Search Documents

By G. A. Hayes

The range of gold ores tested at AMMTEC LTD over several years has resulted in the requirement to analyse for the mode of occurrence of gold in order to assist selection of ore processing options. The aim of this paper is to describe the laboratory testwork and analytical procedures which have been of benefit in detail­ing the mode of occurrence and mineral associations of gold and hence being of value in developing an optimised ore processing route. The range of ore and mineral assemblages described include relatively simple pyrite and free milling ores, more complex pyrite plus arsenopyrite gold ores and the quite com­plex associations of gold in copper bearing ores or with car­bonaceous mixed sulphide ore assemblages. The aim of this paper is to describe the laboratory testwork and analytical procedures which have been of benefit in detail­ing the mode of occurrence and mineral associations of gold and hence being of value in developing an optimised ore processing route. The range of ore and mineral assemblages described include relatively simple pyrite and free milling ores, more complex pyrite plus arsenopyrite gold ores and the quite com­plex associations of gold in copper bearing ores or with car­bonaceous mixed sulphide ore assemblages.

Jan 1, 1996

By Tyler A. Dawson, Ryan P. Butler, Timothy Gualandri, Jason R. Edberg

"In the early 1920’s, the City of Tulsa, Oklahoma constructed an approximately 8,238-foot long tunnel, the Tiawah Tunnel, through bedrock. Voids behind the concrete tunnel liner were detected via probe drilling in early 2000 as part of an interior visual condition assessment. In 2012 and 2015, conditions along the entire tunnel were efficiently assessed through geophysical investigation using ground penetrating radar (GPR) along the inner tunnel crown and at various select locations within the tunnel. Fifty-seven (57) potential voids, extending up to 19 inches in depth and 12 feet in width, were detected with 1,000 MHz GPR and confirmed through probe drilling with approximately 80% accuracy. GPR proved to be an efficient and reliable technology for void detection behind concrete tunnel lining. This paper highlights the geophysical investigation and how geophysical efforts were combined with other investigation efforts to definitively determine the presence of voids outside of the tunnel lining.INTRODUCTION The city of Tulsa, Oklahoma has a population of about 400,000 people. The original source of water for the city was the Arkansas River. The first pumping operation provided untreated water to homes and businesses in 1904. The residents of Tulsa found this water to be unacceptable due to the high levels of salt and gypsum present. As the city grew, land and storage/treatment facilities were acquired in order to obtain and distribute a more suitable raw water. The raw water needs for the city are currently satisfied by transport and treatment of about 100 million gallons per day (MGD) of water from surface water sources. Water is transported many miles from Spavinaw/Eucha and Oologah lakes to Yahola Lake and the Lynn Lane Reservoir (totaling over 3-billion gallon capacity). From here, the raw water is treated and transported to the various customers (City of Tulsa 2015). The Tulsa Metropolitan Utility Authority (TMUA) is responsible for the operation and maintenance of the raw water transport system."

Jan 1, 2016

By Hans Ehdwall, Erling Strandon, Friedrich Steinhäusler, Victor A. Leach

INTRODUCTION The basis for any measures in radiation protection is the quantitative assessment of the radiation exposure. Due to the extensive requirement in health physics manpower and related cost it is necessary to develop certain criteria regarding the necessity of monitoring and the selection of population groups to be monitored. Depending on the overall objective of the particular programme, the specific requirements for the measurement of atmospheric levels of radon, thoron and their daughters for practical radiation protection purposes differ significantly for those in the case of research applications, such as use of data for epidemiological studies. As part of the OECD-NEA Programme on Radon Dosimetry and Monitoring Task Group 1 reviewed available models for lung dosimetry in the case of inhalation of radon 222, radon 220 and their daughters (James et al., 1981). Using defined reference atmospheres for underground- and open-pit mining conditions as well as for dwellings, normalized conversion factors were calculated for the mean bronchial dose (mGy) per Working Level Month exposure (WLM). Task Group 2 discussed the features and adequacy of the Working Level (WL)-concept as a physical correlative of the absorbed lung dose and its limits of confidence and accuracy (Johnson and Leach, 1981). The WL-concept was found acceptable for radiation protection purposes provided that modifying factors like particle size, unattached fraction and respiratory minute volume did not cause the effective dose equivalent per WLM as calculated by either the James-Birchall or Jacobi-Eisfeld lung models to be more than 50 % above that given by ICRP of 0.01 Sv/WLM. For application in epidemiological studies the WLconcept is considered acceptable if the calculated absorbed dose to the tissue does not vary by more than 50 % (at the 95 % confidence level) from that given for defined reference conditions. In the following, objectives and requirements for the measurement of radon, thoron and their daughters are discussed for operational health physics routine and special research applications according to the scheme outlined in Fig. 1.

