Search Documents

By Mohan Dutt

This paper is concerned with applied platinum resistance thermometry which involves many considerations absent in precision thermometry. The historical development of the Callendar-Van Dusen Equation which describes the resistance- temperature relation of pure platinum is discussed. The advantage of using platinum resistance temperature sensors over thermocouples is described, and the improvements in design and construction of these sensors that have come about in the past few years are discussed. Integral and remote bridges that convert resistance changes into voltage together with signal conditioning techniques and equipment for voltage or current signals are described. Errors encountered in temperature measuring schemes and methods to reduce these errors are summarized.

Jan 1, 1969

By Kenneth K. Landes

Lake stone is a term currently applied to chemical and metallurgical grade limestone or dolomite that is brought down Lakes Michigan and Huron by large cargo vessels, mostly self-unloaders. This stone comes from 5 quarries, all in Michigan and all steel company owned. The volume in 1973 was over 34 million tons. The primary reasons for the large volume are the quantity and quality of the stone available, and the low delivery costs to lower lakes markets. The source rocks are Silurian and Devonian limestones and dolomites of exceptional purity. The regional dip of these formations is 50 to 60 feet per mile southerly toward the lowest point in the Michigan structural basin, which is near the center of the Southern Peninsula. Two of the 5 quarries, both high calcium limestone sources, are on Lake Huron in the northeastern part of the Southern Peninsula. The other three are in the Northern Peninsula; one at the northern end of Lake Michigan, and two on northern Lake Huron. The western quarry is in limestone, the other two in dolomite.

Jan 1, 1975

By C. O. Brawner

A recent advance in slope dewatering-depressurization and stabilization is the use of vacuum assist horizontal drainage. (Brawner and Pakalnis) Horizontal drains have been used for several decades to reduce water pressures in slopes to improve stability. The benefit from vacuum assist arises from an increased hydraulic gradient caused by an induced negative atmospheric pressure. A research program included a laboratory model whereby the effects of vacuum drainage were evaluated. Three case studies are described where the technique has been successful. The first is in a rock slope where flows increased from 0.1 1/min. under gravity drainage up to 1.2 1/min, upon vacuum. The second study involves installation of 17 drains placed at a slightly downward gradient to intercept and de- pressurize aquifers under a major tar sand deposit in Canada. The third study was on a large open pit copper mine in British Columbia where flow increased about 30 per cent.

Jan 1, 1984

By K. Verghese

Neutron capture prompt gamma-ray analysis provides the best method for on-line analysis of the elemental composition of large volumes of bulk material. This paper summarizes the Monte Carlo models which simulate the radiation transport within two such analyzer systems; namely, the borehole configuration and the conveyor belt configuration. The models are useful in the design optimization of the analyzer systems, in minimizing the amount of experimental calibration data for calibrating these analyzers, and in investigating the detection sensitivity for different elements. The computational scheme in these models is made extremely efficient by the use of various powerful variance reduction methods and by efficient data management. Experimental verifications of the two models carried out in the laboratory indicate very good agreement with the Monte Carlo results.

