Search Documents

By K. C. Kocsis

"Diesel-powered equipment has allowed the mining industry to raise production rates and significantly improve productivity, as it is rugged, mobile and reliable, but its widespread use in underground mines has generated concerns regarding the exposure of mine workers to harmful diesel engine exhaust gases and particulate components such as diesel particulate matter (DPM), which has recently been classified as a human carcinogen by the International Agency for Research on Cancer. The agency expressed further concerns that workers’ exposure to high DPM concentrations can increase the risk of cardiovascular, cardiopulmonary and respiratory illnesses. Three emerging technologies could have the ability to replace dieselpowered equipment and remove DPM from underground mines: fuel-cell-powered mining equipment, battery-powered mining equipment and advanced material handling systems. This paper reviews them and assesses whether they have reached the point where the pollutants emitted by diesel-powered equipment can be removed from underground mines through the introduction of zero-emission mining equipment and power systems. Information is also provided from the results of a feasibility study, including a detailed cost benefit analysis, carried out at six Canadian and nine U.S. underground mines, which looked at the possibility of replacing diesel-powered production equipment with fuel-cell-powered equipment. The remarkable pace at which battery technology is progressing is also reviewed, and the feasibility of replacing diesel-powered mining equipment with battery-powered equipment is assessed. IntroductionHazardous pollutants in underground mines. Why is it important to remove diesel particulate matter (DPM) from underground mines? Over the past 40 years, diesel-powered equipment has allowed the mining industry to achieve rising production rates and major improvements in productivity, as the diesel engine is an economical source of power and diesel-powered equipment is usually rugged, mobile and reliable. On the negative side, the toxicity of some diesel exhaust gases is well known (Grenier et al., 2001), and the widespread use of diesel-powered equipment in underground mines has generated increasing concerns about the occupational exposure of mine workers to harmful diesel engine exhaust gases and particulate components such as DPM. Diesel equipment also entails other hazards like heat and humidity. Exposure to excessive heat can cause heat illnesses, such as heat rash, heat exhaustion and heat stroke (Donoghue, 2004; Roghanchi et al., 2016), and a hot and humid underground environment negatively affects the efficiency of the workforce, which may result in a decline in production output (Roghanchi et al., 2017)."

Jan 10, 2017

By Brahm D. Prasad

As in other mineral deposits, variation in bitumen saturation, thickness of ore and discard occurs throughout Alberta's Athabasca Oil Sands deposit. The economic stripping ratio developed here to determine surface mineable limits takes into account capital and operating costs, crude oil prices, quality of ore, thickness of overburden, and thickness of inter-ore waste. The surface mining systems employed to remove bituminous sands (oil sands) from huge mines at depths of 60-70m use gigantic draglines, bucket wheel excavators and reclaimers, and large mobile equipment.

Jan 1, 1982

By J. P. Allen

Cobalt, nickel, and manganese can be recovered quickly, cleanly, and selectively from cobalt-rich manganese crust by leaching in dilute acid solutions in the presence of hydrogen peroxide. Common selective precipitation methods can then be used to recover these metals from the leach liquor. The leaching reaction produces only oxygen as a byproduct, and the waste residue from leaching was tested and found to be non-hazardous under existing EPA specifications. The leaching process is effective in either fresh water or seawater. This research is a part of the Bureau of Mines program to identify the mineral resources of the Exclusive Economic Zone and devise methods for recovering their valuable components.

Jan 1, 1990

By Duane L. Abata

This paper discusses recent technology dealing with the use of computer graphics in the mining industry and presents a newly developed computer software package specifically designed for use in underground mining operations. This software package, developed under a United States Bureau of Mines contract, 1) displays mine ventilation schematics and other representative illustrations for a real time data acquisition system and 2) utilizes the Bureau-owned Minefire and Ventilation Code for display of ventilation and contamination predictions on the microprocessor system. The package utilizes a unique system of display indexing that provides a simple yet efficient method of recalling a series of mine schematics detailing an underground operation and an alarm acknowledgement scheme that provides an effective method of identifying problem areas which may exist in the mine network. The package was written in Fortran for a 64 kilobyte, Z80-based microprocessor-computer.

Jan 1, 1984

Since the beginning of the computing age, technical software packages have not been developed to address only programming specialists but have been dedicated to process engineers. For process analysis, BRGM is developing and commercializing three packages: ? sampling software: ECHANT 2.0 for Windows ? material balance calculation: BILCO 2.0 for Windows ? steady-state simulator for plant design, adaptation and optimization: USIM PAC 2.1 for Windows This paper deals in a first part with the main features of these three packages. In a second part, advanced models are presented for SAG/ AG mills and flotation columns. An industrial case of application is shown for each of them.

