Search Documents

By B. K. Cantrell

A miner working in an underground coal mine with diesel equipment is exposed to a wide array of pollutants from the diesel exhaust. These include CO, CO2, NO, NO2, SO2, diesel-exhaust aerosol, and a variety of hydrocarbon compounds. A quantitative definition of the health risk resulting from these exposures remains elusive, but during the past several years, progress has been made in defining the problem. Results from epidemiological studies by Garshick, et al. (1988); animal inhalation studies by Mauderly, et al. (1986); Iwai, et al. (1986); and Brightwell, et al. (1986); and in vitro studies by Lewtas, et al. (1986), have provided sufficient data for the National Institute of Occupational Safety and Health (NIOSH) to recommend that "whole diesel exhaust be regarded as a 'potential occupational carcinogen,' as defined in the Cancer Policy of the Occupational Safety and Health Administration," NIOSH (1988). NIOSH further stated that "though the excess risk of cancer in diesel-exhaust-exposed workers has not been quantitatively estimated, it is logical to assume that reduction in exposure to diesel exhaust in the workplace would reduce the excess risk."

Jan 1, 1990

By Charles D. Litton, Ronald S. Conti

This report describes the results of research conducted in the Bureau of Mines Experimental Mine at Lake Lynn Laboratory to determine the effects of air velocity, sensor spacing, and stratification of CO levels on the detection of slowly-developing coal/conveyor belt fires. In general, the time to detect a developing fire is calculated assuming an average CO level that has mixed completely with the ventilated airflow. The data indicate that CO sensors placed near the roof of an entry take advantage of buoyant- induced stratification of combustion products, resulting in earlier detection of developing fires. Even during the low-temperature, smoldering stage of a fire, the combustion products will tend to stratify near the roof, and once flaming occurs, the degree of stratification increases markedly. As one would expect, at higher air velocities, the degree of stratification is less than at lower air velocities, although still significant, especially during the flaming stages of the fire

Jan 1, 1993

By William J. Maloney

Blind drilled shafts are becoming increasingly popular as a secondary and sometimes primary means of ventilation. This is particularly true in the Appalachian coalfields. Some reasons for the rebirth of blind shafts are economics, timeliness, safety characteristics and their inherent independence from underground operations. Blind drilling has had limited use in hard rock and tunneling ventilation. Advances in cutters, bit design, equipment and lining systems have made blind drilled shafts the shaft construction technique of choice for ventilation specialists. History of blind drilling Blind drilling's roots include the Nevada test site, the coalfields of Appalachia and Germany, and the uranium mines of Arizona. Early technology was developed using a variety of equipment mainly of oilfield origin. Shafts completed by oilfield equipment ranged from the shallow 1.5 and 1.8 m (5 and 6 ft) lined shafts on the Nevada test site to two 3 m (10 ft) lined, 222 m (730 ft) deep shafts in Alberta for heavy oil development. Several of these shafts were completed to extraordinary depths. The record, completed in 1969, is a 2.28-m-diam (90-in.-diam), 1875-m (6150-ft) deep shaft, located in the Aleutian Islands of Alaska.

Jan 1, 1993

By E. Haug, Quamrul Ahsan, R. Norcross

Cyanide leaching is the most common process employed in the majority of the gold extraction plants. These gold extraction plants naturally generate tailings and/or effluents that contain highly toxic cyanides, In geographic locations with excess precipitation and therefore net positive water balance, a portion of these tailings must be discharged. Before these highly toxic cyanide-containing effluents can be discharged to the waterways, cyanide and any other toxic substance must be destroyed. Geographic locations with high evaporation and low precipitation, as in the western USA, result in net negative water balance and therefore these plants can operate with a zero discharge option. However, with the current stringent environ­mental regulations and concerns for bird and wildlife mortality, even these operations may be required to partially treat their tailings to preclude potential harm to wildlife. Furthermore, heap leach opera­tions are now generally required to detoxify the heaps before abandonment. It is, there­fore, apparent that all gold extraction plants may be required to install some form of effluent treatment in order to achieve the above objectives,.

