Search Documents

By Tyler A. Dawson, Ryan P. Butler, Timothy Gualandri, Jason R. Edberg

"In the early 1920’s, the City of Tulsa, Oklahoma constructed an approximately 8,238-foot long tunnel, the Tiawah Tunnel, through bedrock. Voids behind the concrete tunnel liner were detected via probe drilling in early 2000 as part of an interior visual condition assessment. In 2012 and 2015, conditions along the entire tunnel were efficiently assessed through geophysical investigation using ground penetrating radar (GPR) along the inner tunnel crown and at various select locations within the tunnel. Fifty-seven (57) potential voids, extending up to 19 inches in depth and 12 feet in width, were detected with 1,000 MHz GPR and confirmed through probe drilling with approximately 80% accuracy. GPR proved to be an efficient and reliable technology for void detection behind concrete tunnel lining. This paper highlights the geophysical investigation and how geophysical efforts were combined with other investigation efforts to definitively determine the presence of voids outside of the tunnel lining.INTRODUCTION The city of Tulsa, Oklahoma has a population of about 400,000 people. The original source of water for the city was the Arkansas River. The first pumping operation provided untreated water to homes and businesses in 1904. The residents of Tulsa found this water to be unacceptable due to the high levels of salt and gypsum present. As the city grew, land and storage/treatment facilities were acquired in order to obtain and distribute a more suitable raw water. The raw water needs for the city are currently satisfied by transport and treatment of about 100 million gallons per day (MGD) of water from surface water sources. Water is transported many miles from Spavinaw/Eucha and Oologah lakes to Yahola Lake and the Lynn Lane Reservoir (totaling over 3-billion gallon capacity). From here, the raw water is treated and transported to the various customers (City of Tulsa 2015). The Tulsa Metropolitan Utility Authority (TMUA) is responsible for the operation and maintenance of the raw water transport system."

Jan 1, 2016

By Allen Latham

It started' in 1936 when some Dutch adventurers wanted to scale the highest mountain in the South Pacific. Quite by accident, they discovered the Ertsberg, a contact deposit of magnetite laced with chalcopyrite, in a high mountain valley where it had been gouged at by glaciers and finally left as a solitary pillar for its discovery by a geologist who lent purpose to the expedition, Dr. J.J. Dozy. By the-.time a report was published describing the deposit, war had hit the Netherlands. Perhaps again by accident, the report was uncovered in 1959 by the East Borneo Company. At this point, Freeport entered the scene through its vice president for exploration, Forbes Wilson. During the course of a meeting on laterite prospects, the Ertsberg was introduced and he put the wheels into motion for Freeport to join in its exploration. You might, at this point, ask yourself whether you or your company would have taken on a venture to look at a reportedly large high grade copper outcrop in New Guinea, an unexplored land known best for its inhospitable climate, terrain and head-hunters. I heard the chief executive of one large mining company comment sometime back that neither he nor his company would have gotten involved. I won't attempt to describe the trials of the initial exploration expedition that passed through dense-man grove swamps, tropical jungle and across jagged mountains a distance of some 200 miles to get to the Ertsberg in 1960. It should be chronicled by its participants - Forbes Wilson, Del Flint, and John Bowenkamp. Needless to say, the participants relish the experience but wouldn't be among those volunteering for a return engagement. As a result, the Ertsberg changed from a reported outcrop to a mineral deposit containing an estimated 13 million tons with systematic surface sampling indicating a copper grade of over four percent. Moreover, the deposit extended to an indeterminate depth with the possibility of doubling or tripling. reserves well within reason.