Jan 1, 1997

By Joseph J. Yancik

An exchange of coal mine specialists was made with the USSR under an "Agreement on Exchanges and Cooperation in Scientific, Technical, Cultural, and other Fields for 1972-73," which was signed by President Nixon and Chairman Breshnev on April 11, 1972.* This exchange, in the field of coal mine safety and scientific research in hazard control technologies, was one of 16 technical exchanges covered under the above agreement. A six-man USA delegation visited the Soviet Union from September 9 to September 21, 1973. The delegation visited four deep mines, three in the Donets Basin and one in the Moscow Basin, a State Safety Research Institute, a Mine Research Station and associated Research and Design Institute, two Research and Design mining equipment institutes, and a Trade Union-sponsored health sanitarium. In Moscow, the delegation received a briefing on the Soviet coal industry from First Deputy Minister Vladimir Fedanov. A similar briefing was given to us on the Donets coal basin by the Deputy Minister S. Saratikyanz of the Ukrainian Coal Ministry. Lengthy technical discussions were held with the mines staff and research personnel at the institutes we visited. In addition, we had detailed discussions with key staff members of two combinats "Donetskugol" and "Tulaugol." In all these meetings, principal topics were matters of safety related to hazards associated with face mechanization, coal transport, methane gas control measures, gas outbursts, coal and rock outbursts, fire fighting add control, explosion suppression and control measures and other related hazard factors. There was also much discussion on miner training, miner's attitudes toward safety and accident prevention practices, and preparation and enforcement of safety rules and regulations. The delegation was very warmly received and constant attention was given to our needs. Our numerous questions were answered with candor although quite often in not as much detail as we would have liked.

Jan 1, 1974

By S. Natansohn

A prevalent technique for the recovery of silver from wastes generated in silver-tungsten electrical contact fabrication is electrowinning. Such scrap is placed in a permeable plastic basket which constitutes the anode compartment and this basket is suspended in a larger cell in which the cathode is mounted. A silver nitrate solution is used as the electrolyte and, upon application of an electric field, the silver migrates to the cathode where it deposits out. At times, there is tungsten migration to the cathode compartment and consequent co-deposition with the silver. This W contamination, which may amount to several thousand ppm, necessitates additional purification of the deposited Ag and its removal would therefore be advantageous. The elimination of the W impurity would also extend the operating period of the cell with corresponding increase in the Ag output and savings in labor costs.

Jan 1, 1982

By Hemendra N. Kalia

Several attempts have been made in the past sixty or so years to commerciliaze the vast oil shale deposits of the United States of America. However, the industry has yet to become viable and economic. To date, it has not been possible to produce oil from the oil shales at a competitive price when compared to the oil produced from oilfields by conventional methods. However, the development work has been quite fruitful in furthering the art of thick bed mining and technology of in situ retorting. The in situ method has the potential of recovering oil from thick beds and the resource recovery potential is much greater than that from underground mining and surface retorting. In situ methods require that the shales/ marlstones be fragmented ' in place to induce adequate porosity and permeability to allow in situ' heating of the fragmented shales. This can be accomplished by using explosives. However, it has been found that the existing blasting systems, though very efficient, are somewhat lacking. The explosive become insensitive when shot in multiple vertical decks. They can also become insensitive when spaced horizontally at close proximity to other charges. Also, since the blasting is done in a very limited free face, this limits the delay time that can be allowed between charges. Consequently it is not always possible to predict the performance of the blasting system on a routine basis. Furthermore, since it is not possible to undertake secodary blasting, it is imperative that the blast design function properly. Recent, successful retorting by Occidental Petroleum Company of retorts seven and eight suggests that some of these problems may have been overcome. This paper addresses some aspects of in situ retorting and problems those have impeded the development of a viable oil shale industry in the U.S.A.

