Search Documents

By A. Jolly, A. R. Kumar, T. Novak

"Coal dust in an underground mining environment has always been a health and safety issue, especially with longwall faces. Efforts to integrate a flooded bed scrubber within a longwall shearer are underway at the University of Kentucky (UK) in order to reduce worker exposure. Small scale physical modeling, along with numerical modeling and full-scale experimentation, are engineering tools being used by the authors for simulating operating conditions underground. Recent advances in affordable 3D printers offer a means for fabricating accurate, scale models for obtaining timely insights prior to building large, expensive test setups. Comparing scale-model results with those of numerical modeling, such as computational fluid dynamics (CFD), lends guidance and confidence in a proposed design. This paper discusses the small scale physical modeling of a longwall shearer with an incorporated flooded-bed dust scrubber in its operating environment. A tracer gas was used in the model in lieu of dust to measure dust-capture efficiency. Results obtained from the physical model are presented and compared with those of CFD model. The small scale model and the CFD results demonstrate good agreement. Dust capture results show the usefulness of the approach in advance of actual design implementation. INTRODUCTION Dust generation is an undesirable, but innate, byproduct of all mining processes. It is particularly problematic in underground coal mining, where coal dust poses potential hazards from two fronts – health and safety. Coal workers’ pneumoconiosis (CWP), commonly referred to as black lung, is a chronic lung disease that results from the long-term overexposure to respirable coal dust. Although the prevalence of CWP has steadily and significantly declined over the three decades following the Federal Coal Mine Health and Safety Act of 1969, a study by the National Institute for Occupational Safety and Health (NIOSH, 2008) indicates that significant health hazards associated with respirable dust still exist within the coal mining industry. In addition to being a health hazard, coal dust can also create a potentially catastrophic safety hazard. Dust that is not captured or removed at its source is suspended and transported throughout a mine by the ventilation airstream. This float dust is subsequently deposited on all mine surfaces along its travel path. Without adequate application of rock dust to these surfaces, forces from a localized methane ignition can reintroduce settled coal dust into the airstream creating an explosive mixture. Therefore, capturing and removing coal dust at its source mitigates the probability of two major hazards that continue to plague the mining industry."

Jan 1, 2016

Historian and storyteller, Duane Smith, will be the keynote speaker at the National Mining Hall of Fame's 10th anniversary induction banquet on Saturday, Sept. 6,1997 in the Museum Convention Center at Leadville, CO.Smith is a professor of history and southwest studies at Fort Lewis College in Durango, CO. He is also an award-winning author of 28 books about the West and mining. Hall of Fame Board Chairman Richard Moolick said the induction banquet event will mark the National Mining Hall of Fame and Museum's 10th anniversary in its Leadville facility, a century-old Victorian schoolhouse. Karl Elers, chairman of Battle Mountain Gold in Houston, TX, will be the master of ceremonies. He is a member of the National Mining Hall of Fame and Museum's board of directors. The six inductees into the National Mining Hall of Fame will be enshrined by Thomas Falkie, president of Berwind Natural Resources of Philadelphia, PA. He is also chairman of the Mining Hall's board of governors. The six inductees will join 132 mining greats who were previously honored. The black-tie (optional) banquet will be highlighted this year by guests who prefer to don 1890s dress for the occasion in the old silver-mining boomtown. A cocktail reception and open house will precede the banquet, with tours of the district and special events to follow on Sun- day, Sept. 7.

Jan 1, 1997

By E. Bane Kroeger

Plane failure in rock and soil slopes is usually caused by the intersection of a discontinuity plane with a slope face. Normally, these discontinuities are weaker than the surrounding intact rock and provide a surface along which movement can occur. The discontinuities are typically analyzed to determine the stability of a particular slope. One problem that arises when evaluating the stability of a planar feature is that the method for planar analysis is two-dimensional and has difficulty dealing with planes that are oblique to the slope face. Several researchers have stated in the past that planar failures are a special case of wedge failure. Wedge failures occur when two planar discontinuities intersect in an unfavorable manner. Sliding can occur along the intersection of the planes. Wedge failures are very common in rock slopes and can often be problematic. Wedge stability analysis methods are typically three-dimensional and can analyze planar features that are very oblique to the slope face. Wedge failure analysis can also be used to determine the stability of planar features with good success. One advantage to using wedge analysis over plane analysis is that a tension crack can be both non-vertical and oblique to the slope face in the wedge analysis. This allows the engineer to more closely match field conditions. It also negates the need for the engineer to have two separate software packages to analyze a single slope, saving both time and money.

