Search Documents

By W. M. Shaver, W. R. Dengler, F. A. Edwards

INTRODUCTION The Macassa Division of Lac Minerals Ltd. is a high grade gold mine that has been operating in Kirkland Lake, Ontario for the past 51 years. It produces approximately 120,000 tonnes of ore per year, averaging approximately 18.7 grams per tonne (0.45 ounzes per ton) of gold. Over the years, the ore body has been developed to a point where mining takes place below the 1,220 m (4,000 feet) elevation and 1,830 m (6,000 feet) west of the original shaft. The mine is currently serviced by two surface and two winze shafts. (Figure 1). The ore body extends below the 1,930 m (6,400 feet) Level which is the bottom of the existing mining operation. An ambitious underground exploration program has substantially increased these reserves. Concurrent with the discovery of greater reserves, has been rapidly escalating mining costs, particularly labour which constituted 66% of the total cost in 1981. These costs continued to escalate as the major proportion of mining was carried out to the west, far away from the existing hoisting systems. This required three lift hoisting for men, materials and ore. I n addition to the increased travel time and ore handling expense, increased humidity and temperature and ventilation and compressed air losses have added to the inefficiency of the operations. As a result, studies were initiated in 1980 to assess the future of the Macassa operation.

Jan 1, 1985

By S. Afrouz, C. Keles, E. Sarver, A. Greth

While respirable dust monitoring has long been done on the basis of mass concentration, it is increasingly recognized that specific dust characteristics may play an important role in health outcomes. Scanning electron microscopy with energydispersive X-ray (SEM-EDX) can be used for detailed particle analysis, but the quality of results can be dependent on the sample substrate; ideally, particles should be deposited on a smooth, uniform substrate like polycarbonate (PC). While direct air sampling onto PC filters is possible, this is not the standard approach in many situations. For example, in coal mines, polyvinyl chloride (PVC) filters are often used. They enable conventional mass-based analysis — of the total respirable dust, and the content of crystalline silica in this fraction — but are fibrous and thus not ideal for SEM-EDX or other microscopy. To address this issue, the current work tested a simple method to recover respirable dust particles from PVC filters and redeposit them to PC. Results generally indicated that recovered particles are representative of the original dust sample in terms of mineralogy distributions. Where this was not the case, the issue appeared to be with high particle loading density during SEM-EDX work rather than related to the recovery/redeposition method itself. This bodes well for applications where a single PVC filter sample could be used for nondestructive analysis to determine respirable dust mass and/or respirable silica mass, followed by preparation for SEM-EDX analysis to evaluate particle characteristics. The recovery and redeposition method might also be adapted for other applications, such as to enable the analysis of respirable dust samples collected by the continuous personal dust monitor (CPDM).

Oct 1, 2024

By N. E. Norman

A great deal of effort has been put forth in recent years to arrive at accurate projections of the demands for tunnels in this decade. In reviewing the statistics presented by various study groups, it appears that during the decade from 1960-69, there were some 1,335 miles of rock and soft ground construction tunnels excavated throughout the world. These statistics indicate 645 miles of rock tunnel and 689 miles of soft ground tunnel were excavated during the last decade. This is expected to increase to 3,000 miles in the 1970's according to projections made by various authorities in the field of construction tunneling. I point out the above statistics to emphasize two main points: (1) The demands for tunneling in this decade alone are staggering. (2) There is a fairly even distribution in the amount of rock tunneling and soft ground tunneling being excavated. Unfortunately, available statistics do not answer many important questions about tunneling which are of great importance to the contractor and to boring machine designers. For example, how many of the projects completed in the past decade involved both soft ground and rock tunneling? How many projects involved tunneling in conditions where both rock and soft ground were contacted at the same face. While the answers to these questions remain unanswered, I am sure most of you can think of numerous examples of projects where mixed face conditions are prevalent. Many of you are probably familiar with the Austin Crosstown Interceptor which was bid last month in Austin, Texas. Here is a project involving 57,000 feet of tunnel where limestones and clay shales are expected to be traversed. Another project, the Tonner Tunnels No. 1 and No. 2, near Los Angeles, involve some 22,000 feet of tunnel where mixed soil and rock conditions are expected. A large majority of the projected tunnels for this decade are to