Jan 1, 1971

By D. Tao

Coal is a major source of energy in the U.S. and more than 51% of the electricity used in the country is generated from coal. Coal cleaning prior to combustion is necessary and often accomplished using wet physical processes at coal preparation plants to remove impurities such as ash, sulfur, mercury. However, the resultant clean coal product still contains a significant amount of impurity due to the fact that impurities are not well liberated from coal particles ranging from several millimeters to inches in size at which wet cleaning processes take place. A cleaner coal product can be obtained if a cost-effective dry process is developed to further clean pulverized and thus better liberated fine coal at the power plants prior to its combustion. The benefit of such a process is a significant reduction in the cost of expensive post-combustion chemical cleaning processes such as flue gas scrubbing employed to meet the stringent environmental air quality regulations. In this study, a novel rotary triboelectrostatic separator (RTS) was investigated for its application to dry cleaning of fine coal samples acquired from the power plants in the state of Illinois. The pulverized fine coal contains well liberated ash and pyrite minerals and is an ideal feed to the triboelectrostatic separator for further cleaning without the use of water or any chemical reagents. The proprietary rotary triboelectrostatic separator (RTS) is characterized by an innovative high efficiency rotary charger, charger electrification, laminar air flow, and specially designed electrodes. Compared to existing triboelectrostatic separators, the rotary triboelectrostatic separator offers significant advantages in particle charging efficiency, solids throughput, separation efficiency, applicable particle size range, etc. Testing with several fine coal samples has demonstrated that this technology can significantly reduce ash content with a process efficiency similar to or better than froth flotation. Important process parameters such as charger rotation speed, injection and co-flow rate, feed rate were investigated for their effects on separation performance.

Jan 1, 2010

By Wayne P. Myers

Electricity, as normally thought of by a layman's definition, is a man- made force that has no color, no odor, is not visible, cannot be heard, yet man can control it and make it perform his work for him. A person dare not cheat on it, for it then will master him. It has laws, rules, and regulations that must be strictly adhered to if it is to perform in the safest, most reliable, and economical manner. In the early days of coal mining the power source was man himself. Later man employed steam and compressed air to reduce his muscle power requirements needed in the extraction of coal. By the turn of the 20th century, electricity had become the most common source of power for the coal industry. Steam and compressed air are still found in use in isolated cases today for specific applications; however, they are rapidly being replaced by electricity. Electrical laws and regulations are quite extensive and somewhat complex for the proper generation and use of electricity. Man-made laws, rules, and regulations for the care and handling of electricity, designed for man's safety, are rigidly enforced by Mine Safety and Health Ad- ministration (MSHA), as well as the various state departments of mines.

Jan 1, 1981

By Steve Trussell, William H. Langer

"Arizona aggregate (sand, gravel and crushed stone) producers enjoyed more than a half a century of nearly constant growth in demand for aggregates. Approximately 80 percent of the aggregate produced in Arizona is sand and gravel, and 20 percent is crushed stone (U.S. Geological Survey, 2015). Figure 1 shows the generalized distribution of potential sources of sand and gravel (yellow) and potential sources of crushed stone (other colors described below). Black dots show locations of aggregate operations.Sand and gravel commonly is produced from modern river channels and terraces although some alluvial fans and high-level paleo-river terraces also serve as aggregate resources. The gravel clasts are a mix of rock types that reflect the types of rock in the source area of the rivers. Generally processed river gravels meet stringent specifications for highend uses.Crushed stone, which makes up about 20 percent of production, primarily comes from a variety of metamorphic rocks and light-colored intrusive igneous rocks such as granite (brown areas), dark colored extrusive igneous rocks such as basalt and scoria (rust colored areas), and carbonate rocks such as limestone or dolostone (green areas). Carbonate rocks are also used in the manufacture of cement and lime.Construction and aggregate production in ArizonaBecause aggregate producers have limited facilities for storing product, stockpile changes are insignificant compared to production. Therefore, demand or consumption of aggregate in Arizona is considered to be equal to production. Production figures used in this paper reflect shipments, sales or marketable production, including aggregate used by producers to make readymix concrete and asphalt. Production figures were reported by the U.S. Bureau of Mines from 1950 until 1995 and by the U.S. Geological Survey (USGS) since then. Production figures are reported voluntarily, and major operators are the primary source for these figures. Because many smaller operators do not report their production, the figures are conservative values that provide an approximation of aggregates production activity."

Jan 1, 2015

By J. Stephen Slottee, Jerold Johnson

The use of a thickener, without filtration, to produce a non-settling paste (also called thickened tailings) with non-Newtonian rheology has been practiced in Australia for many years for the disposal of red mud. The application of paste thickening technology outside of alumina is relatively new. Interest and installations in paste thickening are rapidly growing. Water shortages and environmental pressures make consideration of thickening tailings to solids concentrations within the paste range necessary in most new tailings projects. The paste thickeners at the DeBeers CTP plant in Kimberley, South Africa are the latest example of paste tailings disposal on the surface, also called “stacking”. Houman (2003) The use of a paste thickener as an alternative to filtration for mine paste backfill is a more recently developed application. This paper describes the principles of design and general operating characteristics of a paste thickener compared to the conventional and high-rate thickener. The application and operating performance of paste thickeners in mine backfill is discussed as an example. An integrated approach to process design is described that matches the performance of the thickener, pumping system, and application on a common rheological basis to ensure that none of these steps prevents achieving process performance targets.

