FLUID POWER SYSTEMS Fluid power systems are ubiquitous in mining – longwall systems, continuous miners, drills, haul trucks and excavators, etc. And fluid power systems are getting more powerful and using higher pressures to move greater volumes and achieve higher productivity. Average operating pressures in mobile equipment has been rising to 450 bar (6,500 psi) over the last decade. With increased system pressure comes ever increasing levels of stored energy. Stored energy that, if released in an uncontrolled fashion, can do tremendous harm to people and things.Fluid power systems are composed of pipe, flexible hoses, pumps, valves and actuators. They are filled with fluid (mineral oil or fire-resistant) to transmit power to where it’s needed for performing work. With time and use fittings can loosen, component performance diminishes and hoses wear and tear. In hostile environments, like coal mining, hydraulic hoses can fail in as little as 2 years according to DGUV (umbrella association of German Accident Insurers), maybe sooner in some particularly challenging environments. FLUID POWER SYSTEM SAFETY While appearing simple and benign on the surface, fluid power systems, particularly such systems on mobile equipment, have many potential hazards. Hazards that most workers aren’t aware of – particularly young, new hires. And those hazards that can quickly turn deadly. During the past couple of years, including at last year’s SME Conference, I talked to a wide variety of mining people about high pressure fluid injection injuries. Some people, often with little or no field experience, never heard of it. But, people with mine operations / maintenance experience were almost always aware of such injuries.Some had even seen it happen right in front of them. But most claimed it didn’t happen all that often. It just wasn’t seen as a problem!"

Jan 1, 2016

By M. L. Harris, J. Organiscak, S. Klima, I. E. Perera

"The Pittsburgh Mining Research Division of the U.S. National Institute for Occupational Safety and Health (NIOSH) conducted underground evaluations in an attempt to quantify respirable rock dust generation when using untreated rock dust and rock dust treated with an anticaking additive. Using personal dust monitors, these evaluations measured respirable rock dust levels arising from a flinger-type application of rock dust on rib and roof surfaces. Rock dust with a majority of the respirable component removed was also applied in NIOSH’s Bruceton Experimental Mine using a bantam duster. The respirable dust measurements obtained downwind from both of these tests are presented and discussed. This testing did not measure miners’ exposure to respirable coal mine dust under acceptable mining practices, but indicates the need for effective continuous administrative controls to be exercised when rock dusting to minimize the measured amount of rock dust in the sampling device IntroductionTwo recent regulations have modified operators’ rock dusting schedules in order to meet compliance standards. First, the 80 percent incombustible requirement in intake entries has increased both on-section and out by the- section rock dusting. Secondly, the recent change to the respirable dust regulation has increased the number of respirable dust samples taken per sampling cycle. Previously, when only five samples were needed bimonthly, rock dusting could be scheduled to not interfere with the respirable dust sampling schedule.The significant number of samples now required under new regulations, combined with the need to maintain 80 percent total incombustible content in active mining areas, require the schedules for respirable dust sampling and rock dusting to overlap. Although rock dust is considered a nuisance dust in relation to U.S. Mine Safety and Health Administration (MSHA) sampling, these overlapping schedules raise concerns about the amount of rock dust that potentially is included in the sample. Additionally, the respirable dust maximum was lowered from 2.0 mg/m3 to 1.5 mg/m3 effective Aug. 1, 2016, increasing concern that rock dust contamination may be an issue (MSHA, 2016). Currently, the acceptable practice is to apply administrative controls such as keeping the miners upwind during rock dust application, or to schedule rock dusting during a maintenance shift when the number of miners present is lower."

Jan 5, 2017

By E. -R. Niinikoski, M. A. Islam, H. Mischo, G. Barakos, J. Joutsenvaara, G. Meissner