Jan 1, 1984

By Y. Lahaye, O. Martinsson, B. I. Palsson

"Four main and three minor rare-earth-element (REE)-bearing minerals were identified and quantified in the Kiirunavaara apatite iron ore tailings using optical microscopy, an electron probe microanalyzer (EPMA) and a mineral liberation analyzer, and their chemical compositions were analyzed by the EPMA and laser ablation inductively coupled plasmamass spectrometry. REEs are shown to be contained in the minerals apatite, monazite, allanite, titanite, zircon, thorite and synchysite. In zircon, thorite and synchysite, they occurred in only trace amounts and contributed limited amounts to the total REE budget, and these are consequently of minor importance. Monazite occurred as inclusions in apatite and as free particles, 90 percent liberated. Allanite occurred to some degree in mixed grains with magnetite but also as free particles. Monazite mainly reported to the apatite concentrate, while allanite and titanite largely went to the tailings, the latter preferably to those fractions smaller than 38 µm. The amount of titanite in the finest tailings fraction was 2.3 weight percent, containing close to 1 percent REEs, with heavy rare earth elements (HREEs) making up 28 percent of the total REEs. However, a texturally distinct group of titanite grains showed an HREE/REE ratio of up to 67 percent. Furthermore, titanum dioxide analyses indicate that titanite is preferentially released into the tailings from the secondary magnetic separation step in the concentrator. Our data therefore suggest that titanite, occasionally enriched in HREEs, can be extracted from the processing stream and might thus be considered a new source for REEs at Kiirunavaara and similar deposits.IntroductionDeposits of apatite iron ores are the major source for iron in the European Union and are exploited by Luossavaara-Kiirunavaara AB (LKAB) in several mines in the Kiruna-Malmberget area in northern Sweden. Kiirunavaara is the largest of the apatite iron orebodies in Sweden, comprising more than 2 Gt of iron ore with 60 to 68 percent iron (Fe). At the end of 2015, the total accumulated production of crude ore from openpit and underground mining since the start of mining was 1,566 Mt, with ore reserves of 644 Mt grading 46.3 percent Fe (LKAB, 2016). The deposit defines a steeply dipping tabular body, approximately 6 km long and up to 180 m thick, extending at least 1,500 m below the surface. It is situated in the middle part of the Palaeoproterozoic Kiirunavaara Group of volcanic rocks and follows the contact between a thick pile of trachyandesitic lava and overlying pyroclastics (Martinsson, 2004)."

Jan 1, 2017

By David W. Houston

The increasing energy crisis, coupled with stringent environ- mental regulations, has created new demands for high capacity materials handling systems with unit train transporting and continuing surveillance of quality control. Effective and efficient methods of material conveyance are through high speed, high volume conveyor belts with the monitoring of quality through the utilization of automatic sampling. When we speak of high speed, high volume belt discharges we are referring to speed ranges from 600 to 750 FPM and volumes as high as 5500 TPH. To achieve the optimum operating sampling system for high capacity belt discharges, it is imperative that two major design characteristics be investigated and evaluated; namely technical analysis of operating conditions through application of ASTM design criteria and practical experience in the selection of equipment and the design of related components. The task of obtaining a sample of reasonable weight to represent an entire lot presents a number of problems and emphasizes the necessity for using standard sampling procedures.

Jan 1, 1973

By Harrison R. Cooper

Approximately 40 concentrators throughout the world have successfully adopted computer control for flotation circuit operation since 1969. Successful use of flotation control, gaining up to 2% efficiencies, has largely derived from effective employment of on-stream slurry analyzers and integration of key measurement data through digital processors. Requirements for reliable measurement have also led to improved functional reliability in magnetic flow meters, pH, reagent feed, and other key elements. Methods used in computer control of flotation will be reviewed and variations in operating philosophies will be described with reference to the approaches taken to flotation automation.

Jan 1, 1979

By Lynn B. Hales

The Supervisory Computer System at Cities Service copper mine and concentrator at Miami, Arizona was installed at Pinto Valley in the spring of 1975. Design and specification [l] of the digital system was initiated jointly by key plant personnel at Pinto Valley and staff of Cities Service Research and Development Company. The Pinto Valley digital system [2] may be classified as a supervisory control system of hierarchical design. There are three fully independent satellite computers which retrieve and reduce the raw plant data from each of the three main operating areas - the primary crushing plant, the fine crushing plant, and the grinding and flotation plant. While the three satellite computers are core resident systems, the master computer is a disc-based operating system which also interfaces with a computer controlled on-stream x-ray analyzer system. Figure 1 illustrates the basic system configuration [3]. The software systems required to support a large system are quite diverse and vary greatly in function. The philosophy followed in dividing the software into three categories was designed to: 1) fully utilize existing process knowledge of technical staff; 2) delegate certain software tasks to outside sources already skilled and trained in software development; and 3) maintain final control over the design and operation of each system.

Jan 1, 1976

By Miguel Angel Ibarra

This paper describes the results of a digital computer simulation study in which the impact of the proposed truck dispatching on the overall mine productivity was investigated for an operating open pit mine. In the study, the existing operation was first simulated for a one-month period, using both the actual time study data and the computed cycle times. By adjusting certain input parameters to the simulation program, the actual one month production was first duplicated through simulation. Afterwards, the operation was again simulated in a dispatch mode. Comparison of simulation results under the dispatch mode, with the initial base case simulation results, showed a definite improvement in overall productivity with dispatching; i.e., approximately 10% gain for the operation. As expected, the results also showed that the extent of possible improvement did vary with the particular pit configuration being investigated.

