Search Documents

By D. Marinakis

Gas hydrates (GH) are crystalline compounds consisting of a water molecule lattice, in the cages of which suitably sized molecules, such as methane or other light hydrocarbons, are confined. Although this solid phase looks similar to common ice, it contains substantial amounts of natural gas. The necessary conditions for natural gas hydrate formation exist in some deep-sea marine environments and in permafrost regions. Despite the extensive research, which has been conducted in the fields of exploration and exploitation of natural gas hydrate deposits over the last decades, there is still great uncertainty over the estimated amount of hydrates that these reserves bear. The present work examines some key features of sediments which affect their capacity to host gas hydrates. The hydrate content of a natural hydrate formation is correlated qualitatively with factors such as temperature, effective porosity, mineralogical composition, bio-surfactants, pore pressure and compaction pressure.

Jan 1, 2006

By Kenneth P. Katen

Though the use of continuous mining machines consolidated the operations of cutting, drilling, blasting, and loading in one machine that would theoretically provide uninterrupted production, it was soon realized that the face haulage and roof support operations remained as major impediments to continuous production. The ability to provide not only continuous cutting and loading, but also continuous haulage and roof support (see Fig. I), was the basis for the introduction of mechanized longwall systems in this country from Europe in 1951. The early systems employed friction props for roof support, but were to become obsolete shortly after introduction of the first hydraulically powered, self-advancing supports in 1960. Since then, use of the longwall technique has grown to the point where it is currently providing more than 5% of the annual output of underground coal mines in the United States. The shortwall system had its origin in Australia, but was first introduced into this country in 1962 following the development of powered roof supports. It, too, provides for continuous cutting, loading, and roof support (see Fig. 2), but has not experienced the widespread popularity of longwall due to its inherent inability to easily provide for continuous haulage. While there are in the neighborhood of 100 longwall systems currently in operation in this country, there are only a handful of short- wall operations providing production of slightly more than 907 184.7 t/a (1,000,000 stpy) Both of these systems provide uninterrupted roof support for face operations by means of hydraulically powered steel roof supports. In each case, the coal removal consists of open-end cuts made from the narrow end of a large rectangular pillar (panel) which has been blocked out by continuous miners developing entries around its perimeter. However, this is the extent of the similarities between the two systems. It is hoped [ ] that the information presented in this chapter will enable the reader to better understand the two mechanical systems and the mining concepts involved in their employment.

