Search Documents

By A. N. Papadopoulos

The life cycle assessment and the performance of pine fence posts treated with water borne preservatives and oils after 18 years exposure in ground contact were examined in this study. Vacuum CCB treated fence posts were subsequently treated at their lowest part (ground contact) with creosote using the open hot and cold tank process and exposed under warm dry temperate climatic conditions in Greece. After 18 years exposure, samples were taken from the above ground contact, top, middle and ground contact and tested for toughness using a Denison single blow impact bending test machine. There was no significant reduction of toughness in any of these zones. Chemical analysis of the residual CCB of unexposed and exposed samples by ICP showed that copper and chromium losses were insignificant while boron losses were significant (more than 50% of the initial content). This was attributed to an effect of creosote treatment.

Jan 1, 2008

By Jack Bradbury

The open stope room and pillar method of mining is used throughout Ozark Lead Company's underground mine located at Sweetwater, Missouri. This method of mining produces an approximate overall ore extraction of 80%. Pillar recovery, on a limited and experimental basis, was started in January of 1979 to determine the maximum size underground opening that could be mined safely. Monitoring the roof and surrounding pillars for potential failure during this pillar recovery process was accomplished by utilizing a simple rod extensometer to measure roof sag. Boreholes 7.5cm in diameter were drilled 3.5m into the roof to spot any separations or cracks that might have propagated between the bedded layers of rock. Underground openings 85m in length by 46m in width have been mined successfully without roof or surrounding pillar failure. Continued measurements to establish long term results will be necessary.

Jan 1, 1981

By D. Marinakis

Gas hydrates (GH) are crystalline compounds consisting of a water molecule lattice, in the cages of which suitably sized molecules, such as methane or other light hydrocarbons, are confined. Although this solid phase looks similar to common ice, it contains substantial amounts of natural gas. The necessary conditions for natural gas hydrate formation exist in some deep-sea marine environments and in permafrost regions. Despite the extensive research, which has been conducted in the fields of exploration and exploitation of natural gas hydrate deposits over the last decades, there is still great uncertainty over the estimated amount of hydrates that these reserves bear. The present work examines some key features of sediments which affect their capacity to host gas hydrates. The hydrate content of a natural hydrate formation is correlated qualitatively with factors such as temperature, effective porosity, mineralogical composition, bio-surfactants, pore pressure and compaction pressure.

Jan 1, 2006

By John A. Shuster, Joseph A. Sopko

Construction of two shafts, as well as associated deep concrete structures, for a major storm sewer project in Milwaukee, Wisconsin required ground water control and temporary ground support to depths ranging from 19.2m to 55.0m. Lowering of the site ground water table eras not possible because of potential consequences for existing nearby structures. Construction entailed completion of two shaft collars into bedrock. In addition to the shafts, several adjacent connected. structures were completed. Ground freezing was selected to provide temporary ground support and ground water control for all excavations. The first application of using reinforced frozen earth was successfully incorporated on the project. The procedure enabled the contractor to create openings in excess of 9.1m in height, without bracing, through highly stressed frozen earth walls. Design features and construction procedures for completion of ground freezing and related excavation are reported.

Jan 1, 1989

By Ronald J. Allain

Water soluble polymers play an important role in many industries. The mining industry is dependent on these materials to help accomplish many solid-liquid (water) separations. Mechanical devices alone are not capable of achieving the degree of separation needed. Mechanical and chemical separations act in concert to accomplish the necessary separation. The history of the use of water soluble polymers has gone through several evolutionary phases and I believe we are facing another of these phases. At first, various natural products were common - starches, gums, and various polysaccharides. These were replaced by the synthetic polymers based on copolymerization of various vinylmonomers mainly in conjunction with acrylamide. The use of these polymers and their needs continues to grow. This paper will cover a brief overview followed by a look at the future of water soluble polymers. A focus will be on applications of water soluble polymers in the mining industry.

