Search Documents

By G. Davis

It is well known that the anticipated mineral price at the start of a prospective mineral project can have an overwhelming effect on a property's ex ante value. However, possible price movements throughout the life of a project can also have an impact on this value. This paper demonstrates how different potential price paths can affect project value. When considering commodity price projections for mine valuations, it is thus necessary to estimate not only the expected commodity price at the start of the project, but also the manner in which that price is likely to fluctuate throughout the project's life.

Jan 1, 1995

By Patricia Pride, Kurt Bettger, Jack Raymer

"INTRODUCTION The Jefferson Barracks Tunnel is in the final stages of design and is expected to go out to bid in the summer of 2016. The project is located in south St. Louis County along the west bank of the Mississippi River, about 13 km downstream of the St. Louis Gateway Arch. The project consists of a deep sanitary sewer tunnel, a deep pump station and several intakes. The intakes will divert sanitary flows into the tunnel and the tunnel will convey the flows by gravity to the Lemay No. 3 Pump Station, which will pump them up into the Lemay Waste Water Treatment Plant. The tunnel is about 5.4 km long and will be lined with 84-inch (2.1 m) fiberglass pipe. It drops at a gradient of 0.1 percent from south to north and will be bored through strong limestone using a hard-rock tunnel boring machine (TBM). The diameter of the TBM is anticipated to be about 3.4 m. The Owner’s original concept was for a relatively shallow tunnel so as to minimize construction and pumping costs. The preferred alignment ran close to the river, next to the existing force main, which was to be abandoned. Keeping the tunnel close to the force main would reduce the amount of shallow sewer work needed to connect the existing feeder sewers to the new tunnel. Several geotechnical investigations were performed, with shallowly focused geophysics and the borings all going exactly down the conceptual tunnel depth. Limestone bluffs run along the Missouri side of the river. These bluffs are pockmarked by sinkholes and riddled with karst. Large, well-known caves occur both north and south of the alignment. Karst features, including deep crevices and possible caves, were found in those early geotechnical investigations. Many of these features extended well below the level of the Mississippi River and would have been encountered by the tunnel. If a large crevice or cave were encountered, then the inflow of mud and water into the tunnel could have been large and possibly uncontrollable. Something had to be done to mitigate this situation. Pre-excavation grouting was considered, but the program would have been huge and extremely expensive. Using a closed-face TBM with bolted and gasketed lining was also considered, but that too was both risky and extremely expensive. The Owner could have abandoned the tunnel altogether and built a new force main, but that would have brought a whole new set of problems and was undesirable to the Owner. The last option was to move the tunnel away from the karst."

Jan 1, 2016

By B. Morris

This presentation will describe the process by which the Quebrada Blanca (QB) copper project in northern Chile was financed. It will also show how a relatively junior mining company addressed the problems created by its inability to provide its share of the equity funding and the guarantees required by the project lenders. QB is located in the semi-arid Andean highlands of northern Chile, 170 kilometres southeast of the port of Iquique and 30 kilometres west of the border with Bolivia, at an altitude of about 4,300 metres (14,000 feet). Figure 1 depicts the project's location. The QB orebody is a secondarily enriched porphyry copper deposit containing reserves of 85 million metric tons grading 1.3 percent copper. Underlying the enriched zone is a significant primary ore zone containing several hundred million metric tons grading about 0.5 percent copper. In the late seventies and early eighties Falconbridge and its affiliates spent $20-30 million dollars exploring the deposit and conducting feasibility studies. For a variety of reasons they decided not to develop the property which was returned to its owners, Empresa Nacional de Mineria (ENAMI), which is a Chilean state mining corporation. In 1988 ENAMI announced its intention to privatize the property through a public bidding procedure.

Jan 1, 1993

By S. D. Van Nort

The Grasberg porphyry copper-gold deposit of Freeport Indonesia Inc., an 81% owned subsidiary of Freeport-McMoRan Inc., lies within the Ertsberg Mineral District in central Irian Jaya, Indonesia. The Grasberg deposit was discovered during a drilling campaign initiated in early 1988. Production at the open pit Grasberg deposit commenced in December 1989. The Grasberg copper-gold orebody is contained with a young igneous complex of dioritic composition which intrudes limestones of the Tertiary New Guinea Group. Alteration is typical of porphyry copper deposits worldwide except that higher grade primary chalcopyrite with significant gold values is associated with a centrally located zone of strong quartz stockwork.

