Search Documents

By R. C. Bunge

Many minerals float best with fatty acids in the intermediate pH range. For example, fluorite, a semi soluble salt mineral, exhibits a maximum contact angle and a maximum flotation recovery in the pH range of 6-8 after conditioning in a palmitate solution (fig. 1). The maximum in flotation coincides roughly, as many researchers have observed, with the boundary of bulk precipitation of the fatty acid. According to fig. Z this boundary is in the above case of 5xl0-7 M palmitate approximately at pH 6.3. For assessing the phenomena occurring at the bulk precipitation boundary of fatty acids, the surface tensions of carboxylate solutions have been measured under various conditions. Fig. 3 shows the surface tension development of palmitate and myristate solutions of increasing concentration at pH 12. Also shown are the bulk precipitation edges (BPE) of the respective solid species that is stable under these conditions, that is the potassium acid soap, HKAZ. Both curves display a similar behavior. As the concentration of carboxylat,e increases, the surface tension decreases, until a minimum is reached at which the curves level off. The decrease of surface tension with increasing carboxylate concentration is generally taken to indicate the surface excess of the carboxylate ion. The point where the curve suddenly levels off has not yet been explained. While it is well known that the onset of micellization (CMC) may cause such an inflexion of the surface tension curve, this cannot be the case here because the position of this point depends, as shown in fig. 4 for palmitate, on pH (the CMC is generally independent of pH). We believe that this point indicates the precipitation of a colloidal acid soap (colloidal precipitation edge, CPE) before the bulk precipitation of this species sets in (BPE).

Jan 1, 1994

By James E. McNulty

The planning and development of new coal mines is requiring the increased use of geologic, geologic engineering and hydrogeologic investigations. This is caused in part by the fact that new mines must deal with less favorable conditions than existing mines as well as higher costs of development and in part by the dictates of regulatory authority. High costs of new mines require greater reliability of geologic assessment using best available geotechnical and geophysical methods and technology. Although the increased cost of additional subsurface data is significant, the more important factor may be the impact on project lead time.

Jan 1, 1981

By Wm. I. Weisman

Sometimes in assessing where we are and where we are going it is informative to take a look at where we have been. Whether or not it adds to our understanding of the present, I think it may be interesting to review some of the past history of our industry. As a starting point I chose to use the famous Paley Commission Report, formally known as "The U. S. President's materials Policy Commission -Resources for Freedom."(l) The Paley Commission report said "Fluorspar is an essential raw material for the steel, aluminum, and chemical industries." Of course this statement is still true. It also said, "United States known reserves of fluorspar would be sufficient for some 15 years at present rates of consumption--about 426 000 short tons in 1960. Projected consumption for 1975, however, is several times as great, and reserves in other free countries do not appear adequate to supply United States deficiencies during the next 25 years." This simply demonstrates how even the most learned and competent people can observe all the facts avail-able to them at a given time and yet be unable to predict the future very accurately. We all know that reserves in other countries are more than adequate to supply the United States today, 25 years since the report was published. In fact, the report estimated free-world reserves at something over 36 million tonnes (40 million short tons). Contrast this with 246 million tonnes (271 million short tons) estimated as total world reserves from the section on fluorspar from Commodity Data Summaries of 1974, published by the Department of the Interior. (2) The Paley Report discusses other matters pertaining to fluorspar that are still of interest, such as improving mining methods. Furthermore, it certainly did a good forecasting job in noting that greater recycling should become possible in the aluminum industry in regard to fluorine lost in wastes and also concerning the substitution of fluorspar in the steel industry by other fluxing materials. It also suggested that non-fluorine containing propellants should be investigated as a replacement of those containing fluorine as a conservation matter. Some discussion was devoted to recovering the fluorine content of phosphate rock, which is being practiced today, but was in its infancy in 1950.