Jan 1, 1980

By Thomas A. Simpson

Heretofore, underground coal mines in Alabama have operated under only 60 to 360 meters of cover: however, new mines (at least 5 in the early opening or development stages) will be operating under cover ranging from 600 to 660 meters. With increased rock confining pressures, roof stability problems will become more critical. Initial studies in two 7 ½ -minute quadrangle areas in the Warrior coal basin of Alabama indicate that the orientation of certain lineament and fracture-trace modes mapped from ERTS-1 (Earth Resources Technology Satellite) imagery correlate closely with the strike of joint and fault modes. High altitude (118,000 m) U-2 aircraft data were used to support these findings. In addition, over 50 percent of the normal faults mapped in the study area could be directly correlated with ERTS and U-2 lineaments and fracture traces. These correlations provide clues to the structural development of the Warrior coal basin and may, in turn, be used as a guide to the prediction of roof-stability conditions in advance of mining.

Jan 1, 1975

By James C. Conti

A surface charge sensor has been developed that responds to changes in the double layer properties of colloidal silica during the cationic flotation of silica from taconite ores. Sensor design allows for the measurement of two aspects of the electrical double layer surrounding all solids immersed in ionic solutions. One aspect responds to a flow induced change in the double layer properties of a solid. The other is a function of the chemical composition of the aqueous phase. Evaluation of sensor performance during froth flotation experiments has been encouraging. Process monitoring capabilities are indicated.

Jan 1, 1981

By L. A. Roe

The year 1867 marks the first year of commercial production of phosphate rock in the United States. South Carolina produced almost all of the domestic output of mineral phosphate until phosphate mining began in Florida in 1888. During the period 1868 to 1949 the total marketed production of domestic phosphate rock was about 186 million long tons of which 71.5 percent was produced in Florida, 18 percent in Tennessee and 7 percent in South Carolina (1). From 1949 through 1960, Florida phosphate rock production has ranged Prom 71 to 77 percent of the total domestic production. Since three-fourths of the domestic phosphate production is from the Florida field, and since most of the phosphate from the Tennessee and Western fields is not processed, but used directly as electric furnace burden, this paper will concern itself almost entirely with water requirements for mining and processing ore from Florida. Figure 1 summarizes phosphate rock production for Florida vs. total United States production over the period 1947-1960.

Jan 1, 1962

By James F. McConnell

Federal and State sulfur oxide emission and ambient air quality regulations have been implemented to fulfill the requirements of the Federal Clean Air Act Amendments of 1970. Primary and secondary air quality standards have been established at levels considered necessary to assure the protection of the health and welfare of the public. Standards of performance under this Act have been established to control the rate of sulfur oxide emissions from individual sources so as to protect and to improve the quality of the Nation's air. The new source standards of performance were made rigorous for large coal burning stationary sources. This has had a severe impact on the electric utilities that operate the coal fired steam electric plants which are the largest consumers of the Nation's coal production. States have taken different approaches in State Implementation Plans (SIPS) as approved by the Federal Environmental Protection Agency. Some states, such as Pennsylvania, have chosen to permit moderate SO2 emission rates from existing sources which are not in critical air basins. All are required to meet primary and secondary air quality standards and to limit sulfur oxide emissions from new large stationary sources to a minimum of 1.2 LBS of S02/MMBTU fired. This re- quires a fuel sulfur percentage of about 0.7 for a 12,000 BTU/lb coal. In an effort to develop strategies and technologies to conform to performance standards while continuing and hopefully expanding the utilization of the Nation's coal supply, the electric utilities, the Federal and State regulatory agencies, and other industries and government agencies are considering several alternatives. 1. Natural low sulfur coal 2. Flue gas desulfurization - (FGD) non-regenerative and regenerative 3. Coal gasification 4. Liquefaction and solvent refined coal 5. Fluidized bed combustion 6. Chemical coal cleaning 7. Physical coal cleaning Of these options, only the first and the last can be considered to be widely used in full commercial practice at this time. FGD has certainly demonstrated technical and operating feasibility and is close to being in full commercial practice but it remains to be seen if the large systems under construction are economically and environmentally optimum.