Jan 1, 1990

By Emil Szaks

[A great number of papers have been presented at various Engineering Society meetings on the Unit Train subject. Moat are descriptions of facilities that have been constructed or are abort to be built. Many describe the facility as being the World's fastest, newest, largest, incorporating the latest technology and so forth, Many are duplications of installations that have been recently constructed, sort of carbon copies but perhaps arranged differently. The trend has been to incorporate loop tracks, rotary dumpers, indexers and, of course, the snivel coupler equipped unit train. How that the energy crisis has increased the use of coal, there has been a tremendous Increase in applications for permits to construct rail to river coal loading facilities. This paper is different. It does not describe any single existing facility, but is given to alert prospective terminal owners and engineers that there are items that require considerable study and evaluation beside merely selecting an indexer, car dumper, stacker, ship or berg loader and so on. An important item is the selection of the railway car which in turn can affect the selection of the method of loading and unloading. Let us list a few of the items that should be considered and discuss the areas that require examination:]

Jan 1, 1979

By Zefang ChenLi, Laijun Ma, Lei Mao, Fang Lian

"In our work, the preparation technique of high pure manganese sulfate directly from low-grade rhodochrosite ore (MnCO3) was studied and improved intensively, including the effective leaching process and the short purifying process. Based on the same ion effect, the repeated leaching of rhodochrosite with sulfuric acid is proposed to improve the solubility of Mn2+ and inhibit the dissolution of the impurities Ca2+ and Mg2+. Moreover, the repeated leaching process could make full use of rhodochrosite and lower the dosage of sulfuric acidas raw material. With the aid of theoretical calculation, Ba(OH)2 was chose to adjust the pH value of manganese sulfate solution, and BaF2 to remove Ca2+ and Mg2+completely in the process of purifying. The results demonstrate that the extraction ratio and the recovery ratio of manganese reached 94.3% and 92.7%, respectively, which shows the prospect of industrial application. In manganese sulfate production, the heavy metal impurities have been decreased to less than 1ppm. Moreover, the content of calcium, magnesium and sodium has been decreased to less than 20ppm, which meets the standards of high pure reagent for energy and electronic materials. Our study enlightens an approach to the sustainable application of low-grade rhodochrosite.Introduction Low-grade manganese carbonate ores (=14%) becomes gradually the main resources for exploitation and applications in China according to national mineral resources survey (Tan et al 2004 and Singh et al 2017). Therefore, the electrolytic deposition technique of rhodochrosite faces great challenges including low electrolysis efficiency, high-resource input and high-pollution discharge (Fu et al 2010, Michelis et al 2009, Zhang et al 2013). Recently, more and more amount of manganese series with high or super high purity such as MnSO4, MnO2, Mn3O4 and MnO is demanded with the development of energy and electronic materials. Due to low-grade ores containing multiple elements such as iron, silicon, calcium and magnesium, conventional preparation of manganese sulphate with high purity from electrolytic product is characterized by long production-cycle and high-energy consumption (Subrat et al 2011, Mpho et al 2013). By contrast, hydrometallurgical method combined with thermal decomposition, hydrothermal synthesis and sol-gel processes has been widely studied because of its high efficiency, low consumption and low cost (Chen et al 2008). But the key problem in direct preparation of manganese series form low-grade rhodochrosite is to remove completely the multiple impurities such as iron, silicon, calcium and magnesium (Liu et al 2014). So it is urgent to develop a sustainable alternative approach with character of short process, high efficiency and environmental friendly."

Jan 1, 2017

By Patrick Linzer

The majority of existing models describing (methane) gas transport within, and liberation from, coal structures treat these as continua wherein two main gas flow modes (diffusive and Darcy permeable) prevail, and use finite difference techniques to generate solutions to the resulting multivariate parabolic partial differential equation(s). Isotropy and homogeneity in the physical and geometric coal structure properties are often assumed, and the existence of fundamental random fluctuations in these proper- ties is not catered for. The model proposed herein does not suffer these inadequacies, and its efficiency is enhanced by the replacement of the diffusion equation by an accurate approximation. Dynamic mining activity, gas contributions made by the geology surrounding the mining seam, goafing of overlying strata and the effects of induced strain are all taken into account.

Jan 1, 1995

By Paul D. Chamberlin

In the author's selenium report of 1994 (1), the literature was culled for selenium removal technologies that had a chance of producing effluents with <10 ppb of total selenium. Very few processes could achieve such low concentrations. The EPA dictates such low concentrations. Discharges to fishery waters must be <5 ppb total selenium. The federal max­imum contaminant level ( MCL) for drinking water is 50 ppb. The EPA regulations are for total selenium, not for the species, perhaps because an approved EPA assay method is atomic absorption and it cannot distinguish between species.