Jan 1, 1981

By N. N. Manu

In the Central African Copper Belt, sulfidization flotation is the standard practice for dolomitic copper oxide ores. It is a delicate process, and its plant application requires close control of the reagent addition. This paper presents the results of a thorough laboratory investigation. It features the monitoring, during sulfidization, of the pulp pH, the residual sulfide ion concentration and redox potential. Variables examined during the process were: retention times, sulfidizer additions, pH, collector type, dispersant dosage and reducing agent addition. Implications of the findings for plant application and process control are also briefly examined.

Jan 1, 1994

By R. J. Pruett, J. Yuan

Kaolin clays from five different commercial deposits in Georgia were studied to understand the variations of zeta potential and related fundamental properties. The results suggest that higher negative zeta potential is related to exchangeable or soluble calcium ions in the clays.

Jan 1, 1999

By F. Djahanguiri

The U.S. Bureau of Mines is conducting research on underground stope leaching of metalliferous ores to minimize the environmental impact of ore processing on the surface and to maximize minable reserves. An aspect of this research is to minimize pregnant solution losses and/or groundwater contamination by leach solutions. Bulkhead design and construction are important issues for solution control and stope leaching economics. A reinforced concrete bulkhead was designed, constructed, and tested for solution control in an underground mine near Idaho Springs, CO. This paper presents the bulkhead design methodology and construction procedure.

Jan 1, 1995

By M. Gaft, G. Panczer

Sedimentary francolite and magmatic apatite are characterized by specific laser-induced time- resolved luminescence, which allows phosphate to be distinguished from accompanying dolomite. The "selective window" parameters are: he, = 337 nm, delay time after laser pulse is 0.5-5 ps, and detection spectral range is 400-525 nm. In the case of nonuniform distribution of phosphate minerals, it makes it possible to accomplish lasero- luminescent sorting and to receive intermediate product with a lowered dolomite contents.

Jan 1, 1999

By Behzad Khorshidi

"The ultimate objectives of the post-tensioned strands are to connect the precast segments into a ring and provide pre-stress in the tunnel circumference. The method involves inserting the strand through the preliminary embedded duct in the precast concrete segments and then tensioning the strand by jack and fastening it. The post-tensioned strand eliminates the necessity of bolt connections between the segments and may reduce the labor cost and increase speed of lining construction. Pre-stressing of the segmental lining reduces the steel reinforcement or fiber volume in precast segments and/or thickness of the precast segments which would result in reducing the manufacturing cost of them. Pre-stressing would reduce cracking and increase water tightness, and would provide smooth intrados due to eliminated bolt joints and pockets in the tunnel lining. Pre-stressing would increase resistance to internal pressures as well. Further, this system could work very well structurally in tunnels with squeezing rock or tunnels with high seismic loadings. INTRODUCTION OF THE METHODPost-tensioning is commonly used in the construction of bridges, large buildings, nuclear power stations, and water tanks but its utilization in tunnels is still in its infancy.The precast pre-stressed concrete segmental lining can be used for shield tunnels. It provides a reinforced lining ring by the following construction stages and as shown in Figure 1:1) Segments to be assembled by TBM to complete a full ring2) Steel strand to be inserted through embedded duct (sheath) within the segments3) The strand to be tensioned by Jack after anchorage of the other end4) The strand to be fastened after reaching required tension load5) The horizontal strands (if necessary) to be installed, tensioned and fastened6) The recesses and gap between strand and duct to be filled by groutingFurther, Figure 2 shows an unbonded post-tensioning strand model; Figure 3 shows an anchor sample (Xanchor); Figure 4 shows a duct (sheath) and anchor within reinforcement; Figure 5 depicts the posttensioning of a strand by jack; and Figure 6 is an image of the Midorigaoka Trunk line tunnel in Sagamihara, Japan which was constructed using this system."

