Search Documents

By M. Plesha, A. Zubelewicz, K. Connor, T. B. Belytschko, O&apos

INTRODUCTION The Northwestern University Rigid Block Model (NURBM) has been extended to explicitly model dilatant behavior of rock joints. By incorporating dilatancy, the resistance to shear displacement and slip, which previously was limited to simple Coulomb friction, along edge-to- edge contacts is now provided by contact roughness as well as frictional resistance. The explicit formulation is based on concepts presented by Plesha (1985) in which a plasticity-based phenomenological approach was used to model dilatant joint behavior. This approach has been modified to allow for joint closure upon reversal of shear deformation. After presenting a brief description of the new joint constitutive relationship, model behavior will be illustrated with two examples. The first involves a simple two-block model to simulate a cyclic direct shear test of a single joint. The second example involves simulation of a large cavern in a moderately jointed rock mass subjected to cyclic excitation. It will be shown that in- creasing joint roughness increases cavern stability by interlocking of adjacent blocks. JOINT CONSTITUTIVE RELATIONSHIP Within NURBM adjacent two-dimensional rigid blocks interact along their common edge-to-edge contact with contact forces transmitted at the contact midpoint. The contact constitutive relationship was originally restricted to a Coulomb friction yield criterion with no tensile stresses permitted along the smooth contact surfaces. The local coordinate system for any contact is described as shown in Figure 1 with the elastic stresses and displacements related by the linear- elastic constitutive law: [ ] The contact microstructure has been modeled as Patton-type saw-tooth surfaces such as shown in Figure 2. Sliding can be active along the right asperity with angle aR and length lR or along the left asperity with angle a and length lL. In general, aR and aL will difkr as will lR and lL but for purposes of this paper it has been assumed that these angles and lengths are identical. By a simple transformation, the microscopic asperity stresses can be expressed in terms of the macroscopic contact stresses [ ] If Coulomb friction is assumed along the asperity surfaces, the plastic slip condition will be [ ] where µ is the friction coefficient with the convention that compressive stress is negative. When F is negative, the behavior is elastic and when F is zero, slip can ensure. When plastic slipping does occur, it is assumed that the relative tangential and normal displacements between the two contacting rigid blocks are additively composed of recoverable elastic parts and nonrecoverale plastic parts, [ ]

Jan 1, 1986

By R. L. Grayson

An integrated approach to mine management is presented. A model for achieving the level of control of operations critical to surviving in the current market is outlined. The integrated Production and Cost Management System (PRaCaST) is designed to provide mine managers with a reliable, quantitative, decision-assisting system that can be used in formulating timely responses to complex fluctuations in operations. PRacaST consists of a productivity forecast model, sectional bills of materials containing current resources consumption factors, a linear programming scheduling model, and operations analyses that focus on production and cost performances. The system is applied to an underground coal mine.

Jan 1, 1988

By Matias Pentinnen, Wayne Dickinson

Electrowinning is a key process for copper production contributing roughly twenty percent globally and thirty to forty percent of production in the Americas1. Copper grade is assessed largely on deposit smoothness and on level of impurities in the metal. Smoothing aids are essential to create dense, low porosity deposits and guar has long been the material of choice for this purpose. Guar is, however, poorly stable under the strongly acidic electrowinning conditions, underlying ongoing research to identify an effective, acid-tolerant replacement. Current efficiency is also a critical factor in controlling copper production costs and chemical additives should ideally improve current efficiency as well as improving deposit smoothness.

Feb 1, 2025

By I. Pordea

The materials used for the construction of buildings contain natural radionuclides of the U238 and Th232 series and are ? 50% due to land radioactivity. Another component of natural radioactivity is K40, with ? 40%. The presence of these radiopollutants in the final products (i.e. bricks, concrete) due to body irradiation is by two pathways: external irradiation and internal irradiation. External irradiation is due to gamma radiations emitted by Pb214 (RaB) + Bi214 (RaC) from the U238 series, by Ra228 (Mezothoriu I) + Ac228 (Mezothoriu II) + Tl208 (ThC??) from the Th232 series and by the K40 radionuclide. Internal irradiation is due to inhalation of radon (Rn222) and Rn220 (Tn) plus short life descendents (Po, Pb, Bi), radionuclides which are present in concrete. A fraction from radon present in concrete enters into a house leading to internal irradiation by inhalation. In Romania, the maximum concentration of radon allowed for new buildings is 200 Bq/m3.