Jan 1, 1981

By P. R. Taylor

The ability to process complex precious metal sulfide concentrates containing antimony and arsenic in an economic and environmentally safe manner is an important problem facing the mining industry in the United States. Preliminary experiments have been performed to evaluate the possibility of treating a complex sulfide concentrate to recover antimony and precious metals while fixing the arsenic and sulfur as calcium arsenate and calcium sulfate. The process involves: • the oxidation of the antimony and arsenic minerals in the presence of soda ash (to collect the sulfur dioxide and to keep the antimony and arsenic from forming volatile compounds), •the selective leaching of the arsenic from the roast calcine with a heated caustic solution, •the precipitation of the arsenic and sulfate with calcium hydroxide and/or calcium chloride, •the reduction of the residual antimony (collecting the precious metals), •fuming of the metal to form a marketable antimony oxide, and •crucible reduction of the residue to obtain a gold and silver dore. Batch experiments, using synthetic concentrates of stibnite and arsenopyrite, were performed to evaluate the first stage of this process. Variables studied included mixture weight fractions, temperature, gas flow rate, oxygen partial pressure, and time. All of the off gas dust and sulfur containing gases were collected and analyzed. The roast solid residues were subjected to arsenic leach tests, and the leach solutions were subjected to arsenic and sulfate precipitation tests. Introduction The ability to treat a precious metal ore containing appreciable amounts of antimony and arsenic is dependent upon the characteristics of the ore. For some ores, selective flotation can be used to separate the antimony and arsenic minerals, which are then treated separately. Unfortunately, many ores are not treatable in this way, and the concentrates obtained may contain appreciable contamination (which limits the ability to make acceptable grade antimony products). If we consider the added value of the precious metals in the concentrate, then it is worthwhile to evaluate the potential for new methods to treat these types of concentrates. In addition, the environmental difficulties associated with arsenic disposal must be taken into account in any proposed process. If there is appreciable arsenic present, then it must be either recovered as a marketable product or placed in an insoluble form. The problem addressed in this research program has become increasingly important as the precious metals mining industry is encountering more ores of this type. A large deposit of this type exists in Idaho where the antimony occurs primarily as stibnite, with minor amounts of kermesite and tetrahedrite (Cooper, 1951). The gold appears in association with arsenopyrite with minor amounts of other arsenic minerals. Flotation has been used to obtain an antimony concentrate. The concentrate, however, is contaminated with appreciable amounts of arsenic and also contains precious metals. If the ore or concentrate contains appreciable amounts of base metals, then the recovery process becomes much more difficult. There are a number of other known deposits of this type in Alaska, Canada, Montana and elsewhere. The objective of this research program was to develop a fundamental understanding of the oxidation and leaching chemistry of the arsenic and antimony minerals so that technology may be developed to treat these ores in an economic and environmentally safe manner. Wendt (1949) and Koster and Royer (1940) discussed the possibilities of oxidative roasting of stibnite concentrates containing arsenic. Wendt describes a process used at a smelter in Czechoslovakia (in the 1930s) where roasting was carried out in rotary furnaces at 723° K (500° C). Most of the arsenic was removed as fume, as well as 25% of the antimony. No sulfur dioxide containment was described. The oxide fume from the furnace went to a heated caustic water leach, where the arsenic was preferentially dissolved and then precipitated with calcium chloride as calcium arsenate following solid-liquid separation. The antimony oxide was sold, and the solid oxide discharge from the rotary furnace was sent to a blast furnace where the antimony metal, containing the precious metals, was recovered. The metal was fumed to obtain antimony oxide, and the precious metals were left in the residue and collected with copper. The copper

Jan 1, 1994

By Jan K. Wolski

Detection of the air recirculation branches within a large ventilation network may be difficult, therefore a PC computer routine has been developed to perform this task in an efficient and reliable manner. This paper describes the method illustrated using a network with complex multi-recirculation circuits. The fact that only the air flow directions and not the flow rates are used in calculations is of some interest. The air recirculation during a real mine fire is demonstrated using the PCVENT program, whose version 4.0 includes current information about any recirculation branches during network calculations or during a fire simulation. This paper also discusses some transient problems related to air recirculation, and gives examples.

Jan 1, 1993

By F. Seymour

A modified three-dimensional Lerches-Grossmann (LG) graph tree algorithm that generates the complete set of nested maximum valued pits in a single run is presented. This modified LG algorithm looks at the relative strength (average value) of the branches (groups of blocks). Pointers are allocated and pruned until there are no members of weaker (lower average value) branches overlying members of stronger (higher average value) branches. The final set of strong branches arc listed in order of decreasing strength. The pits they represent form the maximum valued convex hull for a single-variable pit-limit parameterization. A description of the algorithm is given along with examples of lion it has been applied at Newmont.

Jan 1, 1996

By John Litz

The term "refractory gold ores" refers to a wide number of ore types which are not readily amenable to direct cyanidation. A number of processes have been used commercially, and a number of others have been proposed and in many cases pilot tested. The selection of the appropriate process for an ore should not be arbitrary. Ore grade may preclude some processes, but a good understanding of the ore mineralogy can guide the selection. Many present gold operations and many potential gold operations have faced or are facing problems with refractory gold mineralization. We at Hazen Research have had the opportunity to perform bench testwork and in some cases, pilot plant testing on a number of refractory ores. The data included in this paper are excerpted from the testing of fifteen ores which cover a wide range of mineralogical compositions. This paper is not intended to be a treatise on the processing of refractory gold ores. In many of these gold projects, not all of the standard process alternatives were evaluated, nor was adequate mineralogical work performed. Such is the dilemma of contract research. "If I believe that I don't need it, why should I pay to have it done." The intent of this presentation, therefore, is to show how different ores respond to the various processes, and to demonstrate that one must have an open mind when developing a process for a specific refractory gold ore.