European Union's transition to a low-carbon and digital economy highly depends on securing the strategic autonomy of the Critical Raw Materials (CRMs) supply chain. This paper introduces a European Commission-funded research and innovation action, AGEMERA, which aims to create detailed geological and people's concerns maps to unlock the CRMs potential in Europe. Furthermore, the project will develop educational packages for schools and universities, publish online CRM-related games and news flashes, and arrange public events to ensure a basis for socially accepted and sustainable exploration and mining of CRMs in Europe. 1. IntroductionCritical Raw Materials (CRMs), crucial for shifting to a low-carbon and digital economy, should focus on maintaining Europe's overall supply-demand balance (Birol, 2022). Therefore, to proactively address the surge in demand and ensure the strategic autonomy of European industrial supply chains, the exploration and extraction of CRMs must be scaled out across the continent. Moreover, mobilizing Europe's domestic potential is vital for the EU to become more resilient and to establish open strategic autonomy as the demand for CRMs continues to increase quickly on a global scale (European Commission, 2021). Base metal extraction and mining have a long history in Europe. Nevertheless, CRMs mining projects have shown less success, although these have a lot of potential (Guzik et al., 2021). The main barriers are a lack of investment in mining and exploration, complicated and drawn-out national permitting processes, and low levels of public support (European Commission, 2020). It is necessary to have a vast amount of knowledge and intelligence about CRM's potential and market impact. Novel non-invasive geophysical survey techniques that enable sustainable exploration must be created and used to enhance mineral system models of ore deposits incorporating CRMs. The minerals policy framework significantly influences the mining industry's performance, stability, and sustainability. However, the EU Member States' mineral policy frameworks differ significantly (MINLEX, 2017). In addition, the Fraser Institute Annual Survey of Mining Companies offers concrete information on how managers and executives of mining companies view key policy areas that impact mining activities in the jurisdiction in which they operate or are familiar (Jackson & Green, 2015).

Feb 1, 2023

"On-site research and development as well as in-situ testing are key factors to the successful implementation of new mining equipment and technology. Unfortunately the demands and necessities of research and development often conflict with the reality of mine production in operational mines, especially during early stages of research and development and the initial testing of new equipment. Several experimental mines under university supervision attend to this problem and provide a close-to- reality testing environment for the mining industry and mining equipment manufacturers. This paper gives an overview of the design and organization of such an underground testing area as well as of the wide range of possible operations it can facilitate at the example of the FLB Experimental and Teaching Mine (Forschungs- und Lehrbergwerk) at Technische Universität Bergakademie Freiberg, the central European underground research mine. INTRODUCTION As well as the Mining Engineering education follows the same pattern worldwide, the tasks and duties to be fulfilled by engineers in the productive mines are comparable around the globe. This also holds true for the technologies and equipment needed, both in surface and underground mines. Almost all mining equipment brands are being distributed worldwide. The tasks and challenges of guaranteeing an ever- increasing productivity at the mines, while simultaneously maintaining, respectively improving, safety standards, also in the developing countries and emerging economies, requests a constant development, improvement and adaption both of the engineering education and of R&D in technology and equipment. The increasing safety requirements at the mines, in combination with also increasing safety and liability policies, do often not allow a proper practical education of mining engineering students. At the same time, new technologies and equipment to be deployed / brought to the mines have to be fully functional in a production operation from the very first moment. Time losses like break-down time or even repair and maintenance breaks are often costly and, even when expected up to a certain degree with newly developed machines, have a wider negative impact on the neighboring operations and operations within that mine, thus often being unacceptable within the ongoing production process and extremely costly."

Jan 1, 2015

By E. J. Ostrowski

The history of ironmaking dates back to 4000 BC when an open forge was used to produce a sponge iron from a heap of ore and charcoal. Even at this early date, man recognized the need for a fuel and a reducing agent. As time passed, man developed new methods of producing iron; however, these developments were centered on the mechanical aspects, and as a result, a furnace evolved which is now known as a blast furnace. During this period of evolution,' man struggled with the only fuel he knew - charcoal. Some 5600 years passed before any attempt was made to use coal as a fuel for the blast furnace. The use of coal had its beginning in 1619 when Dud Dudley of England first attempted its use in the blast furnace; as a-fuel and as a reducing agent. Coal charged to the top of the blast furnace was not satisfactory. The volatile matter of the coal choked the flues, and also the poor, strength qualities would not support the weight of the ore. Breaking up of the coal compacted the stock column to an impervious mass. One hundred and sixteen. years later in 1735, Abraham Darby of England introduced coke as the fuel and reducing agent in the blast furnace. The acceptance of coke as a fuel for the blast furnace was not spontaneous. As late as 1870, one-half of the pig iron product of the United States was made with anthracite coal, 30 per cent with raw bituminous coal and coke, and 20 per cent with charcoal. However, by 1910, 96.2 per cent of the blast furnace product was made with coke, 2.4 per cent with anthracite and coke admixture, and 1.4 per cent with charcoal. Coke became the standard fuel in the blast furnace. As the art of ironmaking progressed, more pig iron was produced and more coke was consumed. Coke oven capacity was progressively increased. In 1910, there existed approximately 4,000 coke ovens; in 1960 there was approximately 15,000 ovens. This increase in coke oven capacity was necessary to feed the mammoth appetite of modern blast furnaces.

