Search Documents

By S. Gaillard, E. Cauda

"Diesel particulate matter (DPM) is an occupational health hazard in underground mines. It generally occurs in the submicron range, and is often present in the mine atmosphere with significant concentrations of dust particles that tend to occur in the supramicron range. Since dust can interfere with analytical methods to measure DPM, it is often removed from a sample stream using impactor-type size selector (diesel particulate matter impactor, DPMI). Because the DPMI physically removes oversized particles from the stream, its performance may be gradually reduced with aging. Sharp-cut cyclones (SCCs) represent an alternative size selector for DPM sampling applications, with a major advantage being that, by design, they should not be susceptible to rapid aging. This paper presents results of a field study designed to compare the performance of aged versus new/clean DPMIs and SCCs in an underground mine. DPMI aging resulted in clogging of the device, and eventually a reduction of its effective particle cut size – though, when sample flow rate was maintained, DPM sample mass collection was not affected until significant aging had occurred. Under the conditions present for this study, effects of SCC aging were observed to be minimal by the end of the study period. INTRODUCTION Submicron particles are increasingly recognized as significant respiratory health hazards (Cantrell and Watts, 1997; Kenny, et al., 2000; Ristovski, et al., 2012). Diesel particulate matter (DPM) represents a major source of submicron particles in both public and occupational environments (Kittleson, 1998; Abdul-Khalek et al., 1998). Due to their work around large equipment in confined spaces, underground miners have some of the highest exposures to DPM (EPA, 2002; Grau et al., 2004). DPM largely consists of solid elemental carbon (EC), commonly known as “soot”, and organic carbon (OC) that may be sorbed to EC particles (Kittleson, 1998; Abdul-Khalek et al., 1998). EC and OC can be measured by thermal-optical methods such as the NIOSH 5040 Standard Method (Birch, 2016), and their sum is referred to as total carbon (TC). While the complex nature of DPM does not allow for its direct measurement, both TC and EC have been accepted as suitable surrogates for monitoring occupational exposures to DPM (Noll et al., 2007 and Birch, 2016)."

Jan 1, 2018

By R. W. Ballmer

Prior to initiating construction of a new mineral development project, sponsoring organizations must be convinced that the operation will be viable. Proof is typically provided by the feasibility study. Considerable man hours will be spent in assessing and evaluating data on the deposit, its environment, and the means of development. Impact studies must be made for various scales of operation, inclusion of by-products, new methods of treatment, deferent levels of integration, and infrastructure configuration. Examples of current materials handling cost estimates are provided from the ongoing investigation in which Amoco is a participant at Ok Tedi in Papua New Guinea and Gag Island in Indonesia.

Jan 1, 1979

By R. J. Gray

Oxidation of coal can best be described as a process of deterioration, since most of the uses of coal, such as for fuel and by-product chemical and coke production, are adversely affected by coal oxidation, and the inclusion of oxidized coal in most coal products detracts from their value. There are probably many mechanisms of coal oxidation, and the ways oxygen molecules combine as complexes with coal macromolecules to form new substances have been dealt with and speculated upon by many workers1)* but are not dealt with in the present work. This study deals with tests and methods of detecting oxidized coal, with particular emphasis on the microscopically discernible changes that accompany the chemical and physical changes that affect the technological properties of coal during oxidation.

Jan 1, 1974

By J. M. Pachter

Property sales and acquisition are prominent features of today's coal industry. Before selling or buying a site, a company must know the property's economic net worth. Any evaluation of economic net worth would be inadequate if determinations of a property's environmental liabilities and costs were omitted. Short-term and long-term costs can result from liabilities related to reclamation, water treatment, subsidence, and hazardous waste disposal. A structured, interdisciplinary approach can aid in the delineation, summation, and scheduling of these costs and liabilities.

Jan 1, 1986

By O. M. Wicken

Magnesite has the unique combination of properties that make it useful in a wide variety of metallurgical applications. The use of refractory magnesite has been increasing throughout the world, but the source of the "ore" differs. The United States has increased production of synthetic magnesites while the rest of the world is exploiting its resources, using natural magnesites. The history and methods of manufacturing synthetic magnesite are discussed as well as the practices for beneficiating natural magnesite. The properties, costs, and uses of the two types of magnesite are discussed and compared.