Jan 1, 1983

By Harold E. Rowen

The listed title of my talk to-day is "MODERN ON STRAND SINTER COOLING". Perhaps it should he ve been "COMPLETION OF SINTERING ON THE STRAND" as the two are synonymous. By the very nature of the DWIGHT-LLOYD SINTERING PROCESS partial cooling on the strand is always present, but not completion of sintering and cooling on the strand. I have mentioned the Dwight-Lloyd process just to be certain the type of sintering under discussion is fully identified because some of the basic mechanisms of sintering occur in various pyro-processing of fines lying in close quiescent contact, such as powdered metals practices, some types of pellet induration, firing of briquets, or other compacts, where the entire bed is brought to, and held at, the high reaction temperatures of sintering. Figure 1, The continuous sintering process as originally conceived consisted of intimately mixing carefully proportioned burdens, placing them in a comparatively thin, draft permeable layer, on a moving grate and igniting the surface while drawing sir through the bedded burden. The moving grate was advanced slowly as the line of burning fuel travelled from the surface to the bottom of the bed and no more fire zone could be seen.

Jan 1, 1973

By George Innes

The soda ash business in the United States has undergone a sweeping technological change in ihe last 20 years. In a world where synthetics are continuzlly replacing natural products, here we have exactly the opposite, a syntheric chemical being replaced by a natural product. This change is nearly complete in the U.S. and is beginning to take place in Europe and other parts of the world.

Jan 1, 1980

By M. Sears, K. Mohamed, J. Addis, J. Wickline, G. Rashed

To better understand the load shedding and the stress transfer on coal pillars due to room-and- pillar retreat mining in deep cover panels, researchers from the National Institute for Occupational Safety and Health (NIOSH) conducted a monitoring field study. Two sites, at overburden depths of 1,000 ft (304.8 m) and 1,500 ft (457.3 m), were selected in a room-and-pillar mine operating in Southern West Virginia. The deformation and stress changes in the roof and two adjacent pillars at each site were monitored during the retreat mining process. The monitoring results and field observations were used to calibrate large-scale FLAC3D models for each site. The calibrated models were used to assess different sizes of roof bolts installed in deep cover areas. INTRODUCTION Deep cover room-and-pillar retreat mining is an important emerging issue that will intensify in the future as shallower reserves are depleted (Mark, 2009; Chase et al., 2002). During pillar retreat mining, the likelihood of local and/or global instabilities increases due to elevated stress levels near the pillar line because of the abutment loading. In the last decade, approximately 31% of the room-and-pillar mining groundfall fatalities in the United States occurred during pillar retreat mining. Between 2013 and 2017, this proportion increased to 55%, of which 50% of these fatalities were due to falls of roof and rib that occurred during pillar recovery (MSHA, 2018). One interesting piece of information about pillar recovery fatalities was that the victim was nearly always under bolted roof. Sheared and broken #5 (5/8-in), fully grouted rebar bolt failure contributed to three of four fatal roof fall incidents that have occurred in deep cover retreat mines (NIOSH, 2010). This claim raised the following question at the study mine: Is it safe to use a 4-ft long #5 (5/8-in) rebar bolt grade 60 at a depth of cover more than 1,000 ft (304.8 m)? There was some concern about shear failure of the #5 (5/8-in) rebar bolt at a depth of cover over 1,000 ft (304.8 m). To answer the question and to reduce accidents and fatalities caused by ground falls due to room-and-pillar retreat mining in deep cover panels, the National Institute for Occupational Safety and Health (NIOSH) monitored the roof and rib deformation and the change in vertical pressure within two adjacent pillars during pillar recovery. The study was conducted at two deep cover sites in a room-and-pillar mine located in Southern West Virginia that operates in the Lower War Eagle (LWE) seam. The monitored sites were selected at 1,000 ft (304.8 m) and 1,500 ft (457.3 m) depths of cover. In this paper, site-1 represents the monitored site at 1,000 ft (304.8 m) of cover, while site-2 represents the monitored site at 1,500 ft (457.3 m) of cover. For this study, large-scale FLAC3D numerical models were calibrated based on both field observations and instrumentation results. The calibrated models were then used to compare the ground response and the induced stresses of two pillars at instrumented sites 1 and 2. The maximum lateral displacement (roof shift) obtained from the calibrated large-scale FLAC3D models was applied to a small-scale FLAC3D bolted models, the safety factor for axial stresses of the simulated roof bolts was calculated at the deep cover sites.

Jan 1, 2019

By R. Froidevaux

Geostatistical estimation techniques were customized to enable forecast of production figures at the Silver Bell uranium mine (Uravan District). Surface drill hole data were used to provide a block model of kriged estimators of average uranium grades. The recoverable figures, such as ore-waste ratio and ore grade, are then deduced from regressive curves previously obtained from underground information and production data. Cross-validations of the entire model were performed and were found positive.