Jan 1, 1994

Diesel engines are used in underground mining 1 throughout the world. Exhaust gases from those engines contain toxic components. To protect quality in underground mines, diesel emission control was introduced decades ago, many years before the first surface applications. Today, emission controls, such as catalytic converters, are standard on underground diesel engines in countries concerned with occupational safety and health. Nett Technologies manufactures a range of diesel emission-control devices for underground mining. Emission problems are not the same at each mining operation. And there is no universal control technology. The selection of exhaust aftertreatment technology depends on raw exhaust emissions, particular emission problems, fuel quality and economics. Some of the technologies that have been used in underground mining to control diesel emissions include catalytic converters, diesel filters, fume diluters and water scrubbers. Table 1 compares the effectiveness of these technologies to control the particular components or aspects of diesel emissions.

Jan 1, 1997

By H. Lyn Bourne

The is the 13th year for this column and the 12th in which the royalty data have been tabulated. There still exist some holes in the list of royalties that readers hopefully will fill. The most common mineral commodity is construction aggregates - either sand and gravel or crushed stone. In spite of their pervasive use nationwide, there are states from which the author has no information about royalties for either of these commodities. The reader can help - share information about these missing states and next year there will be fewer states without information. Severn Brown again sends helpful information from the Prospectors and Developers Association of Canada (PDAC). The PDAC Digest contained an article that distinguished between ‘net smelter return royalty' and ‘net profits royalty’ (Haase). The article also lists clauses and details that Brown suggests should be included in a net profits royalty contract.

Jan 1, 1994

By Cherie M. Tilley

The Stillwater Mining Company has acquired a Tunnel Boring Machine to expedite the mine development operations at its Stillwater Mine. The machine purchased by Stillwater was previously owned by Melbourne Metropolitan Board of Works, Melbourne, Australia. The machine was manufactured by Robbins Co. of Kent, Washington. The Stillwater Mine has an extensive system of footwall laterals which are required by the mine development scheme. The initial mine plan called for in excess of 30,500 linear meters (100,000 linear feet) of footwall lateral drifts at a cross section of approximately 3.0 meters in width by 3.75 meters in height (10 feet x 12 feet). A Tunnel Boring Machine was selected for this work. The Robbins machine number is 146-193. This machine is approximately 4 meters (13 feet 5 inches) in diameter. The machine was modified extensively prior to commencing operation at the Stillwater Mine.

Jan 1, 1989

By L. Korkiala-Tanttu, M. Rinne, Z. Song

Disposal of mine tailings has been recognized as an unavoidable burden of mining companies and local authorities. Conventional methods dispose mine tailings in a passive manner which hardly generates any value from them. On the other hand, growing local communities close to mines need more infrastructures which require great amounts of raw materials. In view of the above mentioned situation, a novel utilization of mine tailings is explored as alternative material for asphalt pavement, in order to extract more value from mine tailings and solve the high cost of pavement material. Inherent physical properties of the mine tailings were first investigated to find out their availability as pavement material. Then test specimens were made as mixture of the mine tailings and other pavement material to be tested in laboratory. The mine tailing materials presented a considerable potential as asphalt filler for low-volume roads. Furthermore, the limitat

Jan 1, 2011

By D. P. Patil, T. C. Rao, J. P. Barnwal

Factorial design of column flotation experiments was used to understand the main and interactional effects of the column parameters. In the experiments, the air flog rate, the wash-water, flow rate and the froth depth were varied at two levels. Analysis of the results showed that an increase in airflow rate had a deleterious effect on the grade of the concentrate, whereas, an increase in froth height increased the grade. The interactions between airflow and wash water and between airflow and froth height were significant with respect to grade of the concentrate. These results demonstrated that, from an ore containing 12.76% P2O5, it is possible in a single-stage flotation column to obtain a concentrate containing 31 % P2O5 (10.6% Si02) with a recovery of 94%, thus reducing the number of cleaning stages that would be required if conventional flotation cells were used.