Jan 1, 2005

By Alan Weakly

The Powder River Basin (PRB) of northeastern Wyoming and south-central Montana is the largest strippable reserve of compliant coal (0.6 or less lb of sulfur per million Btu) in the United States. In mining parlance, it is the Mother Lode! Wyoming’s portion of the Basin provides one fifth of the coal produced in the United States annually, and the state has been the nation’s top coal producer for the past six years. Based on 1993 production statistics and estimated strippable compliance coal reserves, Wyoming may remain the nation’s top producer for the next 76 plus years. Past articles on the PRB have focused mainly on production. After living and working in the Basin for the past five years, I have developed an appreciation for the area and its major industry that transcends size and production data. In the fall of 1993, MINING ENGINEERING’s publisher and I decided to present a series of articles that would cover many other aspects of the Basin. Ten topics were outlined, and specific individuals, selected for their knowledge and experience, were asked to contribute articles about their specialties. Although Montana has four large mines producing coal from the PRB, this series of articles will concentrate on the Wyoming portion of the Basin.

Jan 1, 1994

By G. B. Amicucci

Golden Sunlight Mines Inc. operates an open-pit gold mine and cyanidation plant about 11km (7 miles) northeast of Whitehall, MT. Golden Sunlight is a subsidiary of Placer Dome US Inc. Mining is accomplished with conventional open pit drilling, blasting and hauling methods. The mining rate is about 102 kt/d (113,000 stpd). Gold occurs as fine-grained disseminations in a pipe-shaped breccia and in immediately adjacent country rock. The ore body is low grade, averaging 2 g/t (0.059 oz per st) of gold. The metallurgical plant uses conventional carbon-in-pulp (CIP) technology. Daily throughput averages 6.5 kt (7000 st). Recoveries are enhanced through a sand tailing retreatment facility while a preaeration process reduces operating costs. The low grade ore dictates that maximum mill throughput at the desired grind size be maintained. Therefore, in October 1988, an Armco Autometrics (now Denver Autometrics) particle size monitor (PSM) 400 was commissioned. The PSM 400 is an on-line instrument. It measures particle size and percent solids in a slurry stream. The PSM pulls its own sample, deareates the sample and passes it through diametrically opposed ultrasonic sensors. The unit uses ultrasonic sound to measure the deareated slurry stream's particle size and percent solids.

Jan 1, 1991

By Frank J. Klima

Explosives are probably the most widely used and most mysterious large scale' mining tools of modern times. The post black powder explosives were primarily nitroglycerin-based straight dynamites, ammonia dynamites, blasting gelatin, gelatin dynamites, ammonia gelatin dynamites, etc. Of these, the strongest and highest velocity explosive used in industrial operations is blasting gelatin, which is nitroglycerin colloided with a nitrocellulose of medium nitrogen content in proportions which give the product a plastic character, or about 93 to 7. Many variations of the basic groups above were developed by substituting ammonium nitrate and/or sodium nitrate for some of the nitroglycerin. The nitrates being insensitive to caps required a certain percentage of nitroglycerin to sustain detonation in smaller quantities or diameters. Paralleling the development of industrial dynamites was the development of more expensive, highly sophisticated explosives which were developed for specific military purposes. Such explosives as Amatol, RDX, Composition A, Composition B, Composition C, Lead Azide, PETN (Pentaerythritol Tetranitrate), Tetryl, Pentolite, TNT, etc., were primarily military explosives. Amatol, which is a cast mixture of ammonium nitrate and TNT (Trinitrotoluene), and identified by percentage of AN versus TNT as 50-50 Amatol, 80-20 Amatol, etc., was a favorite World War I explosive. RDX, or Cyclonite, was widely used in World War II. Also used during WW II were compositions A. B, and C, which were mixtures of RDX (Cyclotrimethylene trinitramine), TNT, and other nitrotoluenes. These high explosives, along with nitroglycerine, are exact chemical compositions or mixtures of exact chemical compositions which are individually explosive, or in other words, individually capable of explosive chemical decomposition when properly initiated. These chemical decompositions result in the formation of simpler compounds and/or large quantities of common combustion gases, and large amounts of energy in the form of heat. Of these, the most powerful is RDX which, based on the ballistic mortor test, is 1.5 times as powerful as TNT. Chemically, the decomposition of TNT releases about as much energy as the reaction of ammonium nitrate and fuel oil.