Jan 1, 1997

By Roy Moreby

Dartbrook Coal is currently developing a modern, high production (3.5 Mtpy) single longwall retreat coal mine in the Upper Hunter Valley of NSW, Australia. The location is a green field site, with no surface or underground mining operations ever having taken place in the initial target seams. The coal seams of the working section, floor and immediate roof average a total 20 m in thickness and contain a mixed carbon dioxide 1 methane seam gas ranging from 6.5 to 11.0 m3/t. The target seams have undergone detailed characterisation to assess hazards and quantify the controls required to minimise associated risks during mining. Risks identified during initial phases of exploration and 14 months of development include: • High gas emission during development. • Probable high longwall gas emission rate. • Medium to high propensity to spontaneous combustion • Possible carbon dioxide outbursts on geological structures • The main controls currently in place include, • Mine geometry and ventilation circuits • Exploratory drilling ahead of development • Intensive in seam pre drainage • Goaf drainage plants • Comprehensive monitoring systems • Underground environmental management plan. • Pre mining predictions of gas emission provided an indication of gas emission rates which have proven to be an under estimate. Current mine issues are; • Both surface fans are at full capacity (250 m3/s 1.4 kPa) • Both gas drainage pumps are at full capacity (2.3 m3/s) • Alternatives to extensive in seam pre drainage being investigated (surface to in seam hydro fracture) Review of mine design underway This paper describes the seam characterisation, assessment of mining hazards and summary of the management plan developed to address the risks identified. A review of current mine underground environmental performance is also provided

Jan 1, 1997

By Raymond E. Krauss

The McLaughlin Mine is a world class epithermal gold deposit located in the coastal thrust fault of Northern California, U.S.A. Homestake adopted a proactive strategy in the permitting of the Mine. Extensive environmental baseline studies were undertaken. Engineering and process alternatives were evaluated for environmental impact along with other factors. A unique pressure oxidation process was selected. Screening studies were conducted as a basis for the selection of waste rock and tailings disposal sites. Project engineering and permitting were fast tracked. Construction required eighteen months, and the first gold bar was poured in March of 1985, six years after the initial discovery. Project facilities are designed and operated so as to minimize environmental impacts. A comprehensive monitoring program demonstrates permit compliance. Reclamation of the site is ongoing throughout the Mine's twenty year life. Nonmined lands are managed to maximize wildlife habitat value.

Jan 1, 1990

By R. C. Richardson

Barite Worldwide barite production for 1985 decreased 1.3%, while US barite production increased 1.4%, according to US Bureau of Mines statistics. The increase in US production is attributed to heavy demand for oil and gas drilling during the first quarter and an unrealized heavy expected demand in oil and gas markets for the last quarter. Nevada accounted for 82.1% of the 807 kt (890,000 st) of barite produced in the US last year, according to the Bureau. Other producing states were California, Georgia, Illinois, Missouri, Montana, Tennessee, and Washington. In 1985, the US imported 1.8 Mt (2 million st) of crude barite and 64 kt (71,000 st) of ground barite. China led the way with 43.3% of the total. Imports from India accounted for 21.6%; Morocco, 15.5%; and Thailand, 5.6%. The 1.8 Mt (2 million st) of crude barite imported is an 18.8% increase over 1984. Apparent consumption of barite for 1985 was about 2.6 Mt (2.9 million st), a 15.7% increase from 1984. Due to very low drilling rig activity during the last quarter of 1985, actual consumption is probably less as crude barite inventories at mines and plants increased. According to the Bureau, 90% of barite consumed in 1985 was for the oil and gas market. Paints, rubber, glass, and other chemical uses consumed the other 10%. With the price of oil falling dramatically early in 1986, the outlook for oil and gas drilling looks to be significantly lower than 1985. This lower demand for barite, coupled with the high year-end inventories, should lower both imports and domestic production. Significant lower prices on imported barite are expected, especially from China, Morocco, and India. This also could further lower US production of barite this year.

Jan 5, 1986

Selective Flocculation process development generally involves single mineral flocculation tests to identify the appropriate polymer and experimental conditions for achieving the desired selectivity. Invariably the selectivity predicted on the basis of such tests is not realized when mixed mineral tests are conducted. A systematic experimental investigation revealed that adsorption of the polymer on various substrates is critical to selecting the suitable flocculent. Simultaneously, a mathematical model was developed to predict the overall process efficiency with a given polymer. In this paper, results of these efforts to scientifically design a suitable selective flocculation process are presented.