Jan 1, 1997

By L. W. Saperstein, M. C. Radomsky, D. L. Passmore, J. D. Bennett

About 60 small surface coal mines in Pennsylvania participated in a program designed to improve safety performance in the workplace. The method involved the use of safety sampling and observation to assess the degree of safety exhibited by workplace behavior and conditions. Data were collected through the use of on-site safety instruments covering seven major occupational positions typical of small surface mines. Workplace events observed (acts and conditions) were assigned a hazard classification. Feedback was initiated to improve safety performance in areas failing to conform to appropriate safety standards. Results suggest that the variety of unsafe acts and conditions associated with the companies observed are extensive. Further, the experiences drawn from this pilot project have proven the need to pursue this behavioral approach. Future research should concentrate on subjecting the present approach to a strict experimental design involving randomly selected “poor risk” mines.

Jan 1, 1987

By H. J. Handewith, W. D. Coski

This paper describes the development and testing of the RAMEX excavation system. Incorporating a synergy of low velocity, high energy impact and kerf cutting, this machine offers a competitive alternative to drilling and blasting in hard rock. It is a boom mining machine that incorporates the features of a lightweight roadheader and it can mine nearly any shape opening in hard rock. The RAMEX Tunneler has been developed to satisfy industry demands for a non-explosive, flexible, continuous and rapid underground rock excavation system. It will produce minimum ground vibration in the urban environment and allow the flexibility necessary for thin seam mining conditions. It will also reduce initial ground support costs and has a minimum impact on rock integrity. Developed by RAMEX Systems with cooperative research provided by the U.S. Bureau of Mines, this system, could produce the next step in the continuing evolution of mechanical mining systems.

Jan 1, 1989

By Catherine T. Aimone

A computerized cost model has been developed to simulate the technical and economic effects of strip mine blasting in the vicinity of structures. Current surface mining regulations restrict the allowable level of production blasting as a function of this distance. Blast design modifications,' therefore must be employed when blasting in the vicinity of homes to ensure compliance with federal and state regulations specifying limits to the seismic effects generated from a blast. The blasting level allowed. is computed by the charge weight of explosives per delay from the following scaled distance formula: [ ] where W is the charge weight per delay, in kilograms (pounds), D is the distance factor corresponding to the regulatory limit of peak particle velocity to which a structure may be subjected to. Current regulations specify 2.54 cm (1.0 in.) per second corresponding to a SD factor of 27 (60) (Federal Register, 1977).

Jan 1, 1982

By Gary S. Brierley, Ronald E. Romley, Alan L. Howard

The Price Road Drain Tunnel in Tempe, Arizona is part of the drainage system constructed in conjunction with the Outer Loop Highway in metropolitan Phoenix. The Outer Loop Project is a part of a much larger expressway system that includes other large drainage tunnels such as the Papago Freeway Drain Tunnels. Large diameter downhole inspection borings were utilized to obtain subsurface data for the design of these tunnels. Subsurface data obtained from the large diameter borings resulted in the development of empirical parameters that were successfully incorporated into the Geotechnical Design Summary Report and which satisfactorily predicted ground behavior, formed the basis for improved geotechnical design criteria, and facilitated the cost effective assessment of third party risk. The purpose of this paper is to describe the subsurface exploration program performed for this project and to explain the methods used to evaluate underground construction procedures.

Jan 1, 1991

By P. R. Dugan

Sulfur removal from high sulfur coal has several objectives including: a) reduction of the atmospheric load that contributes to the problem of acid precipitation; b) reduction of ash, which contributes to decreased energy transfer in boilers, as well as ash disposal; and c) alleviation of the social and economic dislocations related to uneven geographical distribution of sulfur in coal reserves. Cost in relation to the value of refined coal will govern the development of an emerging coal refining industry. Estimation of the premium paid by power companies for coal with a low sulfur content is a good estimate of the value that will be added as the result of refining. Estimates of premiums paid in 1984 are $28.65/t ($26 per st) for reduction of total sulfur from 370 to 1% S and greater than $28.65/t ($26 per st) for removal below 170 sulfur.