Jan 1, 1978

By A. Delgado-Jimenez, O. J. Restrepo-Baena

"Sustainability is a concept that involves several aspects like social, economy and environment. For the concept of sustainable mining is an action that involves to do more in social acceptance, distribution of welfare, an stable economy and the environment. Understanding the mining operation that creates a new state that is necessary to prepare and conduct searching for the best results in sustainability. The results of sustainable mining could be directed to achieve less net environmental impacts, more economic development through the transformation of the natural capital and the social acceptance as the result of good negotiations with the communities in the surroundings. To do that, one option is to create frameworks to planning the regional mining developments that allows the stakeholders to decide and develop different strategies to addresses the sustainability in a mining environment. Strategies based on the understanding of the whole mining business, the environment in which it operates, composed for a natural resources network that interact in a complex system, social system composed by different groups, communities and economies that could be subject to big transformations. INTRODUCTION The mining sector represents one of the most significant challenges for sustainable development, given the magnitude of the impacts that it has on the social and natural systems and the potential to generate welfare associated with its exploitation. Some of the main challenges of mining to contribute to sustainable development are the reduction of the environmental and social impacts of mining operations, to advance in the distribution of benefits in the community and the investing in the development of substitutes. To help in this direction it is necessary to integrate more actors than those who have been considered traditionally in the development of the mining business, and consider the natural environment, communities and the several dynamics generated by the interaction of these elements that contribute to sustainable development. This work provides some useful considerations for sustainable development of mining operations in regions with mining vocation, through the convergence of objectives and the finding of synergies between the existing conditions in the territories and the potential conditions that are generated by new mining developments. A DEFINITION FOR SUSTAINABILITY IN MINING The definition of the Brundtland Commission in 1987 established that sustainable development is ""the ability to ensure that it meets the needs of the present generations without compromising the ability of future generations to meet their own needs""."

Jan 1, 2015

By George Alan Weed

The management of safety is not only the most noble, but also the most personally and financially rewarding of all the management functions. The management of safety should result in the prevention of accidents and the elimination of human suffering and loss of life. Safety management must be the number one priority of all management's production and profit objectives. For years, safety management has been a result of mockery, charlatanism and snake oil presentations dedicated to giving a quick dog and pony show. The result has been an unacceptable record of accidents and fatalities.

Jan 1, 1981

By H. G. Fleshman

?Wyoming bentonite? has become almost a world-wide trade mark for high quality sodium bentonite. Although bentonite is produced in more than a dozen U.S. states the largest producing area covers Wyoming and adjacent parts of Montana and South Dakota. Bentonite was originally known as Taylorite and later renamed Bentonite by Dr. Sam Knight, the State Geologist of Wyoming. The new name came from the Fort Benton shale member of the Mowry Formation. Bentonite is a clay consisting essentially of the montmorillonite group of minerals. Since bentonite has good ion exchange capabilities, various cat-ions are easily replaced. These cations are usually calcium and sodium; however, magnesium, lithium, potassium, and others can be exchanged. One way of classifying the clay is based on its swelling capacities when wet or added to water. Bentonite having sodium as the dominant exchangeable ion typically has very high swelling capacities and forms gel-like masses when added to water. Bentonite in which exchangeable calcium is more abundant than other ions has much lower swelling properties than sodium varieties.

Jan 1, 1987

By Edward J. Adams

In recent years, there has been a shortage of individuals trained in the technical skills entering the mining industry. The university and industry, both indicating their concern, have joined efforts in an attempt to do something about this situation. An example of such an effort is the Pennsylvania State University's Student-Trainee Program in Mining Engineering, now in Its third year. The program is a five-year plan in which six months of schooling and six months of on-the-job training are alternated, climaxed by the student trainee earning a Bachelor of Science Degree in Mining Engineering plus two years of practical experience. The student trainee accepts the work-study plan as a satisfactory method of receiving a thorough education and preparing fog a career in the mining industry. Inasmuch as the work and study-periods are alternated, the trainee has an opportunity' to integrate his practical experience with his academic knowledge. He receives a chance to observe others perform she duties of the profession he is preparing to pursue, and he regards this as an essential part of any such cooperative effort. Even though there are some disadvantages, the trainee feels that the advantages of the program are definitely more decisive.