Jan 1, 1964

By R. H. Sergent

The interest in using halogens for extracting precious metals from ores has increased due to changes In ore characteristics, environmental concerns and regulations. The rediscovery of halogen leaching capability has been the topic of these and other writers1-30. Much work has been done on the performance of bromine, chlorine and iodine5-29. Of these, bromine and chlorine look most promising. Iodine is quite expensive and sometimes forms an Insoluble film on a precious metal surface22,23. Little experimental work has been published on the relative performance of bromine versus chlorine. The Pourbaix diagrams for the halide leach system (see Fig. 1-4) Indicates a significant stability advantage for bromine In forming complex ions with gold. This should result In greater extraction of gold under similar leach conditions and Is evaluated In this work. The regeneration of halogen from a spent leech solution is a critical requirement for an environmentally acceptable halogen leach process. Bromide can be oxidized In-situ to bromine ~ adding chlorine or ozone2,31. Bromide like chloride can be oxidized In an electrochemical cell to produce halogen on demand 13,15,17. Bromine clearly offers a number of possible regeneration pathways. This work strives to compare the relative ability of chlorine and bromine to extract gold from partially and fully oxidized ores. A commercially pressure oxidized sample was evaluated under a number of experimental conditions. The autoclave feed ore from the same mill was also evaluated after complete oxidation In a laboratory autoclave.

Jan 1, 1993

By Ross Glanville

The Optimum Production Rate (OPR) is one of the most important parameters in the evaluation of a mineral deposit. The OPR cam also be expressed as the Optimum Mime Life (OML) in years since the expected mime life is determined by dividing the OPR per year into the estimated ore reserves. Unfortunately, very little time and effort has been directed towards the determination of the OPR. Instead, "rules of thumb" are often applied to select a mime life without due consideration of the economic implications of such a selection. A "justification" for a particular production rate is often based on a pre-conceived arbitrary requirement for a mime life of 5, 10, or 15 years, for example. In this paper it is demonstrated that such arbitrary selections for high-grade/low¬-tonnage mines (such as many underground gold/silver deposits) often lead to sub¬optimal results. In fact, am apparently uneconomic deposit at am arbitrary production rate may be economic at the OPR. Consequently, investment opportunities may be overlooked if one analyzes mime' properties based on arbitrary production rates.

Jan 1, 1984

By R. L. Loofbourow

Reasons for reexamining underground mining include: 1. The assurance that more deep deposits of useful minerals will be found. 2. The existence of deeply covered deposits of industrial minerals near large markets where quarries are becoming depleted or are lacking. 3. Surface property values, zoning and other limitations on open pit mining. 4. Expectation that underground space will be increasingly used for transportation, power plants, storage and similar purposes. 5. The improvements which have been made in underground mining. During the last three or four decades many changes and improvements have been made underground. All underground construction and mining has benefitted to some extent but the effect on the productivity of labor employed with some methods- has changed little and the use of these methods has declined. Productivity of labor in other methods has increased substantially. The relative usefulness of mining methods has changed and a vital industry, bituminous coal, has been returned to health. In this paper, consideration is limited to nine methods used with high productivity during the period under review. These methods are not necessarily better than others but they may be considered the prime methods in the sense that, in our economy, many, low grade ores, coal and the principal industrial minerals could hardly be produced by less productive means.2 Although most of the examples cited are from mining as such., the first four methods discussed can be used for the construction of stable excavations of various' shapes in sound rock.