Jan 1, 1981

By L. Giraldo, S. Cotten

"INTRODUCTION The vision for a “Mine Escape Vehicle” (MEV) is to provide capabilities to better enable underground travel to allow miners to escape to safety in the event of a major mine emergency such as a fire or explosion. Enhanced transportation and survival capability such as a MEV may have minimized or eliminated the loss of life associated with several of the mine disasters that occurred in 2006, which together resulted in the deaths of 19 miners. Although the most desirable response in an emergency is for the miners exit the mine, if escape proved to be impossible, the miners could use the vehicle to proceed to an underground point of refuge to await rescue. Under a NIOSH contract issued in April 2008, Raytheon developed a conceptual vehicle design including (1) the capacity to provide life support functions for a number of miners, (2) operate in a reduced oxygen atmosphere with little or no visibility, and (3) travel at speeds faster than miners could walk out of the mine. The proposed MEV concept envisioned modification of a personnel carrier (a.k.a. a “mantrip”) that would be used every day during normal mine operations, not a specialized vehicle reserved only for or dedicated solely to escape. The MEV concept also included escape aids that are detachable from the vehicle in the event that the vehicle must be abandoned on the way out of the mine and the dismounted miners had to proceed on foot. To advance MEV development, NIOSH awarded a second contract in 2010 to Raytheon to build, test, and evaluate the performance of a proof-of-concept MEV that culminated in a 7-month performance evaluation of vehicle in an Eastern Kentucky coal mine (Figure 1). User feedback and lessons learned from the proof-of-concept vehicle evaluation provided support for the general MEV approach, guidance related to the practicality of MEV capabilities, and indication of specific technology shortcomings for this application."

Jan 1, 2015

By K. L. Lamb

At the Sierrita mine, 40 km (25 miles) south of Tucson, Arizona, Duval Corporation is rapidly gaining operating experience with its new Portable Crushing and Conveying System, (PCCS). As of November 23, 1983, over 4.5 million tons (5.0 million st) of ore have passed through the system. Mining cost per ton for the months of July, August and September was 83% below the average for the first five months of 1983. Although all the cost reductions experienced cannot be attributed to the Portable Crusher, it was a major contributing factor. The Sierrita ore deposit has several natural topographic and geologic conditions which are not favorable to mining. It is not a sidehill deposit and therefore no low-level exit points exist to facilitate truck haulage. The ore is very hard. Quartz diorite, hardest of the three major rock types, averages 172-207 MPa (25-30 000 psi) unconfined compressive strength and may run as high as 345 MPa (50 000 psi). Blasting in this rock produces oversize material which runs approximately 20% 51 centimeters (20 inches). The ore is low grade, averaging slightly better than .30% contained copper and .035% contained molybdenum, with small amounts of silver. These conditions, plus high design production tonnages, make the Portable Crushing and Conveying System (PCCS) practical for Sierrita. Without crushing and conveying, truck haulage would be prohibitively expensive. A typical, October, 1983, ore haul from the bottom of the pit would involve a vertical lift of 260 meters (850 ft) and a horizontal distance of 3 860 meters (12 200 ft) were not in-pit crushing and conveying available. The corresponding cycle time would be nearly 32 minutes.

Jan 1, 1984

By Guoqing Li, Hao Wang, Nailian Hu, Victor Tenorio, Jie Hou

This paper presents an algorithm for optimizing the scheduling of trackless equipment in underground mines. With the shortest working interval and maximum productivity as goals, a genetic algorithm (GA) is used to solve the problem, and obtain the optimal working sequence with the most suitable equipment configuration possible. The input for the proposed method is the number of units and capacity of trackless equipment, the production process, ore amount in stopes, and the distance between stopes. The algorithmis verified using four setups of 5 stopes with 5 cycles, 5 stopes with 15 cycles, 10 stopes with 10 cycles, and 10 stopes with 30 cycles. The solution time of the algorithmis no more than 20 min, which is acceptable for practical applications. The results show that the setup of 10 stopes with 30 cycles is closer to the actual production of the mines, and the optimization model can effectively improve the operation efficiency. In this scenario, the robustness of the optimization is tested by simulating equipment failure events. Under the condition of 8% failure rate, the operation time is extended over 3.21–14.56% than expected, which represents strong robustness. The algorithm can quickly provide a feasible and effective solution for the production scheduling decision of trackless equipment in underground mines.