Jan 1, 1998

By Cuong V. Trang, Christopher A. Fleming

There has been greatly renewed interest throughout the gold mining industry over the last few years in cyanide recovery from gold and silver plant tailings. This interest has been spmred by two factors. Firstly, the increasing cost of destroying cyanide to levels that meet more and more stringent regulations for tailings impoundment or discharge to the environment. Secondly, many gold ore bodies suffer high cyanide consumption costs as a result of the presence of base metals (principally copper) that react with and consume cyanide during the gold leach. In most cases, the cost of recovering and recycling this cyanide from the tailings is signif­icantly lower than the cost of purchasing new cyanide. When this cost benefit is added to the lower costs of tailings detoxification, a compelling case can frequently be made for cyanide recove1y. A number of processes for recovering cyanide from gold plant barren solutions or pulps have been developed. Most of the processes require that the recoverable cyanide is first converted to the highly toxic hydrocyanic acid gas (HCN) and fears surrounding the handling of this compound have probably presented the great­est impediment to implementation of these processes.

Jan 1, 1998

By F. Dingwu

The demand of manufacturing high-purity magnetite concentrate leads to the advent of various magnetic separators. A novel magnetic drum separator has been developed with an optimal permanent magnet system and a complex-forces field is adopted, involving magnetic force, gravitation, fluid resistance, friction, inertial centrifugal force, etc. Proper ultrasonic probes are inserted into the bottom tank to break up the magnetic floes. The performance of magnetite in the complex-forces field is described and the optimal operation conditions are suggested.

Jan 1, 1995

By Jianping Sheng, Francis Otuonye

The potential for methane and coal dust explosions in underground coal mining operations has increased in recent years with the introduction of fast coal-cutting machines. Dust explosions usually follow accidental ignition of a methane pocket. The dynamics of the explosion may be strong enough to pick up and disperse coal dust deposited on mine surfaces and ignite the mixture. A self-sustaining dust explosion can then develop and propagate at large distances. Ignition of dusts can result in a fire, and this may also lead to a dust explosion if the burning dust becomes airborne. Entrainment of dust and the resulting dust concentration in the gas stream are some factors which determine the features of the subsequent explosion and flame propagation. A model of coal dust transport in the gas stream due to the initial explosion is presented. In this model, equations for the conservation of mass, momentum and energy are coupled with the convective-diffusive model of dust transport. The system of equations is solved numerically to obtain dust concentration, convective velocity and gas pressure profiles.