Jan 1, 1996

By Gerald H. Luttrell, Roe-Hoan Yoon

Flotation columns are becoming increasingly popular due to their ability to improve selectivity and to reduce operating costs. Unfortunately, these advantages are not often realized because of poor operating practices and difficulties associated with design and maintenance. This article provides guidelines for the operation and design of columns. The discussion will focus on designing proper wash water systems for improved selectivity, maximizing throughput by increasing the bubble surface area rate, and minimizing operating and maintenance costs. It is suggested that the design of the air sparging system is the most critical element in column flotation.

Jan 1, 1993

By Leonardo Rosas Sánchez, Darío Ángel Bulla

"The two track road sector between Cisneros-Loboguerrero (having a length of 14 km and 11 short unidirectional tunnels) is a new highway still on construction located along the existing Highway Buga – Buenaventura (Colombia). Due to the steep topography, difficult geological/geotechnical conditions, the traditional portal construction approach was impossible to be implemented in eleven (11) of the twenty two (22) portals. In this specific project, the skewed portal approach was developed as the optimal and more effective solution. The construction time and costs of portals were reduced in 21 months and 75%, respectively. At the same time, the natural equilibrium of the slopes was maintained, thus, facilitating adequate safety factors along the useful life of the project. This document pretends to show a detailed design experience (and the construction of the entry portal of tunnel 11 (left)). INTRODUCTION The Cisneros-Loboguerrero project is a 14 km length dual lane highway, connecting productive zones with the Pacific Ocean along the current Bogota-Buenaventura highway as shown in Figure 1. The project is located at the northern side of the Dagua River Valley. The preliminary design suggested constructing portals under challenging topographical conditions, i.e., slope cuts having heights between 50 to 100 m (some having slopes > 100%) requiring complex developments and having very high risks.The entry portal of tunnel 11 (left) was the first portal successfully built by implementing the skewed portal approach. Later, this approach was used as a model for the construction of the other ten (10) portal having similar topographic and geotechnical conditions. The development of this new alternative provided a considerable reduction on the construction time of portals, thus relieving a critical path in this project."

Jan 1, 2016

By Yang Ge, Yuzhu Pan, Mansheng Chu, Jue Tang, Cong Feng, Lihua Gao, Zhenggen Liu

Increasing attention is being paid to laterite nickel ore as an alternative to nickel sulfide ore to act as a feedstock for nickel metal production. While laterite nickel ore accounts for a lion’s share of global nickel resources at approximately 72 percent, it accounts for only 42 percent of the world’s nickel production. In addition, the processing of nickel sulfide ore is confronted with enormous challenges due to deeper drilling requirements, higher production costs and depleting reserves. The nickel content in the nickel laterite ore associated with hydrated iron oxides and silicate minerals limits the application of physical beneficiation methods for the removal of iron. Thus, magnetic reduction roasting followed by magnetic separation has been regarded as one of the attractive routes to concentrate and separate the valuable metals from the impurities. 