Aug 12, 2020

By Ranajit Kumar Sahoo, Shatrughan Soren, Surendra Kumar Biswal, Soumya Sahoo, Sachida Nanda Sahu

The presence of appreciable quantity of clay mineral in Indian hematite ore needs an attrition technique using screw scrubber in the beneficiation circuit to remove the ultrafine clays and avoid downstream operational problems. Spectroscopic analysis revealed that iron ore samples obtained from the Barbil region of Odisha contain a high amount of silica and alumina in the form of clay minerals (e.g., kaolinite) contributed as a loss on ignition (LOI) in the iron-making process. Iron ore fines of below 10 mm size were subjected to a laboratory-scale screw scrubber, and the effectiveness of scrubbing as well as the pelletization of the scrubbed product was investigated. The screw scrubber in the beneficiation circuit helps to remove the clay minerals, causes an increase in iron values from 63.65% Fe(T) to 66.18%Fe(T), with improved physical (CCS of 325 kg/pellet) and metallurgical (RDI of 2.24%) pellet properties.

Aug 31, 2020

By Ramiro da Conceição do Nascimento, Horst Guenter Feldhagen, Rafael Piumatti de Oliveira

Mixed hydroxide precipitate (MHP) is a nickel intermediate product that has economical benefits to downstream leaching of lateritic marginal ores. Usually, this product is subsequently processed and refined to produce nickel by hydrometallurgy, but an alternative route can be made integrating hydrometallurgy and pyrometallurgy. Assessing the overall consumption of ferroalloys to obtain stainless steel, as an increasing practice performed in China, the synergy of nickel extraction from laterites by leaching and precipitation asMHP with the production ofMHP agglomerates applied as rawmaterial to furnaces of ferronickel production is a very attractive practice. This work aims to further the technological development of an agglomerated product feasible to hydro-pyro integration. The agglomeration experiments were performed by traditional pelletizing (firing the pellets) and cold bonded pelletizing (aging the pellets by appropriate stocking). Appropriate compositionswere prepared withMHP, additives and binders for each of these routes. A specific study of binder composition was made to find an adequate melting point. The produced pellets were tested to prove their properties by crushing strength tests. The standardization applied to iron ore was followed. The best result of crushing strength was 98.52 daN/pellet. The agglomerates with approved crushing strength for use in electric furnaces were smelted to produce alloys containing nickel; the agglomerates were characterized by scanning electron microscopy. The alloy obtained was metallic ferronickel with sulphide precipitates. Therefore, MHP pellets can be precursors of nickel alloys, which have to be refined to obtain the desirable composition.

Jul 6, 2020

By Viktor Lishchuk, Olof Martinsson, Tobias E. Bauer, Elena Haller

Freely accessible and non-confidential real-life geological data sets from mineral deposits are desirable for the wide range of applications in research and education. However, publicly available statistical data are limited in their number and quality—they contain reduced information about geological, geophysical, geotechnical, chemical, mineralogical, and other relevant properties of deposits. This makes such data insufficient for scientific purposes. However, the amount of geological knowledge obtained for a variety of deposits in the past allows the construction of an idealized synthetic ore body model using analytical approach. Such a model could be used for education purposes and testing basic scientific theories, e.g., visualization of deposit structure; teaching sampling strategies; testing new algorithms for mine planning; or comparing geostatistical modeling methods. This paper presents an analytical approach to simulate volcanic massive sulfide (VMS) deposits and shows how synthetic deposit model can be constructed and further used for studying sampling with drilling and simulating folding and faulting.

Jan 14, 2021

By B. W. Cavender

"World-class manufacturing" (WCM) techniques can be applied in milling operations to substantially improve productivity and reduce costs. Through the use of "just-in-time" and "total quality control" practices, WCM methods establish an environment for continual and rapid improvement in all aspects of production operations, with particular gains in product quality, costs, flexibility, employee involvement, and responsiveness to customers. This paper examines WCM techniques that can be utilized specifically in the mill, and their influence on plant configuration, organization, and scheduling practices; equipment selection and maintenance methods; training; the role of supporting staff; and methods of data collection and analysis.

Jan 1, 1993

By P. K. Sollars, M. A. Alspaugh

In May of 1996, Twentymile Coal Co. began Longwall mining in the Foidel Creek Mine's East Mine District. These Longwall panels are some of the longest in the world (5.48 km/18,000 ft) with very difficult and challenging geometry. The conveyance system is 1,800 mm (72 in) wide, has a 4,500 mtph (5,000 stph) capacity and employs multiple tripper drives. The trippers include traditional powering designs as well as unique regeneration and braking designs. Several components were developed specifically for this application including a mobile tail brake. Control algorithms were carefully developed and tested via computer modeling. A world production record was achieved in the third month of operation and over 1 million tons were mined in June 1997.

Jan 1, 1998