Jan 1, 2016

By Misra M., P. Grimes, Chen. S.

The combustion of petroleum products produces emissions which contain oxides of nitrogen (NOx), hydrocarbons (HC), and particulate matter (PM) which have adverse health and environmental effects. In recent years there has been increasing interest in the use of water-fie1 emulsions as a substitute for conventional fuels. Emulsified fuels are emulsions of water in fuel, which are typically made of 10 to 20 percent of water mired with certain additives and fuel. Studies have shown that the emulsified diesel can significantly reduce the emissions of NO, PM and car- bon monoxide and increase the fuel efficiency. In order to produce a stable diesel emulsion, the development of an effective surfactant additive is critical. The stability of diesel emulsions is influenced by many factors, including size distribution of the droplets, the viscosity of the continuous phase, the physical properties of the interfacial film, and temperature. This paper describes a method to produce emulsified diesel and combustion results obtained from various tests. It has been found that the diesel emulsion made with this additive package was stable during the test, and the emissions were lower in NO, CO, and PM compared to the baseline diesel.

Jan 1, 2005

By G. E. Maryniak

To date, human space exploration has been almost completely dependent on the use of resources carried with astronauts and cosmonauts from the surface of the Earth. The only exception to this has been the harvesting of solar energy to power space stations like Skylab, Salyut and Mir for long-duration missions. This dependence on materials which must be transported into orbit at costs in excess of $5000 per pound is the fundamental limiting factor in space exploration and operations. It is likely that launch costs can eventually be greatly reduced by means of such innovations as true single stage to orbit vehicles, aerospace planes, or serial electromagnetic or laser launch systems. However, the Earth will always remain an expensive source of materials for space construction and for basic commodities such as propellant and life support liquids and gasses. Fortunately, abundant sources of materials exist which are already in space, outside of the Earth's deep gravity well.

Jan 1, 1992

By Yu. A. Polozov, V. A. Lagunov, O. Yu. Lushinkova, Yu. I. Svirskiy, Eh. Ya. Kipko, Roy A. Williams