Jan 1, 1975

By W. C. Bagby

The Dee disseminated gold deposit is the northernmost mine in the Carlin gold belt. We analyzed soil samples £ran undisturbed areas overlying the deposit to determine the usefulness of soil geochemistry in identifying ore zones. The depth of sampling ranged from 12 to 14 inches, depending on soil development. The -80 mesh fraction was analyzed by atomic absorption for Au, As, Sb, Hg, and T1 and by semiquantitative spectrographic analysis for Ag. Highly anomalous Au, Kg, As, Ag, and Sb are most closely associated with ore zones whereas T1 is more broadly dispersed. Hg is the only element that identifies deep ore.

Jan 1, 1984

By Bruno A. Fichna

Longwall mining offers low cost potential for coal with high capital investment. As opposed to two shifts-per-day operation in most long- walls, Saarberg Mines in Germany increase utilization of capital by operating their longwalls around the clock. Differentiation between capital and operating costs, corrective maintenance versus preventive maintenance, improved roof conditions, and economical life of equipment was investigated. A surprisingly high degree of improvement was attained. Capital costs at Saarberg longwall coal mines have been reduced through a step-by-step research and trial program. This reduction was particularly influenced by the high performance pilot longwalls at the Ensdorf mine. The following presentation shows data and figures of those longwalls. End results were 40% reduction in capital costs, which could contribute favorably to investment decisions in the coal industry in a supply side economics environment.

Jan 1, 1982

By Éder Domingos Oliveira, Carlos Antonio Morais, Ruberlan Gomes Silva

The objective of this study is to assess the impact of different reagents, such as limestone, lime, magnesium oxide, and sodium hydroxide, in experiments carried out in the single purification step and in two consecutive purification steps by raising the pH of a rare earth sulfuric liquor with the aim to remove or reduce the impurity concentrations in the rare earth sulfuric liquor. The choice for the best purification condition was made based on the minimum loss of rare earth elements (REEs), reagent consumption, and residue generation. The exploratory experiments show that it takes place in the two consecutive purification steps, the first one consists in dosing the limestone pulp until it reaches a pH of 3.5 followed by an addition of a lime pulp reaching a pH of 5.0. Under this condition, the results were a total removal of Fe3+, PO4 3− , and Th4+ ions and a reduction of 99%, 87%, and 37% w/w in the Al3+, UO2 2+, and SO4 2− concentrations, respectively, in the purified rare earth liquor. Furthermore, the lowest REE losses (8.3% w/w) and reagent consumption (4.3 kg/m3 ) and also a low residue generation (7.5 kg/m3 ) were observed in this condition. Despite reaching similar results regarding impurity removal, the experiments done with the addition of limestone, lime, magnesium oxide pulps, and sodium hydroxide solution in the single purification step, where the pH was raised to 5.0, presented higher REE losses (64.9%, 42.5%, 44.8%, and 60.9% w/w, respectively) and a higher residue generation (43.2, 25.1, 11.1, and 13.6 kg/m3 , respectively). This occurred due to the co-precipitation of salts containing rare earth elements in their composition. The experiments conducted with limestone, lime, and MgO resulted in a higher consumption of reagents, while the same result was observed when NaOH was used (4.3 kg/m3 ). In the experiments carried out with the addition of magnesium oxide and sodium hydroxide, the respective purified rare earth liquors presented a high concentration of magnesium, sulfate, or sodium, which could impact the quality of the marketable rare earth salts, whereas the salts obtained under the best condition observed in this study seem to be amenable for use as raw material in an attempt to obtain rare earth products with an acceptable chemical quality.