Jan 1, 1988

By S. Veeramasuneni, Qingxia Liu, Susan Dichter

Gypsum (CaSO4-2H2O) is an abundant and naturally occurring mineral. Under elevated temperatures (250 to 300°F) gypsum loses its crystalline water and is converted to hemihydrate (CaSO4 -0.5H2O). The hemihydrate form is also called plaster that is widely used in wall- board, joint compound, and many other industrial applications. At temperatures higher than 450°F (up to 1,200°F), gypsum loses all crystalline water and is converted to anhydrite form (CaSO4). The loss of crystalline water at elevated temperatures is an endothermic reaction. This property makes gypsum an attractive filler and fire retardant in certain thermosetting plastics. The applications of gypsum in plastics, food, pharmaceutical, and paper coatings will be reviewed in this paper. The future of synthetic gypsum, a by product of various industrial processes, will also be discussed.

Jan 1, 2003

By Markku Virtanen, Pertti Koivistoinen

From the perspective of a large mining company the comminution circuit design is worth keeping within the boundaries of the organisation. The correct circuit design begins from the understanding of the role of grinding. Grinding is a link only in the long "comminution chain," starting from solid rock and ending at the concentrating stage. The final target in comminution is to take a part in the maximization of Net Smelter Return, which goal provides the simultaneous considering of capital costs, operating costs and the economic effect of process results. As a general rule there will be a single crushing stage only, ahead of the grinding process. Grinding does not use any metallic grinding media at all, and there will be fine crushing for critical material in the grinding circuit. Grinding has a minimum two stages, besides, at many concentrators middling products and quite often also tailings are reground.

Jan 1, 1997

By Denis Murphy, James Gusek, Carl Mann, Thomas Wilderman

An active underground lead mine produces water having a pH of 8.0 with 0.4 to 0.6 mg/L of Pb and 0.36 mg/L. of Zn. This water is pumped at the rate of 1.200 gpm into a five-cell, bioreactor system covering about 5 acres. The gravity flow system is composed of a settling basin followed by two anaerobic bioreactors arranged in parallel which discharge into a rock filter polishing cell that is followed by a final aeration polishing pond. The primary lead removal mechanism is sulfate reduction/sulfide precipitation. The discharge has met stringent in-stream water quality requirements since its commissioning in 19%. However, there have been startup and operational difficulties. The system was designed to last about 12 years, but estimates suggest a much longer life based on anticipated carbon consumption in the anaerobic cells.

Jan 1, 2000

By Y. Ooishi, Y. Matsumoto, T. Arai, H. Ohta

The multi-circular face shield (MFS) is a new type of tunnelling machine for construction of the special cross section and has been put to practical use in 1988. The MF shield has two circular faces partially overlapped in a single shield machine and can construct the cross section shaped like glasses for the double track railway. And it is possible to equip two or more cicular faces horizontally or vertically, if necessary. During the development of the MF shield the experiments have been carried out for the purpose of estimating the excavatability and the face stability of the MF shield. As a result it was confirmed that the both types of MF shield (one with double faces aligned horizontally and the other with double faces aligned vertically) has higher performance in the face stability and lower value in the cutter torque and the total thrust than the conventional circular shield.

Jan 1, 1991

By W. J. Stone

In response to concerns over the impact of mining on the hydrologic balance at the Navajo Mine in northwestern New Mexico, a recharge study was conducted using a chloride mass- balance approach. Impact of mining on annual recharge volume was assessed by comparing pre- and post-mining recharge values. The mean regional recharge rate for reclaimed ground (weighted by acreage) is 1.02 mm/a (0.04 in. per year) or twice that for undisturbed ground, 05 mm/a (0.02 in. per year). Comparison of regional recharge volumes for identical areas shows mining increases recharge 92%. The increase is only 80% if no closed depressions are constructed during reclamation. However, the increased rates are so low that there should be no detrimental impact on regional water resources. The chloride method proved useful at Navajo Mine and should succeed at others surface coal mines as well.

Jan 1, 1991