Jan 1, 1967

By Giin-Fa Fuh, Sally A. Shoop

An instrumentation program was developed based on the results of an analytical study of the geomechanical effects of longer longwall face lengths. Boundary element simulations showed that longer face lengths can cause in- creased face convergence and an increase in the shear stresses in the immediate roof. Empirical design methods predict that longer faces will cause little effect on abutment stresses as long as the roof caving is well behaved. On this basis, a longwall face instrumentation program was designed with emphasis on the interaction between face support and ground response for optimizing face conditions. At a 600-foot (183 m) face, five midface shields and two headgate shields were monitored with vary- ing hydraulic pump pressure. The instrumentation included six convergence rods with linear potentiometers to measure canopy-to-toe convergence; fourteen pressure transducers to monitor leg pressures; and two portable data loggers. Similar instrumentation will be in- stalled on a 750-foot (229 m) face for comparison. The results from the 600-foot (183 m) face indicate that a ground reaction curve, as determined from the relationship between the sup- port set pressure and the roof convergence, can be used to optimize the support pressure to control convergence, the key element to ground stability in the face area.

Jan 1, 1986

By Ernst Langer

INTRODUCTION Morro do Niquel is located near the small town of Pratdáolis in the southwest part of the State of Minas Gerais, Brazil, about 300 km in a straight line north of São Paulo and 300 krn west of Belo Horizonte. The deposit is known since 1935. Systematic exploration started, however, only in 1957 and production with one furnace in 1962. Since 1969, after the installation of a second furnace, the mine produces about 2 500 tons of nickel, contained in ferronickel, per year. This production is now consumed totally by the Brazilian steel industry. The "Morro do Niquel" is a serpentinite stock of 900 by 400 m which rises 200 m high above the surrounding metamorphic rocks of Algokian age (see Figure 1). On top of the hill there is a leached barren zone of about 200 by 400 m, generally 20-30 m deep, which consists practically only of a boxwork of quartz colored brown by limonite. Surrounding this zone on the sides of the hill is weathered, decomposed serpentinite which contains about 213 of the economic nickel mineralization. Roughly 113 of the ore reserves lie below the leached overburden representing ore of a different type. The geological map and cross-section, Figure 2, give a clear picture of the occurrence.

Jan 1, 1979

By John R. Keith

Keith, John R. 1968. Relationships of lead and zinc contents of trees and soils, Upper Mississippi Valley District. Preprint, Fall 1968 Meeting, Soc. Mining Engineers of AIME. Lead and zinc contents of elm, maple, and oak trees and of soils in which the trees grew were determined in samples from the Upper Mississippi Valley mining district, and from an area outside but contiguous to the district. The lead and zinc analyses of plant materials served to differentiate the mineralized and non-mineralized areas. Stems contained about two times as much lead and about 2-5 times as much zinc as did leaves taken from the same stems. Lead and zinc analyses of all soil horizons could be used to differentiate between the two areas. Soils at most sample sites in the mineralized district seemed to be more reliable than plants for geochemical prospecting and are a more practical sampling medium. Soil samples from areas with thick loess cover, however, failed to indicate the presence of mineralized bodies whereas tree samples from the same sites contained anomalous amounts of lead and zinc. It is suggested that in areas of thick loess cover plant samples could be used in prospecting for lead and zinc.