Jan 1, 2002

By Roe-Hoan Yoon

INTRODUCTION In 1960, coal accounted for 49% of the world energy consumption, an amount that was reduced to 29% in 1973 because of the availability of cheap oil. At that time, it seemed that oil would remain available for a long time in unlimited quantities. However, this situation changed drastically in 1973/74 when a series of closely spaced price increases from $3 per to $12 per bbl by mid-1974 hit both industrialized and developing countries. Another sharp price increase in 1979/80 to the $34 to $38 per bbl level also hit the world economy hard and, at the same time, set in motion powerful technology development forces for increased coal utilization. At this point, the price of coal was approximately $1.50 per MM Btu, while that of oil approached $6.00 per MM Btu. This huge price differential offered an incentive for developing new coal technologies including liquefaction, gasification, fluidized bed combustion, coal-water mixture (CWM), etc. The CWM technology was of particular interest to the utility industry, which consumes more than 80% of the coal mined in the US for power generation. In this technology, a powdered coal is mixed with water to produce a stable slurry that can be stored for an extended period of time without settling and is readily pumpable. Various reagents in the amount of approximately 1% by weight of the coal are added to inhibit sedimentation during storage and to reduce the viscosity for atomization in burners. The coal loading is in the range of 50 to 80% solids, depending on the particle size and its distribution. With very fine particles, it is difficult to increase the coal loading above 50%, and a binomial distribution helps increase the coal loading. The presence of water consumes a relatively small amount of the heating value of the coal during combustion; for a coal-water slurry containing 30% water, less than 5% of the calorific value of coal is usually consumed due to evaporation. The major advantage of burning coal as a slurry is that many of the oil-burning furnaces can be converted to coal-burning with a minimum retrofit cost. Considering the substantial price margin between coal and oil, the pay- back period for retrofit costs can be relatively short. Nevertheless, the retrofit cost can be further reduced if low-ash coals are used as feedstocks for CWM; there will be savings in the capital cost of installing bag filters or electrostatic precipitators that are designed to remove the ash from the combustion gases. Furthermore, the use of low-ash coals can minimize derating of boilers because the velocity of the combustion gases can be maximized without creating erosion

Jan 1, 1991

By G. Danko

MULTIFLUX, a new thermal, hydrologic, and airflow model and software is being developed to solve the flow of heat, moisture, and air in and around an underground opening. MULTIFLUX couples two distinct domains that are solved separately first and re-coupled as an iterative task: (1) the rockmass, and (2) the airway. The airway is solved with a lumped-parameter Computational Fluid Dynamic (CFD) module which is an embedded part of the MULTIFLUX code. The CFD model includes convection, conduction, and radiation for heat, as well as convection and diffusion for moisture transport in an air-filled opening. The CFD model also solves for the airflow field. The surrounding rockmass model may be from any analytical solution, or from a complex thermal-hydrologic numerical model such as NUFT or TOUGH2. The rockmass model is interfaced to MULTIFLUX using a novel technique called Numerical Transport Code Functionalization (NTCF). The method provides fast convergence on a personal computer platform. The paper reports the results of MULTIFLUX simulations for a mine drift, comparing calculations with a known mine climate software, CLIMSIM, and with measured data. Through this validation example, the performance of MULTIFLUX is demonstrated. The results show excellent agreement due to the use of realistic modeling assumptions and boundary conditions.

Jan 1, 2009

By J. Kulczycka

The concept of sustainable development is be-coming present in the policies of increasing number of industries and governments. The complexity affects not only production aspects, but has also special relevance for environmental decision making. Not only producers are re-evaluating the services they expect from the environment and concomitantly increasing their willingness to sacrifice other consumption in favour of enhanced environmental services, but the character of environmental issues is becoming more complex as well. Incomplete information, uncertainty, system wide change, trans-frontier impacts, current causes that have far reaching future effects, irreversibility, and possibilities of catastrophic change all complicate the environmental decision making process. Non-ferrous metals production, due to a relatively low level of metals content in ore, results in generating huge amounts of tailings, exceeding usually 90% of the mine output. They must be stored in special facilities, which have the significant impact on the environment both during tailing management facilities (TMF) operation and after their closure. One of the most essential impacts of operating and closed TMFs is their eolic activity, displaying in worsening air quality, aero-sanitary conditions in the neigh-boring villages and contamination of soils close to the facility by heavy metals.