Jan 1, 1989

By K. C. Liddell

Chemical processing research made notable advances during 1986. This overview is necessarily brief. It is intended, though, to give the flavor of selected areas where recent activity has been high. At the 1986 Annual Meeting of The Metallurgical Society, a symposium was held on hydrometallurgical reactor design and kinetics. R. G. Bautista, R. J. Wesely, and G. W. Warren edited the resultant proceedings volume. This is the first available volume on this subject. It includes 26 papers on fundamental kinetic studies, modeling of reaction kinetics and reactor performance, and pilot and production-scale operations. Metals discussed include silver, gold, platinum, titanium, cobalt, nickel, zinc, copper, manganese, and iron. Agitated tanks, heaps, dumps, pachucas, pressure auto-claves, electrolytic reactors, liquid membranes, and fluidized beds are among the reactor types covered. An international symposium dealt with iron control in hydrometallurgy. It was sponsored by the Metallurgical Society of CIM, the Institution of Mining and Metallurgy, The Metallurgical Society of AIME, and Gesellschaft Deutscher Metallhutten and Bergleute. J. E. Dutrizac and A. J. Monhemius edited a proceedings volume containing 41 papers. These covered many areas of process chemistry, solvent extraction, precipitation, treatment of pickle liquors, impurities, residues and the environment, and process selection. Precious metals Concerning precious metals processing, the US Bureau of Mines IC 9059 is noteworthy. It includes papers presented at a USBM briefing at the Western Mining Conference in Denver. Topics covered included ion exchange, staged heap-leaching direct-electrowinning, and mercury precipitation during cyanide leaching of gold ores. Also dealt with were carbonaceous gold ores, carbon adsorption and desorption, heap leaching, the carbon-in-pulp process, and precious metals recovery from electronic scrap and solder. R. C. Sandberg and J. L. Huiatt (Journal of Metals, June 1986, and USBM RI 9022) developed a method to recover silver, gold, and lead from a complex sulfide using ferric chloride, thiourea, and brine-leach solutions. Gallium Gallium recovery was also a subject of considerable interest. Much information on this topic is proprietary. But two papers described solvent extraction of gallium. V. P. Judin and R. G. Bautista (Metallurgical Transactions B, 1986) developed an equilibrium model to separate gallium chloride from aluminum chloride. Tributyl phosphate was the extractant studied. T. Sato and H. Oishi (Hydrometallurgy, 16, 1986) investigated gallium extraction from sodium hydroxide by using Kelex 100. Data were given on the equilibrium distribution and the extraction kinetics. Galena Interest continues in recovering lead by hydrometallurgical processing of galena. J. E. Dutrizac; S. H. Kim, H. Henein, and G. W. Warren; and M. C. Fuerstenau et al. (Metallurgical Transactions B, 1986) all investigated leaching of PbS by ferric chloride. Dutrizac reported parabolic kinetics and reaction control by outward diffusion of lead through a porous layer of elemental sulfur. Kim, Henein, and Warren, however, reported that two leaching reactions occur. A nonoxidative reaction produces H2S and there is an oxidative leaching by ferric ion. Acid dissolution was found to predominate when the acid activity to ferric activity ratio is high. Surface chemical reaction was reported to be controlling. Fuerstenau et al. also reported that mass transfer through the sulfur layer is rate determining. But they believe that the species transferred are chloro complexes of ferric ion. In other work on lead, A. Y. Lee, A. M. Wethington, and E. R. Cole, Jr. of the USBM described an environmentally acceptable hydrometallurgical alternative to the smelting of lead concentrates (RI 9055). Uranium In spite of depressed prices, much work has been reported on uranium processing. R. G. L. McCready, D. Wadden, and A. March-bank (Hydrometallurgy 17, 1986) described the nutrient needs for in-place leaching by T. ferrooxidans. They reported the optimal conditions for uranium solubilization. L. E. Eary, H. L. Barnes, and L. M. Cathles (Metallurgical Transactions B, 1986) carried out an experimental and modeling study of uraninite dissolution. They concluded that ferric ion preferentially leaches uraninite in pyritic ores. Hydrogen peroxide was found to be less selective. A. Vuorinen, P. Hiltunen, and O. H. Tuovinen (Hydrometallurgy 15, 1986) studied redox and precipitation reactions of iron and uranium in leach liquors. P. T. Chiang (Hydrometallurgy 17, 1986) reported on the effect of uranium loading in the DEPA-TOPO process to separate uranium and iron from wet-process phosphoric acid. F. J. Hurst (Hydrometallurgy 16, 1986) conducted a fundamental study of the separation of uranium from phosphoric acid by DEPA and TOPO. D. E. Chia and W. C. Cooper (Hydrometallurgy 16, 1986) reported on bench and pilot scale work to recover uranium by the HIMIX process. They reported that the acid consumption to produce an eluate suitable for yellowcake

Jan 5, 1987

By X. Baolin, R. Guru, M. Peiravi, M. K. Mohanty, Z. Qian, R. Ma, Z. Yude, L. A. Ackah