Jan 1, 1968

By Edmund J. Flynn

My subject Is Industrial Relations. Thus, I may appear as an intruder at this annual meeting of the Society of Mining Engineers. But I am no more an intruder here than is Industrial Relations in the day-to-day functioning of an engineer either in a staff or a line job. Engineers deal with people, as well as with blueprints, organizational charts, production data, etc. Where you have people, you have emotions, gripes, wants - real or imagined. Or you may just need some people or, at the other end of the pole, you may want to free yourself of people. But whether it is the wants or the needs, the pleasant or the unpleasant aspects of dealing with people, an Industrial Relations Department within an organization is there to help with these human relationships. This is the point for a definition of terns. Reference has just been made to "dealing with people? and to "human relations." This is, precisely the area in which Industrial Relations operates in the western Mining Divisions of Kennecott. In other organizations, what we refer to as Industrial Relations, may be called personnel relations, personnel administration, employee relations, or labor management relations. In our opinion the term Industrial Relations is best descriptive of the activity because it embraces the broad field of human behavior, reactions and satisfactions growing out of an individual?s entire employment relationship including his hiring, his lifetime on the job, and his termination. This is an individual?s industrial life. However, despite the use of the word "industrial", we are ever conscious that Industrial Relations is limited to human relations. Operational activities and decisions relating to the mining, milling, smelting and refining processes are for the line organization. The Industrial Relations interest in these line organizations activities and decisions relates only to the impact they nay have on employees - on people generally within the organization.

Jan 1, 1959

By John Reilly

Traditional methods of project procurement of have remained virtually unchanged in the U.S. infrastructure construction industry for more than 50 years. The traditional method, Design-Bid-Build (DBB), uses a two-step process that separates planning and design from construction. Design is generally done by the public agency and their consultants and the subsequent construction contract is procured from the private sector, almost always by a “low-bid” approach. This method has worked well for many projects, delivering quality work for the lowest bid price. This is particularly true for those projects where the work, and the public agency’s management procedures, are well understood by the contracting community and there is relatively low uncertainty in the work or conditions, particularly geotechnical conditions for underground construction. However, concerns exist with the DBB process. It is time consuming because all planning and design work must be completed prior to beginning any construction work and it is of concern for complex or large projects, plus those with significant risk, where the separation of design and construction, in conjunction with pressures resulting from the low-bid environment, often result in substantial cost and schedule increases. Frequently, these increases occur in a non-productive, inefficient, adversarial work environment leading to claims, disputes and costly litigation (Quick 2002).

Jan 1, 2007

By W. J. C. Meynink

In drier regions of the world, total containment of cyanide liquors for rainfalls less than a specific design value is often required by government regulation. For example, in Queensland total containment is required for rainfalls up to 'the 1% annual exceedence probability. In equatorial regions, where rainfall greatly exceeds evaporation, a total containment requirement is unrealistic and this is recognized by regulatory authorities. Regulatory constraints typically require that cyanide concentrations at an agreed downstream compliance point not exceed a specific value more than a specified fraction of the time. While the excessive rainfall prevents total containment, it does provide substantial dilution. This paper outlines a methodology for assessing the distribution of cyanide concentrations at a downstream compliance point in an equatorial region with limited hydrometeorological data. Consider the hypothetical mine environs depicted in Figure 1. The mine is located near the catchment divide and draws its water supply via a gravity line. Tailings from the process plant are piped to a tailings dam on a sub-catchment below the plant site. The objective is to determine the distributions of cyanide species concentrations at a compliance point just upstream of a major settlement to ensure they do not exceed regulatory limits.

Jan 1, 1991

By Somia Gurunathan, Harry Castrantas

Hydrogen peroxide and calcium peroxide are used to improve the extraction of gold/silver and reduce cyanide consumption in heap leaching and mill leaching operations. FMC's standard grade H2O2 and FMC's Permeox™ solid peroxygen, a formulated product containing cao2, was used for the experimental work. It was found that the rates of release and the longevity of these peroxygens in ore-cyanide mixtures are significantly different. When choosing a peroxygen, one of the key factors is extrac­tion time, with the longer extraction times of heap leaching primarily favoring calcium peroxide and the shorter extraction times of mill leaching primarily favoring hydrogen peroxide. A series of laboratory leach tests showed the choice between H2O2 and CaO2 to be ore and process specific. H2O2 and/or Permeox™ improved the gold extraction in four out of five ores tested. (2 sulfide and 2 oxide). Mixtures of H2o2 and Permeox™ were also found to significantly increase the gold extraction rate. A fifth ore (sulfide) did not respond to peroxygen treatment. In addition, savings in NaCN consumption was obtained with Permeox™. Both peroxygens offer economic incentives to gold processing.