Jan 1, 2005

By H. Richard Eisenbeis, Donna M. Watkins

Many technical professionals (tp)* desire to occupy upper level management positions. But career paths for most scientists and engineers do not extend beyond their specific disciplines. This is unfortunate. Our technical frontiers are expanding so rapdily that it is difficult, if not impossible, to make sound top management decisions without understanding the technical complexities involved. Technical professionals often are not considered for upper level management positions because they lack the managerial and interpersonal skills necessary to become successful administrators. You've heard this before, but a key component of these skills is the ability to communicate. Technical professionals are often unable to communicate as well as they should with nontechnical professionals and nonprofessionals within the organizations that employ them. Communication is important for managerial success Communication is the network of interactions whereby knowledge and understanding are conveyed from one social set to another (Flippo and Munsinger, 1982). In order to be successful, managers must not only be "good" communicators, they must be "effective" communicators as well. Good communication occurs when managers are able to formulate and transmit their messages in such a way that they are received and understood. Effective communication goes one step further: It occurs when recipients accept messages as legitimate and respond to these messages in the manner desired. Before promotion into upper level positions, managers must have developed organizational skills (planning, decision making, organizing, and controlling) and interpersonal skills (directing, influencing, and motivating). Applying these skills effectively is difficult without a highly refined ability to communicate. Effective communication, then, is basic to managerial success. Nowhere, perhaps, has the importance of being able to communicate effectively been emphasized more than in Mintzberg's landmark study of managerial roles (Mintzberg, 1973). Mintzberg's results indicate that executives typically averaged 36 written and 16 verbal contacts a day. These contacts were both important and trivial. They generally occurred in a random manner. Time spent on each varied. Scheduled meetings averaged over an hour. Desk work, telephone calls, and unscheduled meetings required an average of 15 minutes or less. Why technical professionals have difficulty communicating Three reasons why technical professionals do not communicate well are: • The work motivational patterns and personal attitudes of technical professionals are not conducive to effective communication. • Students in technical professions are not encouraged by educational institutions to develop their communication skills. • Organizations do not insist that all technical professionals be able to communicate in the language of business. The work motivational patterns of most technical professionals are indicative of internals and high achievers (Hunt, Salisbury, and Whittington, 1968). As internals, they believe they control their own destinies. As high achievers, they believe that task accomplishment is a primary indicator of success. To ensure a task is completed in the manner desired, tp's attempt to structure and define work situations so they alone are responsible for results. TPs consider the task accomplished when they, and perhaps other tp's, are satisfied with the results. From the tp's perspective, the task may have been completed. From a communication standpoint, two other factors may apply. First, solving the problem required very little interaction (and thus, communication) with others. Second, the tp's, considering the task accomplished, have little concern for how their "technical" answers will be translated to nontechnical persons needing

Jan 8, 1987

By Thomas E. Krakowski

INTRODUCTION This paper presents a method of calculation of internal moments and thrusts in tunnel liners of any material. The method is intended for hand calculation, but as it is numerical in nature it can be programmed for use in computers. The information required for design or analysis is presumed active internal and external pressures, the effective moment of inertia and cross-sectional area of the tunnel liner, the liner's modulus of elasticity, and the coefficient of subgrade reaction of the material surrounding the tunnel. Starting with active external and internal pressures and following the procedure described herein using the structural properties of the liner and surrounding medium, external passive reactions and internal moments and thrusts are calculated. The method is intended for use by design engineers. GENERAL Experience has shown that flexible tunnel liners have less internal bending stresses than those calculated using classical structural theory applied to free-standing arches. In fact, liners which are very flexible in relation to the surrounding soil or rock have virtually no bending moments when compared to free-standing arches supporting equal active loads. In order for this phenomenon to occur, the original active pressure diagram must be "modified" by additional external reactions (passive pressures) from the surrounding material, so that the thrust line within the lining follows the centroid of the tunnel arch more closely than that of a similar free-standing arch. These passive pressures are reactions developed through outward deflection of the tunnel liner. Thus, the outward moving portions of a

Jan 1, 1979

By R. C. Freas

Limestone is a basic raw material in the production of cement, lime, a wide variety of industrial products, and a significant percentage of the crushed stone produced in the United States annually. It is used in fluxes, glass making, mineral fillers, environmental applications such as flue gas desulphurization and water treatment, soil conditioners, animal feeds, and as a construction aggregate. This presentation provides an overview of limestone distribution in the United States, it’s production, the variety of products produced, and a brief review of the primary uses for limestone.