"Acid mine drainage (AMD) is produced when exposed pyrite (FeS2) reacts with air and water to form an acidic solution that usually contain contaminant levels of heavy metal ions. AMD can potentially contaminate surface water and soil if not treated. The primary objective of this study was to investigate the removal of dissolved aluminum, iron and zinc metal ions from natural AMD using water treatment residue (WTR), a low-cost adsorbent. WTR sorbent generated as waste material in drinking water treatment plants (WTP) was characterized and utilized for the sorption of Al, Fe and Zn in AMD collected from an abandoned coal mine site in southern Illinois that generates approximately 20 gallons per minute of AMD. Sorption experiments were performed using batch technique to obtain rate and equilibrium data. The effects of various parameters on sorption capacities of WTR were observed by varying contact time, pH of the AMD and WTR dosage. The adsorption studies showed rapid uptake in general for the first 80 minutes for Fe and Zn but much earlier for Zn. Further increase in contact time did not show significant change in equilibrium concentration indicating the onset of adsorption equilibrium. After the batch treatment of the AMD water with the WTR, the removal of Al, Fe and Zn were 99.8%, 99.85% and 95.5% respectively. The pH of AMD increased from 2.64 to a near neutral point of 6.74 after treatment. The laboratory results show that the low-cost WTR, which is an abundantly available industrial waste, has proven potential to significantly reduce the high metal ions in acid mine drainage. INTRODUCTION Mining activities provide the basic raw materials needed for infrastructure development and economic growth world-wide. However, it is well recognized that mining activities have been the cause of a variety of environmental pollutions, including AMD. Water seeping out of an old abandoned mine is generally characterized by low-pH with heavy loads of dissolved sulfates (SO4) and metal species such as Fe, Al and Zn among other dissolved elements categorized as toxic metals. The Bureau of Land Management’s Abandoned Mine Lands (AML) program reported the existence of about 46,000 abandoned mines in the United States. Several environmental problems have been reported to be associated with these mined out sites such as heavy metal poisoning, loss of vegetation, air pollution etc. (Boulanger & Gorman, 2004)."

Jan 1, 2017

By Anthony Edey, Leigh A. Readdy, Bruce A. Kennedy

Introduction Very little attention normally is given by the experts, or the public at large, to the fact that the majority of the oil that has been or will be discovered within the U.S. remains in the ground. The inherent limitations of oil production through surface wells, either by primary or secondary techniques, will result in a total of over 300 billion bbl of oil left in the ground after completing production by standard petroleum techniques in currently producing or producible fields. This reserve represents some two-thirds of the original quantity of oil discovered in place. Recent work by a number of groups has shown that there is strong economic justification for extracting this remaining oil by mining and processing techniques. Table 1, taken from 1977 API reports, demonstrates the oil left in place at the end of the conventional petroleum production cycle in then-known fields within th’e U.S. Possible targets for oil mining operations include (1) oil remaining in place in fields and pools that have reached economic depletion by current petroleum production methods and that are not amenable to economic recovery by conventional petroleum industry techniques; (2) oilor bitumen-saturated rocks not normally considered by the industry to constitute producible reservoirs, such as shales and diatomites; and (3) asphalt- and bitumen-impregnated rocks. Economically Depleted Fields A more detailed examination of the depleted fields shows that estimates of oil remaining in place after primary, secondary, and nondestructive tertiary recovery can vary widely. There is significant evidence, however, that more than half the estimated original oil in place (OOIP) remains in the reservoir after all petroleum extraction techniques have been applied. If one compares the sum of past oil production and estimated remaining producible reserves with the API estimate of total discovered OOIP as of 1975, it becomes apparent that for the U.S. as a whole, 67070of the 00IP will remain in place at the end of the