By Dale R. Ralston, Roy E. Williams, Gerry V. Winter, George L. Bloomsburg

It is imperative that the hydrogeologic frame- work and the ground water flow systems of a Potential mine area be investigated prior to initiation of mining. Such investigations are necessary so that potential mine water inflow problems can be anticipated and controlled. Obvious difficulties can arise if large inflows of ground water occur in underground workings. Costs of water removal and disposal, if not foreseen and included in economic planning, can severely limit or eliminate profit from a mining operation. Safety problems associated with large inflows are an additional potential problem. The inflow of water into a mine necessarily alters the associated ground water system. The inflow also may impact nearby surface water regimes, depending upon the interaction of the surface water and ground water systems. The inflow of water into a mine inevitably causes a decline in the ground water levels in the vicinity of the mine. This decline may be restricted to a small area or it may extend a considerable distance, depending upon the hydrogeologic properties of the associated hydrostratigraphic units. A decrease in surface flow will result if the area of ground water level decline intersects a stream or spring that is hydraulically connected to the ground water system. Mine inflow problems historically have been evaluated after-the-fact. Premining hydrologic investigations only recently have been initiated. Brown&apos;s (1977)* report on anticipated hydrologic impacts of oil shale mining in the Piceance Basin of Colorado is an example of premining hydrologic planning. Observed difficulties inherent in designing a data collection network and then utilizing the data to predict mine inflow have led us to the preparation of this manuscript. This manuscript reflects a two-phase effort. The first phase describes and develops analytical and numerical techniques for mine inflow prediction. Emphasis in this section is placed on the selection and application of data collection techniques and data analysis procedures. The second phase applies the prediction technique(s) developed during phase 1 to two existing mines. The objective of phase 1 efforts is to evaluate the hydrologic variables associated with surface water systems and ground water systems that can affect the inflow of water into an underground mine. Subsequently these variables are incorporated into predictive techniques for estimating underground mine water inflow and its effect on associated ground water and surface water systems. The specific objectives of phases 1 and 2 are to: 1) Determine the hydrologic parameters required for predicting underground mine water in- flow and the potential effects of the inflow on surface and ground water systems. The hydrologic parameters represent both premining and past initiation conditions. 2) Outline methods for obtaining the necessary input data for the predictive techniques in pre- mining and post initiation periods. 3) Present existing numerical techniques for predicting underground mine water inflow including assumptions Ad required input. 4) Evaluate existing numerical techniques previously tabulated based on their applicability to mine water inflow prediction. 5) Attempt to develop analytical techniques for predicting underground mine water inflow. 6) Develop, through modification of existing models, a general mathematical model as a numerical technique for predicting underground mine water inflow and the resultant effects on surface and ground water systems. 7) Apply the predictive techniques to two existing mines selected for this purpose. 8) Compare the predicted inflow rates to measured inflow rates at both mines. 9) Compare predicted impact on district hydrology to observed impacts where possible. 10) Evaluate the predictive technique.

Jan 1, 1986

By D. G. Millette, A. J. S. (Sam) Spearing

The design of a cost effective backfill system involves many aspects and various inputs from different engineering disciplines. Backfilling is a very significant mining cost and efforts need to be made in the design stage to maximise efficiency and flexibility whilst minimising costs. The aspects that need to be considered include the following: Required fill performance underground Peak and average fill tonnage requirements Backfill scheduling in the mining cycle Material selection, testing and preliminary costing Plant design and storage needs Infrastructure requirements Implications on surface waste/tailings disposal and costs Total backfill costs In order to produce a cost effective and efficient backfill operation, a multi-disciplinary project team is required that should include the following skills and functions: Mine Planning Rock Engineering Metallurgy Mechanical Engineering Environmental Health and Safety Tailings Disposal/Waste Management This paper discusses the above and indicates important aspects that should be considered.

Jan 1, 2001

By E. M. Frizzell

Decisions affecting ground control design require detailed knowledge of roof rock geology. This is especially true when weak roof materials and anomalies create hazardous conditions and. if not properly supported, result in roof falls. The U.S. Bureau of Mines has developed a system to evaluate geological conditions by using a roof drill that will provide an estimate of the compressive strength of the roof rock in real time. Through the use of sensors and a microcomputer on the roof drill critical drilling parameters can be interpreted and analyzed almost instantaneously, making it possible to inform an operator of hazardous roof conditions such as voids and changes in strata during the drilling process. Geotechnical data can be downloaded to a portable semiconductor memory device, which is brought to the surface so that data can be directly accessed with a personal computer for further analysis. Results from field tests are presented.

Jan 1, 1992

By Hans von Michaelis

This paper examines the process options available for treatment of "refractory" gold ores. As more and more of the easily leached oxidized gold ore zones are exhausted, the pressure is on to find more economical ways of treating refractory gold ore deposits. Historically, refractory ores were generally concentrated, e.g. to make a flotation concentrate that could be roasted. A major development is taking place in the USA in which ores from which gold cannot be concentrated well by flotation are being treated using whole ore oxidation processes prior to cyanidation. Refractory gold ore treatment processes are generally expensive to install and operate. Thus, for a refractory gold ore project to be economically viable, the grade must generally be higher than for free milling gold ores.