Jan 1, 1991

By A. J. Basu

A prototype expert system for planning and designing underground coal mines has been developed in a doctoral study (Basu, 1991) at the University of Kentucky (U.K.). The objective of the study was to provide a design tool for configuring layout parameters, production systems, and for determining economic feasibility. Details of knowledge engineering and the prototype knowledge-based system for integrated and intelligent planning and design have been covered in the dissertation. The prototype demonstrates its robustness by allowing interaction among major design components, most notably among ventilation, ground control, and production planning. A plan for testing and evaluating the prototype, an important phase of software development, is presented here. Existing evaluation procedures for expert system prototypes are discussed and the evaluations for the underground coal mine design expert system prototype are included. The initial testing plan used senior-level mining engineering students to test the acceptance of the prototype. This test suggested the usefulness of such a system for training and instruction. This initial acceptance test was performed with the feasibility prototype. The other test objective, i.e., testing the model's accuracy, involved extensive participation of domain experts. For overall accuracy evaluation, an existing underground coal mine design was compared with the output from a design session using the expert system prototype. The testing procedure is not an isolated, independent development phase. Much of the accuracy evaluation is done at the time of knowledge base development. Therefore, the knowledgebase itself does not need a formal test phase. The major purpose of the field testing is to determine probable user acceptance. The acceptance test determines the completeness of the prototype and also will determine efficiency of user interfaces.

Jan 1, 1992

By Y. C. Kim, M Nataraja, J. T. Buckley, D. H. Tiktinsk

The Nuclear Waste Policy Act of 1982 (NWPA) assigns the U.S. Department of Energy (DOE) the responsibi1it.y of locating, constructing. operating, closing and decommissioning a nuclear waste repository. Prior to submittal of a licensee application to the U. S. Nuclear Regulatory Commission, the DOE is required by 10 CFR part 60 to conduct a program of site characterization for the site to be described in such application. Site characterization includes an exploration and research program in the field and laboratory to determine the geologic conditions and ranges of those parameters which are necessary for determining the suitabi1it.y of the site as a geologic repository. The information thus collected should be able to establish with reasonable assurance that the public and environment will be adequately protected from the hazards associated with a repository at the site. This paper demonstrates by example a geostatistical approach which, on the basis of the existing limited data base, can be used to evaluate (1) whether existing information on a certain parameter is adequate to be considered representative. (2) if additional information is required, where should the additional sampling or testing be performed, and (3) whether the new1.y acquired data along with the existing information constitute representative data.

Jan 1, 1986

By Lewis. Clifford J.

The purpose of this article is to present design information and operating data on a pilot gas scrubber which is believed to be a new approach for removing noxious gases and particulate matter from the off gases of coal burning power plants and smelters. This principle of scrubbing gases, particularly, scrubbing with an aqueous slurry of lime, was conceived by the author early in 1972. The National Lime Association financed the design, fabrication and initial operation of the unit. The unit was fabricated by Hazen Research Inc. of Golden, Colorado. It has been tested on the off gases of two coal burning power plants and one smelter. The current environmental program has stimulated research and development activity directed toward the removal of sulfur oxides, oxides of nitrogen, particulate matter and other undesirable substances from gases discharged into the atmosphere. At present, most of this effort is focused on the removal of sulfur dioxide and particulate matter by aqueous scrubbing of the gases. This presentation deals particularly with the removal of sulfur dioxide using an aqueous slurry of lime as the scrubbing medium. In recent papers, the author has called attention to-the sludge problems resulting from aqueous scrubbing and to some earlier data on the pilot scrubber about to be discussed.1/

Jan 1, 1973

By Zhonglin Ye, Guangping Dai, Ba Zhang, Yonggang Wei, Shiwei Zhou, Bo Li, Hua Wang

Decreasing copper content in slag is critical for improving copper recovery, where apparent viscosity is the main factor affecting the separation of matte/copper from the slag. The viscous behavior of copper converter slag was investigated during reduction process in this paper, and its non-Newtonian viscous behavior and shear thickening characteristics were clarified. The effects of silicate structure and solid particles in the melt on the slag apparent viscosity were investigated. As slag cleaning proceeded in an electric furnace, the magnetite gradually transformed into ferrous oxide, increasing the FeO/SiO2 ratio. With this ratio increased from 1.2 to 2.0, the slag structure was simplified, and its apparent viscosity decreased from 0.26 to 0.12 Pa·s at 1523 K. The iron phase was excessively reduced to metallic state; the slag contained metallic copper-iron alloy particles, increasing apparent viscosity. The apparent viscosity and phase structure of the slag corresponding to the iron phase reduction process were analyzed in detail; the results obtained in the present study are of great significance to the reasonable control of the converter copper slag cleaning process.