Jan 1, 1980

By Anthony Edey, Leigh A. Readdy, Bruce A. Kennedy

Introduction Very little attention normally is given by the experts, or the public at large, to the fact that the majority of the oil that has been or will be discovered within the U.S. remains in the ground. The inherent limitations of oil production through surface wells, either by primary or secondary techniques, will result in a total of over 300 billion bbl of oil left in the ground after completing production by standard petroleum techniques in currently producing or producible fields. This reserve represents some two-thirds of the original quantity of oil discovered in place. Recent work by a number of groups has shown that there is strong economic justification for extracting this remaining oil by mining and processing techniques. Table 1, taken from 1977 API reports, demonstrates the oil left in place at the end of the con¬ventional petroleum production cycle in then-known fields within the U.S. Possible targets for oil mining operations include (1) oil remaining in place in fields and pools that have reached economic depletion by current petroleum production methods and that are not amenable to economic recovery by conventional petroleum industry techniques; (2) oil-or bitumen-saturated rocks not normally considered by the industry to constitute producible reservoirs, such as shales and diatomites; and (3) asphalt- and bitumen-impregnated rocks. Economically Depleted Fields A more detailed examination of the depleted fields shows that estimates of oil remaining in place after primary, secondary, and nondestructive tertiary recovery can vary widely. There is significant evidence, however, that more than half the estimated original oil in place (OOIP) remains in the reservoir after all petroleum extraction techniques have been applied. If one compares the sum of past oil production and estimated remaining producible reserves with the API estimate of total discovered OOIP as of 1975, it becomes apparent that for the U.S. as a whole, 67% of the OOIP will remain in place at the end of the

Jan 9, 1980

By E. Jong, E. Watkins

"The application of passive tracer gas sources in underground mines is particularly useful for long-term tracer studies as well as for studies conducted in permissible areas of underground coal mines. The use of passive perfluoromethylcyclohexane (PMCH) sources has been previously demonstrated in underground mines, but this new work details the testing of multiple, distinct tracer compounds compatible with passive sources. A description of their potential application in mine ventilation systems is also provided. Three tracer compounds are detailed: (1) PMCH, (2) perfluoroethylcyclohexane (PECH) and perfluoromethylcyclopentane (PMCP). The release rates of these tracers were examined over a 180-day period at multiple temperatures. The advantages and disadvantages of these sources are presented, along with potential applications in characterizing ventilation circuits, flow through gob and leakage. IntroductionThe use of tracer gases for ventilation applications is an established practice, with various past research projects conducted using sulfur hexafluoride (SF6). Tracer gas techniques have been applied to assess flow rates, dilutions rates and auxiliary ventilation system efficiencies with quick, reliable and accurate results (Suglo and Frimpong, 2002). Perfluorocarbon tracer (PFT) compounds are a new introduction to ventilation and air modeling applications in terms of ventilation flow characterization (Watson et al., 2007).PFTs are liquids that are characterized by low background presence in air, low reactivity, high detectability and low toxicity. A design was proposed, called a permeation plug release vessel (PPRV), to convert PFTs from a liquid to a gas and then release the gaseous tracer in a controlled manner. The initial concept was originally introduced by Brookhaven National Laboratory and refined later to become the PPRV. The PPRV functions by allowing the volatile PFT liquid to become a vapor in a controlled manner. The vapor diffuses through a permeable silicone stopper at a predictable rate proportional to temperature (Zhang and Cloud, 2006)."

Jan 2, 2018

By Olli Järvinen

The precious metal refinery process is divided into the five process stages: 1 .copper/nickel leaching in autoclave 2. selenium roasting furnace 3. doré metal smelting furnace 4. silver electrolysis 5. gold recovery system. The process has been developed during the years in Outokumpu Harjavalta Metals, which treats about 600000 kg /year copper anode slime. The slime treatment process route in Outokumpu Pori plant has been developed from year 1941. During this period the process has been improved radically. The major changes has been the atmosphere leaching into the autoclave leaching, the sulfuric acid roasting furnace was changed into sulfuric dioxide / oxygen roasting. The old doré smelting furnace has changed into the TROF converter and the gold electrolysis / aqua regia process has changed into the quick hydrochloric acid leaching process. The current production in Pori plant is 30000 kg of silver, 1000 kg gold, 30000 kg of selenium and some hundred kg of platinum- palladium concentrate.

Jan 1, 1995

By Gregory W. Gustina, Terry P. Boyle

Analysis of the structure of the benthic macroinvertebrate community, consisting of the number of taxa and the relative distribution of total numbers, is a routine method of assessing the ecological quality of streams. Various multivariate statistical techniques, which assess the structural variability of the benthic macroinvertebrate community and the relationship of that variability with natural and anthropogenic environmental variables, have utility in separation of the various physical and chemical factors associated with impact. Multivariate methodology, while computationally complex is statistically rigorous and better integrates physical, chemical, and biological data for more synthetic interpretation. Using the multivariate analysis technique, canonical correspondence analysis, we have analyzed a number of sites in the upper Boulder River Basin, Montana to determine which are the important environmental variables associated with variation in community structure. The results of this analysis an integrated with more traditional analysis of community structure and incorporated in a risk analysis for the mediation of abandoned mines and mill sites within the watershed.