Jan 1, 1963

By Grant R. Brown

The purpose of this opening paper is to provide an overview of incentives strategies. This overview includes a discussion of the different types of incentives, their advantages and disadvantages and their potential application to the mining setting. Objective The primary objectives of incentive plans are to increase worker (including management) effectiveness and reduce unit labor costs. These plans can be grouped into two major categories: 1) non-financial plans 2) financial plans

Jan 1, 1983

By R. D. Shackleton

Medusa Cement Company, a division of Medusa Corporation, is a medium-sized cement manufacturer serving the midwest, east, and southeast. Medusa's eight plants are located in Georgia, Pennsylvania, Ohio, Illinois, Michigan, Wisconsin, and Canada. Of these, six have active limestone, shale, clay, and sand quarries now in operation. This paper deals with the various individual state laws regulating mining and reclamation at the Georgia, Illinois, and Pennsylvania quarries. Several recommendations for future state mining laws are discussed also.

Jan 1, 1974

By James K. Ballard

Leach dumps in Butte are relatively new in comparison with older established dumps in other areas throughout the West. With the exception of one 10 million ton dump, all dumps have been formed on a prepared base. This is necessary because the entire leach dump area overlies an alluvial fill which varies in depth from 100 to 400 feet and through which solution would be lost. Preparation of the leach pad consists of first removing all vegetative material and compacting the exposed surface with rollers. This surface is covered with a 4" layer of minus 1" crushed rock which in turn is roller compacted. A 3" compacted layer of asphalt hot mix is then applied to the crushed rock surface. Final sealing is effected by a 1/4'? coating of catalytically applied hot asphalt. Dump leaching was inaugurated in 1964. First solution applied was wholly made up of mine water pumped to surface through a central pump shaft. Sulfuric acid was added on surface at a surge pond to control pH of the leach solution. Acid addition is necessary not only to benefit the leach dumps, but to prevent the formation of ocher scale within the pipe line distribution system. Mine water pH is on the order of 2.8. The combination of ferrous and ferric iron as well as magnesium and aluminum salts is such that ocher forms at a pH of 2.38. It is therefore mandatory to control pH at 2.0. Dump effluent pH is held at 2.3 or less.

Jan 1, 1968

By J. R. Parry

Over the past several years, computerized financial models have been an important part of Newmont's strategic planning process. Two applications will be discussed in this paper: a general purpose financial model of Newmont, and a detailed operational/financial model of Magma Copper Company. Newmont?s general purpose financial model was developed using Lotus 1-2-3. It was designed to aid management in assessing the financial consequences of investment and financing decisions associated with long-term strategic planning by simulating the consolidated effect from individual transactions. Not only is the model capable of assessing the sensitivity of specific decisions to changes in the external economic environment (i. e., commodity prices, interest rates, inflation and exchange rates), it can also evaluate the effect from operating and financial decisions, including changing production levels and cost structures at individual operating units as well as simulating several types of transactions, including equity and debt issues, acquisitions and divestitures. The analysis of Magma Copper Company required the development of a detailed operating and financial model of the Company. The model was developed using IFPS in the corporation?s UNISYS (then Burroughs) B7900 mainframe computer and included separate pro forma financial statements for each of San Manuel-Pinto Valley's mines and concentrators, as well as Magma's smelting and refining operations. The outcome of this analysis was the decision to merge Magma Copper and Pinto Valley Copper Corporation, and to recapitalize the new corporation in order to provide funds for a retrofit and expansion of its Arizona smelter and expansions of its refinery and SXEW facilities.

Jan 1, 1989

By T. Fernandez, V. Juchen, C. Petter, F. Cantini, V. Lenz, V. I. Araújo, R. Petter, R. Darrigo, A. Young, I. G. da Costa, J. Oppermann

There are many methods to estimate costs quickly. One of these is the Parametric Method, where costs are estimated from general algorithms (or curves). Derived from an original tool based on the O’Hara model, a software called MAFMINE was developed. MAFMINE is based on parametric models to estimate investment and operational costs in mining. The software itself is based on the use of a computer model known as client-server. However, the model needs new inputs from advances made by the mining industry, mainly in terms of electrification, automation, digital transformation and preconcentration to face Environmental, Social and Governance (ESG) concerns. Thus, this work was to prepare a new core module ready to incorporate the new technologies aiming to deliver operation and capital costs associated with environmental impact mitigation. The tool generates an order of magnitude estimate for CAPEX and OPEX to establish a very first Discounted Cash Flow (DCF) in a mining venture. For quick evaluations, at a preliminary level, the results are very promising.