Jan 1, 1992

By R. S. Mateer

Linear programming on desktop computers is commonly used to optimize coal blending proportions. The objective function is usually the cost of the blend. The constraints consist of materials and heat balances as expressed as linear functions of the blend. This is illustrated in Example 1. Inclusion of a sulfur compliance constraint in more complex because the maximum permitted sulfur percentage is not a pre-specified constant. Rather, it is a function of the calorific power of the blend itself. The current limit of 1.2 pounds of sulfur dioxide per million Btu may be expressed as: [Sulfur Max%= 0.6 . Hl10,OOO with H in Btu/lb.] A proper constraint equation may be formed by defining for each coal a function that is the difference between the actual sulfur percentage and the maximum sulfur percentage. This may be regarded us an excess sulfur percentage. For Coal A of Example 1. this would be: [ Sulfur Excess%=0.5-0.6 13,000/10,000=-0.28] This value would be used as the coefficient of the weight proportions of this coal in the blend. The complete constraint equation would then be the sum of such terms for each coal set less than or equal to zero. This is illustrated in Example II. [ ]

Jan 1, 1995

By A. Goulsbra, S. McAllister, R. Dunne

Since 1992, a tailings gravity re-treatment plant has been in operation at the New Celebration Gold Mine to recover aurifer­ous pyrite (Martins, Dunne and Gelfi 1991; Martins, Dunne and Delahey 1993). The gravity pyrite concentrate is ground in a Tower mill to liberate gold (average particle size around 25µm) prior to cyanide leaching. Although the re-treatment plant has met the predicted gold recovery, based on original laborat01y testwork, there is still room for improved gold recovery. This requires enhanced pyrite recovery, especially in the finer size ranges. The application of centrifugal gravity separators would seem to be an ideal means to achieve this criterion. In particular, the Falcon continuous centrifugal separator (Series C machines) would appear to be ideal for this particular duty. A testwork program to evaluate the application of the contin­uous Falcon to recover pyrite from New Celebration ores was unde1iaken over a six month period during the later part of 1997. The work involved laboratory batch testwork, followed by con­tinuous testing of the Falcon Cl0 (2tph to 3tph) and Falcon C40 (l00tph) units. A summary of the results from this evaluation program are provided in this paper.

Jan 1, 1998

By Stephen LaBrooy, David Muir

Gold ores in the geologically more recent rocks are often associated with copper minerals which pose problems of high reagent consumption with conventional cyanidation practice. Many examples exist in northern Australia, Indonesia, Papua­New Guinea, Chile, and Brazil where, despite various treatment options (LaBrooy, 1992), the processing of oxide and transition ores is uneconomic either for copper or gold recovery. Hence, there is a need for a reagent which is selective for gold without leaching copper minerals. The ammonia-cyanide system appears to meet this criterion (Muir et al, 1989; LaBrooy et al, 1991; Costello et al, 1992; Hayes and Corrans, 1992) but it has proven difficult to optimise and apply to a variety of ores due to differences in the mineralogy and reactivity of ores and a lack of understanding of how the system works. Recent work on the mechanism, however, (Muir et al, 1993) has thrown a new light on the problem which should allow better process control. Ammonia­cyanide mixtures behave neither like free cyanide nor free ammonia and too much of either reagent in the mixture is detrimental. The key to the process is understanding how ammonia enhances gold extraction yet inhibits copper extraction in an essentially cyanide environment.

Jan 1, 1993

By Robert Jedrzejczak

The Endako Mine is an open-pit molybdenum mine located in the north central region of British Columbia, Canada, about 960 km (600 road miles) north of Vancouver. Production for the latter part of 1992 was expected to averaged 63.5 kt/d (70,000 stpd). Of that amount, 27 kt/d (30,000 stpd) was the mill feed. This production is achieved with five 11.5 to 14.5 m3 (15 to 19 cu yd) electric shovels, six Euclid R190 and two Unit Rig M120 diesel-electric haul trucks, and three 320 mm (12.25 in.) electric rotary drills. There are three ore zones delineated into pit areas: the Endako, Denak East and Denak West. Present mill feed source is the southeast stage of the Endako Pit. Stripping is carried out in the south wall stage also of the Endako Pit. The mine high grade aggregate is reduced in the primary and secondary crushing circuits before processing in conventional RM-BM-flotation circuits. The majority of the molybdenum sulfide (MoS2) is roasted on site to produce technical grade molybdenum oxide (M003). A portion is further refined and treated to yield a 99.9% pure MoS2 product.

Jan 1, 1993