Jan 1, 1967

By W. R. Reed, G. J. Joy, B. Kendall, A. Bailey

"Testing of the NIOSH-designed roof bolter canopy air curtain (CAC) has gone through many iterations demonstrating successful dust control performance under controlled conditions. J.H. Fletcher & Co. (Fletcher), an original equipment manufacturer of mining equipment, has further developed the CAC concept by incorporating it into the design of its roof bolting machines. A new CAC design has been developed incorporating the results of testing of the NIOSH design and the recent Fletcher design. Observations from smoke testing conducted on this new CAC design in a laboratory setting show promise for improved performance. INTRODUCTION Exposure to respirable coal mine dust can cause coal workers’ pneumoconiosis (CWP) otherwise known as black lung. If silica is present in the dust, the miner may develop silicosis in addition to CWP. CWP and silicosis are occupational respiratory diseases that are ultimately fatal and have no cure. The only method of prevention is through elimination of exposure to respirable coal mine dust and crystalline silica (quartz). The current occupational exposure limit (on an MRE basis) for respirable coal mine dust is 2.0 mg/m3 during each shift that a miner is exposed in the active workings of the mine or in mine facilities [30 CFR 70.100 2015]. Recently enacted legislation changes this standard beginning in August 2016 to 1.5 mg/m3 for a full working shift [Federal Register, 2014]. If the respirable coal mine dust contains more than 5% silica, the applicable respirable dust standard is reduced; calculated as 10 divided by the percent quartz present [30 CFR 70.101] so that the effective exposure limit for respirable quartz is 0.1 mg/m3 for a full working shift. Sources of exposure to respirable coal mine dust for the roof bolting occupations include infrequent maintenance and cleaning of the vacuum dust collection system and operating the bolter downwind (in the return air) of the continuous miner [Goodman and Organiscak, 2003]. Recent studies have demonstrated that vacuum dust collection systems are effective in capturing bolter-generated dust, if maintained and operated correctly and if proper face ventilation techniques are used. However, most exposure to respirable coal mine dust for the roof bolter occurs when the roof bolter machine is operated downwind of the continuous miner [Potts et al., 2011; Colinet et al., 2013]. Because of this higher exposure downwind of the continuous miner, the roof bolter is generally limited to working downwind of the miner only once during a production shift"

Jan 1, 2016

By R. Jacobson

This paper presents comparison of proposed future solution and in-situ mining methods for in-situ leaching and recovery of uranium, gold, silver, and copper. We propose to show that in the future new extraction methods for each metal will eventually evolve for each hydrometallurgical process step, i.e. in-situ leaching, recovery, and concentration; precipitation and reduction; and drying, when required--without generating waste or bleed streams. In the future, to be highly profitable, these forms of mining will develop into an integrated system to eliminate waste streams using safe, powerful lixiviants. This integration will include, with some exceptions, improvements in the following areas of process development: 1. Lixiviant selection and in-situ leaching technique, 2. Target metal recovery and concentration (at a surface hydrometallurgical facility) from the circulating pregnant lixiviant stream, 3. Target metal precipitation or reduction, where decant water from the precipitate dewatering step is reusable for resin or solvent strip liquor (eluant), 4. Final preparation of target metal for sales, i.e. drying, purification, casting, packaging, 5. Restoration where most of the groundwater restoration process is performed at the same rate as multi-wellfield mining.

Jan 1, 1987

By R. L. Braun

In situ chemical mining of primary sulfide ore requires distribution of injected oxygen in a large underground flooded region of broken ore. Although the maximum oxygen content of the leach solution will be dictated by the operating temperature and hydrostatic pressure, the actual oxygen content will be limited by the geometric dispersion of the injected oxygen, the rate of dissolution of oxygen, and the rate of convective circulation of oxygenated solution within the flooded bed of ore fragments. These factors are examined by a detailed theoretical analysis supported by laboratory experimental data. Typical results of the study illustrate that adequate dissolution of oxygen and circulation of oxygenated solution can be obtained in a column of 4 million metric tons of broken ore by using three gas injection lines and an oxygen injection to consumption ratio of 1.84.

Jan 1, 1974

By Salvatore] [Parand

Deep well disposal is a much used and abused term which is the panacea for wastewater disposal in some minds and creates near hysteria in others. It can be the answer to a difficult waste disposal problem, or if improperly employed, can create more problems than it solves. My purpose in this presentation is to focus on the value and limitations of deep well disposal as expressed by New York State's experience and policies. To he sure, I feel a place for such practices docs exist if adequate safeguards are utilized. I shall give a broad brush approach to New York's legislative, geologic and operational concerns and speak briefly on some case histories. I shall not delve deeply into the technological details since I am not an expert in mining exploration or well drilling.