Nov 7, 2022

By Nai-piu Tong, Huaren Dou, Sui-shun Poon, Leslie H. Swann

This paper mainly presents geotechnical aspects of a vehicular underpass that was built across under one of the busiest highway in Hong Kong. The underpass, in a section comprising an upper arch and invert slab, is approximately 6.2 m high at crown and 15 m wide at the base level with 40 m in length. The construction inevitably requires the underpass to be built using tunneling techniques to keep the overheadroad traffic uninterrupted. The paper will describe the design of temporary support for the tunnel excavation that was provided by an arch formed with horizontal pipes, which were installed using the pipe ramming method. The pipes arch was then supported by steel ribs founded on rock or mass concrete. Permanent lining design consideration was also discussed. Results of numerical modeling of the soil-structure interaction using the 2-D computer code FLAC will be presented. The predictions have been compared to the monitored results during construction, which indicates the prediction is in reasonable agreement with the measurement in the light of ground movement. The construction challenges will also be discussed in the paper.

Jan 1, 2003

By M. M. Veras, C. H. Sampaio, A. S. Young, D. Neto, C. O. Petter

"Due to new technological developments, automatic sensor based sorting has made progress within industrial minerals, precious metals, diamond, and coal mining in recent years (Lessard et. al. 2016). In order to re-introduce the technology to other mining sectors, this research discusses its application to iron, manganese, and zinc ores through test works performed by the authors. These test works were performed using Dual Energy X-ray Transmission (DE-XRT) sensor technology. In each case, pre-concentrations of the ore were created demonstrating the possibility to reduce waste material, energy costs, and water consumption while improving product quality of the ores. INTRODUCTION Sorting of mining ores is as old as mining itself (Salter, 1991). Sensor based sorting applications in coal mining began as early as the late 19th century (Louis 1928). New sensor technologies were developed and implemented sequentially for uranium, nickel, coal, and gold mining (Refining, 1949, Rose et al, 1950, Bloomfield et al, 1966, Clayton et al, 1987, Robben and Mosser, 2014). While these sensor technologies were developed decades ago, computational capacity to keep pace with the vast amount of information required utilizing the sensor technology did not arrive until recently (Lessard et. al., 2016). The sensor based sorting (SBS) process was effectively described by Salter and Wyatt in Minerals Engineering in 1991, and Wotruba and Harbeck in 2010 in the Ullmann’s Encyclopedia of Industrial Chemistry under Sensor Based Sorting. Both descriptions include the following key steps: 1. Presentation of the material or particles. 2. Examination or detection of the material or particles. 3. Processing or analysis of the data generated. 4. Physical separation of the material or particles by external means. Effective presentation of the material or particles is achieved when the sensor is capable of identifying each particle individually. This step requires that each fragment of the material be isolated, and it often involves acceleration of the material fragments by chute or mechanical means, as well as the spreading of particles by vibratory feeders (Salter and Wyatt, 1991, and Wotruba and Harbeck, 2010). The isolated particles typically are conveyed into an area wherein they are subjected to electromagnetic irradiation (except in cases of some radioactive ores), either in the form of x-ray, visible light, infrared, or other energies. A wide range of applications for sensor based sorting exists in the literature. The majority of applications fall into one of two camps, (1) pre-concentration of mineral ores, or (2) characterization of the material during processing (Buxton and Benndorf 2013). While there is much to be gained from in-line material characterization and the resulting control both of quality and processing, this article focuses primarily on the camp of pre-concentration of mineral ores."

Jan 1, 2017

By K. G. Tan

Widely available silver and arsenic bearing concentrates can be smelted to produce a discardable slag, a base metal speiss, and a crude silver button which is easily separated from the other phases after solidification. This paper discusses the development of a novel process as an alternative to existing nitric acid leach methods for the production of high purity silver from the raw silver button. Direct electro-refining of the raw silver anode in a sulphate medium is integrated with downstream purification and recycling modules that are customized to allow efficient recovery of silver and saleable by­products. The test results, flowsheet alternatives and process details are presented and discussed in terms of overall technical feasibility, economical viability and environmental compliance considerations.