Jan 1, 1991

By S. K. Kawatra

The fly ash from coal combustion often has a high unburned-carbon content. This can make it unusable as a cement admixture, which is the major fly ash utilization market. As a result, high-carbon fly ashes currently disposed of by landfilling, at sometimes considerable expense. In this paper, the use of froth flotation to remove the unburned carbon from fly ash is described. Three different fly ashes were studied, which had Loss-on-Ignition (LOI) values of 6.79, 6.90, and 11.11 %. It was found that the use of an alkanolamide/oil mixture as a froth-conditioning reagent could greatly reduce the amount of collector needed, by increasing the affinity of the collector for oxidized carbonaceous surfaces. For each of the three fly ashes, froth flotation reduced the LOI of the ash to less than 2% which is well below the ASTM specification of no ' more than 6.0% LOI for Class F fly ash. Increasing carbon content of the ash tended to increase the quantities of reagents needed in flotation.

Jan 1, 1996

By James J. Brady, Kenneth L. Faught, Chadi El Mohtar, Chaoshi Hu

"During construction of a 9.5-ft. diameter sanitary sewer tunnel, the City of Edmonton encountered a large pocket of flowing sand that flooded their TBM and caused significant surface subsidence, stopping further tunneling by the TBM through this zone. A unique collaborative effort ensued between the authors representing the city, consulting engineers and academic researchers to develop the optimal strategy for grouting the problematic soils. The site has a layer of very find sand between 20 and 30 ft. in depth with fines contents ranging from 5% to more than 40%. The collaboration extended from requesting additional site investigation efforts to shipping samples to the UT-Austin laboratories for grout testing plus ground and grouting characterization tests resulting in field recommendations for a full scale ground improvement program. New research information on the grouting of fine sands along with a collaborative framework for the design of in-situ grouting projects are the key topics presented. INTRODUCTION Encountering a large unexpected pocket of flowing sand with an open-faced TBM while excavating a tunnel below the groundwater table is never a good thing. This was certainly true for the City of Edmonton when one of their Lovat TBM’s became inundated by flowing sand while excavating the 9.5-ft. diameter Millwoods Double Barrel Replacement Tunnel in September 2013. However, since the City of Edmonton self-performed this work, a rare situation existed where the site could be investigated objectively, without the prejudice of contending parties selectively influencing how information was gathered and presented, to accurately examine site conditions with a goal of identifying the best remediation measures."

Jan 1, 2016

By Donald M. Ulbrich

Any of you who served in the military remember the admoniton to "get the lead out," In the military environment, where cost wasn't always a factor, "get the lead out" was more often a call for activity of any sort than activity of a particularly productive nature. As a result, when the top sergeant yelled "get the lead out," lots of people started moving.. . usually to get out of his way. Now there's a new cry, ..one that comes not only from the military but from an entire nation threatened with dependence on foreign sources for its energy needs. That cry ...get the coal out, Like the earlier order, it's a call to activity. A signal that the coal reserves of the United States must be tapped so that Project Independence can succeed by 1985, But it's more than a mere call to activity; it's also a call to achieve productivity. ,a call to produce coal both efficiently and acceptably. And that leads us to the key questions of where the coal is going to come from to meet that 1985 goal, and how can it best be mined. Where will the coal come from? There's no doubt much of it must come from surface mining in the West. How can this coal be mined? There are several options available but there is an excellent case to be made for using mining shovels and haul trucks due to their versatility in stripping, loading and reclamation, We'll explore this approach in this talk today.

Jan 1, 1976

By Charles A. Beasley

Increased technical and legislative analysis by all parties of interest could result in more efficientand better directed regulatory legislation in the mining industry. Efforts to forestall or frustrate legislation through massive lobbying and public relations efforts are seldom effective over time and often lead to more stringent and far reaching legislation than necessary. The Federal Coal Mine Health and Safety Act of 1969 is perhaps an outstanding example of such insufficiences; a future example may well be regulatory surface mine legislation. Although a lack of extensive hard data seldom enables rapid or sophisticated analysis early in the legislative process, even preliminary analysis may be sufficient. Simple statistical analyses of available data, assessment of the legislative rationale, and subjective appraisal of other non-quantifiable constraints to improved mine safety. An average of 115 underground fatalities at an exposure frequency rate of 0.67 can be reasonably expected in the immediate future, under existing levels of technology, degree of regulation, and economic conditions. If gross unrefined estimates of 6 preparation plant, 5 surface, and 30 strip mining fatalities are assumed, the total fatality industry level could be expected to approximate 156 Serious professional, economic, and technical constraints within the the industry probably preclude any major decrease of these accident levels within the near future

Jan 1, 1972

By James E. Jones

The coal mining industry is being called upon to vastly increase production in the coming years. Many mining operations will have to prepare an environmental impact report of some kind and all will have to comply with various types of environ- mental regulations. Therefore there is a great need within the industry for access to environmental data, information, and literature. This paper discusses the informational resources available, the current lack of access to these resources, and the Environmental Data, Information and Literature (EDIL) Bank of the Kentucky Institute for Mining and Minerals Research. The bank's major emphasis concerns the environmental, social and economic aspects of producing clean solid, liquid, and gaseous fuels from coal. The data bank promotes information interchange between other related governmental and private projects and the energy development community.