Jan 1, 1993

By Roy M. Fleming, Christine B. New

The federal standard for limiting exposures to miners from radon daughters was reduced from 12 working level months (WLM) per year to 4 WLM per year in 1971. However, even at that time some researchers were concerned that the new limit would eventually be shown to result in an excess risk for lung cancer mortality in miners. The National Institute for Occupational Safety and Health (NIOSH) is now engaged in a comprehensive review of this topic. As the lead agency in this project, NIOSH has developed a work plan and established a work group to implement this plan. The procedure and specific considerations are outlined in the work plan for developing a comprehensive ionizing radiation standard recommendation for all miners, underground and surface. Such a recommendation will not only include estimates of health risks at various levels of exposure, but also appropriate recommendations for medical monitoring, sampling and analytical methods, sampling strategies, posting, engineering controls, personal protective equipment and recordkeeping. The work group has twenty-four members. Eleven members are NIOSH personnel representing six divisions of the Institute. The remaining thirteen members represent other federal agencies, specifically the Bureau of Mines of the Department of the Interior, the Mine Safety and Health Administration and the Occupational Safety and Health Administration of the Department of Labor, the Office of Radiation Protection of the Environmental Protection Agency, and the Bureau of Radiological Health of the Food and Drug Administration, Department of Health and Human Services. Several factors contributed to the decision to initiate this project. First, the efficacy of the current standard was considered. An initial study group was formed in the spring of 1980 by NIOSH to identify and evaluate articles that contained information on lung cancer mortality risks at and below the present permissible exposure limit. The conclusion drawn from their evaluation was that a two-fold excess risk of lung cancer mortality at and below 120 cumulative working level months (CWLM) of exposure to radon daughters is evident. This composite indication from selected studies was of sufficient magnitude to justify further evaluation. The study group, however, recognized that other studies and information must also be considered in a quantitative risk assessment which would form the basis for recommending an acceptable and feasible permissible exposure limit. A second factor in the decision to pursue further evaluation was the gaps in the current standard that had previously been identified by the Mine Safety and Health Administration (MSHA). These included lack of medical monitoring of underground miners and absence of regulations for surface miners. The seriousness of the health hazard relative to other hazards in mining was also considered. Along with exposures to silica and asbestos fibers, radiation was judged to be one of the major health hazards in mining, These combined factors constituted the justification to develop criteria and recommendations for improved mandatory health standards. The development process begins with a survey and review of the available world-wide information on the topic, including data and information developed by NIOSH. The end product of this review is to be a document that will contain an evaluation of the collected information and support for any recommendations that are made. To develop this document, the present work group has been divided into five task groups with the following emphases: Health Effects, Medical Aspects, Monitoring, Environmental Exposures, and Engineering Controls and Work Practices. The Health Effects task group is to evaluate the evidence from epidemiologic and animal studies of adverse health effects associated with all forms of ionizing radiation encountered in mining and milling operations. The "weight-of-evidence" of the results of all relevant and useful studies will be summarized, with the reasons for emphasizing the cited studies. The critical cells or tissues and the factors that should be considered in estimating the dose to these areas from various types of radiation will be identified. An evaluation will be made of the possible impacts of smoking and exposure to diesel exhaust on the determination of health effects related to radiation. The implications of biologically redundant dose in terms of the time between tumor initiation and death will also be analyzed. The Medical Aspects task group is to review the generally-accepted and the state-of-the-art medical technology for the detection of adverse health effects from ionizing radiation exposure. An evaluation will be made of the accuracy of urine and fecal analysis, wholebody counting, chromosome analysis and nose blows, as well as their usefulness for early detection of adverse health effects. Early detection is of little utility to the affected individual unless subsequent medical care can improve the prognosis. Recommendations for screening tests will be made after carefully considering the accuracy of the diagnostic procedures and the usefulness of early detection. Required recordkeeping and transfer rights will also be addressed. The Monitoring task group is to consider the state-of-the-art technology for the monitoring of occupational radiation exposures. Instrumentation, sampling strategies and analytical procedures will be reviewed for both personal and area sampling. The implications of the associated levels of confidence for non-compliance decisions will be evaluated. The discussion will also include an evaluation of the feasibility of replacing present monitoring systems with recent technology and the impact that a possible lower permissible exposure limit would have on monitoring requirements. The Environmental Exposure task group is to investigate the field procedures and mathematical methodologies which have been used to quantitate exposure levels to the various kinds of ionizing radiation. The magnitude and direction of the possible biases in past exposure assessments will be estimated. Specific attention will be given to the controversies concerning the quantification of the biological dose equivalent and the feasibility of recommending standards for mixed radiation exposures which use "rem" as the unit of measurement. The Engineering Controls and Work Practices task group will analyze the advantages and limitations of