Jan 1, 1999

By John A. Herbst, Kuang Y. Lee

Coarse particle size measurement is essential for the automatic control of a size reduction process like crushing or SAG milling in order to achieve optimal process performance. However, the on-line size measurement of coarse material is not easily obtained due to the problems of material handling and sample statistics. A technique based on advanced image analysis and quantitative stereology has been successfully developed and tested in a pilot scale setting. The chord length distribution of coarse particles on a moving conveyor was measured with an image analyzer and then transformed to the mesh size distribution with a stereological model and a special numerical method. Some test results as well as the technique's industrial suitability and limitations of this method are also discussed.

Jan 1, 1992

By Carl R. Peterson, John Herrick

INTRODUCTION The need for substantial advances in underground excavation technology has produced considerable research activity on a wide variety of concepts under a variety of Government funded programs. One goal of this "Rapid Excavation" effort has been the development of a means to apply the well-known virtues, both technical and economic, of the drill and blast method in a continuous process. The spiral blast concept, aimed at this specific goal, has been funded for initial studies (1) by the ARPA Rapid Excavation Program and, for the experimental work reported herein, by the Department of Transportation (2). The economy enjoyed by the drill and blast method stems from two factors: explosive energy is relatively cheap; and this energy is released so as to cause rock fragmentation largely through tensile failures. The relative ease and efficiency of tensile rock failures have long been recognized. The drill and blast process of course cannot be truly continuous since drilling and blasting (and other necessary functions) simply are separate, distinct operations. Although some surface explosive work has been done to avoid the need for drilled blast holes (3) it does appear that the high performance associated with explosive excavation requires placement of the explosive beneath the rock surface. This paper describes studies of blasting pattern which, in simplest terms, replaces the occasional heavy blast of conventional practice with frequent, much smaller blasts. The objective, of course, is to reduce the size of individual blasts

Jan 1, 1974

While SME is hosting its Annual Meeting at the Phoenix Convention Center, Feb. 28 to March 3, one of the finest collections of mining history will be on display just 15 blocks away at the Arizona Mining and Mineral Museum. Inside the museum, visitors will be treated to a treasure trove of minerals, gems, me¬teorites, rocks, fossils, mining artifacts, historical exhibits and interactive displays on modern mining. The museum is located at 1502 West Washington. For SME Annual Meeting attendees, this is a free, eight-minute Dash bus ride 15 blocks west of the Phoenix Convention Center.

Jan 1, 2010

By M. E. Gershon

An approach for scheduling the mining of ore and waste blocks in a surface mine is presented. While mathematical programming approaches have been developed to solve this problem optimally, they are difficult to implement and understand. The more simplistic approach presented here achieves practical mining schedules, taking into account both long- and short-term considerations. The key to the approach is use of the concept of ranked positional grade. The program can determine a complete schedule for a specified time period, or it can be used interactively as a guiding tool for the engineer.

Jan 1, 1988

By K. Rushdi, B. E. Abulnaga

The conventional Froude number is blind to the presence of solids, their density and their concentration in a stream of slurry mixture such as tailings flowing in an open channel. This often leads to rough approximations of subcritical, critical and supercritical regimes, based on one phase flow Froude number, limiting subcritical to a value smaller than 0.8 and supercritical to values above 1.4, as proposed in the past by Green, Abulnaga and other authors. While acceptable for small flows, such approximations can be uneconomical for the larger flows encountered in some modern plants that treat up to half a million t/day. A review of concepts of a densimetric Froude number sheds some light on the effect of solids on stratification prior and subsequent to a hydraulic jump. While the approach is heavily borrowed from modern sedimentology, it provides a useful tool to designers of large launders or open channel tailings systems. These concepts are reviewed with some practical examples.

Jan 1, 2013

By Peng Gao

Coal-based reduction followed by magnetic separation is an innovative technology used in processing refractory iron ores. Given that size is essential to the separation of the metallic iron from the gangue, the morphology of metallic iron particles and their evolution during coal-based reduction are investigated in the present work. The size of the metallic iron particle increased from 128.76 µm to 565.70 µm when the reduction time increased from 20 min to 60 min at 1,225° C and C/O (i.e., the amount of coal addition in terms of the gram-atomic ratio of the fixed carbon in the coal added to the combined oxygen in iron oxides) of 2.5. Based on our microstructural and metallographic analysis, the iron ore reduction process can be divided into three stages: (1) metallic iron particle formation, (2) iron oxide reduction and metallic iron assembly and (3) metallic iron particle growth. Almost all iron oxides are reduced to metallic iron in the second stage. These newborn metallic iron particles are energetically active and able to assemble and grow, and are eventually separated from the gangue. The large metallic iron particles benefit the subsequent magnetic separation process.