By C. A. Young

In-situ Fourier transform infrared/internal reflection spectroscopy (FT ?IR/IRS) has been extended to study oleate adsorption at a calcite surface. The birefringent and transmission limitations of calcite were overcome by using an appropriately designed optical setup and a near-infrared (NIR) spectrometer. An adsorption isotherm was determined at pH 9.2 and room temperature. Comparison with the fluorite/oleate adsorption isotherm determined by the same technique indicates that oleate abstraction by calcite can be as much as one order of magnitude larger than that by fluorite. Nevertheless, the hydrophobicity of the fluorite/oleate surface is greater for equivalent adsorption densities as indicated by contact angle measurements and flotation results. The monolayer region has been confirmed to be chemisorbed oleate at both calcite and fluorite surfaces. Furthermore, multichannel laser Raman spectroscopy (MLRS) showed that chemisorbed oleate at the fluorite surface undergoes a double-bond reaction with oxygen to form an epoxide/polyether complex. Such a reaction, however, could not be detected at the calcite surface. These phenomena are discussed in terms of the intrinsic surface properties of the mineral systems as well as the adsorption density and the cross-linking/polymerization reaction of the adsorbed oleate film.

Jan 1, 1993

By Michael F. Werneke

While the use of synthetic polymers for solid/liquid separation is not raw technology (1)(its history goes back to the mid 1950's), its importance has increased dramatically over the past decade. This can be attributed to two major factors. The first of these was a change to mechanized mining (strip mining and continuous underground miners) which resulted in a lower quality (higher reject) preparation plant feed, as well as a higher percentage of smaller size particles in the feed. The second factor has been the greater restrictions imposed by governmental agencies on effluent discharge and solids impoundment, requiring pre-treatment of recirculating water before reuse and treatment of refuse before disposal. Today, synthetic polymers find utility in almost all applications requiring separation of solids from aqueous suspension, including "in-process" as well as waste treatment applications. In spite of the fact that there are over several hundred commercially different flocculants available in the marketplace (2), there are a limited number of chemically different materials available which are useful from a cost/performance standpoint. The potential reasons for using flocculants in a coal preparation plant are summarized in TABLE 1.

Jan 1, 1979

By A. D. Hoagland

There are large areas on all of the continents with environments which are favorable for deposits of zinc and lead of Mississippi Valley type. In the developed countries, these environments have for the most part been quite thoroughly explored for the near surface deposits, and it will be necessary to direct more effort to the search for deeper buried deposits from which much of our future production must come. The difficulties of exploration for deep ore of this type are many and formidable, but the area of permissive environments beneath deep cover is many times as great as the area of the known near surface ore districts. It is a reasonable assumption, therefore, that numerous deposits wait for discovery and development. The finding cost, however, is certain to increase, and it is essential that concepts and techniques of exploration be improved if we are to sustain a reasonably strong productive capability into the 21st century. Exploration for deeply buried deposits requires at the outset relatively large areas of favorable geologic environment. The favorable horizons must be within economic limits of depth for the exploration as well as for the mining techniques which are currently available; and there must be some condition, design or strategy which will assure the explorer a reasonable chance of obtaining maximum benefit from discoveries which he may make.

Jan 1, 1973

By Nathaniel Arbiter

A fully-instrumented driving mechanism has been constructed to study the power, aerating and solid suspension characteristics of several laboratory flotation machines. Machines operating over normal flotation speed ranges give constant power numbers in liquid' systems indicating that they operate under fully baffled turbulent flow conditions. Owing to lack of geometrical scaling, power numbers for different sizes of cells of the same make are different. Even larger differences occur between cells of different manufactures. For a given impeller, varying the tank size did not significantly affect the power consumption. Tank geometry and baffling has a slight effect on power consumption with shrouded impellers. For a given impeller speed, suspension height decreases while power increases with increasing mass of solids in suspension. While power consumption is hardly affected by particle size and clearance between the impeller and tank bottom, the suspension height significantly increases as clearance increases and as particle size decreases. Aeration was found to affect not only power but also the suspension characteristics of the machine. For closely sized particles drastic sedimentation occurred when a critical value of the air flow number was exceeded. The critical air flow number decreased with increasing particle size. This effect was less marked with a wide particle size range. The self-aerating capacity of flotation machines increases with cell size at a given speed for the same impeller-shroud system, but decreases in the presence of frother and solids. Equations have been established for correlating all of the studied variables. Data taken from the literature were also correlated with these equations.

Jan 1, 1968