Jan 1, 2006

By Fernando Concha, Arturo Barrientos, María Cristina Bustos

Manufacturers referred to high capacity thickening as a filtration operation rather than thickening in spite of the fact that it is performed in thickeners and that conventional thickeners can be operated as high capacity thickeners by changing the feeding level and operate it in a different manner. In this work we derive a phenomenological model for high capacity thickening based on mass and momentum balances. The difference with a conventional thickening is the presence of a surface source within the variable domain. The model can be used to design, simulate and to develop control strategies.

Jan 1, 1995

By G. V. Basham

"Environmental audit" is a phrase that can raise the blood pressure of otherwise cool and calm corporate personnel. There is widespread concern that any organized effort to find environmental problems will do so and may result in the imposition of substantial liability against the business that engages in such activities. However, such audits can reduce rather than enhance possible liability. Relevant issues include: the role of the attorney in the process, liability risks associated with environmental audits, steps to maximize confidentiality of audit results, reporting requirements and use of audit results in a proactive manner.

Jan 1, 1995

By R. W. Smith

Though generally rather non-selective in nature long chain collectors nevertheless function in different ways in accordance with their own particular physical characteristics. Altering various parts of their structures such as chain length, type of chain, etc. can therefore substantially alter the adsorptive behavior of the collectors in a set environment. The effect of such structural differences of the collectors on physical parameters such as solubility, critical micelle concentration, acid or base strength, tendency to be expelled from the aqueous phase is discussed, as is also the effect of these parameters on flotation behavior.

Jan 1, 1989

By Arthur J. Borst, Joseph P. Gildner

In a recent National survey, Seattle topped the list for having the worst daily traffic congestion. To address this problem, Sound Transit is planning to build 40km (24 miles) of light rail, including ten kilometers (six miles) of twin tunnels with four subway stations 40 m (130 ft.) to 65 m (210 ft.) deep. The overall schedule is very aggressive and Sound Transit is preparing four separate heavy civil construction contracts for simultaneous underground construction. Three of these contracts are being considered for design-build. Final design will start in March2000 and all underground construction must be completed by the end of 2005.

Jan 1, 1999

By J. Cheung, H. Rabia

The traditional methods for predicting mine air temperatures are based on steady state heat transfer models as developed by Voss (1969) and Starfield (1983). These models are useful in providing approximate predictions of air temperatures in trunk and gate roadways. More complex models are required to provide predictions along faces. In practice, the heat flow in underground mines is of transient nature and recent observations in some British Coal mines show temperature variations of up to 5°C during a working week at any one point. In addition, the recent introduction of district recirculation of mine air in British mines requires a more precise prediction of air temperatures during start up of the system or during breakdown. A transient heat transfer theory based on the work of Jordon is presented. The method lends itself easily to computers due to the large number of calculations involved. The proposed transient model is validated using actual temperature data collected in roadways in Wearmouth Colliery in the North East of England. The transient results are compared with the steady state predictions of Voss (1969). Finally, predictions of air temperature in roadways for a recirculation system will be made using both the transient and steady state models. Temperature predictions along faces will be made using a separate model.