Jan 1, 2008

By Y. A. Attia, D. K. Sengupta, H. A. Hamza

Increased recycling of waste paper has been emphasized in recent years in both the United States and Canada for environmental and economic reasons. Removal of ink particles from waste paper pulp is therefore necessary. One of the most promising methods for ink removal is froth flotation. This study investigated the feasibility of a simplified flotation scheme and found that about 90% to 92% ink removal can be achieved. Also, a 95% to 97% ink removal is achievable if a hydrophobic polymer is used ahead of the flotation stage. Clean paper pulp recovery was over 90%. The effects of pulping pH, flotation pH and concentrations of flotation and polymeric reagents are discussed in the paper.

Jan 1, 1995

By Glenn Mallory, Margarete Kalin, Ben Romanin

A waste management area of a copper zinc mine which is expected to be generating acid exceeding 1000 years is used as a research facility to develop a passive treatment approach to decommissioning the site. One of the processes proposed to be implemented in a lake with a one million cubic metre volume is biological polishing. To determine the expected performance of the process, model is constructed from experimental data collected in the lake. The model results and the field data represent a weak fit, but the discrepancies are useful indicators of key factors affecting the process, such as iron cycling.

Jan 1, 1995

By John H. Duke

The success of most attempts to evaluate gold orebodies depends largely on the reliability and availability of representative sampling data and the accuracy of geological interpretation. An accurate prediction of the continuity of geology is paramount to a reliable prediction of gold reserves. Many of the problems encountered in gold mine evaluation and planning revolve around the difficulties in interpreting complex geology from sparse drilling data and the eagerness of mine financiers and promoters to start mining in order to derive an early cash flow. Following a program of sampling, geophysics, mapping and geological interpretation, a conceptual orebody model evolves in the minds of those working on the project. It is this model which is used typically in ore reserve computations and mine planning. Computer modelling techniques to represent and evaluate the conceptual model are now available. The main advantages of using computer modelling methods lie in being able to rapidly evaluate, modify and quantify the conceptual orebody model. Ore zones or domains can be recognised and defined both from geology and sampling results. Once these domains are defined as a series of boundaries, they may be modelled as two dimensional grid surfaces or as wire-framed three dimensional geometries, depending on the complexity of the orebody. It is the definition of these domains which provides the sound geological basis for reserves computation. To estimate reserves it is necessary to determine both volume of ore and grade of ore. The ore volume is calculated within each domain as defined by the confining surfaces or wire-frames. The ore

Jan 1, 1987

By S. Meng, R. Jin, W. Hu

In alkaline pulp, galena is depressed by sodium carboxymethyl cellulose (NaCMC), while Cu(II) -activated sphalerite exhibits a high floatability so that satisfactory separation can be achieved. In addition to hydrogen bonding, chemical bonding of NaCMC with galena is confirmed by infrared (IR) spectra; only hydrogen bonding is involved between NaCMC and Cu(II)-activated sphalerite. It is also found that the greater the degree of substitution and polymerimtion of NaCMC, the stronger the depressive effect of NaCMC and that lower stirring speed favors the depression.

Jan 1, 1988

By Annan Cook

Cyprus Metals' Sierrita mine is located in the Pima Mining District, Pima County, Arizona (Fig. 1), which is one of the largest known porphyry copper districts. The ore body is part of a large mineralized system that includes Cyprus' adjoining Esperanza mine. The copper and molybdenum grades being mined at Sierrita make it one of the two lowest grade porphyry copper mines in the world Mineral production from the district was first recorded in 1876. Copper from replacement deposits in carbonate rocks and copper¬-lead-zinc from veins in volcanic rocks were mined from several deposits. However, it was not until 1957 that the district commenced to become a major copper producer with the beginning of production from the Pima mine, which was the first open pit operation. Since that time, seven other open pit mines have come into production. Because of the variable copper prices and high operating costs, not all of the mines are operating today. A map of certain outcrops, plutons, and open pits, as well as older underground mining operations, in the Pima district is shown in Fig. 2.

Jan 1, 1991

By R. F. Davis

The evaluation and selection of coals for producing metallurgical coke is indeed a com- plex process simply because coal is a complex and variable substance which is sensitive to how it is treated from the time it is mined until it is transformed into coke. A review of the the more common evaluation tests made on coal and how the test results are applied in commercial practice. Parameters used to select coal blends for wet and preheated charges should also be of interest.