Jan 1, 1973

A comprehensive understanding of the effects of autoclave configuration (batch, semi-batch, continuous) on the residence time necessary to achieve a target conversion is a prerequisite for design of commercial scale autoclaves. Particle size distribution, mineral and reagent concentrations, temperature and mixing also influence the conversion. This paper outlines the bases of using test data to predict performance of commercial scale autoclaves. Recommendations for coordinating test program design with selection of scale-up method are provided. Examples are given to illustrate the different levels of engineering effort needed to meet corresponding levels of design optimization and accuracy.

Jan 1, 1998

By Richard W. Patton

With the advent of the Clean Air Act and the installation of flue gas desulfurization (FGD) equipment (scrubbers) on coal fired power plants, the management of solid wastes has taken on added importance. Aside from the large amounts of fly ash and bottom ash usually generated, large quantities of liquids in the form of scrubber sludge are also produced. These wastes must be disposed of within the constraints of land and water quality regulations. This paper describes the practices adopted by the electric utility industry in denting with this problem, including methods of generation and treatment, quantities and characteristics of the materials, and transportation and disposal practices. The paper also briefly describes final product characteristics and several applications for commercial utilization and land reclamation.

Jan 1, 1983

By K. E. Harrison

The acid rain legislation has passed into law. This new law has caused the power generation community to investigate alternative methods to obtain compliance with the new legislation. One thing all of the power companies have concluded is the answer is not easy. Do we switch fuels to burn all low sulfur compliance coal? Maybe possibly only partial desulfurization by means of a dry sorbent system? Or, finally, maybe a wet scrubber system? Whatever the choice, the power community needs to investigate all of the alternatives. In 1988, ICF Kaiser Engineers, Inc. (ICF KE) responded to a request by the U.S. Department of Energy for the engineering development of advanced physical fine coal cleaning. ICF KE responded and was awarded a contract to conduct a multi-task program to develop an advanced flotation system to eliminate pyritic sulfur and retain as much energy as possible. ICF KE assembled a team that included members of industry, academia, and industry research organizations to conduct this multi-task program. The program includes sixteen (16) tasks. This team had personnel to help solve some of the anticipated problems and to provide industry prospective on the viability and commercial potential for any concepts proposed. The primary team consists of a major coal producer, Babcock and Wilcox, Eimco Process Equipment Company, and Virginia Polytechnic Institute and State University.

Jan 1, 1992

By Myles E. Robinson

Significant changes in the markets for coal have taken place since World War II, As used in this study the term ?coal? will refer to bituminous coal, The anthracite industry in size, characteristics, and problems differs materially from the bituminous coal industry, These changes have both influenced and been influenced by the mechanization of mines, and by decreased distribution costs, especially in transportation. It is the purpose of this paper to examine these post-war changes, to assess their impact upon the production and distribution of coal, and to explore future market developments in the light of past and present trends and relationships. The layman lacks adequate informatian on the production, demand, and distribution of coal. There are two reasons for this. First, there is a relative lack of statistics coveting the industry, Coal operators and distributors are not required to file with any government agency the type of much more complete statistics filed by the railroads and public utilities with national and State agencies. The Bureau of Mines assembles much useful information on the coal industry, but several areas, including that of investment and finance, have no central depository which can be used to keep the public informed of the nature and extent of the industry and its problems.

Jan 1, 1964

By John Bley

White Pine Copper Company operates a mine in the Upper Peninsula of Michigan using a modified room-and-pillar system for extracting ore.1 Mine production averages 15, 500 tons per day. The terrain is predominantly level and the depth of cover varies from 500 to 800 feet over the present workings with depth increasing as mining progresses down the dip. The deposit is situated on a low angle plunging, anticlinal structure composed of sedimentary beds. Local terminology for the stratigraphic units which contain the ore horizons, named in ascending order, is as follows: lower sandstone, parting shale, upper sandstone and upper shale. The ore zones of copper enrichment are, contained in the parting and upper shales. The parting shale will vary; from 6. 5 to 9.0 feet thick; the upper sandstone from 2 to 10 feet; and the upper shale from 1. 5 to 6. 5 feet. Two variation of the room-and-pillar system are used to extract the ore depending on grade and local ground conditions. One system is called the parting shale method and recovers the parting shale only. This system requires a mining height of 8 1/2 feet to accommodate large-scale, high-capacity equipment and this working height is obtained by removing approximately 1 to 2 feet of the barren lower sandstone with the ore. Under the second system, locally termed full column, the mining height is about 14-1/2 feet and this system removes the parting shale, the upper sandstone and the lower mineralized zone, approximately 1-1/2 feet, of the upper shale at which point it is possible to maintain a competent back (Fig. 1).1