Jan 1, 1976

By Richard O. Rouse

Today, I want to challenge this audience by charging each of you to be a greater manager and superior engineer to manage and engineer our way through the 1980's and profitably overcome all the present and proposed government regulations. May of the present and proposed regulations will tax you and your company's management and engineering to the brink of physical and monetary exhaustion, but I believe we can succeed and coal can be America's answer to her hungry energy needs. To put our 1980's challenge into perspective, I want to give two great challenges we must overcome. First - We must improve on our process of compliance to new government regulations in the technical and equipment end of our industry. The Lord said, "Let There Be Light". MSHA said, "Let there be light in underground coal mines". Since that time, we have lived through an unmanageable and tremendously costly period of compliance.

Jan 1, 1980

By Harry Asche

Tunnels are frequently specified by owners to be designed to a structural code, often a bridge code. In the USA, AASHTO have created a tunnel code, based on structural principles, the AASHTO LRFD Tunnel Design Specification. The Load Resistance Factor Design method (LRFD) described in the AASHTO title is an approximation to the probabilistic design of structures, based on the independence of load and resistance. This methodology is well known to be problematic in geotechnical design, but it is widely used. The paper considers the difficulties of this approach and describes alternative approaches that would result in more appropriate designs for tunnels.

Jun 13, 2021

By C. J. Bise

In August, 1977, the Federal Surface Mining Control and Reclamation Act was signed into law [I]. It stated that: "The Congress finds and declares that because of the diversity in terrain ... and other physical conditions in areas subject to min ing operations, the primary governmental res- ponsibility for developing, authorizing, issuing, and enforcing regulations for-surface mining and reclamation operations subject to the Act should rest with the States." Section 516 of Title V (Control of the Environ mental Impacts of Surface Coal Mining) of the Act deals with the surface effects of underground coal mining operations. "Each permit issued under any approved State or Federal program pursuant to this Act and relating to underground coal mining shall re quire tfieoperator to adopt izeasures consist ent with known technology in order to prevent subsidence, causing material damage, to the extent technologically and economically feasible, maximize mine stability, and main tain the value and reasonable foreseeable use of such surface lands, except in those instances vhere the mining technology used requires planned subsidence in a predictable and controlled manner: Provided, that nothing in this subsection shall be construed to prohibit the standard method of room and pillar mining. "

Jan 1, 1980

By C. Pritchard

John Marks said in his acceptance of the Hartman Award in 2008, “I guess that without the occasional complaint, your mine is probably over-ventilated” (Marks, 2008). Miners are seldom in this situation and spend much of the time trying to find enough air to keep an operation running. With examination, there are usually changes that can be made to increase the efficiency of ventilation systems. Mine ventilation air is a costly commodity, especially by the time it has been heated or cooled and moved to the bottom of the shaft and through the mine airways. Modifications that result in surplus mine ventilation air could bring financial and environmental benefits. Some issues mine operators have needed to address recently are increased airflow requirements to dilute diesel particulates in metal and nonmetal mines, to ventilate reserves that are deeper, hotter, and further away from fans and shafts, and to meet demands from increased production. This paper discusses successful methods to find additional usable air when there is no extra ventilation capacity. Most of the options presented in this paper are useful for metal/ nonmetal operations but some may be applicable to coal as well.

Jan 1, 2009

By S. Phillipson

The Mine Safety and Health Administration’s Roof Control Division (RCD) evaluated the use of Shuttle Radar Topography Mission (SRTM) data to identify fracture traces on Earth’s surface. Results were compared to the analysis method employed by RCD for 30 years, which relies on LANDSAT-TM Band 4. SRTM elevation models are expected to provide a direct representation of bedrock surface, while LANDSAT-TM Band 4 represents reflected near-infrared radiation as an indication of moisture content and is only a proxy for possible structures. Three areas in southwestern Pennsylvania were chosen for ground-truthing lineaments derived from both methods, following a series of desktop comparisons in six areas of the contiguous U.S. Field studies that identified numerous instances in which SRTM lineaments corresponded with joints at the projected location, and were oriented within 10° of joint strike, indicating that those SRTM lineaments represented the structural grain of the area. In some cases, lineaments were associated with individual joint zones. Photo-lineaments derived from the existing LANDSAT-TM methodology appear to offer a higher coincidence with expected trends of joints on a regional scale when performing the desktop comparisons, while field observations indicated that SRTM-derived lineaments had a higher association with individual geologic structures in the case study field area. It appears that both methods can identify the structural grain of an area, and that both tend to identify linear segments of valleys where erosion has preferentially occurred along joint zones or other structures.