Jan 1, 1980

By J. C. Motz

The advantages of producing a fine mill feed have been recognized for many years. The extent to which fine crushing can be carried out will vary and depends on the ore characteristics, plant and crusher design. Unfortunately, the ore characteristics are generally beyond our control, so the concentration of effort lies primarily on the plant arrangement, equipment design and operation Where fine crushing should stop and grinding begin is controversial and is influenced greatly by personal opinions and experiences. Often, this break point will be different if consideration is being given to a new plant in comparison to a modest expansion. Most new plant designs employ the largest and most efficient equipment. The modification of existing plants becomes more complex because of the space requirements and the related equipment already in operation. Fine crushing is, of course, a relative term. Obtaining a final crusher product of minus 3/4" is commonplace today and can occasionally be obtained in an open circuit final crushing stage.

Jan 1, 1980

By Victor F. Hollister

Porphyry copper deposits can be categorized into three models for purposes of prospect evaluation: Breccia-pipe, modified Lowell and Guilbert, and diorite models. The modified Lowell and Guilbert model is normally associated with a quartz-bearing intrusive and a potassic, phyllic, argillic, and propylitic alteration sequence. Variations can occur in the alteration zones of this model that range from orthoclase-rich (Kalamazoo, Silver Bell, and Mineral Park) to ortho- clase-deficient (Petaquilla and Bougainville) potassic zones. The unifying features of the model are the presence of a phyllic zone and a quartz-bearing intrusion. The breccia-pipe model (Toquepala) is characterized by structure and alteration related to or controlled by breccia. Where tourmaline occurs in the breccia, the identity of the model is usually clear. However, if tourmaline is not commonly developed in the breccia (La Caridad), the deposit can be misidentified as to model. Porphyry copper deposits associated with quartz-deficient intrusives, whether these are calc-alkalic diorites or alkalic plutons, are characterized by alteration suites distinct from those of the modified Lowell and Guilbert model. These have been generalized as diorite model porphyry deposits. Because alteration and mineralogical development in diorite model deposits is distinct from that of the modified Lowell and Guilbert, ore guides and exploration tactics differ for the two models. The reprint that follows describing the three prospecting models summarizes their features. It is to be emphasized that these are models used in exploration for specific deposit types and are not genetic, tectonic, or geographic models. Porphyry copper deposits can be metamorphosed. Gibralter is an example of a Lowell and Guilbert model deposit that has undergone regional metamorphism.

Jan 1, 1991

By R. D. Auten

This paper is primarily a report on the process of using oolitic aragonite, as received from Marconi& Ocean Industries, Ltd. without further processing, for a major portion of the raw feed to a rotary kiln producing cement clinker. Oolitic aragonite is a high purity calcium carbonate material, dust free, with the appearance of a course, white sand. It is farmed when under the right conditions of temperature ocean currents, and ocean floor topography. The calcium carbonate will precipitate into small spherical particles on the ocean floor. These oceanic conditions are correct to cause precipitation of the calcium carbonate near Ocean Cay in the Bahama Island chain. The present growing deposit near Ocean Cay is in the billions of tons and is mined by a relatively shallow-operation hydraulic dredge. The aragonite thus formed is en orthorhombic crystaline form of calcium carbonate with a specific gravity of approximately 2.9. At a temperature of 505°C. (940F), the aragonite converts to the hexagonal crystal of calcite with a specific gravity of 2.6 to 2.7. This change in specific gravity weakens the structure of the particles but the individual pieces are still fairly hard. When the material is then calcined at 900°C (1650°F), the particles retain their shape but become soft and will break up under finger pressure.