Mar 2, 2022

By Liz Diaz, Tacio Ferreira

Capstone Copper’s Pinto Valley Mine faced challenges in recovering rock and ore on final walls because of geotechnical constraints that require restrictions on methods for loading blastholes adjacent to the pit boundaries to preserve wall stability. The operation had been using the same drill and blast designs for years. With changing geology, such as harder rock, as mining progressed, material was being left unmined in final walls because of poor breakage. The amount of unrecovered, unprocessed ore was estimated at approximately 380,000 tons a year generated from an average of 60 final wall blasts performed annually. The engineering team from Capstone and Dyno Nobel engaged to minimize the amount of material left on the final pit walls. This paper presents how we collected data, reviewed design standards, and found opportunities to improve ore recovery from pit final walls without increasing drilling and blasting costs. The results collected from implementing the new design on two benches showed the potential for extra revenue of approximately $3.6 million generated annually from reducing final wall unrecoverable underbreak by nearly 71% on the mine’s highwalls.

Feb 1, 2025

By S. E. Restrepo

In recent years, mining operations have experienced the impacts of climate variability, increasing costs, and changes in the socioenvironmental dynamics of the territories. For this reason, the aggregates industry needs to design and define concrete and immediate actions to address climate change. An appropriate way to achieve this is as follows: • Calculate greenhouse gas emissions, sources, and relevance factor. • Make projections of future scenarios. • Design and implement action plans The proposed climate change mitigation and adaptation projects are logistical optimizations of mining equipment (mitigation). Second is the design of an early warning system to predict possible flooding (adaptation).

Mar 2, 2022

By J. Kretschmann, K. van de Loo, J. Brune

In 2018, the German Federal government decided to phase-out the energy production using coal-fired power plants and to terminate lignite mining completely by 2038 at the latest. This decision will impact approximately 60,000 jobs. It will have an enormous impact on the socioeconomic development especially in all German lignite mining regions. To avoid economic and political friction, it is of utmost importance to achieve a sustainable transition towards a post-mining era and to offer residents in the mining districts perspectives for a good future that include adequate job opportunities. In this context, the German government is providing massive structural aids early on. As previous closure experiences from the German hard coal mining industry have shown, it takes at least a generation to overcome the effects of a strategic closing decision of this magnitude. Therefore, the planned closure process appears to be a long time at first glance. In fact, however, it is not.

Mar 2, 2022

By Evan J. Owen, Virginia T. McLemore

The Zuni Mountains, located in Cibola County, New Mexico is an uplifted area that exposes Proterozoic igneous and metamorphic rocks overlain by Permian and younger sediments. Sedimentary-hosted Cu deposits and fluorite veins in the district have recorded production, but other deposits exist. Proterozoic ultramafic rocks may host Ni and PGE. A recent regional stream sediment survey collected 76 samples as part of an exploration geochemistry course at New Mexico Tech with the goal of assessing the critical minerals potential of the district. Whole rock and trace element chemistry of the sediment samples (<2 mm) show a variety of critical minerals possibly worthy of future targeted exploration including up to 700 ppm As, 2100 ppm Ba, 26 ppm Bi, 25 ppm Co, 640 ppm Cu, 145 ppm Ni, 110 ppm Sb, 170 ppm V, and 500 ppm Zr. Positive correlation between Bi, As, Cu, and Sb suggest that these critical minerals are found together within copper veins related to shear zones in the district. Samples collected from streams that drained outcrop of mafic and ultramafic rocks were found to generally contain more Ni, Co, and V. Samples elevated in Ni will be reanalyzed for PGE.