Jul 1, 2023

By Gordon B. French

The Occidental Oil Shale mining and retorting system for the production of shale oil has many advantages over the conventional underground mine and surface retort systems. For example only a portion of the oil shale is mined and transported to the outside, where it blends with the existing shale talus found on most of the slopes in the immediate area. The retorted spent shale is retained underground so that it does not become a surface disposal problem. The process consumes only minor amounts of water which is produced in adequate amounts in the retorting to fulfill all mining operations needs without outside supplies. Noise and dust levels are kept to a minimum with most of the facilities located underground. The exception being the generating stations and facilities as required to monitor air and water qualities, and last but not least, more than four times as much oil is pro¬duced from a given acre than from conventional surface processing. With the increased thicknesses as available on the government monopoly area this number could be increased by a substantial amount.

Jan 1, 1975

By Z. Hyder, M. D. Cleason

"INTRODUCTION Mine Ventilation has come a long way over the years. The main purpose of mine ventilation is to keep conditions in the mine safe for the worker so that the mine will be productive and profitable. Technological developments to the mine ventilation system itself and the development of mining techniques have helped improve the safety and productivity of the miners and the mine. Most of the developments to mine ventilation and to safety devices came as the result of serious mining disasters. Another effect of those mining disasters, especially in the late 19th century and after, was legislation to set specific safety standards for mines, especially in the underground coal mines. This paper will focus on the connection between mines disasters and the mine safety legislations promulgated because of those disasters. A BRIEF HISTORY OF MINE SAFETY LEGISLATION Mine legislation has a long history in the U.S. dating back well in the 1800’s. However, mine safety legislation is considerably newer. In 1891, the U.S. Congress passed the very first version of mine safety legislations setting up minimum safety standards. By today’s standards, the 1891 legislation was incredibly basic (7). It took a series of horrific mining disasters for Congress to take action a second time. In 1910, Congress established the Bureau of mines. The role of Bureau developed and changed over next 60 years. In 1995, Congress voted to disband it (27). Initially the Bureau was only charged with investigating and coming up with ways to reduce accidents in coal mines. It was not until 1941, when Congress formally allowed Bureau of Mines’ Inspectors into the mines. In 1947, the Congress enacted and adopted a set of federal safety regulations for the inspectors to follow (1). Finally, in 1952 Congress granted the Bureau of Mines the authority to inspect the mines and to issue citations and/or orders of withdrawals. This act was known as the 1952 Coal Act and the penalties were limited to civil penalties. It would take a couple more iterations of mine safety legislation for monetary and criminal penalties to be introduced (10). Up until 1966, mine safety legislation was directed primarily at underground coal mines and surface coal mines. Congress passed the Federal Metal and Nonmetallic Mine Safety Act of 1966, thus providing a set of standards for all mines to follow (1). The 1952 Coal Act was amended again to be the Federal Coal Mine Health and Safety Act of 1969. This amendment was the beginning of modern mine safety legislation (13). In 1973, Congress created what can be considered the first ‘version’ of the modern day MSHA (Mine Safety and Health Administration). The initial version was the Mining Enforcement and Safety Administrations or MESA. Congress created MESA to act as the enforcement agency, relieving the Bureau of Mines of that responsibility so they could focus on their initial purpose, the development of countries natural resources (14). As mining industry grew, mine safety and health became a greater concern and priority. More efforts were put in legislating the industry. The Federal Mine Safety and Health Act of 1977 provided the platform for today’s mine safety and health legislation. Under the Federal Mine Safety and Health Act of 1977, also known as the Mine Act, MSHA came into being (1)."