Jan 1, 1978

By R. Tanaskovic

The objective of study of climatic conditions in underground mines is to create a working environment suitable for normal development of operations. Disregarding the fact that the development of equipment and technology, especially during the past decade, made the work in underground mines much easier, it is observed, according to the number of professional publications, that increasing attention is devoted to the study of climatic operating conditions in mines of many countries. This indicates that the climatic operating conditions are closely connected with productivity, and in turn with mine production profitability, in addition to the protection of manpower health and working capabilities. Usually, the concept of unfavourable climatic conditions of operation implies increased mine air temperature and humidity and low air flow rate, resulting in impeded heat exhange between human organism and working environment. As known, above phenomena are present in deep underground mines where the heat problem exceeds the-problems related to other features of natural conditions of mining. On the contrary, unsuitability of climatic operating conditions in mines with shallower mining depths is manifested by inadequate heat, particularly during the cold winter period. The two stated aspects of unsuitable climatic operating conditions are not solvable only by mine ventilation, so the former case requires cooling and the later one heating of the air used to ventilate the pit, or part there of where the phenomena are manifested. Study of climatic operating conditions in mines is, due to the number of factors involved, a complex and time consuming task, and this was, among others, one of the reasons for inadequate study of these problems in many mines. However, it is evident that further development of mine production imposes the need to make the climatic operating conditions in mines similar to those existing in other activities, where increasing attention is being devoted to the improvement of these conditions. Development of mining industry in Yugoslavia, particularly over the past decades, caused several of our mines to approach mining depths where the heat regime has a major influence on climatic operating conditions. This imposed the need to determine and investigate heat regime parameters, especially those that cause unsuitable operating conditions. The results of such investigations in the case of the deep part of Lead and Zinc Mine "Trepca" - Stari Trg are briefly reported in this paper.

Jan 1, 1980

By Y. J. Wang

Optimal sizing of a ventilation shaft is a classical subject in mine ventilation economics.. The shaft size is optimized by minimizing the sum of shaft-construction and ventilation-power costs, or owning and operating costs. The length and air quantity of the shaft are held constant, and the location of the shaft, affecting its depth, and construction and ventilation power costs, is not considered (Hartman, 1961; Lambrechts, 1974; Wang et al., 1978). This paper proposes an approach by which the location and size for a new pair of shafts (intake and return shafts) are optimized for a coal-mine ventilation network. Specifically, the problem is to determine the location and size for a new pair of shafts, and the distribution of air between the new and old shafts so that the combined cost of shaft construction and ventilation power is minimized. The shaft length or depth corresponds to the height of overburden at any shaft location. To simplify the problem, the shaft locations will be limited to the line along the main or submain entries, and the connection entries at the shaft bottom neglected. In order to calculate the ventilation-power cost, the air power of the system should be determined. This in turn requires the calculations of the air quantity and pressure of each fan in the network, satisfying Kirchhoff's laws and Atkinson equation. After obtaining the air power, the cost calculation is straightforward. In the following, we shall assume that the resistances of all airways, and the quantity for each mining section, which is controlled by adjusting the air regulator, are all known. The resistances for the shafts are determined from the estimated friction factors, and shaft dimensions and lengths. Furthermore, it will be assumed that the fans can be selected to meet the duties called for by any network solutions.

Jan 1, 1982

By S. Chander

The effect of pretreatment potential on the response of a gold electrode for Eh measurements in sulfide solutions was examined in terms of measured Eh values and electrode response time. The electrode response time is defined as the time required for the electrode to reach a steady-state value. The relationship between measured Eh values and the hydrosulfide ion concentration is established. The effect of pH, the reversibility of the gold electrode in the sulfide solutions, and the reproducibility of measurements are also investigated. A mixed potential theory is proposed to explain the observations.