Jan 1, 1989

By E. Piesch, M. Urban, G. M. Hassib

INTRODUCTION In radon dosimetry diffusion chambers with passive [a]-detectors are now in current use to investigate the long-term accumulated indoor exposure of radon and daughters. For the diffusion chamber developed at Karlsruhe the electrochemical etching technique (ECE) was applied to reveal [a]-particles in polycarbonate plastic detectors. Compared to conventional etching, the main advantages of the ECE are the large track diameter, simple track counting in a single field of about 1 cm2, stability of the latent tracks to humidity and temperature and ability for a long-term accumulation up to 1 year. The electrochemical etching system was designed to etch in one run about 101 foils by using a 200 W high voltage generator. The commercial available radon dosimeter system is applied for a country wide program of measuring radon in dwellings. Because of an increasing interest of radon monitoring in mines, environmental monitoring and personnel dosimetry the properties of several track etch detectors have been studied. In the comparative study, Makrofol E, LR 115 and CR 39 were used in the diffusion chamber to investigate the etching techniques, the relative efficiency, the measurable [a]-energy range, and the counting statistic for the measurement of radon concentration. THE KARLSRUHE DIFFUSION CHAMBER The design of the Karlsruhe diffusion chamber is presented in Fig. 1. The upper part of the chamber is closed by a fibreglass filter to separate radon from aerosols, heavy dust particles and radon decay products. Inside the diffusion chamber [a]-particles from radon and daughters are detected by two passive radon detectors, one on the bottom of the chamber and the other in front of the filter. With the fibreglass filter applied the diffusion time is about 1 minute for radon. Therefore, also short-term variations in the radon concentration are recorded by the track detector. Mainly because of the short halflife of thoron (56 s) only about 7 % of the thoron concentration is expected in the diffusion chamber. Radon monitoring provides the estimation of the long-term accumulated mean value of the radon concentration with a lowest detectable concentration of 0.1 pCi/1 after 3 months accumulation by using polycarbonate track etch detectors, an electrochemical etching technique and track counting in a single field of 1 cm2. The diffusion chamber was optimized for the polycarbonate track detector with respect to chamber geometry and detector position [1]. Table 1 presents data for 3 different diffusion chamber designs. The radon sensitivity of the diffusion chamber depends on the [a]-energy discrimination and the angular response of the [a]-track detector. The difference between foil No 2 and foil No 1 can be explained by an additional plate-out effect of radon daughters on foil No 3. The high sensitivity of foil No 3 compared to that of foil No 2 is caused by an increase of the effective volume and the effective area for [a]-particle from radon and from plated-out decay products, respectively. Additional experiments have been performed in order to investigate the electrostatic properties of the plastic material and the properties of the diffusion filter [1]. The properties of bare a-detectors were compared with those inside the diffusion chamber. In contrast to laboratory results, dust particles deposited on the detector surface or in the environment of the detector obviously affect the reproducibility of the bare detector significantly. After 4 months exposure in dwellings the scatter of 10 dosimeters exposed in the same room exceeds a factor of 3 compared to 15 % for the diffusion chamber. COMPARATIVE STUDY OF TRACK ETCH DETECTORS Detector types and evaluation technique In the comparative study the properties of the following plastic track etch detectors have been applied: - LR 115 from Kodak Pathé, France, is a red dyed cellulose nitrate layer of 13 µm thickness on a 100 µm thick polyester support. The holes appears as bright spots in a dark red background. In an optical microscope counting of through etched [a]-tracks which must penetrate the detector layer - CR 39 from Pershore, England, is an ally1 diglycol carbonate plastic of about 300 m thickness. The normal etched [a]-tracks are counted by an optical microscope and the ECE [a]-tracks by a microfiche reader.

Jan 1, 1981

By John L. Halls

INTRODUCTION In this section, it is assumed that the reader is an engineer with sufficient training in underground mining work, preferably with budgetary control, to understand the mining methods outlined in other sections of this handbook. The mining-method descriptions are not repeated herein; only sufficient information is provided to enable the reader to comprehend the development of the costs presented. All costs are in 1977 US dollars, except where explicitly stated otherwise. CAPITAL INVESTMENT The capital investment in the underground mining portion of any mining property includes the following: 1) The development of original access involving adits, shafts, declines, etc. It includes the necessary equipment for transporting men, materials, and rock. 2) The purchase of mine equipment including loaders, underground haulage equipment, fans, pumps, electrical distribution, surface facilities associated with the underground mine, etc. 3) Sufficient preproduction mine development to assure steadily increasing production after startup. De- pending upon the mining method used, the preproduction development should provide a supply of three months to one year of ore that is developed and is ready to be stoped. Underground development also includes excavations other than shaft stations, loading pockets, sumps, etc., which usually are associated with the means of access and are excavated by the contractor. These excavations could include a crusher cavern, an ore- storage pocket, and underground workshops that may or may not be included by the shaft-sinking contractor. Portions of these could be delayed until after production begins, but it is preferable to complete them during the development phase, so there is no interference with the production buildup. 4) The staff and labor costs for all phases from inception through final production. 5) The provision of mine-surface equipment and facilities strictly applicable to the underground portion of the operation. The required facilities include a changehouse with a lamp room, a first-aid station, compressors, an electrical substation, workshops, a ware- house, water pipelines to the concentrator, water storage tanks, explosive storage, etc. A concrete-batch plant, a sand-fill plant, and boilers for heating may be required. 6) Other direct and indirect costs. 7) Engineering, design, and procurement costs. 8) Contingency allocations. 9) Contractor's fees, startup costs, and owner's costs. Original Access As part of a study for the US Bureau of Mines, Dravo Corp. conducted an extensive literature research survey covering underground operations in the United States between 1963 and 1973. Table 1 is compiled from the section of that study pertaining to the types of access to underground mines. Table 1 does not include distances attributable to the deepening of existing shafts, nor does it include shafts bored by raise drills or downhole machines that need existing underground workings for the disposal of the cuttings. During the period under review in the report ( 1963 through 1973). concrete-lined circular vertical shafts were the predominant means of providing the first access to a new underground mine; these shafts accounted for 80% of the original access in terms of the number of accesses completed, and 75% in terms of the total verti- cal linear distances. The inside diameters of the conventional circular shafts ranged from 3.7 to 7.0 m (12 to 23 ft). Most (72% ) of these conventional shafts were for production,