Jan 1, 1964

By S. Middlemiss

The Indentation Fracture technique is being developed as a tool for use in comminution and mineral liberation analysis. Fracture toughness measurements for a number of mineralogical materials were made and comparisons were drawn between these and properties measured with the Ultrafast Load Cell drop weight apparatus. The technique has also been used as a probe to quantify differences in fracture properties at different areas in the microstructure of a material. In both a Utah limestone and a South African quartzite, material near a grain boundary fractures very differently to that in the bulk. Ongoing work is ultimately aimed at producing a comprehensive fracture model for a multi-mineral system based on its micro-fracture characteristics.

Jan 1, 1994

By W. A. Haley

Wheel loaders were first introduced shortly after World War II as small machines designed for handling loose materials in various industrial and processing applications. It was not until the early 1950?s, however, that machine size permitted widespread loading of loose or stockpiled material into on-highway type trucks. An ever increasing number of machines continue to be used for this purpose today. In fact, it is by far the major use for wheel loaders in mining and quarrying. Many of these loaders were working at mines or quarries handling in-process or finished material and some were doing shovel clean-up. It was quite natural then, when the primary pit loading shovel was down, to attempt to maintain some production by replacing it temporarily with the wheel loaders. Most of these attempts were not very successful, however, until the really large wheel loaders, 4- to 6-yd. size were introduced in the early 1960's. Since that time these machines have proven they can be productive and economical primary pit loading tools, a job that was once the exclusive domain of the power shovel. To be competitive with the shovel however, conditions must exist or be made to exist, that will be favorable for the wheel loader.

Jan 1, 1967

By S. Gaillard, E. Cauda

"Diesel particulate matter (DPM) is an occupational health hazard in underground mines. It generally occurs in the submicrometer size range and is often present in the mine atmosphere with significant concentrations of dust particles that tend to occur in the supramicrometer size range. As dust can interfere with analytical methods to measure DPM, it is often removed from a sample stream using an impactor-type size selector such as the DPM impactor (DPMI). Because the DPMI physically removes oversized particles from the stream, its performance may be gradually reduced with aging. Sharp-cut cyclones (SCCs) are an alternative size selector for DPM sampling applications, with a major advantage that, by design, they should not be susceptible to rapid aging. This paper presents the results of a field study designed to compare the performance of aged versus new/clean DPMIs and SCCs in an underground mine. DPMI aging resulted in clogging of the device and, eventually, a reduction of its effective particle cut size, but when sample flow rate was maintained, DPM sample mass collection was not affected until significant aging had occurred. Under the conditions of this study, the effects of SCC aging were observed to be minimal at the end of the study period. IntroductionSubmicrometer-sized particles are increasingly recognized as significant respiratory health hazards (Cantrell and Watts, 1997; Kenny, Gussman and Meyer, 2000; Ristovski et al., 2012). Diesel particulate matter (DPM) represents a major source of submicrometer particles in both public and occupational environments (Kittelson, 1998; Abdul-Khalek et al., 1998). Relative to other occupational groups, underground miners can have some of the highest DPM exposures due to their work in confined spaces where large diesel equipment is used (U.S. Environmental Protection Agency, 2002; Grau et al., 2004). DPM largely consists of solid elemental carbon (EC), commonly known as soot, and organic carbon (OC) that may be sorbed to EC particles (Kittleson, 1998; Abdul-Khalek et al., 1998). EC and OC can be measured by thermal-optical methods such as the U.S. National Institute for Occupational Safety and Health (NIOSH) 5040 standard method (Birch, 2016), and their sum is referred to as total carbon (TC). While the complex nature of DPM does not allow for its direct measurement, both TC and EC have been accepted as suitable surrogates for monitoring occupational exposures to DPM (Noll et al., 2007; Birch, 2016)."

Jan 8, 2018