6.1 PRINCIPLES OF PLANNING GROUTING OPERATIONS FOR SHAFTS, DRIFTS AND TUNNELS The planning of integrated grouting of vertical, inclined or horizontal underground workings in saturated, fractured rock includes the following phases: 1. Planning for the collection and analysis of geological information concerning the characteristics of the struc¬tural deformation(s) that produced the details of the frac¬ture system being studied. 2. Planning for the acquisition of initial hydrogeological information produced by the flowmetric and hydrody¬namic investigations (described in Chapters 2 and 3). 3. Computing the initial engineering calculations of the ex¬pected or planned dimensions of the isolation curtains for each water-producing stratum (fracture zone) and the expected areal spreading pattern of the grout in each of these water-producing horizons. The selection of the lo¬cations, the initial optimal number of holes and the vol¬ume of grout needed to create each isolation curtain also are included in this phase. 4. The selection or development of a grout formula for the specific hydrogeological conditions that exist at the site. 5. Identification of a resource (deposit) required to produce the grouting clay. The planning of grouting operations must be supported by the acquisition of all necessary initial data, which in¬cludes: 1. The geographic location and administrative responsibil¬ity (ownership and regulatory constraints) of the mineral deposit and any peculiar features of the area where ex¬cavation of the underground workings is planned. The surface relief, the hydrographic network of the region, and the local climatic conditions must be evaluated prior to planning for buildings and waste discharges if any. 2. The economic status of the region, the available trans¬portation, the nature of the energy base, the water and heat supply sources, the location of construction mate¬rials suitable for making the grout all must be deter¬mined. 3. The geological and hydrogeological characterization of the work site must be accomplished. 4. The technical features of the shaft(s) and underground works must be characterized. 5. The organization's principal initial design plan features and the construction sequence of all buildings and struc¬tures must be developed. These must be correlated with the organization and schedule for excavating the under¬ground works. The technical characterization of a shaft or of other un¬derground workings must contain information about the purpose of the workings, the design depth, the planned excavation procedures along with cross-sections, and the parameters of the lining, if a lining is required. The geology of the section to be penetrated must include geological data obtained from existing exploration activities at the mineral deposit and conclusions about the shaft ex¬cavation conditions obtained from drilling technical moni¬toring holes and exploration drillholes. The interpreted stratigraphic regime, including the thickness, strike and dip of each stratum, must be shown in cross-section. The tec¬tonics, including all geologic structures, must be presented by cross-sections. The bedding orientations must be used to identify anticlines, synclines, monoclines and faults. The lithologic composition and the drillability of the rock com¬prising the section must be examined. The character of the rock's fracture pattern must be presented. Finally the per¬meability, porosity and storage characteristics of each aqui¬fer must be determined by in situ hydraulic property testing (injection tests or pumping tests, as described in Chapter 3). The fracture pattern of the indurated rock is presented in reports derived from geo-exploration borehole studies and from studies of outcrops on the surface and in all nearby underground workings. The extent of each fracture zone is mapped in three dimensions. The distribution of fracture apertures, the nature of the fractures according to each litho¬logic stratum, and the relationship of bedding planes to each fracture system are all determined. Acoustic logs, downhole cameras, caliper logs, oriented core, and any other appro¬priate geophysical tools available are used to construct the data base for this purpose. The hydrogeological characterization of the geologic section to be penetrated by the workings is based on the analysis of hydrogeological data collected during the drill¬ing and testing of technical monitoring holes and from in¬formation on ground water inflow collected during the ex¬cavation of nearby underground workings, if such workings exist. The hydrogeologic characterization must contain the following information: 1. The identification of all aquifers, their thicknesses and their locations in the section, 2. The distribution of hydrostatic head in the ground water in three dimensions, 3. The coefficient of saturated hydraulic conductivity (per¬ meability) of each aquifer, 4. The porosity and storativity of each aquifer, and 5. The projected rate of water inflow into the shaft, drift or tunnel for each aquifer prior to grouting. This step is used to identify the zones to be grouted.

Jan 1, 1993

By Amin Mousavi, Soroush Khazaei, Yashar Pourrhimian

As a factory-like method, sublevel caving consists of development activities, stockpiling and production activities that are carried out on different levels independently. Therefore, considering the operation from the development phase to the plant will lead to more reliable production scheduling. This paper presents a mixed integer linear programming framework for the long-term production scheduling of sublevel caving that maximizes the net present value while satisfying development activities, mining, and processing capacities, continuous mining, the allowable number of active mining units, grade blending, and vertical and horizontal sequencing. The model is coded in Jupyter Notebook and is solved using the CPLEX solver.

Jun 25, 2023

By Pratima Meshram Abhilash

In this review, availability of germanium in primary and secondary resources and its recovery from these resources are presented. With nearly 40% germanium consumed in fiber optics and scarcity of resources, the global consumption outplays the primary production. Germanium exists as a substituted element in zinc sulfide matrix of lead–zinc sulfides and lignites. Nearly 60% of the germanium supply is met by zinc refining residues, and about 20–30% of germanium is produced from coal and its by-products. Germanium recovery from various resources such as zinc plant residues, coal and coal plant waste, spent optical fibers, and copper flue dust has been examined. Bioleaching was exploited by few researchers to extract germanium from zinc sulfides, sulfide tailings, jarosite, coal fly ash, and flue dust. This review covers the various work carried out by different chemical separation processes, viz., chemical precipitation, solvent extraction (SX), ion exchange (IX), and membrane processes, as well as biological approaches.