Feb 1, 2025

By William Gleason

The Society for Mining Metallurgy and Exploration (SME) has a long and proud history of being the world?s leading resource for the dissemination for technical information regarding the fields of mining and mineral extraction and processing. That reputation was met, and maybe even exceeded, with the programming for the Society?s 2014 Annual Meeting in Salt Lake City, UT Feb. 23-26. The meeting drew more than 6,700 attendees to the three-day conference that featured more than 90 technical sessions with 670 presentations. These sessions covered the breadth of the mining and minerals industry, but it was the so-called ?softer issues? that were discussed in the keynote session that kicked off the meeting. The keynote session, ?Community Engagement: Building Partnerships for Mining,? brought together some of the leading voices from the mining industry, as well as some of the top voices from nongovernmental organizations (NGOs) that work in the mining sector. The common ground between the panelists was their dedication to working to ensure a social, economic and environmental balance in the development of mines. ?We wanted to bring these NGOs in to begin a dialogue to see how we can work together,? said SME President Jessica Kogel. ?This is a space that SME has not typically operated in, but one in which SME can bring a technical, scientific voice to the discussion. SME wants to play a leadership role in creating partnerships between the technical, social and economic areas that are crucial to the success of any mining project.? In today?s environment, finding mineral deposits and extracting the minerals in an economically viable manner is just one piece of an increasingly complex puzzle. Earning and maintaining a social license to operate requires careful consideration of local and global impacts. The industry often comes under intense scrutiny when a new project is proposed and, therefore, it must strive to meet the highest ethical and environmental standards. Success requires cooperation and collaboration between the industry, community and NGOs.

By Steven A. Savage

Agrico Chemical Company, as we presently know it, is the result of the coming together of several different fertilizer operations. The Williams Companies, our parent organization, first entered the fertilizer business in 1971, when it acquired the fertilizer operations of the Gulf Oil Company. This gave us, among other things, the manufacturing facility at Donaldsonville, Louisiana. In 1972, The Williams Companies acquired Agrico Chemical Company from Continental Oil Company, bringing in a manufacturing facility and phosphate mines at Pierce Florida. Our Florida Mines are in the region commonly known as the Bone Valley Region of Florida. The majority of the phosphate fertilizer produced in the United States utilizes rock mined in this region. The Donaldsonville Plant was originally built in 1967-68 on the site of the old Faustina Plantation at an approximate cost of $80,000,000. (This plant is commonly referred to as our Faustina Plant.) Until such time as Agrico was acquired from Continental Oil, the Donaldsonville Facility was solely used to upgrade phosphoric acid into finished granular products.

Jan 1, 1986

By T. M. Barczak, Zach Agioutantis

The Support Technology Optimization Program (STOP) has been developed by the National Institute of Occupational Safety and Health (NIOSH) to provide a comprehensive tool for evaluating the performance of available secondary roof support systems and designs based on support strength, convergence, cost, installation time and material handling considerations. This program uses engineering models developed from full-scale testing of numerous supports under controlled loading conditions in the unique NIOSH Mine Roof Simulator load frame to determine the support load-displacement performance as a function of the various sup- port design parameters. Both standing supports, such as wood cribs installed within the entry, and intrinsic supports such as cable bolts, can be evaluated. Support systems can be designed and compared for use in a new mining section or to evaluate potential replacements for an existing design. The support design requirements are defined from 1) estimating the failure height in the immediate roof, 2) in-mine measure- ments of support and strata interaction or development of ground reaction curves from numerical modeling, 3) the performance of an existing support system, or 4) from any arbitrary load and convergence criteria. All settings can be saved to permit resuming an evaluation in progress at a later time. This paper presents the updated MS Windows version of this tool, which can be easily installed and run on a personal computer. This Windows implementation will feature a project and application scenario setup where multiple scenarios can be assigned to one project. Scenarios can then be compared on support parameters and cost. Cost parameters can be provided either as individual cost items or using a price grouping feature. Additional support performance curves and/or additional ground reaction curves will be distributed with program updates as new information is developed. Users can also provide their own support and/or ground reaction curves.

Jun 25, 2024

By Jan Reimann

Increasing individualization with smaller quantities, growing competition from low-wage countries, and the continuous drive towards digitalization are the challenges that industrial companies in high-wage countries must face. The example of the Flender One gearbox modular system demonstrates how consistent standardization and digitalization are the enablers for AI, and thus already enable new business models and business approaches today.

Feb 22, 2026