Jan 1, 2000

By M. Kumral

The in-situ mineral characteristics of a deposit are simulated by sequential co-simulation and averaging the simulated characteristics within specified block volumes creates a three-dimensional block model. This model is then submitted to optimal open pit and production scheduling algorithms. As the market values of industrial minerals depend on the satisfaction of predetermined blending criteria rather than metal content, a Linear Programming (LP) scheme has been used to identify all blocks that can be included in the blend without violating the grade requirements. The Lerchs-Grosmann algorithm using the blocks identified by the LP program determines optimal pit limits. All blocks that lie outside the optimal pit are removed from the system and the blocks within the optimal pit are submitted to the production-scheduling algorithm. Production scheduling optimisation is done in two stages: Lagrangean parameterisation, resulting in an initial sub-optimal solution, and multi-objective simulated annealing (MOSA) improving the sub-optimal schedule further.

Jan 1, 2002

By W. David Tyler

Any mining or engineering-construction excavation that extends below the water table must be dewatered. In many situations, the ground is of low permeability or the workings extend only a short distance below the water table. So water removal can be handled easily and economically by using mobile centrifugal pumps. However, there is an increasing number of mines that have a continuous high flow of water into the workings. Controlling this flow can significantly increase the cost of ore production. Successful implementation of any major dewatering scheme will ultimately rely on a clear understanding of the local geology. This understanding is necessary before an interpretation of ground water conditions can be made. It will dictate which dewatering methods are feasible. Once the geology and the ground water system are known, the scope and timing of the dewatering measures can be varied with the mine plan. Ground water modeling can assist in optimizing the dewatering system, though the precise objective of each model should be clearly defined. Production wells must be sited and drilled so that individual well efficiencies are high. Any lost efficiencies will translate into higher operating costs. Each well must be designed for maximum long-term control of the water table, and pumps sized to operate under continually changing heads. Finally, the investment in each production well must be protected during the mining process.

Jan 1, 1991

By Roberto de Moraes

Lunar construction faces unique challenges arising from the nature of regolith and megaregolith. Unlike terrestrial soils shaped by weathering, lunar regolith is composed of angular, poorly sorted particles produced by impacts, with bulk Density, strength, and trafficability varying sharply with depth and terrain. Boulder fields, floaters, and talus aprons add further complexity, disrupting excavation and mobility. Apollo missions documented these conditions through drive-tube samples, trenching, penetrometer data, trafficability tests, and seismic profiling, but the results remained as datasets rather than a unifying classification. This paper introduces the LRC (Lunar Regolith Classification) Framework and the Overconsolidation Ratio applied for the Moon (OCR*), the first contractor-ready system to organize Apollo-derived trends into excavation demand zones (L1–L5). LRC is explicitly a classification, not a stratigraphy: depth ranges are indicative and require in-situ verification before use. Each zone is defined by bulk density and strength ranges, field proxies (bootprints, trench stability, auger torque, seismic contrasts), and corresponding excavation implications. Worked examples from Apollo 15 (mare), Apollo 16 (highlands), and Apollo 17 (pyroclastics and talus) demonstrate how observed data translate into LRC zones. These cases show that LRC captures both systematic depth trends and sharp local heterogeneity. The framework standardizes excavation planning for landing pads, haul roads, berms, foundations, and tunneling trials, while converting floaters from hazards into resources. LRC thus provides a common language for lunar construction. Rooted in Apollo evidence but designed for Artemis verification, it is proposed as a living standard; a reference framework to guide site preparation, excavation, and risk management in the next phase of lunar development.