Jan 1, 1962

By Edward (Ted) Dowey

City Water Tunnel No. 3 is being built in order to provide a redundant system for delivering 4,542,500 m3 (1.2 billion gallons) of water per day throughout the five boroughs of New York City. The present tunnels, City Tunnel No. 1 and 2 (Figure 1), were put in service in 1917 and 1936 respectively, and both have been in continuous service. Tunnels No. 1 and 2 can-not be shut down for inspection or repair until City Tunnel No. 3 has been completed. City Tunnel No. 3 has two stages (Figure 1).Stage One is 20.1 km (12.5 mi) long and is presently delivering drinking water to the boroughs of the Bronx and Manhattan. Stage Two consists of the Brooklyn-Queens Tunnel 17.7 km (11 mi) and the Manhattan Tunnel 14 km (9 mi). The Brooklyn-Queens leg is complete and is set to be put in service soon. The Manhattan Tunnel is being constructed and is the subject of this paper. The Manhattan Tunnel (Figure 1) is comprised of three legs: the north, south and east legs. The con-tract includes the excavation of 8,976 m (29,500 ft) of tunnel and the lining of 14,561 m (47,773 ft) of tunnel. The south tunnel, 5,705 m (18,720 ft), was excavated but not lined, under a previous contract. The tunnel ranges from 181 m (600 ft) to 152 m (500 ft) in depth in the bedrock under Manhattan. The tunnel contract also includes the construction of nine new shafts, 161 m (530 ft) average depth, and the completion of a tenth shaft (the previously built construction shaft). The Manhattan Tunnel contract was awarded to the sole bidder Schiavone/Shea/Frontier Kemper Joint Venture (SSF) for $668,532,680.00, on January 31, 2005. The Manhattan Tunnel was designed ?in house? by the New York City Department of Environmental Protection (DEP) and the construction management was provided by a combined staff of the DEP and a joint venture of Jenny Engineering and URS.

Jan 1, 2008

By M. Javier

This concept paper is presented in the hope of raising the awareness of mankind on the necessity for its peaceful coexistence with nature. It is a food for thought. It takes compromise and sacrifice of people, who will have to learn to curb their greed and move toward a more organic form of prosperity. A nature-friendly sustainability is first step toward the protection of nature that is critical to the mutual survival of mankind and nature. People need the resources from the finite earth to survive and nature needs the prevention of human destruction in order to continue to regenerate and provide. The contemporary notion of sustainability is self-serving. It serves the interest of industry by camouflaging itself to look like nature?s protector. The ?sustainability? concept presented in this paper aims to extend the longevity of the utilization of the limited natural resources for many generations to come. It is an important, responsible first step in creating a healthy sustainability concept that, when implemented, extends the longevity of mankind by the most efficient use of the finite resources on this limited Planet Earth, all the while taking into consideration the increase in anthropogenic activities due to exponential human population growth. This new definition of ?sustainability? has completely different characteristics than its contemporary versions. Nature has its own destiny, rules and principles. Being a part of nature, human society depends on it for survival and must play by its rules and never the other way round as in its initial pretensions. Society should not try to humanize nature, but rather to respect the rule of the nature in a peaceful way of co-existence. When implemented, this new concept of sustainability aims to affect the designs of engineered structures and revolutionize the recovery methods and processing of natural resources, such as mineral resources in the most efficient manner. Finally, this paper intends to stimulate critical thinking and initiate serious discussions aiming at producing a general consensus for the best definition for human society to not only enrich, but to extend its existence. Thus, the spirit of this new definition is pro future generations and environment. KEYWORDS: Sustainability Definition, Nature, Geomímic, Deproduction.

Feb 27, 2013