Jan 1, 2016

By L. J. Buchanan

The relationship between hydrothermal ore deposits and hot spring systems has received intensive study in recent years, particularly as a consequence of interest in the energy potential of geothermal systems. Base and precious metal deposition in surface pools and at shallow depths in modern geothermal systems has been recorded in numerous publications (1, 2, 3) Theoretical studies of hydrothermal fluid flow at depth, connected to surficial hot springs systems, have been presented by White and others (1), Cathles (2) , Henley and McNabb (3). As a result of these and additional studies, numerous hydrothermal ore deposits are thought to have originated as genetic parts of larger geothermal systems. In particular, it appears that metal precipitation is greatly enhanced in zones of boiling where volatiles and steam are escaping (4). High grade, near surface concentrations of base and precious metals, deposited as a result of partial vaporization of rising fluids, are such a common aspect of modern not spring systems that ore deposition models are becoming based on what may be called a geothermal model. In its most general terms, this model requires an anomalously high thermal gradient which acts as the driving force behind a convecting hydrothermal system. The water may be entirely meteoric or may be In part at least of other origins. The water migrates towards the higher temperature area, becomes heated, and picks up alkalies and metals by dissolving minerals along the fluid path. As water exits to the surface above the heat source, a mass balance requires the incoming hot water to rise to replace the lost water. As the water rises past the elevation where the hydrostatic pressure is insufficient to prevent boiling, then boiling will occur. Depending on the salinity and the temperature of the water, boiling can occur anywhere from great depths to near surface. Boiling results in a loss of volatiles, a pH rise in the fluid phase, cooling of the remaining fluid, a rise in oxygen fugacity, a concentration of salts in the remaining liquid, and precipitation of ore and gangue minerals.

Jan 1, 1980

By T. D. Arnold

The Barrick Bullfrog underground mine was established as an afterthought to the main open pit. As open pit ore dwindles, the underground mining becomes increasingly more important as an ore source, and to the overall economics of the project. This situation is similar to many other mines, and there is a strong move towards underground mining in the United States today. There are inherent problems in starting and operating underground mines in the shadow of any open pit operation, and at the Bullfrog there were several attempts at productive increases that were both successful and unsuccessful.

Jan 1, 1996

By K. W. Grubaugh

The recently enacted federal surface mine law (P.L. 95-87) will increase further the complexity of securing a reclamation permit. This law intensifies the need to present the required reclamation plan in a thorough and comprehensive manner. One plan format, that used in construction performance contracts, offers promise of filling this need. Reasons for using the format of expressed, bilateral, negotiated contracts common to the contruction industry, and the salient aspects of an application which uses this format are reviewed. Advantages of this procedure are seen to be improved mine planning, awareness of the total design job, potential for improved speed of permit acceptance and improved cost control.

Jan 1, 1978

By M. A. Trevits, A. Ozment

"According to the Office of Surface Mining Reclamation and Enforcement, Abandoned Mine Land Inventory System, in 2013 there were 98 underground mine fires in nine states. This is considered to be an underestimate for the actual number of fires nationwide. Many mine fires are started by people burning trash where the coal seam or an abandoned coal mine is close to the surface. Other fire ignition sources include lightning and forest fires. Once ignited, a coal mine fire can easily spread into the remaining coal pillars and mine entries. Once established, the fire creates its own ventilation system supporting further combustion by drawing air down into the workings through unsealed mine shafts, fractures and surface subsidence depressions. As the coal left in the workings from the past mining operations burns, the mine void can collapse, causing subsidence and creating dangerous voids, damaging overlying surface structures and roadways. The products of combustion include smoke and noxious fumes such as carbon monoxide gas. These products are released to the atmosphere through fractures that develop within the ground surface, killing vegetation and creating serious health hazards (Richmond, 2017).Abandoned mine fires, if left uncontrolled, can burn for years and, in fact, one of the most wellknown mine fires in the United States is the mine fire in the Borough of Centralia, PA, that began on May 27, 1962. Reportedly, officials decided to clean up the local landfill for the upcoming Memorial Day holiday by burning the garbage on the site. Unfortunately, the landfill was located on the site of an abandoned strip-pit mine on the edge of the Borough (Dekok, 2009). The strip pit had been left open after being excavated around 1935 and was approximately 23 m (75 ft) wide and 15 m (50 ft) deep. It is believed that the lack of a properly constructed noncombustible shale barrier in the strip pit enabled the fire to spread to adjacent carbonaceous refuse material and then to nearby coal mine workings (PA DEP, 2017). As time went on, the fire grew and spread under the Borough and directly affected the residents despite various efforts to extinguish the fire by the state and federal governments (Fig.1). In 1984, a voluntary program was begun to move residents from their homes. Many accepted buyout offers for their properties and moved elsewhere and after leaving, their homes were demolished. In 1992, the state used eminent domain to take control of all the property within the Borough. In 2013, after years of litigation, the eight remaining residents were allowed to stay for as long as they lived. Today, only a few buildings remain within the Borough (Centralia, PA, 2014). This fire has been burning for more than 55 years."

Jan 5, 2018