Feb 22, 2026

By J. E. Oberholtzer, M. G. Fernald

INTRODUCTION Approximately six years ago the U.S. Bureau of Mines (USBM) developed a data acquisition system (DAS) specifically designed for measuring radon levels and other environmental parameters during studies of means to control radiation hazards in underground uranium mines. The DAS system records data in machine readable form using a paper tape punch, which represented the state-of-the-art at that time for a moderate cost output device. However, the use of paper tape as a recording medium for field studies is somewhat unwieldy. Reducing the raw data required either that the tape be shipped to a computer center equipped with a high-speed paper tape reader or that the tape be transmitted at low speed over the telephone lines to a remote computer. Transmitting, at ten characters per second, the data from a 10-channel DAS taking Four readings per hour would require about 30 minutes For each 24-hour day's data. Telephone lines from remote mine sites are often of marginal quality and data errors can be introduced during transmission. Paper tape punches are also prone to occasional punching errors. Both problems make it necessary to carefully check for and correct data errors, a process which is possible because each DAS produces an independent printed data record, but the error checking and correction process can be quite laborious. Aware of recent advances in microcomputer technology which have brought the price of a personal computer down to about the cost of a paper tape punch 5-10 years ago, the Bureau decided to explore the feasibility of using a low-cost personal computer in the field to process DAS data in real time. On behalf of the Bureau, Arthur D. Little, Inc., developed a simple interface circuit which permits an Apple II computer to accept data from one or two DAS units as it is being transmitted to the paper tape punches. Computer software converts each measurement to appropriate engineering units, e.g., radon concentration, Working Levels, air velocity, temperature, or barometric pressure. The computer also calculates 1-hour and 8-hour running averages of all converted data and prints those results as soon as they are obtained on a line printer located at the test site for immediate inspection. After development, the system was used continuously and successfully for a 5-month period at a Utah uranium mine. DAS DESIGN AND MODIFICATION Each of the two USBM data acquisition systems used in this work consists of two separate modules. A multiplexer module located below ground near the measurement transducers acquires signals from each of nine tranducers. Six input channels were devoted to measurements of radon or Working Level. The outputs of those transducers, photomultiplier tubes or G-M tubes, respectively, are digital pulse trains which are accepted directly by the mutliplexer. Three channels were used for environmental parameters--air velocity, temperature, and/or barometric pressure. Each of the environmental tranducers is fitted with dedicated linearizing and voltage-to-frequency conversion circuitry so that the outputs to the multiplexer are also pulse trains having frequencies of one tenth of the value of the measured parameter expressed in the appropriate engineering units. A 100-Hz reference signal was input into the tenth channel for use in monitoring system integrity and performance. All ten pulse trains are then timeseries multiplexed into a signal line for transmission to the above-ground data acquisition module. Above ground, the composite signal is de-multiplexed into ten separate lines, each of which is connected to a digital counter which converts the pulse train to a numerical value. The acquisition of each set of readings is initiated by an adjustable "scan cycle comparator" timer. The acquisition process proceeds in three phases. First, radon and Working Level channels are counted for an extended period of time, typically 5-10 minutes depending on activity, because of the low pulse rates involved. Then the other four channels are counted for ten seconds, and finally, all ten readings, along with the Julian day and time of day are output serially onto paper tape and printed on a strip printer. When the scan cycle comparator reaches its preset time (15-minute cycle times were used in this work), it resets itself, initiates another readout cycle, and begins timing again. The only modification made to the data acquisition systems used in this work was to disconnect the scan cycle comparator in one unit, which became the "slave" and bring in the scan cycle comparator signal from the other unit, the "master", to initiate data acquisition cycles in the slave. Synchronizing the two data acquisitions in this fashion and using two slightly different radon counting times insured that the two systems never attempted to output data to the Apple II at the same time. THE APPLE II COMPUTER The Apple II computer used in this work was equipped with 48 KBytes of semiconductor random access memory (RAM), two floppy diskette drives, a Centronics Model 730 impact matrix printer and a modulator for driving an ordinary color television as a video display device. A single California Computer Systems Model 7720A dual 8-bit bidirectional parallel input/output (I/O) card was installed in the Apple to accept the digital data from both data acquisition systems. This card is

Jan 1, 1981