Jan 1, 1982

By Warren E. Fife

This paper will discuss the application of a continuous miner using a fixed drum milling type cutting head for the underground mining of hard rock and salt ores. Continuous mining machines of the ripper chain cutting head, oscillating milling cutting head and boring arm designs have been used in rock and salt applications with various degrees of success. The large boring arm miners have been successful in potash, trona and salt, but they have not been successful in mining rock materials like iron ore. The main method used in underground mining rock materials is the conventional drilling and blasting the ore from the solid. This is particularly true for the harder, more abrasive copper and iron bearing ores. The softer salt based ores of potash, trona and rock salt can use several underground mining methods depending on seam conditions. Several of these methods use underground coal mining equipment that has been extensively redesigned to adapt it for use in mining noncoal materials. Conventional mining methods employ the use of a universal cutting machine to undercut or topcut the ore body before face drilling and blasting takes place to produce a smooth parting of the ore. The boring arm continuous miner is widely used in underground mining of potash and trona ores. It produces a tunnel with a smooth semicircular contour which results in good rib and roof stability. The ripper chain continuous miner is also widely used in mining the salt based ores of potash, trona and rock salt. They are used more frequently in Europe than in the United States and Canada. Some reasons for using the mechanical mining machines as opposed to the conventional drilling and blasting techniques for mining hard rock ore bodies are the resulting improved rib and roof control, facilitates selective mining of the ore body, and requires less man-

Jan 1, 1974

By Jack Garrity

The Asarco Mission Complex includes two milling operations around a large open-pit copper mine in southern Arizona. The ore body was discovered in 1953 and the complex has been in operation since 1959. The mills provide the concentration operations of crushing, grinding, flotation and filtering processes involved in processing copper ore. Smelting and other downstream processing are accomplished at other Asarco locations. The mine pays a smelting charge to the smelter, which is seen as a service to the concentrators. The higher the concentration of copper to the smelter, the lower the smelting charge is to the mine.

Jan 1, 1995

By Yannis Faitakis, Brenda M. Wright, Gail Powley, Mark Hamblin, Randy B. Paine

A major problem in the ore extraction process is the high degree of variation in the mix of materials that make up the mined ore. The mix of materials makes it extremely difficult to characterize and predict the behavior of the ore when it is processed. The Quality Production Database (QPD) tool was successfully used in order to predict and transfer information regarding the quality characteristics of the ore being delivered to the extraction and hydrotransport unit operators. This paper describes the use of QPD in the prediction of various ore characteristics at the Syncrude Canada Ltd. processing facility.

Jan 1, 2000

By Leons Kovisars

Introduction Labor is the major cost element for most mining operations. Labor costs are continually increasing, both in nominal and constant terms. This is true in developed as well as less developed countries. There are two ways to control unit labor costs - labor costs per ton of ore mined. Replace labor with capital (increased mechanization) or improve productivity (reduce the labor force). Every miner is aware of specific inefficiencies at his or her particular operation. But the miner has no comparative measurement standards. So it is difficult to know whether these inefficiencies are major or minor. The miner may also be unaware of large-scale inefficiencies because ongoing labor practices may have caused management complacency. Met Research studied mining labor productivity. The firm collected pilot data by sending direct-mail questionnaires to 320 nonferrous mining operations around the world. The response rate was 27%, of which 78 operations provided full data on production and employment.

Jan 11, 1983