Jan 1, 1989

By Derek J. McCracken, William G. Holroyd

Emery is a rock that at one time held a large share of the abrasives market. The introduction of synthetic abrasives, however has forced it to settle for only certain niches in the marketplace. This loss of market share is due mainly to the higher amounts of impurities and weaker internal structure that naturally occurring minerals have compared to manmade materials. The use of rocks and minerals as abrasives dates back to early man, who used flint, quartz, and other natural materials to fabricate various tools. During the 19th century, with the Industrial Revolution imminent, the character of the abrasives industry was changed forever as synthetics were introduced. Frank B. Norton is credited with producing the first manmade abrasive when, in 1855, he manufactured a vitrified grinding wheel using emery grit and clay. Before Norton's accomplishment emery had been the only commercially available abrasive. The latter part of the 20th century has seen synthetics capture an increasing share of the abrasives market from natural materials. The term emery is believed to have been derived from the words emeri (French), smeriglio (Italian), and smiris (Greek). The term corundum, for the principal mineral of emery, seems to have originated from kauruntaka, the Indian name for the mineral. GEOLOGY Emery is a gray to black, granular rock comprised of various minerals including corundum (A1,0,), an iron-bearing mineral (usually magnetite-Fe,O,, hematite-Fe,O,, or hercynite- FeAI,O,), and several trace impurities such as mullite, titania, silica, and magnesia. The hardness of emery normally ranges between 7 and 9 on the Mohs scale, depending on its mineral com- position and level of impurities. Corundum, the hardest mineral in emery, typically has a hardness of 9. The specific gravity of emery ranges from 3.2 to 4.5, also depending on mineral composition and purity. The crystallography of each mineral contained in emery differs somewhat. Corundum exhibits an hexagonal crystal structure, whereas magnetite forms within the isometric system, frequently as octahedral crystals. Hercynite, an iron spinel, is also isometric. Hematite has an hexagonal structure but often is found as botryoidal and reniform masses. Principal deposits of commerical emery are found in the United States, Turkey, and Greece. In the United States two emery producers in the Westchester County-Peekskill area and one in the Cortlandt County area of New York closed their mines in the late 1980s. Commercial production in the United States now comes only from the western Cascade Range in Oregon. The emery in New York has a typical A1,0, content of 41.5%. Most of the rock is not true emery because it contains a mixture of spinel and magnetite but very little corundum. The deposits are of Late Ordovician-Early Silurian age and consist of veins in which emery is mixed with olivine, pyroxene, and hornblende. The veins evidently were formed by contact metamorphism and are surrounded by Precambrian schists that contain mica, sillimanite, cordierite, garnet, and quartz. The deposits in Oregon were formed during Miocene time by the contact metamorphism of ferrunginous bauxite by intrusive lamprophyric dikes and plugs. Emery is found in thin layers bordering these tabular dikes, which are usually oriented perpendicular to bedding, and in "surficial placer deposits. The emery deposits in Turkey occur as small, massive, lens- shaped bodies and as surficial placers. They are believed to have formed during Permian and Triassic times. In Greece the principal site of emery production is at Cape Emeri on the Island of Naxos. These deposits consist of lenticular masses of emery surrounded by marble. They originated during Mesozoic time, evidently by metasomatic replacement. Smaller deposits on several other Aegean islands were formed by the metamorphism of bauxite or other alumina-rich materials.

Jan 1, 1994

By B. Mishra, A. Staley, D. Kirkpatrick

The major waste product of the alkaline extraction of alumina from bauxite (Bayer Process) is known as red mud. Approximately one ton of red mud is produced for every two tons of bauxite mined. The red mud produced from Jamaican bauxite is rich in hematite, alumina and titanium oxide. It has been shown that more than 90% (by weight) alumina can be recovered from red mud by soda ash sintering and caustic leaching. Hematite can be carbothermically reduced with a degree of metallization of more than 94%, resulting in attempts, for magnetic separation. These separations are desirable because there are no waste products generated. Consequently, there is an opportunity for complete utilization of the waste material. Conversely, the preseparated material could be charged through the tuyeres in an iron blast furnace, or it could be smelted to produce pig iron. If smelted, the concentration of titanium oxide in the slag would be high enough to justify its recovery by an established acid-leach process. This paper describes the results of alumina recovery and the plans for titanium oxide recovery from red-mud. In addition, the situation of ongoing efforts in iron extraction, particularly, the method of magnetic separation of the reduced material. The problems associated with the use of reduced red mud as an alternative to direct-reduced iron (DRI) is also discussed. A critical assessment of the recovery sequence chosen for the products is described based on economics. Key words: Red mud, Waste product utilization, Alumina recovery, Titanium oxide, Iron

Jan 1, 2003

By W. A. Rickelton, A. J. Robertson

The ability of triisobutylphosphine sulfides to selectively recover silver from acidic sulfate solutions containing zinc and copper is described. Selectivity is explained in terms of the concept of hard and son Lewis acids and bases. Silver is stripped from the solvent using a novel strip feed (thiosulfate salt), and the recovery of metallic silver from the strip liquor by electrolysis or cementation is suggested. The high selectivity of extraction for silver and the utility of the stripping reagent are demonstrated in continuous, countercurrent, mini-plant tests. Important reagent properties, such as hydrolytic stability and low aqueous solubility, are discussed.

Jan 1, 1988

By Kenneth R. Dickson, I. Michael Gowring, Gary M. Davey

The Kemano Power Tunnel is currently being constructed by a joint venture of Atkinson, Kiewit, and Commonwealth. The 5.73 m diameter, 16.1 km long tunnel is part of the Kemano Completion Project in British Columbia, Canada which is being developed by Alcan Smelters and Chemicals Limited. The discussion includes the refurbishment and development of Robbins TBM 189-229 previously used at Calaveras (RETC Proceedings, 1987), the logistics of conducting a tunneling operation in a remote area with adverse weather conditions, in addition to a description of the work and the performance details in the various geological conditions encountered to date.

Jan 1, 1991