Jan 16, 2022

By E. R. Bauer

A primary goal of Ground Control Research, Bureau of Mines, U.S. Department of the Interior, is to develop information that can be used by the mining industry to reduce accidents and fatalities due to failure of mine roof. A specific research objective is to determine methods to detect hazardous coal mine roof. This paper reviews the existing and experimental techniques, and describes a recent Bureau of Mines contract research project that resulted in a simple technique and prototype instrument for evaluating mine roof competence.

Jan 1, 1986

Employee safety and health is of paramount importance for SME and its members. Many SME members work daily in our Nation's mines or have a direct impact on others that work in the mines. SME supports the mission and purpose of the U.S. Mine Safety and Health Administration (MSHA), which is to prevent all injuries and disease from mining and to promote safe and healthful workplaces for the Nation's miners. SME supports the National Institute for Occupational Safety and Health and university research geared toward prevention of all occupational injuries and illnesses. SME maintains that laws and regulations governing the mining industry need to be based on sound scientific principles to ensure that workplace solutions can be readily implemented and that solutions to safety and health problems are fully realized.

Jan 1, 2011

By John T. Bartlett

With more stringent environmental and economic constraints being placed on mining operations, it has become necessary to optimize each process to minimize energy and raw material consumption and reduce waste discharge. In most cases, detailed process analysis is required to detect inefficiencies and provide alternative solutions for process improvement. HETSIM, a microcomputer process modeling and simulation system, is routinely used to analyze communition, hydrometallurgical, pyrometallurgical, and coal preparation processes. The process modeling techniques used in METSIM, including process control simulation, will be presented and illustrated using actual plant processes.

Jan 1, 1987

By Steven G. Vick

Not too long ago a mill superintendent, when asked where his tailings were being disposed, could simply shrug his shoulders and point to the open end of the thickener discharge pipe. This “out of sight, out of mind” approach to tailings disposal is a practice of the past. Today there are very few planned hardrock or energy-related mining facilities where tailings disposal has not been identified as the major area of impact and controversy. In fact, development of some ore bodies has been stymied altogether by lack of suitable sites or methods for tailings disposal. The bottom- Iine result is that tailings disposal often controls the permitting lead time and has a significant influence on construction cost (up to 2070 in some cases) of new minemill complexes. The following article, the first in a series of three, explores technical background and historical perspectives on siting and design of tailings impoundment facilities.

Jan 6, 1981

As mentioned in chapter 8, one of the objectives of the budget is to provide a mechanism for ongoing measurement and control of the production operation. The budget shows expected performance. Actual results are compared to this benchmark to evaluate past performance and to direct future activities. The variances between budgeted and actual results identify specific activities that did not perform as expected (whether negatively or positively). Managers who use variance analysis are essentially applying a management- by-exception philosophy. Individual organizations will determine variances that reflect their own processes and managerial interests, but these variances all follow the approach outlined here. Firms will also vary in the extent to which variances are reported. Some firms use a few variance measures for the overall production organization whereas others calculate variances for individual departments or even individual work areas. As mentioned in chapter 5, it is important to distinguish between controllable and noncontrollable costs when using budgets for control and evaluation.

Jan 1, 1999

By Roy H. Patten

When driving a shallow soft ground bore, the appearance of surface craters along the tunnel alinement indicates trouble, particularly when a major highway is intersected. During the excavation of a 3.7 m diam tunnel in Seattle, Washington a chemical grouting program was implemented to stabilize soil conditions sufficiently to allow advancement of the mole without loss of ground. Unanticipated mixed face conditions consisting of saturated running sand and some boulder pockets bedded on top of dense glacial till created excavation difficulties. A discussion of problems and corrective measures is presented.

Jan 1, 1987

By B. J. Arnold, F. F. Aplan, R. R. Klimpel, E. C. Jr. Dowling

Residence-time distribution techniques are useful tools in the analysis, characterization and modeling of the performance of processing equipment and circuits. This paper presents the results of both conventional and more-sophisticated residence-time distribution techniques for industrial copper-flotation-circuit data. While conventional techniques provide a description that is sufficient for macroengineering design requirements, the more sophisticated tracer-technique methods give more realistic descriptions of process flows and system effectiveness. It is demonstrated that these approaches can provide highly useful information about different equipment, as well as its configuration and performance.

Jan 1, 2000