Jan 1, 1981

By Y. Zimmels, C. Feldman

Closed-circuit grinding processes are considered in the context of a reactor-separator circuit that involves multifraction streams and products. Because grinding circuits are low-efficiency, capital-intensive operations, modeling to maximize their economic return is appropriate. An attempt to develop and test such a model is presented in this work. The model relies on process simulation for both the mill and the separator, in conjunction with constraints imposed by product specifications. The grinding process was simulated using breakage functions, which provided complete data on the feed and product of the mill. A cyclone bank used as the separator was also simulated using known models. The overall process model provided a complete simulation of the multistream grinding and separation process. The process model was then incorporated into an economic model that predicts grinding cost, subject to process constraints, for a given set of operating variables. The model facilitates economic optimization of the grinding process as it relates to process variables and process hardware.

Jan 1, 1993

By W. E. Roscoe, K. N. Spence

In the Canadian mining industry, there are at present no comprehensive regulations or standards for valuation of mineral properties. In January 1999, the Mining Standards Task Force of the Toronto Stock Exchange and the Ontario Securities Commission recommended that the Canadian Institute of Mining, Metallurgy and Petroleum (CIM) establish a committee to review and advise on approaches and methodologies for the valuation of mineral properties. The authors were subsequently appointed Co-chairs of the CIM Special Committee on Valuation of Mineral Properties (CIMVal). A committee of experts from the mining industry, consulting, financial and legal communities was established with the task of reviewing available information, investigating various valuation methodologies and practices, soliciting input from interested parties, and recommending a Canadian code or standards plus guidelines for the valuation of mineral properties. As an initial stage of its work, the CIMVal Committee organized a one day session at the Mining Millennium 2000 Convention in Toronto in March 2000 on valuation of mineral properties. The 10 invited papers have been published by CIM. As a second stage, CIMVal has requested input and comments from all interested parties. The next stage will be to prepare a preliminary draft with a recommended code or standards and guidelines. This will be circulated for further input and comments prior to revision and publication of another draft. The final CIMVal report should be completed in early 2001. A variety of methods are in common usage for the valuation of mineral properties, depending on the stage of development of the property, the data available and the experience of the valuator. For example, the discounted cash flow method is commonly used for properties in production or at the feasibility stage, but is not generally considered appropriate for exploration properties. Market approaches such as comparable transactions are in wide general use, and various cost approaches are used for exploration properties. The option pricing approach has promise for valuation of marginal properties, but is not commonly used.

Jan 1, 2001

By S. Aktas

The present work describes an investigation of a hydrometallurgical process for the recovery of mercury from spent silver oxide button cells. The cell paste was leached in nitric acid to solubilize silver, mercury and zinc. The optimum leaching conditions, in which mercury is entirely converted to Hg2+ ions and, therefore, does not coprecipitate with silver chloride during treatment with potassium chloride solution, were 1.0 M HNO3, 45° C, 1 hour and 200 rpm. After the silver was removed from the solution, mercury was cemented out with zinc powder with an efficiency greater than 99%. In the cementation experiments, the amount of zinc powder, shaking rate, temperature and solution pH were investigated in detail. The mercury recovery (%) increased as the amounts of zinc powder and the temperature were increased. Zinc hydroxide was precipitated from the waste solution by the addition of sodium hydroxide. The Zn(OH)2 precipitate was then converted to zinc oxide. The proposed process is proven to be simple, straightforward and environmentally friendly.

Nov 1, 2011

By S. Aktas

The present work describes an investigation of a hydrometallurgical process for the recovery of mercury from spent silver oxide button cells. The cell paste was leached in nitric acid to solubilize silver, mercury and zinc. The optimum leaching conditions, in which mercury is entirely converted to Hg2+ ions and, therefore, does not co-precipitate with silver chloride during treatment with potassium chloride solution, were 1.0 M HNO3, 45° C, 1 hour and 200 rpm. After the silver was removed from the solution, mercury was cemented out with zinc powder with an efficiency greater than 99%. In the cementation experiments, the amount of zinc powder, shaking rate, temperature and solution pH were investigated in detail. The mercury recovery (%) increased as the amounts of zinc powder and the temperature were increased. Zinc hydroxide was precipitated from the waste solution by the addition of sodium hydroxide. The Zn(OH)2 precipitate was then converted to zinc oxide. The proposed process is proven to be simple, straightforward and environmentally friendly.

Jan 1, 2011